®
pure·2 electronica
Thermostatic Deck-Mounted
Bathtub Mixer
Installation Guide
TEP421
2014-01
1 866 907 0122 blubathworks.com
®
Attention – Before Installation
1. Inspect this product to ensure you have all parts as shown that are required for proper installation.
2. The valve cartridge has been factory tested and adjusted – DO NOT TAKE THE CARTRIDGE APART. Taking the
cartridge apart will void the warranty.
3. Ensure that both hot and cold water feeds are properly connected to the marked lav connecting.
4. This product must be installed by a professional contractor.
5. Refer to the specification and assembly drawings attached for installation directions.
6. Flow Pressure –Min. 25 PSI, Max. 80 PSI. Recommended pressure – 50 to 60 PSI.
Installation Requirements
Please read the instructions carefully so as to avoid any damage to the fixture.
1. To ensure this product is installed properly, you must read and follow these guidelines.
2. The owner/user of the faucet must keep this information for future reference.
3. Be sure your installation conforms to local codes.
4. Refer to the specification and assembly drawings attached. Faucet is sold partially assembled but shown fully
disassembled for illustrative and service purposes only.
5. Inspect this product toensure you have all parts required for proper installation.
6. Use only a strap wrench or protected/smooth-jaw wrench on any finished surface.
7. If possible, install the faucet assembly on the sink or mounting surface before setting.
8. Do NOT use putty during this installation.
Cleaners For Fittings And Accessories
To avoid damaging the surface and working components of the fittings, certain precautions must be taken in terms
of usage and subsequent cleaning as many cleaning agents contain acids for general cleaning and removing calcium
deposits. When caring for your fittings and accessories, please note the following:
- Only apply cleaners which are expressly intended for the use
- Never use any cleaner containing hydrochloric acid, formic acid or acetic acid on or near the fitting, as they can
cause considerable damage
- Do not use cleaners containing phosphoric acid
- Do not use cleaners containing chlorine bleach solutions
- Never mix or combine cleaning agents
- Abrasive cleaners and unsuitable scouring agents such as scouring pads
Technical Support Assistance
If further assistance is required, please contact:
Product support at 1.866.907.0122 (09:00 - 17:00hrs PST) or email
technical@blubathworks.com
North America
Blu Bathworks Inc.
188 Smithe Street, Vancouver BC, Canada, V6B 6A9
T+1.604.299.0122 F+1.604.299.0125
2014-01
1 866 907 0122 blubathworks.com
1
®
INSTALLATION
1) Spout Base
• Insert the spout holder in the deck mount hole.
• Screw the upper and bottom flange to the spout holder. See drawing below.
• Screw the flexible pipe of the spout outlet. Remember to use the gaskets supplied.
2) Handshower Connection
• Insert the hand shower connection in the deck mount hole.
• Screw the upper and bottom flange to fit the hand shower
connection. See drawing below.
25mm
Note: A perfectly clean surface is recommended to facilitate flexible pipe and spring return.
2014-01
1 866 907 0122 blubathworks.com
2
®
3) Trim for tubfiller & hand shower
• Insert the chrome ring (7) in the spout (5); insert the spout (5) in the spout holder and screw the grub
screw (6); lower the chrome ring (7). Attention: don’t damage the chrome part.
• Slide the spout into its slip-in (5) and screw in the grub screw (9).
• Insert the chrome ring (11) in the hand shower connection installed in step (2)
• Hand tighten the hand shower (12) to the flex hose connection.
Attention: don’t forget the o-ring sealing.
2014-01
1 866 907 0122 blubathworks.com
3
®
4) Control Wheel Installation
• Unscrew and remove the nut and washer from the control brackets and data cables.
• Carefully pull the ‘front’ control wheel off the controls, taking care not to mix them up.
‘O’ ring
• Prepare the tub to take the control fixing brackets. 35mm/1⅜" diameter holes are required
to fit the brackets.
• Feed the control data cables through the holes, then insert the control brackets.
2014-01
1 866 907 0122 blubathworks.com
4
®
4) Control Wheel Installation (Continued)
• Feed the washer and nut onto the control data cables.
• Hand tighten onto the control bracket bodies. Help may be required at this stage.
• Push fit the ‘front’ control wheels onto the controls.
2014-01
1 866 907 0122 blubathworks.com
5
Loading...