Do not operate this equipment unless you
have read and understood the contents
of this manual! Failure to follow the
instructions contained in this manual
may result in serious injury or death.
This manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
English = p 2
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en
este manual puede resultar en un serio
lesión o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted
no puede entender el contenido de
este manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
AVERTISSEMENT
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel ! Le
non-respect des instructions contenues
dans ce manuel peut entraîner de
graves blessures ou la mort. Ce manuel
contient des informations importantes
concernant l’entretien, l’utilisation et le
fonctionnement de ce produit. Si vous ne
comprenez pas le contenu de ce manuel,
veuillez le signaler à votre supérieur.
Conservez ce manuel dans un endroit
sûr pour pouvoir vous y référer plus tard.
Record the model number, serial number, voltage, and
purchase date of the unit in the spaces below (specification
label on bottom of GRS model, bottom of control box on GRSB
and GRSBF models). Please have this information available
when calling Hatco for service assistance.
Model No. _______________________________________
Serial No. ________________________________________
Voltage __________________________________________
Date of Purchase __________________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
www.hatcocorp.com, select the Parts & Service pull-down
menu, and click on “Warranty Registration”.
Glo-Ray Heated Shelves are a product of extensive research
and field testing. The materials used were selected for maximum
durability, attractive appearance, and optimum performance.
Every unit is inspected and tested thoroughly prior to shipment.
This manual provides the installation, safety, and operating
instructions for the Glo-Ray Heated Shelf. Hatco recommends
all installation, operating, and safety instructions appearing in
this manual be read prior to installation or operation of the GloRay Heated Shelf.
Safety information that appears in this manual is identified by
the following signal word panels:
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to
personal injury.
2
Form No. GRSM-1115
English
WARNING
WARNING
CAUTION
NOTICE
IMPORTANT SAFETY INFORMATION
Read the following important safety information before using this equipment to avoid
serious injury or death and to avoid damage to equipment or property.
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install the proper voltage
and size electrical receptacle.
• Turn OFF power switch, unplug power cord, and
allow unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• This unit is not “jet-proof” construction. Do not use
jet-clean spray to clean this unit.
• Do not steam clean or use excessive water on unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged
power cord. The cord must be replaced by Hatco, an
Authorized Hatco Service Agent, or a person with
similar qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Remote control enclosure must be mounted on vertical
wall and installed in vertical position. Mounting remote
control enclosure in horizontal position may result in
collection of liquids and lead to electric shock.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
Make sure food product has been heated to the proper
food-safe temperature before placing on the unit. Failure
to heat food product properly may result in serious health
risks. This unit is for holding preheated food product only.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them
away from the unit.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax 800-690-2966; or
International fax 414-671-3976.
BURN HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
Locate unit at proper counter height in an area that is
convenient for use. The location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of unit and contents.
Do not operate built-in models without control box
mounted properly as described in installation instructions.
Do not operate unit without installing supplied legs.
The National Sanitation Foundation (NSF) requires that
units over 36″ (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above
installation surface. If unit cannot be sealed at the point
of use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
Unit is designed and recommended for use in or on
metallic countertops. Damage to any countertop material
is not covered under the Hatco warranty. For other
surfaces, verify with manufacturer that material is suitable
for prolonged temperatures up to 200°F (93°C).
Do not modify wiring or cut thermostat capillary on control
enclosure to increase remote mounting distance. Cutting
thermostat capillary will cause unit to overheat and may
damage unit as well as surrounding countertop.
Do not use excessive force when tightening mounting
screws on built-in units. This may damage unit and/or
countertop.
Do not lay unit on the side with the control panel. Damage
to unit could occur.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch the finish of the unit,
marring its appearance and making it susceptible to soil
accumulation.
Install remote mounted control enclosure outside of heat
zone. Locating control enclosure inside heat zone will
cause control(s) to overheat, malfunction, and fail.
Do not slide pans across hardcoat surface, use roughbottomed pans, or drop anything on hardcoat surface.
Scratching may occur. Damage to hardcoat surface caused
by misuse is not covered under warranty.
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
Form No. GRSM-1115
3
MODEL DESCRIPTION
GRSB Recessed Top Model
GRSBF Flat Top Model
G R S B F - XX - F
Glo-Ray
Heated Shelf
B = Built-In
No Character = Free Standing
F = Flat
No Character = Recessed Top
Model Width (inches)
Heated Depth
GRSBF Models
F = 17″ (432 mm)
I = 21″ (533 mm)
S = 25-1/2″ (648 mm)
O = 31-1/2″ (800 mm)
GRSB Models
F = 15-1/2″ (394 mm)
I = 19-1/2″ (495 mm)
O = 30″ (762 mm)
GRS Models
I = 19-1/2″ (495 mm)
A = 6″ (152 mm)
B = 7-3/4″ (197 mm)
C = 9-3/4″ (248 mm)
D = 12″ (305 mm)
E = 13-3/4″ (349 mm)
F = 15-1/2″ (394 mm)
G = 15-3/4″ (400 mm)
H = 17-1/2″ (445 mm)
J = 21-1/2″ (546 mm)
K = 23-1/2″ (597 mm)
L = 25-1/2″ (648 mm)
English
GRS Model
The GRS Heated Shelf is ideal for pass-through areas, buffet
lines, or as a heated work shelf. It features a Power On/Off
rocker switch with indicator light, an adjustable thermostat
control, and a 6′ (1829 mm) power cord with plug. Surface
mounted, blanket-type foil elements distribute heat under the
entire stainless steel or hardcoat aluminum surface.
All GRS models are shipped from the factory completely
assembled (except legs) and ready for use.
GRS Model
GRSB and GRSBF Models
The GRSB and GRSBF Built-In Heated Shelves have a
hardcoat aluminum surface and a blanket-type foil element for
uniform heat distribution. Ideal for server-to-customer passthrough areas, buffet/cafeteria lines, and other self-service
areas. The GRSB model features a recessed top. The GRSBF
model features a flat top.
A 36″ (914 mm) flexible conduit channels the power lines
from the shelf to a control box. The control box comes with an
illuminated POWER ON/OFF (I/O) rocker switch, an adjustable
thermostat control, and mounting brackets. The attached
control box can be mounted semi-remotely up to 36″ (914 mm)
from the unit. A 6′ (1829 mm) power cord and plug is attached
to the control box.
The GRSB and GRSBF models have a 3/4″ (19 mm) flanged
edge that allows the unit to drop into a countertop opening for
recessed mounting. The shelves are easy to clean with a nonabrasive, damp cloth and/or non-abrasive cleaner. All GRSB
and GRSBF models are shipped from the factory completely
assembled and ready for installation.
GRSB and GRSBF Models
MODEL DESIGNATION
4
Form No. GRSM-1115
English
WARNING
D
B
Front ViewSide View
A
C
E
NEMA 5-15PNEMA 5-20P
NEMA 6-15P
CEE 7/7 SchukoBS-1363
SPECIFICATIONS
Plug Configurations
Units are supplied from the factory with an electrical cord and
plug installed. Plugs are supplied according to the application.
ELECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of the correct voltage,
size, and plug configuration. If plug and receptacle do not
match, contact a qualified electrician to determine and
install the proper voltage and size electrical receptacle.
NOTE: The specification label is located on the bottom of GRS
models and the bottom of the remote control box on
GRSB and GRSBF models. See label for serial number
and verification of unit electrical information.
GRS-18-A1201000.8NEMA 5-15P16 lbs. (7 kg)
GRS-18-B1201000.8NEMA 5-15P16 lbs. (7 kg)
GRS-18-C1201251.0NEMA 5-15P16 lbs. (7 kg)
GRS-18-D1202001.7NEMA 5-15P16 lbs. (7 kg)
GRS-18-E1202001.7NEMA 5-15P16 lbs. (7 kg)
GRS-18-F1202001.7NEMA 5-15P16 lbs. (7 kg)
GRS-18-G1202251.9NEMA 5-15P16 lbs. (7 kg)
GRS-18-H1202251.9NEMA 5-15P16 lbs. (7 kg)
GRS-18-J1203002.5NEMA 5-15P16 lbs. (7 kg)
GRS-18-K1203252.7NEMA 5-15P16 lbs. (7 kg)
GRS-18-L1203502.9NEMA 5-15P16 lbs. (7 kg)
GRS-24-A1201251.0NEMA 5-15P20 lbs. (9 kg)
GRS-24-B1201251.0NEMA 5-15P20 lbs. (9 kg)
GRS-24-C1201751.5NEMA 5-15P20 lbs. (9 kg)
GRS-24-D1202502.1NEMA 5-15P20 lbs. (9 kg)
GRS-24-E1202502.1NEMA 5-15P20 lbs. (9 kg)
GRS-24-F1202502.1NEMA 5-15P20 lbs. (9 kg)
GRS-24-G1203002.5NEMA 5-15P20 lbs. (9 kg)
GRS-24-H1203002.5NEMA 5-15P20 lbs. (9 kg)
GRS-24-J1203753.1NEMA 5-15P20 lbs. (9 kg)
GRS-24-K1204253.5NEMA 5-15P20 lbs. (9 kg)
GRS-24-L1204754.0NEMA 5-15P20 lbs. (9 kg)
GRS-30-A1201501.3NEMA 5-15P25 lbs. (11 kg)
GRS-30-B1201501.3NEMA 5-15P25 lbs. (11 kg)
GRS-30-C1202251.9NEMA 5-15P25 lbs. (11 kg)
GRS-30-D1203002.5NEMA 5-15P25 lbs. (11 kg)
GRS-30-E1203002.5NEMA 5-15P25 lbs. (11 kg)
GRS-30-F1203002.5NEMA 5-15P25 lbs. (11 kg)
GRS-30-G1203753.1NEMA 5-15P25 lbs. (11 kg)
GRS-30-H1203753.1NEMA 5-15P25 lbs. (11 kg)
GRS-30-J1204503.8NEMA 5-15P25 lbs. (11 kg)
GRS-30-K1205254.4NEMA 5-15P25 lbs. (11 kg)
GRS-30-L1206005.0NEMA 5-15P25 lbs. (11 kg)
GRS-36-A1201751.5NEMA 5-15P28 lbs. (13 kg)
GRS-36-B1201751.5NEMA 5-15P28 lbs. (13 kg)
GRS-36-C1202752.3NEMA 5-15P28 lbs. (13 kg)
GRS-36-D1203502.9NEMA 5-15P28 lbs. (13 kg)
GRS-36-E1203502.9NEMA 5-15P28 lbs. (13 kg)
GRS-36-F1203502.9NEMA 5-15P28 lbs. (13 kg)
GRS-36-G1204503.8NEMA 5-15P28 lbs. (13 kg)
GRS-36-H1204503.8NEMA 5-15P28 lbs. (13 kg)
GRS-36-J1205254.4NEMA 5-15P28 lbs. (13 kg)
GRS-36-K1206255.2NEMA 5-15P28 lbs. (13 kg)
GRS-36-L1207256.0NEMA 5-15P28 lbs. (13 kg)
GRS-42-A1202251.9NEMA 5-15P32 lbs. (15 kg)
GRS-42-B1202251.9NEMA 5-15P32 lbs. (15 kg)
GRS-42-C1203002.5NEMA 5-15P32 lbs. (15 kg)
GRS-42-D1204503.8NEMA 5-15P32 lbs. (15 kg)
GRS-42-E1204503.8NEMA 5-15P32 lbs. (15 kg)
GRS-42-F1204503.8NEMA 5-15P32 lbs. (15 kg)
GRS-42-G1205254.4NEMA 5-15P32 lbs. (15 kg)
GRS-42-H1205254.4NEMA 5-15P32 lbs. (15 kg)
GRS-42-J1206755.6NEMA 5-15P32 lbs. (15 kg)
GRS-42-K1207506.3NEMA 5-15P32 lbs. (15 kg)
GRS-42-L1208256.9NEMA 5-15P32 lbs. (15 kg)
SPECIFICATIONS
continued...
NOTE: The last letter in the above models indicate the following depths:
GRS-48-A1202502.1NEMA 5-15P36 lbs. (16 kg)
GRS-48-B1202502.1NEMA 5-15P36 lbs. (16 kg)
GRS-48-C1203502.9NEMA 5-15P36 lbs. (16 kg)
GRS-48-D1205004.2NEMA 5-15P36 lbs. (16 kg)
GRS-48-E1205004.2NEMA 5-15P36 lbs. (16 kg)
GRS-48-F1205004.2NEMA 5-15P36 lbs. (16 kg)
GRS-48-G1206005.0NEMA 5-15P36 lbs. (16 kg)
GRS-48-H1206005.0NEMA 5-15P36 lbs. (16 kg)
GRS-48-J1207506.3NEMA 5-15P36 lbs. (16 kg)
GRS-48-K1208507.1NEMA 5-15P36 lbs. (16 kg)
GRS-48-L1209507.9NEMA 5-15P36 lbs. (16 kg)
GRS-54-A1202752.3NEMA 5-15P42 lbs. (19 kg)
GRS-54-B1202752.3NEMA 5-15P42 lbs. (19 kg)
GRS-54-C1204003.3NEMA 5-15P42 lbs. (19 kg)
GRS-54-D1205504.6NEMA 5-15P42 lbs. (19 kg)
GRS-54-E1205504.6NEMA 5-15P42 lbs. (19 kg)
GRS-54-F1205504.6NEMA 5-15P42 lbs. (19 kg)
GRS-54-G1206755.6NEMA 5-15P42 lbs. (19 kg)
GRS-54-H1206755.6NEMA 5-15P42 lbs. (19 kg)
GRS-54-J1208256.9NEMA 5-15P42 lbs. (19 kg)
GRS-54-K1209507.9NEMA 5-15P42 lbs. (19 kg)
GRS-54-L12010759.0NEMA 5-15P42 lbs. (19 kg)
GRS-60-A1203002.5NEMA 5-15P44 lbs. (20 kg)
GRS-60-B1203002.5NEMA 5-15P44 lbs. (20 kg)
GRS-60-C1204503.8NEMA 5-15P44 lbs. (20 kg)
GRS-60-D1206005.0NEMA 5-15P44 lbs. (20 kg)
GRS-60-E1206005.0NEMA 5-15P44 lbs. (20 kg)
GRS-60-F1206005.0NEMA 5-15P44 lbs. (20 kg)
GRS-60-G1207506.3NEMA 5-15P44 lbs. (20 kg)
GRS-60-H1207506.3NEMA 5-15P44 lbs. (20 kg)
GRS-60-J1209007.5NEMA 5-15P44 lbs. (20 kg)
GRS-60-K12010508.8NEMA 5-15P44 lbs. (20 kg)
GRS-60-L120120010.0NEMA 5-15P44 lbs. (20 kg)
GRS-66-A1203252.7NEMA 5-15P50 lbs. (23 kg)
GRS-66-B1203252.7NEMA 5-15P50 lbs. (23 kg)
GRS-66-C1205004.2NEMA 5-15P50 lbs. (23 kg)
GRS-66-D1206505.4NEMA 5-15P50 lbs. (23 kg)
GRS-66-E1206505.4NEMA 5-15P50 lbs. (23 kg)
GRS-66-F1206505.4NEMA 5-15P50 lbs. (23 kg)
GRS-66-G1208256.9NEMA 5-15P50 lbs. (23 kg)
GRS-66-H1208256.9NEMA 5-15P50 lbs. (23 kg)
GRS-66-J1209758.1NEMA 5-15P50 lbs. (23 kg)
GRS-66-K12011509.6NEMA 5-15P50 lbs. (23 kg)
GRS-66-L120132511.0NEMA 5-15P50 lbs. (23 kg)
GRS-72-A1203502.9NEMA 5-15P56 lbs. (25 kg)
GRS-72-B1203502.9NEMA 5-15P56 lbs. (25 kg)
GRS-72-C1205504.6NEMA 5-15P56 lbs. (25 kg)
GRS-72-D1207005.8NEMA 5-15P56 lbs. (25 kg)
GRS-72-E1207005.8NEMA 5-15P56 lbs. (25 kg)
GRS-72-F1207005.8NEMA 5-15P56 lbs. (25 kg)
GRS-72-G1209007.5NEMA 5-15P56 lbs. (25 kg)
GRS-72-H1209007.5NEMA 5-15P56 lbs. (25 kg)
GRS-72-J12010508.8NEMA 5-15P56 lbs. (25 kg)
GRS-72-K120125010.4NEMA 5-15P56 lbs. (25 kg)
GRS-72-L120145012.0NEMA 5-15P56 lbs. (25 kg)
English
NOTE: The last letter in the above models indicate the following:
22013726.2CEE 7/7 Schuko53 lbs. (24 kg)
24016346.8BS-136353 lbs. (24 kg)
GRSBF-60-O120175014.6NEMA 5-20P54 lbs. (25 kg)
24017507.3NEMA 6-15P54 lbs. (25 kg)
220–230 (CE)1750-19128.0-8.3CEE 7/7 Schuko54 lbs. (25 kg)
230–240 (CE)1607-17507.0-7.3BS-136354 lbs. (25 kg)
GRSBF-72-F12011309.4NEMA 5-15P52 lbs. (24 kg)
GRSBF-72-I100144014.4NEMA 5-15P58 lbs. (26 kg)
120144012.0NEMA 5-15P58 lbs. (26 kg)
GRSBF-72-S120175014.6NEMA 5-20P62 lbs. (28 kg)
22016027.3CEE 7/7 Schuko62 lbs. (28 kg)
24019067.9BS-136362 lbs. (28 kg)
GRSBF-72-O208207010.0NEMA 6-15P64 lbs. (29 kg)
24020708.6NEMA 6-15P64 lbs. (29 kg)
220–230 (CE)2070-22629.4-9.8CEE 7/7 Schuko64 lbs. (29 kg)
230–240 (CE)1901-20708.3-8.6BS-136364 lbs. (29 kg)
English
The shaded areas contain electrical information for International models only.
INSTALLATION
General
Use the following procedures to install the GRS, GRSB, and
GRSBF units.
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
Locate unit at proper counter height in an area that is
convenient for use. The location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of unit and contents.
Do not operate built-in models without control box mounted
properly as described in the installation instructions.
Do not operate unit without installing supplied legs.
The National Sanitation Foundation (NSF) requires that
units over 36″ (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point
of use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
NOTICE
Do not operate unit prior to installing legs. Damage to unit
could occur.
GRS Models
1. Remove the unit from the carton and place it upside down
on the cardboard.
NOTE: To prevent delay in obtaining warranty coverage,
2. Install the 1″ (25 mm) legs to the
unit.
a. Thread a foot stud into the
b. Slip a rubber foot over each
NOTE:If 4″ (102 mm) legs are
3. Turn unit upright, and place unit in the desired location.
• Locate the unit in an area where the ambient air
• Make sure the unit is at the proper counter height in an
• Make sure the countertop is level and strong enough to
• Make sure all the feet on the bottom of the unit are
14
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
hole at each corner on the
bottom of the unit. Tighten
securely, but do not overtighten.
foot stud.
required, refer to the OPTIONS AND ACCESSORIES
section in this manual for installation instructions.
temperature is constant and a minimum of 70° F (21° C).
Avoid areas that may be subject to active air movements
or currents (i.e., near exterior doors, exhaust fans/
hoods, air conditioning ducts, etc...).
area convenient for use.
support the weight of the unit and food product.
positioned securely on the countertop.
Form No. GRSM-1115
English
Bracket Screw
NOTICE
Panel
Under Counter
Surface
7-1/4″
(184 mm)
2″
(51 mm)
2-1/8″
(54 mm)
7″
(178 mm)
INSTALLATION
GRSB and GRSBF Models
1. Remove the unit from the carton and place it upside down
on the cardboard.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
Underside of GRSB Models
2. Remove and save the bracket screws from the underside
of the unit.
NOTE: The control box may be moved to the most convenient
location on the underside of the unit. For semi-remote
installations, leave the control box in place until the unit
is placed into the countertop.
NOTICE
Unit is designed and recommended for use in or on
metallic countertops. Damage to any countertop material
is not covered under the Hatco warranty. For other
surfaces, verify with manufacturer that material is suitable
for prolonged temperatures up to 200°F (93°C).
3. Prepare countertop opening. Refer to the appropriate
“Countertop Cutout” chart on the following pages for
recommended countertop cutout dimensions.
4. Apply a bead of NSF-approved sealant between the
countertop material and the mounting flange on the
unit. The sealant must be rated for use at a minimum
temperature of 250°F (121°C).
5. Place the unit into the countertop opening.
6. Assemble the Z-brackets to the underside of the unit using
the four bracket screws removed earlier in this procedure
(refer to the illustrations on the following pages).
Z-brackets to be installed midway along the front and
rear of the unit.
7. Adjust the mounting screws on the Z-brackets until the top
flange lies flat on the countertop.
8. Remove any excess sealant.
9. If desired or necessary, the control box can be mounted in
a semi-remote location.
a. Remove the control box from the bottom of the unit.
b. If necessary, remove the end brackets from the control
box, rotate/reposition, and re-secure to the control box.
c. The control box can be panel, surface, under counter, or
recess mounted.
Control Box Mounting Options
d. The distance the control box can be mounted from the
unit is determined by the 36″ (914 mm) conduit. Do not
pull the conduit tight to increase the mounting distance.
The conduit should have some slack after the control
box is mounted.
NOTICE
Do not modify wiring or cut thermostat capillary on control
enclosure to increase-remote mounting distance. Cutting
thermostat capillary will cause unit to overheat and may
damage unit as well as surrounding countertop.
10. Once all components are secured, proceed to the
OPERATION section.