Blu Bathworks TSP100 User Manual

0 (0)

pure·1 & opus·1

Deck Mounted Basin Mixer

Installation Guide

TSP100 TSP110

TSU100

TSU110

TSP120

TSP140

TSU140

2014-01

1 866 907 0122 blubathworks.com

Attention – Before Installation

1. Inspect this product to ensure you have all parts as shown that are required for proper installation.

2. The valve cartridge has been factory tested and adjusted – DO NOT TAKE THE CARTRIDGE APART. Taking the cartridge apart will void the warranty.

3. Ensure that both hot and cold water feeds are properly connected to the marked lav connecting.

4. This product must be installed by a professional contractor.

5. Refer to the speciﬁcation and assembly drawings attached for installation directions.

6. Flow Pressure –Min. 25 PSI, Max. 80 PSI. Recommended pressure – 50 to 60 PSI.

Installation Requirements

Please read the instructions carefully so as to avoid any damage to the ﬁxture.

1. To ensure this product is installed properly, you must read and follow these guidelines.

2. The owner/user of the faucet must keep this information for future reference.

3. Be sure your installation conforms to local codes.

4. Refer to the speciﬁcation and assembly drawings attached. Faucet is sold partially assembled but shown fully disassembled for illustrative and service purposes only.

5. Inspect this product toensure you have all parts required for proper installation.

6. Use only a strap wrench or protected/smooth-jaw wrench on any ﬁnished surface.

7. If possible, install the faucet assembly on the sink or mounting surface before setting.

8. Do NOT use putty during this installation.

Cleaners For Fittings And Accessories

To avoid damaging the surface and working components of the ﬁttings, certain precautions must be taken in terms of usage and subsequent cleaning as many cleaning agents contain acids for general cleaning and removing calcium deposits. When caring for your ﬁttings and accessories, please note the following:

- Only apply cleaners which are expressly intended for the use

- Never use any cleaner containing hydrochloric acid, formic acid or acetic acid on or near the ﬁtting, as they can

cause considerable damage

- Do not use cleaners containing phosphoric acid

- Do not use cleaners containing chlorine bleach solutions

- Never mix or combine cleaning agents

- Abrasive cleaners and unsuitable scouring agents such as scouring pads

Technical Support Assistance

If further assistance is required, please contact:

Product support at 1.866.907.0122 (09:00 - 17:00hrs PST) or email

technical@blubathworks.com

North America

Blu Bathworks Inc. 188 Smithe Street, Vancouver BC, Canada, V6B 6A9 T+1.604.299.0122 F+1.604.299.0125

2014-01

1 866 907 0122 blubathworks.com

1 1

Installation Procedure for Single Hole

Refer to illustration 1

1. Remove the locking nut and rubber washer from the brass base of the mixer.

2. Place mixer body with its escutcheon ring and o-ring still attached through the faucet hole of the mounting surface.

3. From below the mounting surface, slide the rubber washer onto the brass base so that it presses up against the mounting surface.

4. Screw the locking bolt onto the brass base by hand until tight and then turn an additional careful not to over tighten the bolt, as this may cause damage to the mounting surface.

5. Attach the supply lines to the water supply.

/4 turn using a wrench. Be

2014-01

1 866 907 0122 blubathworks.com

Installation Procedure for Three-Hole

Refer to illustration 2

1. Remove the escutcheon rings from the cartridge bodies.

2. Place the cartridge bodies up through their designated holes and then screw the escutcheon rings back on, making sure that the hole for the set screw faces backwards.

3. Tighten the cartridge bodies into place by tightening the lock nuts so that the rubber washers are pressing up against the mounting service.

4. Place the control handles into the escutcheon rings and then tighten the set screws with the provided Allen wrench to keep them in place.

5. Remove the locking nut and rubber washer from the mounting screw.

6. Place the faucet through the designated faucet hole of the mounting surface.

7. From below the mounting surface, slide the rubber pad and metal mounting support onto the mounting screw so that the rubber pad presses up against the mounting surface.

8. Screw the locking nut onto the mounting screw by hand until tight, then turn an additional careful not to overtighten the nut, as this may cause damage to the mounting surface.

9. Connect the flexible supply lines from the base of the faucet to the control handles.

10. Attach the supply lines to the water supply, hot on the left and cold on the right.

/4 turn using a wrench. Be

2014-01

1 866 907 0122 blubathworks.com

+ 9 hidden pages