Blomberg WAF 6140 A User Manual [nl]
Washing Machine
WAF 6150 A - WAF 6140 A
WAF 6120 A - WAF 6100 A
WAF 6080 A
User's Manual
Contents
1- Technical Features of Your Washing Machine 3
2- Warning 5
3- Preparation 7
4- Program Selection and Starting Machine 11
5- Care and maintenance 15
6- Installation 17
7- Before calling service 19
2
Technical Features of Your Washing Machine
1
WA 6150 A
Maximum dry laundry
capacity (kg.)
Height (cm.)
Width (cm.)
Depth (cm.)
Net Weight (kg.)
Electricity (V/Hz.)
Total Current (A)
Total Power (W)
Washing -rinsing cycle
(cyc/min)
Spinning cycle (max
cyc/min)
There may be changes in the technical
features without prior notice in order to
enhance product quality.
The figures in the manual are schematic
and may not represent your actual machine one-to-one.
6 6 6 6 6
85 85 85 85 85
60 60 60 60 60
54 54 54 54 54
71 71 71 71 71
230/50 230/50 230/50 230/50 230/50
10 10 10 10 10
2350 2350 2350 2350 2350
52 52 52 52 52
1500 1400 1200 1000 800
WA 6140 A
WA 6120 A
WA 6100 A
WA 6080 A
Labelling on your product and ones
declared in the documents accompanying product are the values obtained under
laboratory conditions with given standards. These values may vary according to
usage and environmental conditions.
3
Your Washing Machine
1
Detergent dispenser
1
2
3
4
5
Front Panel
2
Front door
3
Kick Plate Cover
4
Height-adjustable feet
5
4
Warning
2
• This product is designed for home
use.
• Your washing machine is adjusted
to 230V.
• If the fuse in your house is less
than 16A than have a certified
electrician deploy an 16A fuse.
• In case of transformer or nontransformer use, grounding installation must be performed with a licensed electrician. Any use before
grounding is not our responsibility.
• In order to make your machine
ready call Authorized Service,
prepare clean tap water and water
draining with licensed plumber.
• Never place your machine over a
carpet covered floor. Otherwise
electrical parts of your machine
may overheat. This may cause
malfunction of your machine.
• Make sure hot and cold taps are
connected correctly. Otherwise
your laundry may come out hot
and torn .
• Please call certified service for a
failure of electric plug / cable.
• Be careful about your water hoses
are not old. Do not use old / torn
water hoses. This may cause stain
in your laundry .
• At first use, washing must be
performed at Cotton 90°C program
without loading with laundry for
getting your machine ready for
washing.
• Performance of your washing
machine depends on the quality
of water and hygiene compound
used. If low quality and unfitting
cleaning material is used the
stains will be fixed. Before washing your laundry with stain keep
your attention on cleaning the
laundry as explained in following
pages.
• This is period of keeping spare
parts for your machine to operate.
Because of quality control procedures there might be little amount
of water in your machine. This
does not have any damage to your
machine.
• Your machine is programmed for
starting operation again when
electricity is off and on afterwards.
You can not press On / Off button
to cancel program. Machine will
go on program when electricity is
on. To CANCEL the program press
>Start/Pause/Cancel< button for
three seconds. (See. Cancelling a
program)
If “Door” led on program progress
display is blinking program selection knob is middle position. In this
case turn the knob and adjust it
again. If the warning continues call
authorized service.
• After your machine starts opera-
tion, if Start/Pause/Cancel key
starts blinking than door is not
locked. Open and close the door
again begin washing program
again.
• If the “washing” led on the pro-
gram progress display is blinking
either there is no water or tap is
5
off. Check your taps. Turn your
machine off and on. If the problem
persists unplug your machine, turn
off tap water and call authorized
service.
• If program is started and program
selection can not be performed
your machine might be in protection mode due to infrastructure
problem (voltage, water pressure,
etc.) Press and hold the > Start/
Pause/Cancel < button for 3 seconds in order to switch machine to
factory settings.
• Most of the warnings resulting in
calling an authorized service are
due to infrastructure problems. For
this reason applying to an Authorized Service is recommended.
6
Loading...