Bosch E2600 User Manual
E2600 DSA E-Series iSCSI Disk Arrays
en Quick Install Guide
E2600 DSA E-Series iSCSI Disk Arrays Table of Contents | en 3
Table of contents
1
1.1 Learn about management methods 4
1.2 What you need for assembly 4
2
3
4
5
6
7
8
9
Before you begin 4
Device view 6
Install the mounting rails 7
Install the controller-drive tray 8
Secure the controller-drive tray 9
Connect the cables 10
Turn on the DC power 13
Turn on the AC power 15
Install and configure the storage array 16
Bosch Sicherheitssysteme GmbH Quick Install Guide 07/2012 | V1 |
4 en | Before you begin E2600 DSA E-Series iSCSI Disk Arrays
1
1.1
Before you begin
For warnings and detailed installation instructions, refer to the E2600 DSA E-Series
Installation manual and additional documentation in the Online Product Catalog on http://
www.boschsecurity.com > Video > Digital Recording and Storage > Disk Arrays (Network
Attached) > DSA – Disk Arrays > DSA E-Series iSCSI Disk Arrays. (The navigation path is
subject to change).
Management methods are specific to the installation steps in Section 6 and Section 9.
Learn about management methods
In-band management
Management using the I/O connections between the host and the storage. The host must still
have Ethernet capabilities.
– Access volume
Used to communicate management requests and event information. An access volume is
needed for only in-band management.
Out-of-band management
Management directly through the Ethernet connections on each controller using one of the
network configurations from the following list (the command line interface CLI might be
required):
– DHCP server
Permits nodes to dynamically acquire network addresses.
– Ethernet IP address
Permits direct connection to controller A or controller B by using an IP address in the
form of xxx.xxx.xxx.yyy and xxx.xxx.xxx.yyz.
– Static IP address
Recommended for out-of-band management using IPv4 networks.
– Router advertisements
Recommended for out-of-band management using IPv6 networks.
– MAC address
Associates the media address control (MAC) address (xx:xx:xx:xx:xx:xx) of each controller
with an assigned IP address.
1.2
07/2012 | V1 | Quick Install Guide Bosch Sicherheitssysteme GmbH
What you need for assembly
E2600 controller-drive tray ship group
– One two-unit (2U) -high E2600 controller-drive tray
– Two power cords
– One cabinet mounting hardware kit, including:
– Two mounting rails (right and left assemblies)
– Eight M5 x 8 mm screws – Use six screws to secure the mounting rails and two
screws to secure the front of the controller-drive tray to the cabinet.
– Two M4 x 8 mm screws – Use the screws to secure the rear of the controller-drive
tray to the mounting rails.
Options
– Drives (two minimum for each controller-drive tray)
– DC power cords for the optional –48 VDC power option
If you have any questions about the firmware or your configuration, contact your Customer
and Technical Support representative.
Tools
– An Internet connection
E2600 DSA E-Series iSCSI Disk Arrays Before you begin | en 5
– A cart to hold the controller-drive tray and its components
– Labels for the cable connections
– A medium flat-blade screwdriver
– A No. 2 Phillips screwdriver
– Anti-static protection
– A flashlight
Bosch Sicherheitssysteme GmbH Quick Install Guide 07/2012 | V1 |
!
1 2 3 4 5 6
1 2
6 en | Device view E2600 DSA E-Series iSCSI Disk Arrays
2
Device view
Controller-Drive Tray (12 Drives) – Front View
Figure 2.1: Front View E2600
1
Standby Power LED 4 Service Action Required LED
2 Power LED 5 Locate LED
3 Over-Temperature LED 6 Drive Canister
Controller-Drive Tray – Rear View
Figure 2.2: Rear View E2600
Controller Canister 2 Power-Fan Canister
1
07/2012 | V1 | Quick Install Guide Bosch Sicherheitssysteme GmbH
Loading...