BlueAnt T1 User Manual [en, es]

T1 QUICK START GUIDE

ENGLISH • ESPAÑOL

T1 Quick Start Guide: English

1

Microphones

Indicator

Light

Vol - Vol +

Multi-

Function

Button

(MFB)

Charging

Port

Charge Your T1

2

Your T1 has been given an initial partial charge to get
started, but for best results charge it using the supplied USB
cable and adaptor until the indicator light turns white.

> Charge the T1 whenever it announces that the battery is

Very Low.
> A full charge takes about 3 hours.
> During charging, the indicator light fl ashes red.
> When the light goes white, the charge is complete.

Pair Your T1

3

1. Turn the T1 on by
sliding the power
switch on the back to
the green on position.

2. Put the T1 in your ear.

3. The fi rst time you use the T1 it will go straight to pair
mode and talk you through the pairing process.

For subsequent pairings, make sure the T1 is not
connected to any phones, then hold down the MFB. The T1
will announce that it is going into pairing mode.

Tip: The pairing code is 0000 (four zeros).

Power switch (on)

Transfer Your Phonebook

4

Once the pairing is complete, your T1 will attempt to transfer
your phonebook contacts so that it can announce the names
of incoming callers. Please accept any connection requests
from the T1 and wait for the transfer to fi nish.

Some phones do not support automatic phonebook
transfers. If the T1 announces that this is the case, you need
to go to your phone’s address book and send contacts via
Bluetooth to the T1. See www.blueantwireless.com for help.

Note: Whenever you add contacts to your phone in future

you must update your phonebook on the T1: with the T1
connected to your phone but not on a call, hold down the
MFB for 3 seconds to initiate a phonebook update.

Wearing the T1

RIGHT
EAR

LEFT
EAR

5

You can wear your T1
on either ear.

For best results:

> Position the hook and

ear gel as shown here.

> Make sure the T1 is angled

towards your mouth.

Protective Skins

Your T1 is supplied with optional rubber
skins to protect against dust and
moisture.

Making Calls

6

Use your voice to make calls:

1. Click the MFB and wait for the T1 to ask you

to Say A Command.

2. Say Phone Commands to activate the voice

dial feature on your phone (if supported by
your phone).

Or:

> Dial the number on your phone and the audio will

automatically transfer to the T1.

> Hold down Vol + for 1 second to redial the last outgoing

call.

Taking Calls

7

When the phone rings, you can answer the
call with your voice: wait for the prompt to ask
you if you want to take the call, and then say

Answer or Ignore.

If you don’t want to wait for the prompt, or you
are in a noisy place:

> Click the MFB once to accept the call.
> Double click the MFB to reject the call.

During a call, click the MFB to end the call.

Voice Commands

8

To use any of the voice commands, click the MFB, wait for
the T1 to ask you to Say A Command, then say the command:

> Check Battery — Tells you the battery level on the T1.
> Call Information — Calls an information service number

stored in your headset. Call charges may apply.

> Phone Commands — Activates your phone’s voice dialing

feature (if available on your phone). Depending on your
phone model, you may need to record voice tags on the
phone to use this feature.

Voice recognition will cancel automatically after a short
period of time if you do not say a command. You can also
cancel voice recognition by clicking the MFB.

Listening to Audio

9

The T1 supports A2DP audio streaming: if your phone or
Bluetooth device supports the A2DP profi le then you can
simply start playing music or any other audio (including
directions from a GPS application on the phone) and it will
automatically transfer to the T1.

The audio will mute automatically if you make or receive a
phone call, and resume when the call ends.

Multipoint

10

Up to 2 phones can connect to the T1 at the same time. To
pair a second phone:

1. Use your phone’s Bluetooth menu to disconnect the
existing paired phone from the T1.

2. With the T1 switched on, hold down the MFB until the T1
starts to talk you through the pairing process.

3. When the pairing is complete, use the Bluetooth menu on
each phone to reconnect them to the T1.

When you have 2 phones connected, you can always answer
a call on either phone. If you initiate a call through the T1 it
will happen on the “primary phone”: the one that connected
to the T1 fi rst.

Advanced Button Functions

11

> To hold an active call and switch to an incoming or held

call, press Vol + for about 1 second.

> To end an active call and answer a new incoming call,

press Vol - for about 1 second.

> You can conference two active calls together by holding

the MFB for 3 seconds (if your phone and network support
this).

> To transfer audio to the phone, click Vol + and Vol -

together during a call.

> To disconnect your phone from the T1, click Vol + and Vol-

together when you are not on a call. Hold down Vol + for
about 1 second to reconnect.

Advanced Button Functions

12

> During a call you can mute and unmute the T1 microphone

by holding Vol + and Vol - together until the T1 beeps twice
(about 1 second).

> Whenever you add contacts to your phone you must also

update your phonebook on the T1: with the T1 connected
to your phone but not on a call, hold down the MFB for 3
seconds to initiate a phonebook update.

> To turn the fl ashing indicator light on or off, disconnect

the T1 from your phone and hold down Vol + and Vol - for
1 second.

> Click the MFB to: end a call, cancel pair mode, cancel voice

recognition, or cancel a phonebook transfer/update.

Reset your T1

13

If you are having problems with the T1, you can reset the T1
and your phone and start again:

1. Disconnect the T1 from your phone by deleting the pairing
from your phone’s Bluetooth menu.

2. Turn your phone off and back on again to clear its memory.

3. With the T1 switched on, but not connected to any phones,
click all three buttons (Vol +, Vol -, and the MFB) together.
Note that you must quickly press and release all three
buttons at the same time (do not hold down the buttons).

The T1 will reset and go straight to pairing mode.

You will now need to pair your phone with the T1 again.

Troubleshooting Tips

14

The following are some troubleshooting tips for using the T1
with specifi c phone models.

Phonebook Transfers

When you pair your phone the T1 will attempt to transfer the
contacts from your phonebook so that it can announce the
names of incoming callers.

Note: If your phone prompts you to allow a connection to the

T1, you must select “YES” or “OK”.