Bosch DIP-7040-00N Installation Manual

DIVAR IP 7000 1U

DIP-7040-00N, DIP-7042-2HD, DIP-7042-4HD

en Installation Manual

DIVAR IP 7000 1U Table of Contents | en 3

1.1 General safety precautions 5

1.2 Electrical safety precautions 6

1.3 ESD precautions 7

1.4 Operating precautions 7

1.5 Important notices 8

1.6 FCC and ICES compliance 8

2.1 Chassis features 9

2.2 Chassis components 9

2.2.1 Chassis 9

2.2.2 Backplane 10

2.2.3 Fans 10

2.2.4 Mounting rails 10

2.2.5 Power supply 10

2.2.6 Air shroud 10

2.3 System interface 10

2.3.1 Control panel buttons 11

2.3.2 Control panel LEDs 11

2.3.3 Power supply LEDs and overheat indicators 12

4.1 Unpacking the system 14

4.2 Preparing for setup 14

4.2.1 Choosing a setup location 14

4.2.2 Rack precautions 14

4.2.3 General system precautions 15

4.2.4 Rack mounting considerations 15

4.3 Rack mounting instructions 16

4.3.1 Identifying the sections of the rack rails 16

4.3.2 Installing the inner rails 17

4.3.3 Assembling the outer rails 17

4.3.4 Installing the outer rails to the rack 18

4.3.5 Installing the chassis into the rack 19

4.3.6 Installing the chassis into a Telco rack 20

4.4 Turning on the system 20

5.1 Introduction 21

5.2 Setup instruction 21

5.3 Starting the application 21

5.4 Using Bosch VMS Config Wizard 22

5.5 Adding additional licenses 23

5.6 Using Bosch VMS Operator Client 23

6.1 Adding new drives to Windows Server 25

6.2 Creating a VHD iSCSI target for VRM 25

6.3 Adding and formatting the VHD as a VRM target 26

Safety precautions 5

System overview 9

Inserting hard disks 13

Rack installation 14

System setup - first steps 21

Installing additional drives 25

Bosch Sicherheitssysteme GmbH Installation Manual 2014.12 | V3 | DOC

4 en | Table of Contents DIVAR IP 7000 1U

Connecting to the internet 27

7.1 Protecting the system from unauthorized access 27

7.2 Setting up port forwarding 27

7.3 Choosing an appropriate client 27

7.3.1 Remote connection with Operator Client 27

7.3.2 Remote connection with Video Security App 27

7.4 Installing an Enterprise Management Server 28

Recovering the unit 29

Additional documentation and client software 30

Appendices 31

10.1 Motherboard 31

10.1.1 Motherboard layout 31

10.1.2 Motherboard component overview 32

10.1.3 Motherboard features 34

10.1.4 Block diagram 36

10.2 Chipset overview 36

10.3 PC health monitoring 37

10.4 Power configuration settings 37

10.5 Power supply 38

10.6 Super I/O 38

10.7 iSCSI support 38

10.8 Overview of the Nuvoton BMC controller 39

2014.12 | V3 | DOC Installation Manual Bosch Sicherheitssysteme GmbH

DIVAR IP 7000 1U Safety precautions | en 5

1.1

Safety precautions

Observe the safety precautions in this chapter.

General safety precautions

Follow these rules to ensure general safety: – Keep the area around the system clean and free of clutter. – Place the chassis top cover and any system components that have been removed away

from the system or on a table so that they won't accidentally be stepped on.

– While working on the system, do not wear loose clothing such as neckties and

unbuttoned shirt sleeves, which can come into contact with electrical circuits or be pulled into a cooling fan.

– Remove any jewelry or metal objects from your body, which are excellent metal

conductors that can create short circuits and harm you if they come into contact with printed circuit boards or areas where power is present.

– After accessing the inside of the system, close the system back up and secure it to the

rack unit after ensuring that all connections have been made.

– The system is heavy when fully loaded. When lifting the system, two people at either end

should lift slowly with their feet spread out to distribute the weight. Always keep your back straight and lift with your legs.

Warning!

Interruption of mains supply:

Voltage is applied as soon as the mains plug is inserted into the mains socket.

However, for devices with a mains switch, the device is only ready for operation when the

mains switch (ON/OFF) is in the ON position. When the mains plug is pulled out of the

socket, the supply of power to the device is completely interrupted.

Warning!

Removing the housing:

To avoid electric shock, the housing must only be removed by qualified service personnel.

Before removing the housing, the plug must always be removed from the mains socket and

remain disconnected while the housing is removed. Servicing must only be carried out by

qualified service personnel. The user must not carry out any repairs.

Warning!

Power cable and AC adapter:

When installing the product, use the provided or designated connection cables, power cables

and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fire.

Electrical Appliance and Material Safety Law prohibits the use of UL or CSA-certified cables

(that have UL/CSA shown on the code) for any other electrical devices.

Bosch Sicherheitssysteme GmbH Installation Manual 2014.12 | V3 | DOC

6 en | Safety precautions DIVAR IP 7000 1U

Warning!

Lithium battery:

Batteries that have been inserted wrongly can cause an explosion. Always replace empty

batteries with batteries of the same type or a similar type recommended by the manufacturer.

Handle used batteries carefully. Do not damage the battery in any way. A damaged battery

may release hazardous materials into the environment.

Dispose of empty batteries according to the manufacturer's instructions.

Warning!

Handling of lead solder materials used in this product may expose you to lead, a chemical

known to the State of California to cause birth defects and other reproductive harm.

Notice!

Electrostatically sensitive device:

To avoid electrostatic discharges, the CMOS/MOSFET protection measures must be carried

out correctly.

When handling electrostatically sensitive printed circuits, grounded anti-static wrist bands

must be worn and the ESD safety precautions observed.

1.2

Notice!

Installation should only be carried out by qualified customer service personnel in accordance

with the applicable electrical regulations.

Disposal

Your Bosch product has been developed and manufactured using highquality materials and components that can be reused. This symbol means that electronic and electrical devices that have reached the end of their working life must be disposed of separately from household waste. In the EU, separate collecting systems are already in place for used electrical and electronic products. Please dispose of these devices at your local communal waste collection point or at a recycling center.

Electrical safety precautions

Basic electrical safety precautions should be followed to protect you from harm and the system from damage: – Be aware of the locations of the power on/off switch on the chassis as well as the room's

emergency power-off switch, disconnection switch or electrical outlet. If an electrical

accident occurs, you can then quickly remove power from the system. – Do not work alone when working with high voltage components. – Power should always be disconnected from the system when removing or installing main

system components, such as the motherboard or memory modules. When disconnecting

power, you should first turn off the system and then unplug the power cords from all the

power supply modules in the system. – When working around exposed electrical circuits, another person who is familiar with the

power-off controls should be nearby to switch off the power if necessary.

2014.12 | V3 | DOC Installation Manual Bosch Sicherheitssysteme GmbH

DIVAR IP 7000 1U Safety precautions | en 7

– Use only one hand when working with powered-on electrical equipment. This is to avoid

making a complete circuit, which will cause electrical shock. Use extreme caution when using metal tools, which can easily damage any electrical components or circuit boards they come into contact with.

– The power supply power cords must include a grounding plug and must be plugged into

grounded electrical outlets. The unit has more than one power supply cord. Disconnect both power supply cords before servicing to avoid electrical shock.

– Mainboard replaceable soldered-in fuses: Self-resetting PTC (Positive Temperature

Coefficient) fuses on the mainboard must be replaced by trained service technicians only. The new fuse must be the same or equivalent as the one replaced. Contact technical support for details and support.

Caution!

Mainboard Battery: There is a danger of explosion if the onboard battery is installed upside

down, which will reverse its polarities. This battery must be replaced only with the same or

an equivalent type recommended by the manufacturer (CR2032). Dispose of used batteries

according to the manufacturer's instructions.

Caution!

DVD-ROM Laser: This system comes without a DVD-ROM drive but if added: To prevent direct

exposure to the laser beam and hazardous radiation exposure, do not open the enclosure or

use the unit in any unconventional way.

1.3

ESD precautions

Electrostatic Discharge (ESD) is generated by two objects with different electrical charges coming into contact with each other. An electrical discharge is created to neutralize this difference, which can damage electronic components and printed circuit boards. The following measures are generally sufficient to neutralize this difference before contact is made to protect your equipment from ESD: – Do not use mats designed to decrease electrostatic discharge as protection from

electrical shock. Instead, use rubber mats that have been specifically designed as

electrical insulators. – Use a grounded wrist strap designed to prevent static discharge. – Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready

for use. – Touch a grounded metal object before removing the board from the antistatic bag. – Do not let components or printed circuit boards come into contact with your clothing,

which may retain a charge even if you are wearing a wrist strap. – Handle a board by its edges only. Do not touch its components, peripheral chips, memory

modules or contacts. – When handling chips or modules, avoid touching their pins. – Put the mainboard and peripherals back into their antistatic bags when not in use. – For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and the

mainboard.

1.4

Bosch Sicherheitssysteme GmbH Installation Manual 2014.12 | V3 | DOC

Operating precautions

The chassis cover must be in place when the system is operating to assure proper cooling. Out of warranty damage to the system can occur if this practice is not strictly followed.

8 en | Safety precautions DIVAR IP 7000 1U

Note:

Please handle used batteries carefully. Do not damage the battery in any way. A damaged battery may release hazardous materials into the environment. Do not discard a used battery in the garbage or a public landfill. Please comply with the regulations set up by your local hazardous waste management agency to dispose of your used battery properly.

1.5

1.6

Important notices

Accessories - Do not place this unit on an unstable stand, tripod, bracket,

or mount. The unit may fall, causing serious injury and/or serious damage to the unit. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer. When a cart is used, use caution and care when moving the cart/apparatus combination to avoid injury from tip-over. Quick stops, excessive force, or uneven surfaces may cause the cart/unit combination to overturn. Mount the unit per the manufacturer's instructions.

FCC and ICES compliance

(only for U.S.A. and Canada) This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense.

2014.12 | V3 | DOC Installation Manual Bosch Sicherheitssysteme GmbH

DIVAR IP 7000 1U System overview | en 9

System overview

DIVAR IP 7000 1U is an affordable, simple and reliable all-in-one recording, viewing and management solution for network surveillance systems of up to 64 channels (with 32 channels pre-licensed). Running the full Bosch VMS (Video Management System) solution and powered by Bosch VRM (Video Recording Manager) software, the DIVAR IP 7000 1U is an intelligent IP storage device that eliminates the need for separate NVR (Network Video Recorder) server and storage hardware. The 1U unit combines advanced management and state-of-the-art recording management into a single cost-effective, plug and play IP recording appliance for IT-minded customers which are seeking for a state-of-the-art “second generation” NVR recording solution. DIVAR IP 7000 1U features: – Instant real time access to video

View high quality HD video despite low or limited bandwidth connections. Dynamic

Transcoding technology ensures that you can view your video immediately — anytime,

anywhere. – Easy installation

DIVAR IP 7000 1U features wizard based set-up and centralized configuration to reduce

installation times. All components are pre-installed and pre-configured. Simply connect to

the network and turn on the unit — DIVAR IP 7000 1U starts recording straight out of the

box. – Access to Bosch VMS

After starting the system, immediate access to the Bosch VMS management application is

offered by a customized user interface. The ability to use one central user interface for

configuration and operation management reduces installation and training requirements,

and helps to keep ongoing system management costs low.

2.1

2.2

2.2.1

Chassis features

The chassis includes the following features: – 4 slots for 4 SATA drives – Graphic card (1x DVI, 1x Display Port output) – One slim DVD-RW drive. This drive allows you to quickly install or save data. – One internal USB Transcoder device – Other onboard features are included to promote system health. These include various

cooling fans, a convenient power switch and a reset button.

Chassis components

This chapter describes the most common components included with your chassis. For more information, see the installation instructions detailed later in this manual.

Chassis

The chassis includes 4 hard drive bays and supports a 1U backplane, fans and two power supplies.

Bosch Sicherheitssysteme GmbH Installation Manual 2014.12 | V3 | DOC

10 en | System overview DIVAR IP 7000 1U

2.2.2

2.2.3

2.2.4

2.2.5

2.2.6

Backplane

Each chassis comes with a 1U backplane. The backplane accepts SAS/SATA hard drives.

Warning!

Use caution when servicing and working around the backplane. Hazardous voltage or energy

is present on the backplane when the system is operating. Do not touch the backplane with

any metal objects and make sure no ribbon cables touch the backplane.

Fans

The chassis supports system fans that are 1U high and powered from the motherboard.

Mounting rails

The unit can be placed in a rack for secure storage and use. To setup your rack, follow the step-by-step instructions included in this manual.

Power supply

Each chassis model includes 2 high-efficiency power supplies (redundant). In the unlikely event your power supply fails, replacement is simple and can be accomplished without tools.

Air shroud

Air shrouds are shields, usually plastic, which conduct the airflow directly to where it is needed. Always use the air shroud included with your chassis.

2.3

System interface

There are several LEDs on the front and rear of the chassis. The LEDs show the over-all status of the system and the activity and health of specific components.

Front view:

1 2x USB 2.0 5 Power

2 Failure information (not used) 6 Reset

3 NIC1/NIC2 7 Power on/off

4 HDD

2014.12 | V3 | DOC Installation Manual Bosch Sicherheitssysteme GmbH

DIVAR IP 7000 1U System overview | en 11

Rear view:

2.3.1

1 2x mains connection 100 – 240 VAC,

50 - 60 Hz

Note: Connect both power cables.

2 2x PS/2 (mouse and keyboard) 6 2x NIC

3 2x USB 2.0 7 1x graphic card (1x Display Port,

4 Serial interface COM

5 Monitor (VGA)

Note: Do not use!

Note: Connect both NIC ports to the

appropriate network switch.

1x DVI) Note: DVI port must be used for configuration.

Control panel buttons

There are two push-buttons located on the front of the chassis. These are (in order from left to right) a reset button and a power on/off button.

–

supply to the server system. Turning off system power with this button removes the main

power but keeps standby power supplied to the system. Therefore, you must unplug

system before servicing.

Reset: The reset button is used to reboot the system.

Power: The main power switch is used to apply or remove power from the power

2.3.2

Bosch Sicherheitssysteme GmbH Installation Manual 2014.12 | V3 | DOC

Control panel LEDs

The control panel located on the front of the chassis has LEDs to provide you with critical information related to different parts of the system. This section explains what each LED indicates.

– Information LED: not used

– NiC2: A flashing LED indicates network activity on GLAN2.

– NIC1: A flashing LED indicates network activity on GLAN1.

12 en | System overview DIVAR IP 7000 1U

– HDD: A flashing LED indicates IDE channel activity in the SAS/SATA drive, SCSI

drive, and/or DVD-ROM drive activity.

2.3.3

–

This LED should normally be illuminated when the system is operating.

Power: Indicates power is being supplied to the system's power supply units.

Power supply LEDs and overheat indicators

This chassis provides several options which may include hot-swappable, cold-swappable, and redundant power supplies. Some power supplies include an LED in the rear with the following definitions:

Power supply LEDs

Solid green Power supply is on.

Solid amber The power supply is plugged in and turned off, or the

system is off but in an abnormal state.

2014.12 | V3 | DOC Installation Manual Bosch Sicherheitssysteme GmbH

DIVAR IP 7000 1U Inserting hard disks | en 13

Inserting hard disks

This chapter describes the insertion of hard disks that are mounted in drive carriers to simplify their installation.

To insert the drive carrier:

4 Insert the drive carrier into the chassis bay. Make sure that the drive carrier handle is

completely closed.

Notice!

We recommend using the respective Bosch hard disk drives. The hard disk drives as one of

the critical component are carefully selected by Bosch based on available failure rates. HDD –

not delivered from Bosch – are not supported. Information on supported HDDs can be found

in the datasheet in the Bosch Online Product Catalog.

Bosch DIP-7040-00N Installation Manual

Table of contents

Safety precautions

General safety precautions

Electrical safety precautions

ESD precautions

Operating precautions

Important notices

FCC and ICES compliance

System overview

Chassis features

Chassis components

Chassis

Backplane

Fans

Mounting rails

Power supply

Air shroud

System interface

Control panel buttons

Control panel LEDs

Power supply LEDs and overheat indicators

Inserting hard disks