BlueAnt S4 User Manual

0 (0)

S4 USER GUIDE

Read Me to Get the Most Out of Your Device...

BlueAnt S4 User Manual

Contents

Introduction

4

Remove the Protective Cover

5

Charge Your S4

5

Pair the S4 with your Phone

6

Install the S4 in your Car

8

Using the Handsfree Trigger

9

Handsfree Trigger Battery Saving Mode

10

Reconnecting to the S4

11

Use Your Voice to Make Phone Calls

12

Use Your Voice to Answer Calls

12

Voice Commands

13

Transferring your Phonebook Contacts to the S4

15

Listening to Audio

Adjusting the Volume

Using 2 Phones with the S4 (Multipoint) Multiple Calls (Call Waiting)* Switching the S4 On and Off

Resetting the S4

Troubleshooting

Alternatives to Voice Control

Help and Support

Specifications

Terms and Conditions

17

ENGLISH

18

 

19

 

20

21

22

23

28

29

30

31

3

Introduction

The S4 speakerphone is the first true handsfree voice controlled Bluetooth car speakerphone.

There is no need to take your hands off the wheel or your eyes off the road to use the S4.

Simply say the trigger phrase BlueAnt Speak To Me™ and the S4 will be ready for your voice commands.

You can make outgoing calls and answer incoming calls using just your voice, and you will always know who is calling you without looking at your phone because the S4 will read out the

4 caller’s name or number when the phone rings.

 

Touch-Sensitive

 

Volume Controls

Battery

Handsfree

Indicator

Trigger

 

Indicator

 

Microphone

Multi-Function

 

Button (the

Bluetooth

symbol)

Indicator

Remove the Protective Cover

The plastic cover on your S4 is intended to protect it during transit. Please remove it before using your S4.

Charge Your S4

Your S4 has been given an initial partial charge to get you started, but for best results we recommend you charge it using the supplied USB cable and adaptor:

>You should charge the S4 whenever it announces that the battery is

Very Low.

>A full charge takes about 3-4 hours.

>During charging, the battery indicator light turns red.

>When the light goes out, the charge is complete.

Battery

Indicator

ON

OFF

Charging

Port

ENGLISH

5

Pair the S4 with your Phone

To use the S4 you need to pair it with your phone.

1.Slide the power switch on the side of the S4 to the ON position.

2.If this is the first time you have used the S4 it will go straight to pairing mode. The voice prompts will start to talk you through the pairing process and the light will flash blue.

For subsequent pairings, say BlueAnt Speak To Me, wait for the S4 to ask you to Say A Command and then say Pair Me.

3.Follow the voice prompts to pair the S4 with your phone. The pairing code is 0000 (four zeros).

Transfer your Phonebook

Once the pairing is complete your S4 will attempt to transfer the contacts from your phonebook so that it can announce the names of incoming callers.

Note: If your phone prompts you to allow a connection to the S4, you must select “YES” or “OK”.

6

BlackBerry®

If you are using a BlackBerry smartphone you may see a message like this one. Select “Don’t ask this again” so that a tick appears in the box, and then choose “YES”.

Android

On Android devices a message about the phonebook transfer may appear in the notifications area at the top of the screen.

In order to transfer your contacts you must swipe your finger over this message and accept the phonebook transfer request from the S4.

Automatic Transfer Not Supported

Some phones do not support automatic phonebook transfers. If this is the case on your phone the S4 will announce that it cannot transfer the contacts automatically.

See “Manually Transferring your Phonebook Contacts to the S4” on page 15 for help.

Accept connection request

 

 

 

ENGLISH

 

 

from BlueAnt S4?

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

YES

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NO

 

 

 

 

Don’t ask this again

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Phonebook Access Request

 

 

 

 

 

 

Notification

 

 

 

 

 

 

shown on

 

 

 

 

 

 

Android

 

 

 

 

 

 

devices

 

 

 

 

 

 

 

 

 

 

 

7

Install the S4 in your Car

1.Slide the sun visor clip onto the edge of the car sun visor. Your S4 is supplied with a choice of visor clips so you can select the most appropriate one for your vehicle.

2.Attach the magnetic back of the S4 to the fixed sun visor clip.

Sun Visor

Clip

Don’t forget: Drive safely and within the law.

Please refer to the relevant national or local legislation regarding the usage of mobile devices while driving. Remember that driving is your first priority: please read the enclosed safety information booklet for tips on the safe use of your BlueAnt device.

8

Using the Handsfree Trigger

Your S4 is designed to be a true handsfree device. Simply say the trigger phrase BlueAnt Speak To Me and the S4 will be ready to receive your voice commands.

1

Handsfree

2

BlueAnt

 

Speak To Me

Trigger

Say A

 

Indicator

Command

 

 

When the S4 asks you to Say A Command, immediately say one of the voice commands loudly and clearly.

Note: The handsfree trigger only works when the green handsfree trigger indicator light on the front of the device is on. This tells you that the S4 is listening for your voice.

ENGLISH

9

Handsfree Trigger Battery Saving Mode

Using the handsfree trigger gives you true handsfree operation, as the S4 is always listening for your voice.

If you want your S4 to run for longer between charges, slide the power switch to the

OFF

 

 

 

ON

middle position to activate “battery saving mode”.

 

 

 

 

 

 

 

 

 

 

In this mode the S4 only listens for 2 minutes after the last action.

 

 

 

 

 

 

 

 

 

 

Once the 2 minutes are up, the green indicator light goes out and the S4 stops listening. To re-activate the S4, tap the symbol instead of saying BlueAnt Speak To Me:

1

2

Say A

Command

10

Loading...
+ 22 hidden pages