In Car Video
IVSC-5502
Operating and installation instructions
http://www.blaupunkt.com
CONTENTS
General information ............... 11
Installation and safety notices ........ 11
Accessories .................................. 11
Supplied parts ........................ 12
Switching on/off .................... 12
Switching on the signal controller .. 12
Switching off the signal controller .. 12
Settings .................................. 13
External monitor switch (Fig. 2)...... 13
Monitor connections ...................... 13
IR remote control ................... 13
Functions ...................................... 13
Settings for Audio OUT ................. 14
Installation.............................. 15
Installation and safety notices ........ 15
Positive connection ....................... 15
Switching positive ......................... 15
Fuse.............................................. 15
Negative (ground) connection ........ 15
Specifications ........................ 16
Features ........................................ 17
Connection diagrams ............. 72
10
GENERAL INFORMATION
General information
Thank you for choosing a Blaupunkt
product. We hope you enjoy using this
new piece of equipment.
Please read these operating instructions before using the equipment for
the first time.
The Blaupunkt editors are constantly
working on making the operating instructions clearer and easier to understand. However, if you still have any
questions on how to operate the device,
please contact your dealer or the telephone hotline for your country . You will
find the telephone number printed at the
back of this booklet.
We provide a manufacturer guarantee
for our products bought within the European Union. You can view the guarantee conditions at www.blaupunkt.de
or ask for them directly at:
Blaupunkt GmbH
Hotline
Robert Bosch Str. 200
D-31 139 Hildesheim
Installation and safety notices
Before connecting your signal controller, please read the following information carefully .
The battery’s negative terminal must
be disconnected for the entire time
it takes to install and connect this device.
When doing so, observe the vehicle
manufacturer’s safety notices (airbags,
alarm systems, trip computers, immobilizers).
Before drilling any holes, make sure that
no installed cables or vehicle components can be damaged.
When installing the signal controller,
select a location in the vehicle that allows you to attach it firmly into place
using screws. The installation location
should be such that the signal controller does not get in the way of the driver
and cannot endanger the occupants in
the event of the vehicle suddenly coming to a halt, for instance, during an
emergency stop.
The IR remote control should not be installed within the inflation range of airbags (driver, passenger side, side airbags) or in any position where it could
be struck by the vehicle occupants’
heads or knees.
With regard to the installation location
and the attachment using an adhesive
pad, check and ensure that the holding
strength of the installation surface is
sufficient and suitable for all situations
and safety requirements.
Accessories
We recommend you use accessories
that have been approved by Blaupunkt.
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
11
DANSK
SUPPLIED PARTS
SWITCHING ON/OFF
Supplied parts
The signal controller is supplied with all
the parts listed below. Please check that
the range of parts supplied with your
device is complete. If one of the listed
parts is missing, please contact your
dealer immediately.
● Signal controller 7 607 003 551
● Connecting cable
● Screws
● IR remote control
Switching on/off
Switching on the signal
controller
The signal controller is switched on via
the “+12V ignition” switching line by the
connected control device.
Switching off the signal
controller
The signal controller is switched off via
the “+12V ignition” switching line by the
connected control device.Switching on/
off.
● IR receiver
● Operating and installation instruc-
tions
12
SETTINGS
IR REMOTE CONTROL
Settings
External monitor switch (Fig. 2)
Switch position on right: No external
monitor connected.
Switch position on left: If a Blaupunkt
navigation (RGB) monitor is connected
via a Y-cable (7 607 001 600).
Monitor connections
Note: From the FRONT, LEFT , RIGHT
and OVERHEAD monitor output, you
can optionally assign the 8 or 13 PIN
jack.
IR remote control
Functions
The supplied remote control is suitable
for operating the signal controller and
the monitors.
You must enter a button combination
in order to control a single monitor
or all the monitors simultaneously.
To do so, you first select the monitor
(FRONT/LEFT/RIGHT-OVERHEAD or
ALL) and then the function that you
require. The selected monitor or
monitors remain(s) selected until you
press one of the buttons (FRONT/
LEFT/RIGHT-OVERHEAD or ALL)
again.
1
<
;
:
9
8
POWER
BOOSTER
FRONT
LEFT
NAVI
AUDIO CH
ALL
VOL CH
RIGHT
MUTE
4
5
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
OVERHEAD
7
IVRC 05
PORTUGUÊS
DANSK
13
IR REMOTE CONTROL
1 POWER
On/off button for the selected
monitor or monitors.
2 NAVI
Selects the navigation monitor.
3 VOL • arrow button
Increase the volume for the selected monitor (not Audio OUT).
VOL • arrow button
Decrease the volume for the selected monitor (not Audio OUT).
4 MUTE
Mute the volume for all the connected monitors and Audio OUT.
5 CH • arrow button
Select the input source for the selected monitor.
6 RIGHT
Selects the right monitor.
7 OVERHEAD
Selects the overhead monitor.
8 ALL
Select all monitors.
9 LEFT
Select the left monitor.
: FRONT
Select the front monitor.
/
Settings for Audio OUT
; AUDIO CH • Arrow button /
Select the input source for Audio
OUT.
Note: The volume of the input
source must be adjustable.
< BOOSTER
Setting the amplification for Audio
/
OUT
0 dB or 10 dB.
14
INSTALLATION
Installation
Installation and safety notices
Before connecting your signal controller, please read the following information carefully .
The battery’s negative terminal must
be disconnected for the entire time it
takes to install and connect this device.
When doing so, observe the vehicle
manufacturer’s safety notices (airbags,
alarm systems, trip computers, immobilizers).
Before drilling any holes, make sure that
no installed cables or vehicle components can be damaged.
When installing the signal controller,
select a location in the vehicle that allows you to attach it firmly into place
using screws. The installation location
should be such that the signal controller does not get in the way of the driver
and cannot endanger the occupants in
the event of the vehicle suddenly coming to a halt, for instance, during an
emergency stop.
The IR remote control should not be installed within the inflation range of airbags (driver, passenger side, side airbags) or in any position where it could
be struck by the vehicle occupants’
heads or knees.
With regard to the installation location
and the attachment using an adhesive
pad, check and ensure that the holding
strength of the installation surface is
sufficient and suitable for all situations
and safety requirements.
Note:
Before connecting the monitors to
your signal controller, check that the
+/- and switching positive connections are working properly .
Positive connection
Connect the fuse holder (1A fuse) to
protect the positive cable (permanent
(1), see Fig. 1). The fuse holder should
be connected to the positive terminal at
a distance of max. 30 cm from the vehicle battery (if necessary, drill a hole in
the bulkhead and use the appropriate
cable grommets).
Switching positive
Connect the switching positive cable (2)
(see Fig. 1) to the switching positive
output (ignition
) of the main device (e.g. car radio or navigation device).
If connecting to terminal 15 of the vehicle, protect the switching positive cable
(2) by installing a fuse holder (1A fuse)
at a maximum distance of 20 c m from
the point of connection.
Fuse
If the fuse needs to be replaced, never
bypass/bridge the fuse and never replace it with fuse types that are designed
for higher currents.
Negative (ground) connection
Attach the negative cable (1) (earth/
GND, (3), see Fig. 1) directly to the vehicle body using a screw. Scratch the
surface down to the bare metal at the
point at which the ground is made.
• If the installation requires holes to be
drilled or any other changes to be
15
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
ESPAÑOL
PORTUGUÊS
DANSK
INSTALLATION
SPECIFICATIONS
made to the vehicle, please contact
a specialist workshop in your area.
Note:
You cannot display PAL video on the
wide vision TV monitor using the RGB
input.
In this case, the P AL video signal must
be connected directly to the AV input of
the wide vision TV monitor ..
Specifications
Video input:
Composite Video, 1.0 Vpp, 75 ohms
Audio input:
0 - 1.0 Vrms, 20 Hz-20 kHz
(Booster off)
0 - 0.3 Vrms, 20 Hz-20 kHz
(Booster on)
RGB input (video signal):
0.7 VPP, 75 ohms
RGB input (composite-sync):
0.7 VPP, 75 ohms
Video output:
Composite video, 1.0 Vp-p, 75 ohms
Audio output:
0 - 1.0 Vrms, 20 Hz - 20 kHz
RGB output (video signal):
0.7 VPP, 75 ohms
RGB output (composite-sync):
1.0 VPP, 75 ohms
Power supply:
DC 12V , +/- 10%, max. 5A
Operating temperature:
-20° to +70° Celsius
Dimensions:
205 x 45 x 146 mm (W x H x D)
16
Features
5 Audio inputs:
Cinch jacks
4 Video inputs:
Cinch jacks
1 RGB input:
15 pin Sub-D socket
4 monitor outputs:
Composite video, audio L/R, control,
13-pin (8-pin) jack, with power, earth
and switching positive
1 RGB output:
15-pin Sub-D plug-type connector
1 Audio output:
Cinch jacks
10dB booster on/off
Conversion:
RGB to CCVS
CCVS to RGB
IR remote control
IR receiver
Power input:
4-pin plug-type connector
Metal housing
SPECIFICATIONS
DEUTSCH
ENGLISH
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
17
ESPAÑOL
PORTUGUÊS
DANSK
Anschlussbilder • Connection diagrams • Schéma
électrique • Schemi di allacciamento • Aansluittekeningen •
Anslutningsbilder • Esquemas de conexión • Esquemas de
ligação • Tilslutningsskemaer
12V
Fig. 1
IR
CH1 CH3
+12V Ignition
DC 12V IN
CH4CH2
(2)
Ext-monitor
CH5
RGB-IN AUDIO-IN
+12V Permanent
(Batterie, battery)
(1)
72
(3)
Masse / GND
Fig. 2
Audio in-right
Audio in-left
CH1 CH3
CH4CH2
Video in
Externer Monitorschalter
DC 12V IN
Ext-monitor
RGB-IN AUDIO-IN
IR-Empfänger (Eingang)
IR receiver in
DEUTSCH
IR
CH5
ENGLISH
FRANÇAIS
Fig. 3
FRONT LEFT OVERHEAD
MONITOR
○○○○○○○○
MONITOR
IVMS 5802
IVMS 6502
IVMR 9002
IVMR 1042
RIGHT
MONITOR
RGB OUT
MONITOR
○○○○○○○○
Audio OUT
RL
(right)
Audio OUT
Navi- Monitor
ITALIANO
NEDERLANDS
SVENSKA
(left)
ESPAÑOL
PORTUGUÊS
DANSK
73
Speakers
Video 1
Audio L 1
Audio R 1
Video 2
Audio L 2
Audio R 2
Video 3
Audio L 3
Audio R 3
Video 4
Audio L 4
Audio R 4
Signal Controller IVSC-5502
Preamp
out
Car Radio
2x Aux-in
Amplifier
Anschlusskabel/Additional Cables:
1
RCA-Cable 7 607 885 093 (1,3m)
7 607 886 093 (5m)
2
RGB-Y-Cable 7 607 001 600
3
C1-4x Cinch 7 607 893 093 (0,35m)
4
AUX 2-in 7 607 001 508
5
RGB-Cable 7 607 001 601 (1,5)
7 607 001 602 (4m)
1
1
in
4
3
AUX 2
CDC
in
Audio
M 3
M 2
M 1
DVD - Player (IVDP-01)
Video out
AV
in
Digital
out
Audio L out
Audio R out
CDC-A08
IDC-A09
CDC
out
2
1
M 4
Left
Monitor
Right
Monitor
Overhead
Monitor
Front
Monitor
OUT
RGB
OUT
RGB
IN
Audio
IN
5
IVMS 5802/6502
IVMR 9002/1024
DX-N/V
RGB
out
Video
in
DX-N/V
Monitor
1
s
h various component
ion example wit
Connect
Beispielanschluss mit verschiedenen Komponenten /
74
Service-Nummern / Service numbers / Numéros du service aprèsvente / Numeri del servizio di assistenza / Servicenummers /
Telefonnummer för service / Números de servicio / Números de
serviço / Servicenumre
Country: Phone: Fax: WWW:
Germany (D) 0180-5000225 05121-49 4002 http://www.blaupunkt.com
Austria (A) 01-610 390 01-610 393 91
Belgium (B) 02-525 5454 02-525 5263
Denmark (DK) 44 898 360 44-898 644
Finland (FIN) 09-435 991 09-435 99236
France (F) 01-4010 7007 01-4010 7320
Great Britain (GB) 01-89583 8880 01-89583 8394
Greece (GR) 210 57 85 350 210 57 69 473
Ireland (IRL) 01-4149400 01-4598830
Italy (I) 02-369 6331 02-369 6464
Luxembourg (L) 40 4078 40 2085
Netherlands (NL) 023-565 6348 023-565 6331
Norway (N) 66-817 000 66-817 157
Portugal (P) 01-2185 00144 01-2185 11111
Spain (E) 902-120234 916-467952
Sweden (S) 08-7501500 08-7501810
Switzerland (CH) 01-8471644 01-8471650
Czech. Rep. (CZ) 02-6130 0441 02-6130 0514
Hungary (H) 01-333 9575 01-324 8756
Poland (PL) 0800-118922 022-8771260
Turkey (TR) 0212-3350677 0212-3460040
USA (USA) 800-2662528 708-6817188
Brasil
(Mercosur) (BR) +55-19 3745 2769 +55-19 3745 2773
Malaysia
(Asia Pacific) (MAL) +604-6382 474 +604-6413 640
Blaupunkt GmbH
07/03 CM/PSS - 8 622 403 778
Loading...