Bosch DIVAR DIP-6080-00N, DIVAR DIP-6082-8HD Quick Installation Manual

DIVAR IP 6000 2U

DIP-6080-00N, DIP-6082-8HD

en Quick Installation Guide

Table of contents

Safety precautions 4

1.1 General safety precautions 4

1.2 Electrical safety precautions 5

1.3 ESD precautions 6

1.4 Operating precautions 6

1.5 Important notices 7

1.6 FCC and ICES compliance 7

System overview 8

2.1 System interface 8

System setup - hardware 10

3.1 Introduction 10

3.2 Unpacking the system 10

3.3 Preparing for setup 10

3.3.1 Choosing a setup location 10

3.3.2 Rack precautions 10

3.3.3 General system precautions 11

3.3.4 Rack mounting considerations 11

3.4 Rack mounting instructions 12

3.4.1 Separating the sections of the rack rails 12

3.4.2 Installing the inner rails 13

3.4.3 Installing the outer rails to the rack 13

3.4.4 Installing the chassis into the rack 14

3.4.5 Installing the chassis into a Telco rack 15

3.5 Turning on the system 15

System Setup – first Steps 16

4.1 Introduction 16

4.2 Setup instruction 16

4.3 Setting the IP address 16

4.3.1 Remote desktop connection 16

4.3.2 Physical connection 19

4.4 VRM Appliance 21

4.4.1 Default installation 21

4.4.2 Disabling the VRM service 21

4.5 Standard system configuration 21

Additional software and documentation 22

Service and repair 23

DIVAR IP 6000 2U Table of Contents | en 3

Bosch Sicherheitssysteme GmbH Quick Installation Guide 2013.05 | V3 | DOC

Safety precautions

Observe the safety precautions in this chapter.

General safety precautions

Follow these rules to ensure general safety: – Keep the area around the system clean and free of clutter. – Place the chassis top cover and any system components that have been removed away

from the system or on a table so that they won't accidentally be stepped on.

– While working on the system, do not wear loose clothing such as neckties and

unbuttoned shirt sleeves, which can come into contact with electrical circuits or be pulled into a cooling fan.

– Remove any jewelry or metal objects from your body, which are excellent metal

conductors that can create short circuits and harm you if they come into contact with printed circuit boards or areas where power is present.

– After accessing the inside of the system, close the system back up and secure it to the

rack unit after ensuring that all connections have been made.

– The system weighs approximately 57 lbs. (25.9 kg) when fully loaded. When lifting the

system, two people at either end should lift slowly with their feet spread out to distribute the weight. Always keep your back straight and lift with your legs.

Warning!

Interruption of mains supply:

Voltage is applied as soon as the mains plug is inserted into the mains socket.

However, for devices with a mains switch, the device is only ready for operation when the

mains switch (ON/OFF) is in the ON position. When the mains plug is pulled out of the

socket, the supply of power to the device is completely interrupted.

Warning!

Removing the housing:

To avoid electric shock, the housing must only be removed by qualified service personnel.

Before removing the housing, the plug must always be removed from the mains socket and

remain disconnected while the housing is removed. Servicing must only be carried out by

qualified service personnel. The user must not carry out any repairs.

Warning!

Power cable and AC adapter:

When installing the product, use the provided or designated connection cables, power cables

and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fire.

Electrical Appliance and Material Safety Law prohibits the use of UL or CSA-certified cables

(that have UL/CSA shown on the code) for any other electrical devices.

1.1

4 en | Safety precautions DIVAR IP 6000 2U

2013.05 | V3 | DOC Quick Installation Guide Bosch Sicherheitssysteme GmbH

Warning!

Lithium battery:

Batteries that have been inserted wrongly can cause an explosion. Always replace empty

batteries with batteries of the same type or a similar type recommended by the manufacturer.

Handle used batteries carefully. Do not damage the battery in any way. A damaged battery

may release hazardous materials into the environment.

Dispose of empty batteries according to the manufacturer's instructions.

Warning!

Handling of lead solder materials used in this product may expose you to lead, a chemical

known to the State of California to cause birth defects and other reproductive harm.

Notice!

Electrostatically sensitive device:

To avoid electrostatic discharges, the CMOS/MOSFET protection measures must be carried

out correctly.

When handling electrostatically sensitive printed circuits, grounded anti-static wrist bands

must be worn and the ESD safety precautions observed.

Notice!

Installation should only be carried out by qualified customer service personnel in accordance

with the applicable electrical regulations.

Disposal

Your Bosch product has been developed and manufactured using highquality materials and components that can be reused. This symbol means that electronic and electrical devices that have reached the end of their working life must be disposed of separately from household waste. In the EU, separate collecting systems are already in place for used electrical and electronic products. Please dispose of these devices at your local communal waste collection point or at a recycling center.

Electrical safety precautions

Basic electrical safety precautions should be followed to protect you from harm and the system from damage: – Be aware of the locations of the power on/off switch on the chassis as well as the room's

emergency power-off switch, disconnection switch or electrical outlet. If an electrical

accident occurs, you can then quickly remove power from the system. – Do not work alone when working with high voltage components. – Power should always be disconnected from the system when removing or installing main

system components, such as the motherboard or memory modules. When disconnecting

power, you should first turn off the system and then unplug the power cords from all the

power supply modules in the system. – When working around exposed electrical circuits, another person who is familiar with the

power-off controls should be nearby to switch off the power if necessary.

1.2

DIVAR IP 6000 2U Safety precautions | en 5

Bosch Sicherheitssysteme GmbH Quick Installation Guide 2013.05 | V3 | DOC

– Use only one hand when working with powered-on electrical equipment. This is to avoid

making a complete circuit, which will cause electrical shock. Use extreme caution when using metal tools, which can easily damage any electrical components or circuit boards they come into contact with.

– The power supply power cords must include a grounding plug and must be plugged into

grounded electrical outlets. The unit has more than one power supply cord. Disconnect both power supply cords before servicing to avoid electrical shock.

– Mainboard replaceable soldered-in fuses: Self-resetting PTC (Positive Temperature

Coefficient) fuses on the mainboard must be replaced by trained service technicians only. The new fuse must be the same or equivalent as the one replaced. Contact technical support for details and support.

Caution!

Mainboard Battery: There is a danger of explosion if the onboard battery is installed upside

down, which will reverse its polarities. This battery must be replaced only with the same or

an equivalent type recommended by the manufacturer (CR2032). Dispose of used batteries

according to the manufacturer's instructions.

Caution!

DVD-ROM Laser: This system comes without a DVD-ROM drive but if added: To prevent direct

exposure to the laser beam and hazardous radiation exposure, do not open the enclosure or

use the unit in any unconventional way.

ESD precautions

Electrostatic Discharge (ESD) is generated by two objects with different electrical charges coming into contact with each other. An electrical discharge is created to neutralize this difference, which can damage electronic components and printed circuit boards. The following measures are generally sufficient to neutralize this difference before contact is made to protect your equipment from ESD: – Do not use mats designed to decrease electrostatic discharge as protection from

electrical shock. Instead, use rubber mats that have been specifically designed as

electrical insulators. – Use a grounded wrist strap designed to prevent static discharge. – Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready

for use. – Touch a grounded metal object before removing the board from the antistatic bag. – Do not let components or printed circuit boards come into contact with your clothing,

which may retain a charge even if you are wearing a wrist strap. – Handle a board by its edges only. Do not touch its components, peripheral chips, memory

modules or contacts. – When handling chips or modules, avoid touching their pins. – Put the mainboard and peripherals back into their antistatic bags when not in use. – For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and the

mainboard.

Operating precautions

The chassis cover must be in place when the system is operating to assure proper cooling. Out of warranty damage to the system can occur if this practice is not strictly followed.

1.3

1.4

6 en | Safety precautions DIVAR IP 6000 2U

2013.05 | V3 | DOC Quick Installation Guide Bosch Sicherheitssysteme GmbH

Note:

Please handle used batteries carefully. Do not damage the battery in any way. A damaged battery may release hazardous materials into the environment. Do not discard a used battery in the garbage or a public landfill. Please comply with the regulations set up by your local hazardous waste management agency to dispose of your used battery properly.

Important notices

Accessories - Do not place this unit on an unstable stand, tripod, bracket,

or mount. The unit may fall, causing serious injury and/or serious damage to the unit. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer. When a cart is used, use caution and care when moving the cart/apparatus combination to avoid injury from tip-over. Quick stops, excessive force, or uneven surfaces may cause the cart/unit combination to overturn. Mount the unit per the manufacturer's instructions.

FCC and ICES compliance

(only for U.S.A. and Canada) This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense.

1.5

1.6

DIVAR IP 6000 2U Safety precautions | en 7

Bosch Sicherheitssysteme GmbH Quick Installation Guide 2013.05 | V3 | DOC

System overview

DIVAR IP 6000 is an affordable, simple and reliable all-in-one recording management solution for network surveillance systems of up to 64 cameras. Powered by VRM (Video Recording Manager) software, the system is an intelligent IP storage device that eliminates the need for separate NVR (Network Video Recorder) server and storage hardware. The system is a 2U rack mount unit that combines advanced recording management and stateof-the-art iSCSI storage into a single cost-effective, plug and play IP recording appliance for ITminded customers seeking for a state-of-the-art “second generation” NVR recording solution. DIVAR IP 6000 features: – Instant real time access to video

View high quality HD video despite low or limited bandwidth connections. Dynamic

Transcoding technology ensures that you can view your video immediately — anytime,

anywhere. – Remote viewing

DIVAR IP 6000 comes with our advanced Video Client for remote viewing. Video Client is a

Windows PC application for live viewing and playback including Configuration Manager.

Configuration Manager allows the settings of the DIVAR IP 6000 be configured. A stand-

alone archive player will allow archive playback and authentication without any other

workstation software.

System interface

There are several LEDs on the front and rear of the chassis. The LEDs show the over-all status of the system and the activity and health of specific components.

Front view:

1 Power Failure 5 Power

2 Overheat/Fan Fail 6 Reset

3 NIC1/NIC2 7 Power on/off

4 HDD

2.1

8 en | System overview DIVAR IP 6000 2U

2013.05 | V3 | DOC Quick Installation Guide Bosch Sicherheitssysteme GmbH

+ 18 hidden pages