Blu Bathworks TSP210 User Manual
Wall Mounted Basin Mixer
Installation Guide
TSP210
TSU220
2014-01
®
1 866 907 0122 blubathworks.com
Attention - Before Installation
1. Inspect this product to assure you have all parts as shown that are required for proper installation (refer to illustration 1).
2. The valve cartridge has been factory tested and adjusted – DO NOT TAKE THE CARTRIDGE APART. Taking the cartridge apart
will void the warranty.
3. The valve body rough in depth is 15⁄8” - 21⁄8” (40-55mm) measured from the center of the inlets to the face of the finished wall.
4. Ensure that both hot and cold water feeds are properly connected and to the correct side of the rough in valve as illustrated.
5. This product must be installed by a professional contractor.
6. Refer to the specification and assembly drawings attached for installation directions.
7. Flow Pressure – Min. 25 PSI, Max. 80 PSI. Recommended pressure – 50 to 60 PSI
Installation Requirements
Please read the instructions carefully so as to avoid any damage to the fixture.
1. To ensure this product is installed properly, you must read and follow these guidelines.
2. The owner/user of the faucet must keep this information for future reference.
3. This faucet must be on-site prior to rough-in, allowing the installer to visualize the installation and to match the 8” center spread.
4. Be sure your installation conforms to local codes.
5. Refer to the specification and assembly drawings attached. Faucet is sold partially assembled but shown fully disassembled for
illustrative and service purposes only.
6. Check countertop and sink measurement to assure the spout projects far enough into the sink.
7. Inspect this product to assure you have all parts required for proper installation.
8. Use only a strap wrench or protected/smooth-jaw wrench on any finished surface.
9. Do NOT use putty during this installation.
Cleaners for fittings and accessories
To avoid damaging the surface and working components of the fittings, certain precautions must be taken in terms of usage and
subsequent cleaning as many cleaning agents contain acids for general cleaning and removing calcium deposits. When caring for
your fittings and accessories, please note the following:
- Only apply cleaners which are expressly intended for the use
- Never use any cleaner containing hydrochloric acid, formic acid or acetic acid on or near the fitting, as they can cause
considerable damage even with just one application
- Do not use cleaners containing phosphoric acid
- Do not use cleaners containing chlorine bleach solutions
- Never mix or combine cleaning agents
- Abrasive cleaners and unsuitable scouring agents such as scouring pads
Technical Support Assistance
If further assistance is required, please contact:
Product support at 1.866.907.0122 (09:00 - 17:00hrs PST) or email
technical@blubathworks.com
North America
Blu Bathworks Inc.
188 Smithe Street, Vancouver BC, Canada, V6B 6A9
T +1.604.299.0122 F +1.604.299.0125
2014-01
®
1 866 907 0122 blubathworks.com
1
Rough In Installation
Connect cold
inlet
Connect hot
inlet
1
⁄2”
Hot
inlet
1
⁄2”
Cold
inlet
TSP210 (Refer to illustration 1)
TSU220 (Refer to illustration 2)
Note: Rough-in depth for these products are provided on the protective mud guards.
1. Run 1⁄2" (12.5mm) hot and cold supply lines. The spread between supplies is 1½" for TSP210 & 8" for TSU220
on center and is NOT adjustable.
2. Install a 1⁄2” (12.5mm) sweat x 1⁄2” (12.5mm) female IPS adapter onto each supply line.
3. Verify the supplies are secure, level, at the proper spread and equal depths.
4. Connect the rough-in to the water system, hot water connected on the left and cold water connected on the
right.
5. Align and level the faucet rough-in and secure the faucet rough-in into the wall.
6. Verify the supplies and faucet body are secure, then turn on the supplies and check for leaks.
1
FOR TSP210
1
⁄2”
Hot
inlet
1
⁄2”
Cold
inlet
3
2
1
4
5
6
2014-01
®
1 866 907 0122 blubathworks.com
2
Loading...