BlueAnt Z9 User Manual
Contact BlueAnt:
Power ON Solid Blue for 5 Seconds
Power OFF Red flash 3 times
Pairing Mode Blue flashing
Reset Blue flashing
Charging Solid Red
Charging with Power ON
Solid Red with a Purple Flash
Charging Complete Red indicator OFF
Low Battery All LED’s change to Red
Idle Blue flash every 8 seconds
Standby 2 Blue flashes every 5 seconds
Ongoing call NO LED’s
Nth America
customercare@myblueant.com
1 866 891-3032
Australia
Australia
customercare@blueant.com.au
1300 669 049
New Zealand
New Zealand
customercare@blueant.com.au
0800 443 122
LED Indicator Chart
Z9i
QUICK START GUIDE
BLUETOOTH HEADSET
Dual mic with Voice Isolation
Keep this in your wallet for quick reference
PAIRING
Before use, you must pair the headset with your cell phone. Pairing will create a stored connection in
the Z9i and your Bluetooth cell phone. Pairing has to be done only once, when first connecting to a
phone. The Z9i can store pairing information for five (5) different Bluetooth devices.
Pairing Procedure - This is an example procedure only.
These steps may differ from phone to phone, but the process will be the same.
1. First turn the phone OFF and then back ON again to refresh its memor y.
2. Bring the mobile phone to about 30cm from the Z9i Dual Microphone.
3. Find the Bluetooth menu in your mobile phone. Turn Bluetooth ON.
4. With the Z9i OFF, Press and Hold the MFB for about 6 seconds until the LED flashes Blue.
5. Your headset is now ready to be discovered by your Bluetooth mobile phone.
6. Perform a Bluetooth device discovery on your mobile phone t o add a new device. It takes a few
seconds to search for and find other Bluetooth devices around you.
7. When Bluetooth devices are found, the phone will display "BlueAnt Z9i". Scr oll to it and press OK
to confirm that you want to pair with it.
8.
Enter the Passkey "0000" when your phone prompts you. The phone will now pair with the BlueAnt Z9i.
9. If your Bluetooth phone menu supports it "set as authorized" or "add to trusted devices"
10. Again select the BlueAnt Z9i to connect with it. OR, Press the MFB to connect with the phone.
(Check your mobile phone user guide)
Standby Mode means
connected to a device
but not on a call.
BUTTON FUNCTION MATRIX
Idle Mode means the Z9i
is ON but not connected
to any device
Multiple button presses
means click together
Z9i Function Button Time Status
3 Seconds From OFF
MFB
Power ON
3 Seconds Idle/Standby
MFB
Power OFF
6 Seconds From OFF
Click Ringing
MFB
MFB
Enter Pairing Mode
Answer Call
Click Active
3 Seconds Active Call
3 Seconds Active
Click Connected
3 Seconds Standby
Click Active Call
Click Standby
1 Second Active Call
MFB
MFB
Voice Dial Activate
Switch Voice Isolation
between Standard and Max
Vol
Volume Up
Click Active Call
Vol
Volume Down
Click Active Call
1 Second Ringing
Vol
MFB
MFB
End Call
Reject Call
Redial Last Number
3 Seconds Active Call
Vol
Mute
Advanced Z9i Functions
3 Seconds Active
&
Vol
MFB
Disconnect/ Transfer
Multi-Point - Place phone 1
on hold and receive phone 2
Multi-Point – End phone 2,
Vol
MFB
Call Conference
– Active phone only
return to phone 1
Multi-Point - End phone 1
receive phone 2
3 Seconds Active Call
3 Seconds Idle/Standby
&
&
Call Waiting
– Active phone only
Turn LED’s OFF/ON
Click Idle
&
&
MFB
Reset Device
Loading...