Bosch DX4010V2 Specsheet

Intrusion Alarm Systems | DX4010V2 USB/Serial Interface Module

DX4010V2 USB/Serial Interface Module

www.boschsecurity.com

u RS-232/USB connectivity

u Enhanced direct connection for Remote

Programming Software (RPS)

u RJ-16 data bus

The DX4010V2 USB/Serial Interface Module creates a
local connection between compatible control panels
and approved applications. The module connects to
the control panel’s data bus which provides power and
data.

System overview

u Transparent enclosure

u Diagnostic light emitting diodes (LEDs)

1. A control panel’s option or SDI bus through the data
bus connector or terminal block connection.

2. A PC for RPS, BIS, or other third party applications
through an RS-232 or USB connection.

3. A serial printer or parallel printer with a converter
cable box (not shown) through the RS-232 connector
with a compatible control panel. Refer to
Compatibility Information for details.

Functions

RJ-16 Data Bus and RS-232/USB Connectivity

Use the RJ-16 data bus connector for a remote
programming connection. Use the DB9 DTE RS-232
connector to connect to approved RS‑232 devices. Use
a USB-A to USB-B cable to connect to a USB port.

Transparent enclosure

The diagnostic LEDs show through the transparent
enclosure, making troubleshooting easy and
convenient.

Diagnostic LEDs

There are four diagnostic LEDs that provide
information about the transmission and receipt of
data.

The DX4010V2 Serial Interface Module connects to:

Two Red LEDs Function

BUS RX Receiving data from control panel

2 | DX4010V2 USB/Serial Interface Module

BUS TX Transmitting data to control panel

Two Green LEDs Function

SER RX Receiving data from serial device

SER TX Transmitting data to serial device

DIP Switches

Use the external DIP switches to easily assign an
address to the DX4010V2 Serial Interface Module.

Certifications and approvals

This product is also designed to comply with the certifications and
standards listed here:

Region Certification

Australia C-Tick

United States FCC

Canada IC

Region Certification

Europe CE 2004/108/EC EMC Directive (EMC),

1006/95/EC Low-Voltage Directive
(LVD); 2011/65/EU Restriction of the
use of certain hazardous substances in
electrical and electronic equipment
[DX4010V2]

Installation/configuration notes

Compatibility Information

Applications and RS-232 Devices

SDI Bus Control Panels (version 6.0 or higher)

United States • All G Series control panels

• D7212, D7412, D9412

• D9112

Australia • D9412GV2-AU

Option Bus Control Panels

Europe • DS7400Xi (version 2.02 or higher)

• DS7220, DS7240, DS7240V2, and
DS7220V2

Australia • CC7240-AP

United States • D4412 and D6412

The DX4010V2 Serial Interface Module replaces the
following modules:

United States D9133 Serial

Interface Module

For use with BIS, PC9000, or
other third party applications
on SDI bus control panels.

D9133DC Serial
Interface Module

For use with RPS or other
third party applications on
SDI bus control panels.

United States,
Europe, and
China

D9533 RS-232
Serial Interface
Module

DX4010/
DX4010i RS-232
Serial Interface

For use with RPS, CMS
7000*, or printers on option
bus control panels

For use with RPS,
CMS 7000*, or printers on
option bus control panels.

Module

*CMS 7000 is available in China only.

United States RPS: Supported on all

compatible control panels.

PC9000: Supported on all the

following control panels:
D9412G, D7412G,
D7212G, D9112, D7412,
D7212.

Building Integration
Software (BIS):

Supported on the following
SDI bus control panels
(version 6.3 and higher):
All G Series control panels
including D9412GV2‑AU

Austrailia Building Integration

D9412GV2‑AU

Software (BIS):

China CMS 7000: Supported on DS7400Xi

Control Panels (option bus)
set at Mode 18 (version

3.09 or higher).

All Printers: Supported on option bus

control panels.

Technical specifications

Environmental Considerations

Operating Temperature: 0°C to +50°C

(+32°F to +122°F)

Relative Humidity: 5% to 85% at +30°C (+86°F)

non‑condensing

Power Requirements

Current (Maximum): 55 mA nominal, 60 mA with LED

Voltage (Operating): 8 VDC to 14 VDC

Ordering information

DX4010V2 USB/Serial Interface Module

Provides a local connection between compatible
control panels and approved applications.

Order number DX4010V2