Blaupunkt Rio de Janeiro 120 Owner's Manual

1

OWNER’S MANUAL

Mobile Audio System

RIO DE JANEIRO 120BT

 PLL Synthesizer Stereo Radio
 MP3/WMA Player
 Full Detachable Panel
 USB/ SD Interface
 3.5mm Jack Input
 Bluetooth function
 Remote control function

2

CONTENTS

Installation ........................................... 3

Take out screw before installation ......... 3

DIN Front-Mount (Method A) ................. 3

Installing the unit ............................... 3

Removing the unit ............................. 4

DIN Rear-Mount (Method B) ................. 5

Using the detachable front panel ...... 6

Wiring Connection .............................. 7

Operation ............................................. 8

Location of keys .................................... 8

Switching on/off the unit ........................ 9

Faceplate release ................................. 9

Sound adjustment ................................. 9

Display information ............................... 10

Liquid crystal display ............................. 10

Reset function ....................................... 10

Radio operation .................................... 10

Switching to radio mode .................... 10

Selecting the frequency band ............ 10

Selecting station ................................ 10

Automatic memory storing& program

scanning ............................................ 11

Station storing ................................... 11

RDS operation ...................................... 11

USB play operation ............................... 12

Selecting tracks ................................. 12

Pausing playing ................................. 12

Scan play all tracks ........................... 12

Repeating the same track ................. 12

Playing all tracks in random .............. 12

Select directory

up/down..............................12

Selecting files by button ............... 12

TF Card operation ............................. 13

Bluetooth operation ............................... 13

Remote control .................................... 15

Specification ........................................ 17

Trouble shooting ................................. 18

3

INSTALLATION

Notes:

 Choose the mounting location where

the unit will not interfere with the
normal driving function of the driver.

 Before finally installing the unit, connect

the wiring temporarily and make sure it
is all connected up properly and the
unit and the system work properly.

 Use only the parts included with the

unit to ensure proper installation. The
use of unauthorized parts can cause
malfunctions.

 Consult with your nearest dealer if

installation requires the drilling of holes
or other modifications of the vehicle.

 Install the unit where it does not get in

the driver’s way and cannot injure the
passenger if there is a sudden stop, like
an emergency stop.

 If installation angel exceeds 30°from

horizontal, the unit might not give its
optimum performance.

 Avoid installing the unit where it would

be subject to high temperature, such as
from direct sunlight, or from hot air,
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either
from “Front” (conventional DIN Front-mount)
or “Rear” (DIN Rear-mount installation,
utilizing threaded screw holes at the sides
of the unit chassis). For details, refer to the
following illustrated installation methods.

DIN FRONT-MOUNT (Method A)

Installation Opening
This unit can be installed in any dashboard
having an opening as shown below:

Installing the unit
Be sure you test all connections first, and
then follow these steps to install the unit.

1. Make sure the ignition is turned off, and
then disconnect the cable from the
vehicle battery’s negative (-) terminal.

2. Disconnect the wire harness and the
antenna.

3. Press the release button on the front
panel and remove the control panel
(see the steps of “removing the front
panel”).

4. Lift the top of the outer trim ring then pull
it out to remove it.

5. The two supplied keys release tabs
inside the unit’s sleeve so you can
remove it. Insert the keys as far as

they will go (with the notches facing up)
into the appropriate slots at the middle
left and right sides of the unit. Then slide
the sleeve off the back of the unit.

30

Outer Trim Ring

Front Panel

L Key

Sleeve

R Key

53mm

182mm

4

INSTALLATION

6. Mount the sleeve by inserting the sleeve
into the opening of the dashboard and
bend open the tabs located around the
sleeve with a screwdriver. Not all tabs
will be able to make contact, so
examine which ones will be most
effective. Bending open the appropriate
tabs behind the dashboard to secure
the sleeve in place.

7. Reconnect the wire harness and the
antenna and be careful not to pinch any
wires or cables.

8. Slide the unit into the sleeve until it
locks into place.

9. To further secure the unit, use the
supplied metal strap to secure the

back of the unit in place. Use the supplied
hardware (Hex Nut (M5mm) and Spring
Washer) to attach one end of the strap to
the mounting bolt on the back of the unit.
If necessary, bend the metal strap to fit
your vehicle’s mounting area. Then use
the supplied hardware (Tapping Screw
(5x25mm) and Plain Washer) to attach
the other end of metal strap to a solid
metal part of the vehicle under the
dashboard. This strap also helps ensure
proper electrical grounding of the unit.

Note to install the short threading

terminal of the mounting bolt to the back
of the unit and the other long threading
terminal to

the dashboard.

Mounting Bolt

Spring Washer

Plain Washer

Tapping Screw

Hex Nut

Metal Strap

10. Reconnect t he cable to the v ehicle
battery’s negative (-) terminal. Then
replace the outer trim ring and install the
unit’s front panel (see the steps of
“installing the front panel”).

Removing the unit

1. Make sure the ignition is turned off, then

disconnect the cable from the vehicle
battery’s negative (-) terminal.

2. Remove the metal strap attached the

back of the unit (if attached).

3. Press the release button to remove the

front panel.

4. Lift the top of the outer trim ring then pull

it out to remove it.

5. Insert both of the supplied keys into the

slots at the middle left and right sides of
the unit, then pull the unit out of the
dashboard.

5

INSTALLATION

DIN REAR-MOUNT (Method B)

If your vehicle is a Nissan, Toyota, follow
these mounting instructions.
Use the screw holes marked T (Toyota), N
(Nissan) located on both sides of the unit to
fasten the unit to the factory radio mounting
brackets supplied with your vehicle.

Dashboard or Console

Screw

Factory Radio
Mounting Bracket

Side View showing
Screw Holes marked
T, N

Screw

To fasten the unit to the factory radio
mounting brackets.
Align the screw holes on the bracket with
the screw holes on the unit, and then
tighten the screws (5x5mm) on each side.
Note: the outer trim ring, sleeve and the
metal strap are not used for method B
installation.

6

REMOVING THE FRONT PANEL

- Press the release button ( ) on the
front panel and pull off the front panel.

- Keep front panel into the case.

INSTALLING THE FRO NT PANEL

To install the front panel, insert the panel
into the housing and make sure the panel is
properly installed. Otherwise, abnormality
occurs on the display or some keys will not
function properly.

Precautions when handling

- Do not drop the front panel.

- Do not put pressure on the display or
control buttons when removing or
installing the front panel.

- Do not touch the contacts on the front
panel or on the main unit body. It may
result in poor electrical contact.

- If any dirt or foreign substances
adhered on the contacts, they can be
removed with a clean and dry cloth.

- Do not expose the front panel to high
temperatures or direct sunlight in
anywhere.

- Keep away any volatile agents (e.g.
benzene, thinner, or insecticides) from
touching the surface of the front panel

- Do not attempt to disassemble the front
panel.

USING THE DETACHABLE FRONT PANEL