Blu Bathworks LSeat-001 User Manual

Toilet Seat

Installation Guide

LSeat-001

duroplast

LSeat-002

plastic

LSeat-003

duroplast

LSeat-004

duroplast

LSeat-005

duroplast

LSeat-006

plastic

2014-10

1 866 907 0122 blubathworks.com

Attention — Before Installation

If you are installing this product in a new construction or remodel, please make sure you are following all local plumbing
and building codes. Carefully unpack and examine your new fixture for damage. To help insure that the installation
process will proceed smoothly and correctly, please read these instructions carefully before you begin.

- We recommend that the installation be done by a minimum of 2 people as a security precaution. Also make sure
to adopt the proper posture when lifting the basin.

- Adhere to all local building and plumbing codes. The diagrams in this guide are not construction plans. They are
visual aids.

1. Inspect this product to assure you have all parts as shown that are required for proper installation. Blu recommends

that the installer refer to the Geberit toilet system installation and maintenance instructions.

2. Read this entire instruction sheet to ensure proper installation.

3. Compliance and conformity to local building codes and ordinances is the responsibility of the installer.

4. Compliance and conformity to local fire codes and ordinances is the responsibility of the installer.

5. Purge all the water supply lines before making connections.

Installation Requirements

Please read the instructions carefully so as to avoid any damage to the fixture.

1. To ensure this product is installed properly, you must read and follow these guidelines.

2. The owner/user of the product must keep this information for future reference.

3. Consult local building codes to make sure the installation complies with standards.

4. Remove the unit from its packaging. Before disposing of it, inspect the unit to make sure its in good shape. Should
inspection reveal any damage or defect in the finish, contact your distributor. The warranty does not cover damages
or defects in the finish once it has been installed. Blu Bathworks’ responsibility for shipping damages ceases upon
delivery of the product in good order to the carrier. All complaints regarding damage due to transport must be made
directly to the carrier.

5. Place the unit in the bathroom before you start working. Conserve all nuts and bolts.

6. To protect the unit during installation, we recommend that you lay a piece of cardboard on the bottom.

7. If the unit is covered with polyethylene protective film, do not remove until installation is complete to grant maximum
protection. However, remove film where any two surfaces will be in permanent contact.

8. Verify that all dimensions on the plan are the same as the ones of the unit.

Technical Support Assistance

If further assistance is required, please contact:

Product Support at 1.866.907.0122 (09:00 – 17:00hrs PST) or email [e-mail]

North America

Blu Bathworks Inc.

188 Smithe Street,Vancouver, BC, Canada, V6B 6A9

T +1.604.299.0122 F +1.604.299.0125

Please refer to blubathworks.com for warranty, terms & conditions under warranty & procedure for warranty service.

1 866 907 0122 blubathworks.com

2014-10

1 1

Toilet Seat Installation Instructions

LSeat-001 · LSeat-002 · LSeat-003 · LSeat-004 · LSeat-005

3

1

Hinge Adjustment

4

2

5

• Maximum adjustment of the pin position is
achieved by rotating the hinge anchor around the
screw (adjustment A in the parts diagram above.)

• Further fine adjustment of the pin position can be
achieved by sliding the screw in the adjustment
plate (adjustment B).

1
2
3
4
5

2014-10

1 866 907 0122 blubathworks.com

2

Fixing the Hinge Anchor

1

1a 1b

• Make sure round
rubber gasket is
underneath hinge.

• Place the Top Fix Inserts into the fixing holes. Insert the
screws within the Hinge Anchors as shown and begin
to tighten the screws until they are loosely secured to
allow for adjustment of the seat.

Fitting the Seat

• Insert the expansion
rubbers/plastic inserts
into the hinge holes of
the toilet.

2 2a 2b 2c

Quick-Release Mechanism

3

• This toilet seat is designed for quick and easy removal when cleaning
the toilet. To activate the quick release lift the lid, seat up and press the
button in the centre of the hinges and lift.

• To replace the seat, align the sockets with the pin and firmly press into
position.

• LSeat-002 is designed to activate the quick release with NO BUTTON.
To release, lift lid and seat up, then pull up.

2014-10

1 866 907 0122 blubathworks.com

3