Bosch B22CT80SNS/01, B22CT80SNP/01 Owner’s Manual

B22CT80SNS _ B T80SNP

F_f_ .

R_frio_roteur _ _noeloteur combine

_ __ _ _i;¸¸¸

en Operating instructions fr Notice d'utilisation

THANKYOUforpurchasingthishigh-qualityproductfromBOSCH.Ifyoushouldexperienceaproblemnotcoveredin TROUBLESHOOTING,pleasevisitourwebsiteatwww.bosch-home.com/usforadditionalinformation.Ifyoustillneedassistance,

callusat1-800-944-2904. InCanada,visitourwebsiteatwww.bosch-home.caorcallusat1-800-944-2904.

TableofContents/Tabledes rnati@res

REFRIGERATOR SAFETY ..................................................................... 2

Proper Disposal of Your Old Refrigerator ........................................... 3

INSTALLATION INSTRUCTIONS ......................................................... 3

Unpack the Refrigerator ...................................................................... 3

Location Requirements ....................................................................... 4

Electrical Requirements ...................................................................... 4

Water Supply Requirements ............................................................... 5

Connect the Water Supply .................................................................. 5

Refrigerator Door(s) and Drawer ......................................................... 7

Adjust the Doors ................................................................................. 9

REFRIGERATOR USE ........................................................................... 9

Opening and Closing Doors ................................................................ 9

Using the Controls .............................................................................. 9

Crisper Humidity Control .................................................................. 11

Ice Maker ........................................................................................... 11

Water Dispenser ................................................................................ 11

Water Filtration System ..................................................................... 12

REFRIGERATOR CARE ....................................................................... 12

Cleaning ............................................................................................ 12

Changing the Light Bulb ................................................................... 13

Vacation and Moving Care ............................................................... 13

TROUBLESHOOTING .......................................................................... 14

Refrigerator Operation ...................................................................... 14

Temperature and Moisture ............................................................... 14

Ice and Water .................................................................................... 15

Assistance or Service ........................................................................ 16

WATER FILTER CERTIFICATIONS .................................................... 16

PERFORMANCE DATA SHEETS ........................................................ 17

STATEMENT OF LIMITED WARRANTY ............................................ 19

SI_CURITI_ DU RI_FRIGI_RATEUR ..................................................... 20

Mise au rebut adequate de votre vieux refrigerateur ....................... 21

INSTRUCTIONS D'INSTALLATION ................................................... 21

Deballage du refrigerateur ................................................................ 21

Exigences d'emplacement ............................................................... 22

Specifications electriques ................................................................. 22

Specifications de I'alimentation en eau ............................................ 22

Raccordement de la canalisation d'eau ........................................... 23

Porte(s) et tiroir du refrigerateur ........................................................ 24

Ajustement des portes ...................................................................... 27

UTILISATION DU RI_FRIGI_RATEUR ................................................. 27

Ouverture et fermeture des portes ................................................... 27

Utilisation des commandes .............................................................. 27

Reglage de I'humidite dans le bac & legumes ................................. 29

Machine & glagons ............................................................................ 29

Distributeur d'eau ............................................................................. 30

Systeme de filtration de I'eau ........................................................... 30

ENTRETIEN DU RI_FRIGI_RATEUR ................................................... 30

Nettoyage .......................................................................................... 30

Remplacement de I'ampoule d'eclairage ......................................... 31

Entretien avant les vacances ou Iors d'un demenagement ............. 31

DI_PANNAGE ........................................................................................ 32

Fonctionnement du refrig6rateur ...................................................... 32

Temperature et humidite .................................................................. 33

Glagons et eau .................................................................................. 33

Assistance ou Service ....................................................................... 34

FEUlLLES DE DONNI_ES SUR LA PERFORMANCE ........................ 35

GARANTIE ............................................................................................ 37

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline, away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

• Do not hit the refrigerator glass doors (on some models).

Proper DisposalofYourOld Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Takeoffthe doors.

• Leave the shelves in place so that children may not easily climb inside.

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

WhenMoving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

W' (1.25cm)

Clean Before Using

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in "Refrigerator Care."

important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

Loc<x 7!!equ emen,$s

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator. Failure to do so can result in death, explosion, or fire.

IMPORTANT: This refrigerator is designed for indoor, household use only.

To ensure proper ventilation for your refrigerator, allow for 1/2" (1.25 cm) of space on each side and at the top. Allow for 1" (2.54 cm) of space behind the refrigerator. If your refrigerator has

an ice maker, allow extra space at the back for the water line connections. When installing your refrigerator next to a fixed wall, leave 21/2'' (6.3 cm) minimum on the hinge side (some models require more) to allow for the door to swing open.

NOTE: This refrigerator is intended for use in a location where the temperature ranges from a minimum of 55°F (13°C) to a maximum of 110°F (43°C). The preferred room temperature range for optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F (32°C). It is recommended that you do not install the refrigerator near a heat source, such as an oven or radiator.

][

2V2(63 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method A 115 volt, 60 Hz, AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, turn Cooling OFF, and then disconnect the refrigerator from the electrical source. When you have finished, reconnect the refrigerator to the electrical source and turn Cooling

ON. See "Using the Control(s)."

Gathertherequiredtoolsandpartsbeforestartinginstallation. Readandfollowtheinstructionsprovidedwithanytoolslisted

here.

TOOLS NEEDED:

• Flat-blade screwdriver • Y4" Nut driver

• 7/le" and Y2"Open-end or two • Y4"Drill bit adjustable wrenches

IM PORTANT:

• All installations must meet local plumbing code requirements.

• Do not use a piercing-type or 3/_e"(4.76 mm) saddle valve which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain

above freezing.

• For models with water filters, the disposable water filter should be replaced at least every 6 months.

• Cordless drill

Read all directions before you begin. IMPORTANT:

• Plumbing shall be installed in accordance with the International Plumbing Code and any local codes and

ordinances. The gray water tubing on the back of the refrigerator (which is

used to connect to the household water line) is a PEX (cross-linked polyethylene) tube. Copper and PEX tubing

connections from the household water line to the refrigerator are acceptable, and will help avoid off-taste or odor in your ice

or water. Check for leaks. If PEX tubing is used instead of copper, please call us at

1-800-944-2904 for assistance. Install tubing only in areas where temperatures will remain

above freezing. If you turn on the refrigerator before the water line is

connected, turn off the ice maker to avoid excessive noise or damage to the water valve.

Water Pressure

A cold water supply with water pressure of between 35 and 120 psi (241 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and

827 kPa). If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If your refrigerator has a water filter, it may further reduce the water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water Filtration System."

If you have questions about your water pressure, call a licensed, qualified plumber.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Find a Y2"to 11/4'' (12.7 mm to 31.8 mm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

Horizontal pipe will work, but the following procedure

must be followed: Drill on the top side of the pipe, not the

bottom. This will help keep water away from the drill. This

also keeps normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from the connection on the lower right rear of the refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use

Y4"(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a Y4"hole in the cold water pipe you have selected.

D E

F G

A. Cold water pipe B. Pipe clamp C. Copper tubing D. Compression nut

E. Compression sleeve F. Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4"drilled hole in

the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so the washer makes a watertight seal. Do not

overtighten.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten or

you may crush the copper tubing.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe.

Connect to Refrigerator

Depending on your model, the water line may come down from the top or up from the bottom. Follow the connection instructions for your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Confirm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks when coiling the copper tubing. Secure copper tubing to refrigerator cabinet with a "P" clamp.

Slide the compression nut over the sleeve and screw into the water valve inlet port.

...........C

........D

A. Plastic water tubing B. Sleeve

Using an adjustable wrench, hold the nut on the plastic water

C. Compression nut D. Copper tubing

line to keep it from moving. Then, with a second wrench turn the compression nut on the copper tubing counterclockwise

to completely tighten. Do not overtighten.

........ C

..........D

A. Copper tubing B. "P" clamp

C. Compression nut D. Compression sleeve

3. Turn on water supply to refrigerator and check for leaks. Correct any leaks.

Style 2

1. Create a service loop (minimum diameter of 2 ft [61 cm]) with the copper tubing. Avoid kinks when coiling the copper

tubing.

2. Remove the plastic cap from water valve inlet port. Place a compression nut and sleeve on the copper tubing.

3. Insert the end of the copper tubing into the water valve inlet port. Shape tubing slightly so that the tubing feeds straight into the port to avoid kinks.

A. "P" clamp B. Plastic water fine

C. Compression nut D. Copper tubing

6. Check connection by pulling on copper tubing. Attach the plastic water line to the refrigerator cabinet with a "P" clamp.

7. Turn on water supply to the refrigerator and check for leaks. Correct any leaks.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely

fill the ice storage bin.

All graphics referenced in the following instructions are included 3. Align the door so that the bottom of the refrigerator door later in this section after "Final Steps." aligns evenly with the top of the freezer drawer. Tighten all

TOOLS NEEDED: %6", 3/8",¼" hex head socket wrench, 3/32"or screws. V8"hex key, #2 Phillips screwdriver, and a fiat-blade screwdriver. 4. Reconnect the wiring plug on top of the left-hand side

refrigerator door.

Remove and Replace Handles 5. Replace the top hinge covers.

1. Using a3_32"or V8"hex key, loosen the two setscrews located on the side of each handle. See Graphics 1 and 2.

2. Pull the handle straight out from the door. Make sure you keep the screws for reattaching the handles.

3. To replace the handles, reverse the directions.

Remove Doors and Hinges

IMPORTANT: Remove food and any adjustable door or utility bins from doors.

Electrical Shock Hazard

Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the refrigerator door while the hinges are being removed. Do not depend on the door gasket magnets to hold the door in place while you are

working.

Starting with the right-hand side door, remove the parts for the top hinge as shown in Top Hinge graphic. Lift the refrigerator door from the bottom hinge pin.

NOTE: Remove the hinge pin cover from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

4. Before removing the left-hand side door, disconnect the wiring plug located on top of the top hinge by wedging a flat-blade

screwdriver or your fingernail between the two sections. See Wiring Plug graphic.

5. Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the left-hand side door from the bottom hinge pin.

NOTE: Remove the hinge pin cover from the bottom hinge pin and keep it for later use. See Bottom Hinge graphic.

Remove and Replace Freezer Drawer Front

IMPORTANT: Two people may be required to remove and replace the freezer drawer front. Graphics are included later in this

section.

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to position the two screws in the bottom of the drawer front into the brackets.

See Drawer Front Replacement graphic.

3. Completely tighten the four screws.

Final Steps

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Replace Doors and Hinges

Assemble the parts for the top hinge as shown in Top Hinge graphic. Do not tighten the screws completely.

Replace the parts for the bottom hinge as shown in Bottom Hinge graphic. Tighten screws. Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door while the hinges are being moved. Do not depend on the door

gasket magnets to hold the door in place while you are working.

1. Plug into a grounded 3 prong outlet.

2. Return all removable door parts to doors and food to refrigerator.

Disconnect power before removing doors. Failure to do so can result in death or electrical shock.

A, Hinge Cover Screw B, Top Hinge Cover

C, _6" Hex-Head Hinge Screws

D. Top Hinge

Bottom Hinges

Electrical Shock Hazard

A. Hinge Pin Cover

B, Bottom Hinge C. Hinge Screws

Wiring Plug

A. 3/32"Setscrew

A, 3/32"Setscrew

A, Loosen 4 Door Bracket Screws

IM PORTANI"."

Your refrigerator has two adjustable, front leveling screws - one on each side of the refrigerator base. If your refrigerator

seems unsteady or you want the door to close easier, use the instructions below.

Before moving the refrigerator, raise the leveling screws so the front rollers are touching the floor.

Remove the two screws fastening the base grille to the cabinet, and set the screws aside. Grasp the grille and pull it toward you.

2. Raise or lower the cabinet. Using a V4"hex driver, turn the leveling screw on each side to

raise or lower that side of the refrigerator. NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws. This makes it easier to turn the screws. It may take several turns of

the leveling screw to adjust the tilt of the refrigerator.

• To raise, turn the leveling screw clockwise.

• To lower, turn the leveling screw counterclockwise.

REFRIGERATORUSE

C_I'C ............. _d[JOO_S

There are two refrigerator compartment doors. The doors can be opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically forms a seal between the two doors.

A. Hinged seal

The control center is located at the top front of the refrigerator compartment.

Temperature Controls

A. Leveling screw B. Front roller

Open the door again to make sure that it closes as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws clockwise. It may take several more turns, and you should turn both screws the same

amount.

4. Replace the base grille.

For your convenience, your temperature controls are preset at the factory. When you first install your refrigerator, make sure the controls are still set to the recommended set points as shown.

Recommended Settings

0 °recommended 38° recommended

freezer refrigerator

IMPORTANT:

The recommended settings should be correct for normal household refrigerator use. The controls are set correctly when milk or juice is as cold as you like and when ice cream is

firm. When the power is on, the temperature display shows the

actual temperature of the compartment. Wait 24 hours for your refrigerator to cool completely before

adding food. If you add food before the refrigerator has cooled completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer temperature controls to a colder than recommended setting will not cool the compartments any faster.

If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.

On/Off:

• On/Offturnsoffcoolingforbothcompartments.Itdoesnot disconnectpowertotherefrigerator.

• PressandholdOn/Offfor3seconds.TheLEDwilllightupto indicatethatcoolingisOff.Pressthebuttonagaintoturnon thecooling.TheLEDwillturnoff.

• Press Humidity Control again to turn OFF and save energy when the environment is less humid.

Humidity

Control

press if moisture

appears

On/Off

press 3 sec

Adjusting Controls

The REFRIGERATOR control adjusts the refrigerator compartment temperature. The FREEZER control adjusts the freezer compartment temperature.

If you need to adjust the temperature in either the refrigerator or freezer compartment, use the settings listed in the chart as a

guide.

To Adjust Set Point Temperatures: The first touch of the (+) or (-) touch pad displays the current

temperature set point.

• Press the (+) or (-) touch pads until the desired temperature set point is displayed.

NOTE: Except when first turning on the refrigerator, do not adjust either temperature control more than one setting at a

time. Wait 24 hours between adjustments for the temperature to stabilize.

38 ° recommended

refrigerator

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm REFRIGERATOR Control

1° lower

Holiday

In holiday mode, the freezer switches to a timed defrost cycle that is not dependent on use. Interior lighting and dispensers are

disabled.

Press and hold the Holiday touch pad for 3 seconds or until the indicator light is lit to turn on this feature. Press and hold the Holiday touch pad again to turn off this feature. The

Holiday Icon will disappear, and the screen will display the settings as they were before Holiday was selected.

Holiday

press 3 sec

Alarm

The Alarm feature sounds a chime every few seconds when the refrigerator door has been left open for 5 continuous minutes. The

chime will sound until the door is closed or Alarm is turned off.

• Press the Alarm to turn this feature ON or OFR The indicator light will be lit when the Alarm feature is on.

Alarm

Super

The Super feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm room temperatures.

• Press SUPER to set the freezer and refrigerator to the lowest temperature settings. Press SUPER again to return to the

normal refrigerator set point. NOTE: The Super feature will automatically shut off in

approximately 12 hours.

FREEZER too warm/too little ice Adjust FREEZER

Control 1° lower

REFRIGERATOR too cold Adjust REFRIGERATOR

Control 1° higher

FREEZER too cold Adjust FREEZER

Control 1° higher

Additional Control Center Features

Humidity Control

The Humidity Control feature turns on a heater to help reduce moisture on the door hinge seal. Use in humid environments or

when you notice moisture on the door hinge seal. The refrigerator uses more energy when Humidity Control is on.

• Press Humidity Control when the environment is warm and more humid, or if you notice moisture on the door hinge seal.

The indicator light will be lit when humidity control is ON.

Super

Filter Reset

The Filter Reset control allows you to restart the water filter status tracking feature each time you replace your water filter. See

"Water Filtration System."

• Press and hold the Filter Reset touch pad for 3 seconds, until the Order or Replace light turns off.

m m

order replace

Filter

Reset

press 3 sec

User Preferences

Auto Ice Storage Bin

The control center allows you to set user preferences, if desired. Temperature Display (F_C)

This preference allows you to change the temperature display. F - Temperature in degrees Fahrenheit C - Temperature in degrees Celsius

Alarm (AL)

This preference allows you to turn off the sound of all alarms. ON - You will hear the alarm sound.

OFF - You will not hear the alarm sound.

To Access the User Preferences Menu:

1. Press and hold the Alarm touch pad for 3 seconds. The preference name will appear in the Freezer display and the

preference status (For C) or (ON or OFF) will appear in the Refrigerator display.

2. Use the Freezer (+) or (-) touch pads to scroll through the preference names. When the desired preference name is

displayed, press the Refrigerator (+) or (-) touch pads to change the preference status.

3. Set your preferences by pressing and holding the Alarm touch pad for 3 seconds, or by shutting the refrigerator

compartment door.

Jl _ ,_'._.x y _...._.01" _.J_

You can control the amount of humidity in the moisture-sealed crisper. Depending on your model, adjust the control to any

setting between FRUIT and VEGETABLES or LOW and HIGH. FRUIT/LOW (open) for best storage of fruits and vegetables with

skins. VEGETABLES/HIGH (closed) for best storage of fresh, leafy

vegetables.

ce M<xke

IMPORTANT: Flush the water system before turning on the ice maker. See "Water Dispenser."

Turning the Ice Maker On/Off

To turn the ice maker ON, simply lower the wire shutoff arm. To manually turn the ice maker OFF, lift the wire shutoff arm to the

OFF (arm up) position and listen for the click. NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position. Do not force the wire shutoff arm up or down.

Your ice storage bin has a lever which allows the storage bin to slide out with the drawer when it is pulled open or to stay in place.

• Move the lever to the right to attach the ice storage bin to the freezer drawer.

• Move the lever to the left to release the ice storage bin from the freezer drawer.

"// //H _, , = _ _ _ _ _

A. Ice storage bin lever

Ice Production Rate

The ice maker should produce a complete batch of ice approximately every 3 hours.

To increase ice production, lower the freezer and refrigerator temperature. See "Using the Controls." Wait 24 hours between adjustments.

Remember

Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced. Allow 3 days to completely

fill the ice storage bin. The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

Do not store anything on top of the ice maker or in the ice storage bin.

IMPORTANT:

After connecting the refrigerator to awater source or replacing the water filter, flush the water system. Use a sturdy container

to depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and

releasing the dispenser paddle (5 seconds on, 5 seconds off) until a total of 4 gal. (15 L) has been dispensed. This will flush air from the filter and water dispensing system, and prepare the water filter for use. Additional flushing may be required in

some households. As air is cleared from the system, water may spurt out of the dispenser.

NOTE: After 5 minutes of continuous dispensing, the dispenser will stop dispensing water to avoid flooding. To

continue dispensing, press the dispenser paddle again.

• Allow 24 hours for the refrigerator to cool down and chill water. Dispense enough water every week to maintain a fresh supply.

Dispensing Water

1. Hold a container under the dispenser spout while pressing the dispenser pad.

2. Release the dispenser pad to stop dispensing.

REFRIGERATORCARE

F System

The water filter is located in the upper right-hand corner of the refrigerator compartment.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

Water Filter Status Lights

The water filter status lights will help you know when to change the water filter. When the Order light is on, it is almost time to

change the water filter. When the Replace light is on, a new water filter should be installed.

After replacing the water filter, press and hold FILTER RESET for 3 seconds until the Order or Replace light turns off. See "Using

the Controls." IMPORTANT: The disposable water filter should be replaced at

least every 6 months. If the water flow to the water dispenser or ice maker decreases noticeably before 6 months have passed,

replace the water filter more often.

Replacing the Water Filter

To purchase a replacement water filter, contact your dealer or call 1-800-944-2904.

IMPORTANT: Air trapped inthe water system may cause water and filter to eject. Always dispense water for at least 2 minutes before removing the filter or blue bypass cap.

1. Turn filter counterclockwise to remove.

2. Remove sealing label from replacement filter and insert the filter end into the filter head.

Turn the filter clockwise until it stops. Snap the filter cover closed.

Flush the water system. See "Water Dispenser" or "Water and Ice Dispenser."

NOTE: The dispenser feature may be used without a water filter installed. Your water will not be filtered. If this option is chosen,

replace the filter with the blue bypass cap.

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately. IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm water.

• To keep your stainless steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested that you use the manufacturer's approved Stainless Steel

Conditioning Cloths. To order, call 1-800-944-2904. IMPORTANT: This cleaner isfor stainless steel parts only! Do not allow the Stainless Steel Conditioning Cloths to come

into contact with any plastic parts such as the trim pieces, dispenser covers or door gaskets. If unintentional contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth.

There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency. If you need to clean the condenser:

• Remove the base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

+ 28 hidden pages