Bosch B22FT80SNS/01 Owner’s Manual

en Operating instructions fr Notice d'utilisation

Dg(_lateur combin@

THANKYOUforpurchasingthishigh-qualityproductfromBOSCH.Ifyoushouldexperienceaproblemnotcoveredin TROUBLESHOOTING,pleasevisitourwebsiteatwww.bosch-home.com/usforadditionalinformation.Ifyoustillneedassistance,

callusat1-800-944-2904. InCanada,visitourwebsiteatwww.bosch-home.caorcallusat1-800-944-2904.

TableofContents/Tabledes rnati@res

REFRIGERATOR SAFETY ..................................................................... 2

Proper Disposal of Your Old Refrigerator ........................................... 3

INSTALLATION INSTRUCTIONS ......................................................... 3

Unpack the Refrigerator ...................................................................... 3

Location Requirements ....................................................................... 4

Electrical Requirements ...................................................................... 4

Water Supply Requirements ............................................................... 5

Connect the Water Supply .................................................................. 5

Refrigerator Door(s) and Drawer ......................................................... 7

Door Closing and Door Alignment ...................................................... 9

REFRIGERATOR USE ........................................................................... 9

Opening and Closing Doors ................................................................ 9

Using the Controls ............................................................................ 10

Crisper Humidity Control .................................................................. 11

Ice Maker ........................................................................................... 11

Water Dispenser ................................................................................ 12

Water Filtration System ..................................................................... 12

REFRIGERATOR CARE ....................................................................... 13

Cleaning ............................................................................................ 13

Changing the Light Bulb ................................................................... 13

Vacation and Moving Care ............................................................... 13

TROUBLESHOOTING .......................................................................... 14

Refrigerator Operation ...................................................................... 14

Temperature and Moisture ............................................................... 15

Ice and Water .................................................................................... 15

Assistance or Service ........................................................................ 16

WATER FILTER CERTIFICATIONS .................................................... 16

PERFORMANCE DATA SHEETS ........................................................ 17

STATEMENT OF LIMITED WARRANTY ............................................ 19

SI_CURITI_ DU RI_FRIGI_RATEUR ..................................................... 20

Mise au rebut adequate de votre vieux refrigerateur ....................... 21

INSTRUCTIONS D'INSTALLATION ................................................... 21

Deballage du refrigerateur ................................................................ 21

Exigences d'emplacement ............................................................... 22

Specifications electriques ................................................................. 22

Specifications de I'alimentation en eau ............................................ 22

Raccordement de la canalisation d'eau ........................................... 23

Porte(s) et tiroir du refrigerateur ........................................................ 24

Fermeture et alignement de la porte ................................................ 27

UTILISATION DU RI_FRIGI_RATEUR ................................................. 27

Ouverture et fermeture des portes ................................................... 27

Utilisation des commandes .............................................................. 28

Reglage de I'humidite dans le bac & legumes ................................. 29

Machine & glagons ............................................................................ 30

Distributeur d'eau ............................................................................. 30

Systeme de filtration de I'eau ........................................................... 31

ENTRETIEN DU RI_FRIGI_RATEUR ................................................... 31

Nettoyage .......................................................................................... 31

Remplacement de I'ampoule d'eclairage ......................................... 32

Entretien avant les vacances ou Iors d'un demenagement ............. 32

DI_PANNAGE ........................................................................................ 33

Fonctionnement du refrig6rateur ...................................................... 33

Temperature et humidite .................................................................. 34

Glagons et eau .................................................................................. 34

Assistance ou Service ....................................................................... 35

FEUlLLES DE DONNI_ES SUR LA PERFORMANCE ........................ 36

GARANTIE ............................................................................................ 38

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline, away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

• Do not hit the refrigerator glass doors (on some models).

Proper DisposalofYourOld Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of your old refrigerator, please follow these instructions to help

prevent accidents.

Before YouThrow Away Your Old Refrigerator or Freezer:

• Takeoffthe doors.

• Leave the shelves in place so that children may not easily climb inside.

important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water

and dry. Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

WhenMoving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

W' (1.25cm)

Clean Before Using

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in "Refrigerator Care."

important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Loc<:Y 7!!equ emen,$s

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor, household use only.

To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) of space on each side and at the top. Allow for 1" (2.54 cm) of space behind the refrigerator. If your refrigerator has an ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall, leave 21/2'' (6.3 cm) minimum on the hinge side (some models require more) to allow for the door to swing open.

NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum

of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

][

2Y2(63 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method A 115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation or cleaning, or removing a light bulb, turn cooling off or turn the control

(Thermostat, Refrigerator or Freezer Control depending on the model) to OFF, and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and turn cooling on or reset the

control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting. See "Using the Controls" in the User Instructions, User Guide, or Use & Care Guide.

Gathertherequiredtoolsandpartsbeforestartinginstallation. Readandfollowtheinstructionsprovidedwithanytoolslisted

here.

TOOLS NEEDED:

• Flat-blade screwdriver • Y4"Nut driver

• 7/le"and Y2"Open-end or two • Y4"Drill bit adjustable wrenches

IM PORTANT:

• All installations must meet local plumbing code requirements.

• Do not use a piercing-type or 3/_e"(4.76 mm) saddle valve which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain

above freezing.

• For models with water filters, the disposable water filter should be replaced at least every 6 months.

Water Pressure

A cold water supply with water pressure of between 35 and 120 psi (241 and 827 kPa) is required to operate the water dispenser and ice maker. Ifyou have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and

827 kPa). If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration System."

If you have questions about your water pressure, call a licensed, qualified plumber.

Read all directions before you begin.

IM PORTANT:

• Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and

ordinances. The gray water tubing on the back of the refrigerator (which is

used to connect to the household water line) is a PEX (cross-linked polyethylene) tube. Copper and PEX tubing connections from the household water line to the refrigerator are acceptable, and will help avoid off-taste or odor in your ice or water. Check for leaks.

If PEXtubing is used instead of copper, please call us at 1-800-944-2904 for assistance.

• Cordless drill

Install tubing only in areas where temperatures will remain above freezing.

If you turn on the refrigerator before the water line is connected, turn off the ice maker to avoid excessive noise or

damage to the water valve.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Find a Y2"to 11/4'' (12.7 mm to 31.8 mm) vertical cold water pipe near the refrigerator.

IMPO RTANT:

• Make sure it is a cold water pipe.

Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from the connection on the lower right rear of the refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use

Y4"(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a Y4"hole in the cold water pipe you have selected.

D E

F G

A. Cold water pipe B. Pipe clamp

C. Copper tubing D. Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the Y4"drilled hole in

the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not

overtighten.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as itwill go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten or

you may crush the copper tubing.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe.

E.Compression sleeve F. Shutoff valve

G.Packing nut

Connect to Refrigerator

Depending on your model, the water line may come down from the top or up from the bottom. Follow the connection instructions

for your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the copper tube to the valve inlet using a compression nut and

sleeve as shown. Tighten the compression nut. Do not overtighten. Confirm copper tubing is secure by pulling on copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a "P" clamp.

Using an adjustable wrench, hold the nut on the plastic water line to keep it from moving. Then, with a second wrench turn

the compression nut on the copper tubing counterclockwise to completely tighten. Do not overtighten.

..........C

..........D

A. "P" clamp B. Plastic water fine

C. Compression nut D. Copper tubing

A. Copper tubing B. "P" clamp

C. Compression nut D. Compression sleeve

3. Turn on water supply to refrigerator and check for leaks. Correct any leaks.

Style 2

1. Create a service loop (minimum diameter of 2 ft [61 cm]) with the copper tubing. Avoid kinks when coiling the copper tubing.

2. Remove the plastic cap from water valve inlet port. Place a compression nut and sleeve on the copper tubing.

3. Insert the end of the copper tubing into the water valve inlet port. Shape tubing slightly so that the tubing feeds straight

into the port to avoid kinks.

4. Slide the compression nut over the sleeve and screw into the water valve inlet port.

6. Check connection by pulling on copper tubing. Attach the plastic water line to the refrigerator cabinet with a "P" clamp.

7. Turn on water supply to the refrigerator and check for leaks. Correct any leaks.

Complete the Installation

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet. NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely fill the ice storage bin.

f ..........

.........O

A. Plastic water tubing C. Compression nut B. Sleeve D. Copper tubing

All graphics referenced in the following instructions are included 3. Align the door so that the bottom of the refrigerator door later in this section after "Final Steps." aligns evenly with the top of the freezer drawer. Tighten all

TOOLS NEEDED: %6", %", ¼" hex head socket wrenches, screws. #2 Phillips screwdriver, and a fiat-blade screwdriver. 4. Reconnect the wiring plug on top of the left-hand side

refrigerator door.

Remove and Replace Handles 5. Replace the top hinge covers.

1. Using a 3/32"hex key, loosen the two setscrews located on the side of each handle. See graphics 1 and 2.

2. Pull the handle straight out from the door. Make sure you keep the screws for reattaching the handles.

3. To replace the handles, reverse the directions.

Remove Doors and Hinges

IMPORTANT: Remove food and any adjustable door or utility bins from doors.

Electrical Shock Hazard

Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are working.

Starting with the right-hand side door, remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door from the bottom hinge pin.

NOTE: On some models, remove the shim from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

Before removing the left-hand side door, disconnect the wiring plug located on top of the top hinge by wedging a flat-blade screwdriver or your fingernail between the two sections. See

Wiring Plug graphic. NOTE: The green, ground wire remains attached to the hinge.

Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the left-hand side door from the bottom hinge pin.

NOTE: On some models, remove the shim from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

Replace Doors and Hinges

Assemble the parts for the top hinge as shown in Top Hinge graphic. Do not tighten the screws completely.

Replace the parts for the bottom hinge as shown in Bottom Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door while the hinges are being moved. Do not depend on the door

gasket magnets to hold the door in place while you are working.

Remove and Replace Freezer Drawer Front

IMPORTANT: Two people may be required to remove and replace the freezer drawer front. Graphics are included later in this

section.

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to position the two screws in the bottom of the drawer front into the brackets.

See Drawer Front Replacement graphic.

3. Completely tighten the four screws.

Final Steps

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Return all removable door parts to doors and food to refrigerator.

Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

Top Hinges

A, Hinge Cover Screw

B, Top Hinge Cover C, 5/18"Hex Head Hinge Screws

D, Top Hinge

Bottom Hinges

Electrical Shock Hazard

A. Shim (on some models)

B, Bottom Hinge C. Hinge Screws

Wiring Plug

A. 3/32"Setscrew

A, 3/32"Setscrew

A, Loosen 4 Door Bracket Screws

The base grille covers the leveling screws and roller assemblies located at the bottom of the refrigerator cabinet below the freezer door or drawer. Before making adjustments, remove the base

grille and move the refrigerator to its final location.

1. Remove the two screws fastening the base grille to the cabinet, and set the screws aside. Grasp the grille and pull it toward you.

Move the refrigerator to its final location. NOTE: To allow the refrigerator to roll easier, raise the leveling

legs off the floor by turning the leveling screws counterclockwise. The front rollers will be touching the floor.

So the doors will close easier, use a Y4"hex driver to turn both leveling screws clockwise. This will raise the front of the

refrigerator tilting it slightly downward to the rear. Turn both leveling screws the same amount.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws. This

makes it easier to turn the screws.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws. This

makes it easier to turn the screws.

6. Make sure the refrigerator is steady. If the refrigerator seems unsteady or rolls forward when the door or drawer is opened

adjust the leveling screws. Using a 1/4"hex driver, turn the leveling screw on each side clockwise until the rollers are up and the leveling feet are firmly against the floor.

7. Replace the base grille by aligning the holes in the grille with the holes in the cabinet and fasten using the screws removed

in Step 1.

A. Leveling screw

B. Front roller

Open and close the doors to make sure they close as easily as you like. If not, increase the tilt by turning both leveling screws

clockwise. It may take several turns of the leveling screw to allow the doors to close easier.

Check for door alignment. If one door is lower than the other, adjust the leveling screw, on the lower side of the refrigerator.

Using a 1/4"hex driver, turn the screw clockwise to raise that side of the refrigerator until the doors are aligned. It may take several turns of the leveling screw to raise the refrigerator.

REFRIGERATORUSE

There are two refrigerator compartment doors. The doors can be opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically forms a seal between the two doors.

A. Hinged seal

The control center is located at the top front of the refrigerator compartment.

Temperature Controls

For your convenience, your temperature controls are preset at the factory. When you first install your refrigerator, make sure the controls are still set to the recommended set points as shown.

Recommended Settings

0" recommended 38 ° recommended

38 ° recommended

refrigerator

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR Control

1° lower

freezer refrigerator

IM PORTANT:

The recommended settings should be correct for normal household refrigerator use. The controls are set correctly

when milk or juice is as cold as you like and when ice cream is firm.

When the power is on, the temperature display shows the set point temperature of the compartment.

Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature controls to a colder than recommended setting will not cool the compartments any faster.

If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

To Turn Your Refrigerator Off/On:

• Press the freezer (+) touch pad repeatedly until "OFF" appears in the freezer display. Allow a few seconds for the refrigerator

to shut off. Neither compartment will cool.

• Press either the refrigerator or freezer (-) touch pad to turn on the refrigerator.

Adjusting Controls

The REFRIGERATOR control adjusts the refrigerator compartment temperature. The FREEZER control adjusts the freezer

compartment temperature. If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart as a guide.

FREEZER too warm/too little ice Adjust FREEZER

Control 1° lower

REFRIGERATOR too cold Adjust REFRIGERATOR

Control 1° higher

FREEZER too cold Adjust FREEZER

Control 1° higher

Additional Control Center Features

Max Ice

The Max Ice feature assists with temporary periods of heavy ice use by increasing ice production.

• Press the Max Ice feature touch pad to set the freezer to the lowest temperature setting. Press the Max Ice feature touch pad again to return to the normal freezer set point.

NOTE: The Max Ice feature will automatically shut off in approximately 24 hours.

Max

Ice

Humidity Control

The Humidity Control feature turns on a heater to help reduce moisture on the door hinge seal. Use in humid environments or

when you notice moisture on the door hinge seal. The refrigerator uses more energy when Humidity Control is on.

• Press Humidity Control when the environment is warm and more humid, or if you notice moisture on the door hinge seal.

The indicator light will be lit when humidity control is ON.

• Press Humidity Control to save energy when the environment is less humid.

To Adjust Set Point Temperatures: The first touch of the (+) or (-) touch pad displays the current

temperature set point.

• Press the (+) or (-) touch pads until the desired temperature set point is displayed.

NOTE: Except when first turning on the refrigerator, do not adjust either temperature control more than one setting at a time. Wait 24 hours between adjustments for the temperature to stabilize.

Humidity

Control

press if moisture

appears

Temp Alarm

The Temp Alarm feature provides temperature information in the event of a power outage.

Power outage: During a power outage, if the temperatures in the refrigerator and freezer compartments exceed normal operating temperatures, the highest temperature reached will be displayed.

• Press the Temp Alarm touch pad until the indicator light is lit, to turn on this feature. Press and hold Temp Alarm for

3 seconds until the indicator light goes off to turn off this feature.

Temperature alarm: An alarm will sound repeatedly if the freezer or refrigerator compartment temperatures exceed normal

operating temperatures for an hour or more. The temperature displays will alternately show the current

temperatures and the highest temperatures the compartments reached.

Press the Temp Alarm touch pad once to stop the audible alarm and alternating temperature displays. The Temp Alarm light will continue to flash until the refrigerator returns to the

set temperature.

Temp Alarm

Door Alarm The Door Alarm feature sounds a chime every few seconds when

the refrigerator door has been left open for 5 continuous minutes. The chime will sound until the door is closed or Door Alarm is

turned off.

• Press the Door Alarm touch pad to turn this feature on or off. The indicator light will be lit when the Door Alarm feature is on.

Door

Alarm

Super

The Super feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm room temperatures.

• Press Super to set the freezer and refrigerator to the lowest temperature settings. Press Super again to return to the

normal refrigerator set point. NOTE: The Super feature will automatically shut off in

approximately 12 hours.

Super

Alarm (AL)

This preference allows you to turn off the sound of all alarms. ON - You will hear the alarm sound.

OFF - You will not hear the alarm sound.

To Access the User Preferences Menu:

1. Press and hold the Door Alarm touch pad for 3 seconds. The preference name will appear in the Freezer display and the preference status (For C) or (ON or OFF) will appear in the

Refrigerator display.

2. Use the Freezer (+) or (-) touch pads to scroll through the preference names. When the desired preference name is

displayed, press the Refrigerator (+) or (-) touch pads to change the preference status.

3. Set your preferences by pressing and holding the Door Alarm touch pad for 3 seconds, or by shutting the refrigerator compartment door.

You can controltheamount ofhumidityinthe moisture-sealed crisper.Depending on your model,adjustthe controltoany

settingbetween FRUIT and VEGETABLES or LOW and HIGH.

FRUIT/LOW (open) for best storage of fruits and vegetables with skins.

VEGETABLES/HIGH (closed) for best storage of fresh, leafy vegetables.

ce M< £e

IMPORTANT: Flush the water system before turning on the ice maker. See "Water Dispenser."

Turning the Ice Maker On/Off

Toturn the ice maker ON, simply lower the wire shutoff arm. To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click. NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position. Do not force the wire shutoff arm up or down.

Filter Reset

The Filter Reset control allows you to restart the water filter status tracking feature each time you replace your water filter. See

"Water Filtration System."

• Press and hold the Filter Reset touch pad for 3 seconds, until the Order or Replace light turns off.

I I

order replace

Filter

Reset

press 3 sec

User Preferences

The control center allows you to set user preferences, if desired. Temperature Display (F_C) This preference allows you to change the temperature display. F - Temperature in degrees Fahrenheit C - Temperature in degrees Celsius

NOTE: Turn off the ice maker before removing the ice storage bin to serve ice or to clean the bin. This will keep the ice cubes from

dropping out of the ice maker and into the freezer compartment. After replacing the ice storage bin, turn on the ice maker.

Ice Production Rate

• The ice maker should produce a complete batch of ice approximately every 3 hours.

• To increase ice production, lower the freezer and refrigerator temperature. See "Using the Controls." Wait 24 hours between adjustments.

Remember

Allow 24 hours to produce the first batch of ice. Allow 3 days to completely fill the ice storage bin. Discard the first three batches of ice produced.

The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to

poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well

maintained. Do not store anything on top of the ice maker or in the ice

storage bin.

IM PORTANI"."

After connecting the refrigerator to awater source or replacing the water filter, flush the water system. Use a sturdy container to depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to

flow. Once water begins to flow, continue depressing and releasing the dispenser lever (5 seconds on, 5 seconds off) until a total of 4 gal. (15 L) has been dispensed. This will flush air from the filter and water dispensing system, and prepare

the water filter for use. Additional flushing may be required in some households. As air is cleared from the system, water may spurt out of the dispenser.

NOTE: After 5 minutes of continuous dispensing, the dispenser will stop dispensing water to avoid flooding. To

continue dispensing, press the dispenser button again.

• Allow 24 hours for the refrigerator to cool down and chill water. Dispense enough water every week to maintain a fresh

supply.

Dispensing Water

1. Hold a container under the dispenser while pressing the button.

2. Release the button to stop dispensing.

tes F on

The water filter is located in the upper right-hand corner of the refrigerator compartment.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain

filterable cysts.

Water Filter Status Lights

The water filter status lights will help you know when to change the water filter. When the Order light is on, it is almost time to change the water filter. When the Replace light is on, a new water

filter should be installed. After replacing the water filter, press and hold FILTER RESET for

3 seconds until the Order or Replace light turns off. See "Using the Controls."

IMPORTANT: The disposable water filter should be replaced at least every 6 months. If the water flow to the water dispenser or

ice maker decreases noticeably before 6 months have passed, replace the water filter more often.

Replacing the Water Filter

To purchase a replacement water filter, contact your dealer or call 1-800-944-2904.

IMPORTANT: Air trapped in the water system may cause water and filter to eject. Always dispense water for at least 2 minutes before removing the filter or blue bypass cap.

1. Turn filter counterclockwise to remove.

2. Remove sealing label from replacement filter and insert the filter end into the filter head.

Turn the filter clockwise until it stops. Snap the filter cover closed.

Flush the water system. See "Water Dispenser" or "Water and Ice Dispenser."

NOTE: The dispenser feature may be used without a water filter installed. Your water will not be filtered. If this option is chosen, replace the filter with the blue bypass cap.

+ 28 hidden pages