Black & Decker PI100BB User Manual

SAFETY GUIDELINES / DEFINITIONS

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious

injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or

moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not

avoided, may result in property damage.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should

always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification
of tools or equipment could result in serious injury and property damage. There are certain applications
for which tools and equipment are designed. Black & Decker strongly recommends that this product NOT
be modified and/or used for any application other than for which it was designed. Read and understand
all warnings and operating instructions before using any tool or equipment.

IMPORTANT SAFETY INSTRUCTIONS

GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL APPLIANCES

READ ALL INSTRUCTIONS

WARNING: Read all instructions before operating product. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious injury.

• AVOID DANGEROUS ENVIRONMENTS. Donʼt use appliances in damp or wet locations. Donʼt use

appliances in the rain.

• STORE IDLE APPLIANCES INDOORS. When not in use, appliances should be stored indoors in dry,

and high or locked-up place – out of reach of children.

• DONʼT FORCE APPLIANCE. It will do the job better and with less likelihood of a risk of injury at the

rate for which it was designed.

• USE RIGHT APPLIANCE. Do not use the appliance for any job except that for which it is intended.

• DISCONNECT APPLIANCES. Disconnect the appliance from the power supply when not in use,

before servicing, and when changing accessories such as blades and the like.

• PROPER COOLING IS ESSENTIAL WHEN OPERATING THE INVERTER. Do not place the unit near

the vehicleʼs heat vent or in direct sunlight.

• USE OF ACCESSORIES AND ATTACHMENTS. The use of any accessory or attachment not
recommended for use with this appliance could be hazardous. Note: Refer to the accessory section of
this manual for further details.

• CHECK DAMAGED PARTS. A part that is damaged should be properly repaired or replaced by an
authorized service center.

• OUTDOOR USE EXTENSION CORDS. When an appliance plugged into this unit is used outdoors,
use only extension cords intended for use outdoors and so marked. NOTE THAT THIS INVERTER IS
NOT INTENDED TO BE USED OUTDOORS.

• EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension
cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord
will cause a drop in line voltage resulting in loss of power and overheating. The following table shows
the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier the cord.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK:

• Do not connect to AC distribution wiring.

• Do not make any electrical connections or disconnections in areas designated as IGNITION
PROTECTED. This includes DC cigarette lighter type plug connection or airplane adapter. This unit is
NOT approved for ignition protected areas.

• NEVER immerse the unit in water or any other liquid, or use when wet.

• Do not insert foreign objects into the AC outlet or the USB outlet.

WARNING: TO REDUCE THE RISK OF FIRE:

• Do not operate near flammable materials, fumes or gases.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

(0-7.6m) (7.6-15.2m) (15.2-30.4m) (30.4-45.7m)

240V 0-50 51-100 101-200 201-300

(0-15.2m) (15.2-30.4m) (30.4-60.9m) (60.9-91.4m)

Ampere Rating

More Not more American Wire Gauge
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

• DO NOT expose to extreme heat or flames.

CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:

• Remove appliance plug from outlet before working on the appliance.

• DO NOT attempt to connect or set up the unit or its components while operating your vehicle. Not pay­ing attention to the road may result in a serious accident.

• Always use the inverter where there is adequate ventilation. Do not block ventilation slots.

• ALWAYS turn the inverter OFF by disconnecting it from the DC accessory outlet when not in use.

• Make sure the nominal powering voltage is 12 volts DC, center connection positive (+).

• When using this unit in a vehicle, check the vehicle operaterʼs manual for maximum power rating and
recommended output. Do not install in engine compartment — install in a well ventilated area.

• Do not use with positive ground electrical systems.* Reverse polarity connection will result in a blown
fuse and may cause permanent damage to the inverter and will void warranty.

*The majority of modern automobiles, RVs and trucks are negative ground.

• Keep in mind that this inverter will not operate high wattage appliances or equipment that produce
heat, such as hair dryers, microwave ovens and toasters.

• Do not open the inverter — there are no user-serviceable parts inside.

• Do not use this inverter with medical devices. It is not tested for medical applications.

• Keep away from children. This is not a toy!

• Install and operate unit only as described in this Instruction Manual.

• Do not use this inverter on a watercraft. It is not qualified for marine applications.

• Check unit periodically for wear and tear. Take to a qualified technician for replacement of worn or
defective parts immediately.

• Read And Understand This Instruction Manual Before Using This Unit.

SAVE THESE INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF INJURY:

Follow these instructions and those published by battery manufacturer and the manufacturer of any
equipment you intend to use with this unit. Review cautionary markings on these products and on engine.

INTRODUCTION

Thank you for purchasing the PI100BB Power Inverter with USB Charging Port. This inverter can be
used to operate personal electronics and mobile office equipment, such as: laptop computers,
digital/video cameras, MP3 players, cell phones, PDAs, and more. It can also be used to recharge
110/120 volt AC devices that have an appropriate recharging adapter with a standard North American
two-or three-prong plug.

Please read this Instruction Manual carefully before use to ensure optimum performance and to avoid
damage to this product.

INCOMPATIBLE PRODUCTS:

CAUTION:

Certain products contain power supplies or circuits that are not compatible with a inverter using a modi­fied sine wave output (such as this inverter) and may be damaged by using this inverter.

If your product requires pure sine wave AC input power to function properly, the instruction manual for
your product could state this. If in doubt, you should contact your product manufacturer PRIOR TO USE.

Some products must be powered from a pure sine wave power source, such as standard household
power, or a “pure sine wave” inverter in order to function properly.

Your product could be damaged by this inverter if it contains:

1. Transformer type power supplies

2. Microprocessor controlled power supplies

3. Capacitive coupled power supplies

If an incompatible product is used with this inverter:

• The product might not operate at all, with no indication of failure. The product fuse might have opened
as a result of trying to use it with the inverter.

• The product exhibits unusual operation (such as, intermittent operation, buzzing, and the like.)

WARNING: If the product does not operate normally, to reduce the risk of injury or property

damage:

• Turn the product off immediately and unplug it from the inverter.

FEATURES

• 100 watts continuous output*

• 5 volt DC USB Charging Port

• Easiest inverter to use – truly plug and play

• Tri-color Power/Fault LED Indicator

• Compact, efficient and quiet

• Electronic circuit protection prevents damage due to overload/insufficient ventilation (overheat condition)

• Low-battery shutdown

*Refer to the “Specifications” section

Controls and Functions

HOW THIS INVERTER WORKS

This inverter is an electronic device that converts low voltage DC (direct current) electricity from a
battery to 115 volts AC (alternating current) household power. In designing this inverter, Black & Decker
has incorporated design techniques previously employed in computer power supplies. The result of
these design innovations is a smaller, lighter and easier-to-use power inverter.

The Power Inverter converts power in two stages. The first stage is a DC-to-DC conversion process that
raises the low voltage DC at the inverter input to 145 volts DC. The second stage is a MOSFET bridge
stage that converts the high voltage DC into 115 volts, 60 Hz AC.

The DC-to-DC inverter stage uses creative, high frequency, zero voltage switching power conversion
techniques that replace the bulky transformers found in less technologically advanced models. The
inverter stage uses advanced power MOSFET transistors in a full bridge configuration.

Power Inverter Output Waveform

NOTICE: THE OUTPUT OF THIS DEVICE IS NOT SINUSOIDAL. IT HAS A TOTAL HARMONIC

DISTORTION OF 38 PER CENT AND MAXIMUM SINGLE HARMONIC OF 32 PER CENT AT 25%
RATED LOAD.

The AC output waveform of this inverter is known as a modified sine wave. It is a stepped waveform that
has characteristics similar to the sine wave shape of utility power. This type of waveform is suitable for
most AC loads, including linear and switching power supplies used in electronic equipment,
transformers, and small motors.

The modified sine wave produced by this inverter has an RMS (root mean square) voltage of 115 volts.
Most AC voltmeters (both digital and analog) are sensitive to the average value of the waveform rather
than the RMS value. They are calibrated for RMS voltage under the assumption that the waveform
measured will be a pure sine wave. These meters will not correctly read the RMS voltage of a modified
sine wave. Non-TRUE RMS meters will read about 20 to 30 volts low when measuring the output of this
inverter. For accurate measurement of the output voltage of this unit, use a TRUE RMS reading
voltmeter such as a Fluke 87, Fluke 8080A, Beckman 4410 or Triplett 4200.

115 Volt AC Output

INSTRUCTION MANUAL

Catalog # PI100BB Form # 90565630 July 2010
Copyright © 2010 Black & Decker Printed in China

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.

100 WATT POWER

INVERTER WITH
USB CHARGING

PORT

Catalog Number
PI100BB

Thank you for choosing Black & Decker!

Go to www.BlackandDecker.com/NewOwner

to register your new product.

PLEASE READ BEFORE RETURNING THIS

PRODUCT FOR ANY REASON:

If you have a question or experience a problem with your Black & Decker purchase, go to

HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS

If you canʼt find the answer or do not have access to the internet,

call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. -- Fri. to speak with an agent.

Please have the catalog number available when you call.

for instant answers 24 hours a day.

12 VOLT DC VEHICLE ADAPTER
PLUG

POWER/FAULT
LED INDICATOR

THREE-PRONG 115 VOLT AC OUTLET

POWER PLUG ADJUSTS 90°

USB CHARGING PORT

CAUTION — RECHARGEABLE DEVICES

• Certain rechargeable devices are designed to be charged by plugging them directly into an AC recep­tacle. These devices may damage the inverter or the charging circuit.

• If there is any sign that your appliance is behaving differently to that when connected to the normal
power source then unplug and seek advice from your appliance manufacturer.

• This problem does not occur with most of the battery-operated equipment. Most of these devices use a
separate charger or transformer that is plugged into an AC receptacle.

• The inverter is capable of running most chargers and transformers.

OPERATING INSTRUCTIONS

The Power/Fault LED Indicator lights green when the inverter is properly connected to a functioning DC
power source. The AC and USB outlets are ready to use. (If the Power/Fault LED Indicator lights red,
refer to the Troubleshooting Section of this Instruction Manual.)

To turn the unit off, disconnect it from the 12 volt DC power source.
Always connect the inverter to the 12 volt DC power source before plugging any devices into the unit.
The standard North American 115 volt AC and USB outlets allow simultaneous operation of multiple

devices. Simply plug the equipment into the unit and operate normally. Ensure that the wattage of all

equipment simultaneously plugged into the inverter does not exceed 100 watts continuous.

Rated Versus Actual Current Draw of Equipment

Most electrical tools, appliances, electronic devices and audio/visual equipment have labels that indicate
the power consumption in amps or watts. Be sure that the power consumption of the item to be operat­ed is below 100 watts. If the power consumption is rated in amps AC, simply multiply by the AC volts
(115) to determine the wattage.

Resistive loads are the easiest for the inverter to run; however, it will not run larger resistive loads (such
as electric stoves and heaters), which require far more wattage than the inverter can deliver. Inductive
loads (such as TVs and stereos) require more current to operate than do resistive loads of the same
wattage rating.

For safety reasons, the unit will simply shut down if it is overloaded. To restart the unit, simply remove
the load, wait a few minutes, then plug it back in, rotating slightly to make sure there is good contact.

Operation of the 115 Volt AC Outlet - Figure A

1.Connect the unit to a vehicleʼs

accessory outlet or other 12 volt DC
power source. Make sure there is
adequate space for proper ventilation
of the inverter (figure A).

2.Rotate the unit slightly to make sure

there is good contact.

3.The Power/Fault LED Indicator will light

green, indicating a proper connection. If
the Power/Fault LED Indicator lights
red, a Fault condition exists. Refer to
the Troubleshooting Section of this
Instruction Manual.

4.If the inverter does not work, make sure

the ignition/accessory outlet is powering
the accessory outlet. Some vehicles
require the ignition switch to be turned
on.

5.Plug the (110/120 volt AC) appliance

into the inverterʼs three-prong AC outlet
and operate normally (figure A).

Notes: The inverter will not operate

appliances and equipment that
generate heat, such as hair
dryers, electric blankets, microwave
ovens and toasters.
Remember to disconnect the unit from any power source when it is not in use.

Operation of the USB Charging Port - Figure B

1.Connect the unit to a vehicleʼs accessory outlet or other 12 volt DC power source. Make sure there

is adequate space for proper ventilation
of the inverter (figure B).

2.Rotate the unit slightly to make sure

there is good contact.

3.The Power/Fault LED Indicator will light

green, indicating a proper connection. If
the Power/Fault LED Indicator lights
red, a Fault condition exists. Refer to
the Troubleshooting Section of this
Instruction Manual.

4.If the inverter does not work, make sure

the ignition/accessory outlet is powering
the accessory outlet. Some vehicles
require the ignition switch to be turned
on.

5.Plug the USB-powered device into the

inverterʼs USB Charging Port and oper­ate normally (figure B).

Note:This inverterʼs USB Charging Port

does not support data
communication. It only provides
5 volts DC/500 mA power to an
external USB-powered device.

Note: Not all mobile phones are provided

with a charging cable, they are
normally data cables which are not supported by this device - please check with your mobile
phone manufacturer for the correct charging cable. Remember to disconnect the unit from any
power source when it is not in use.

Protective Features

The inverter monitors the following conditions:
Low Battery Voltage — This condition is not harmful to the inverter, but could damage the power

source, so the inverter will automatically shut down when input voltage drops below 10.5 ± 0.3 volts DC.
Once the voltage recovers the inverter will auto restart.

Input Voltage Too High — The inverter will automatically shut down when DC input voltage exceeds

15.5 ± 0.3 volts, as this can harm the unit. Once the voltage recovers the inverter will auto restart.

Thermal Shutdown Protection — The inverter will automatically shut down when the unit becomes
overheated.

Overload/Short Circuit Protection — The inverter will automatically shut down when a short circuit
occurs.
Notes: The Power/Fault LED Indicator will light red to indicate a Fault condition before automatic

shutdown occurs.
If unit shuts down, disconnect it from the 12 volt DC power source, remove the load, wait a few
minutes, then plug it back in, rotating slightly to make sure there is good contact.

Operating Tips

The inverter should only be operated in locations that are:
DRY — Do not allow water or other liquids to come into contact with the inverter.
COOL — Surrounding air temperature should ideally be 10-20°C (50-68°F). Keep the inverter away from

direct sunlight, when possible.
WELL-VENTILATED — Keep the area surrounding the inverter clear to ensure free air circulation

around the unit. Do not place items on or over the inverter during operation. The unit will shut down if
the internal temperature gets too hot. The inverter will auto-reset after it cools down.

SAFE — Do not use the inverter near flammable materials or in any locations that may accumulate
flammable fumes or gases. This is an electrical appliance that can briefly spark when electrical
connections are made or broken.

CARE AND MAINTENANCE
Storage

1.Ideal storage temperature range is 0-40°C (32-104°F).

2.Store and use the inverter in a cool, dry place with adequate ventilation for all-around air circulation.

3.Avoid locations that are exposed to heating units, radiators, direct sunlight, or excessive humidity or
dampness.

See ‘Tools-

Electric’

– Yellow Pages –

for Service &

Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

A

B

LED Color

Possible Cause Recommendation

Flashing
Amber

Low input voltage Start Engine

Red

Battery voltage below

10.5 volts

Recharge battery or check DC power supply.

Red

Equipment being
operated draws too
much power

Reduce load to maximum 100 watts.

Red

Inverter in thermal
shutdown condition

Allow inverter to cool down. Ensure there is adequate
ventilation around the load is no more than 100 watts for
continuous operation.

Red

AC output is shorted Unplug the AC appliance. Disconnect the unit from any 12 volt

DC power source. Check the appliance cord. Refer to the
Service Information section that follows to contact a
Black & Decker Service Center.

Problem Explanation/Recommendation

Buzzing sound in audio
systems

Some inexpensive stereo systems and boom boxes make a buzzing
sound when operated from the inverter, because the power supply in
the electronic device does not properly filter the modified sine wave
produced by the
inverter

. The only solution to this problem is to use a sound system

that has a higher quality power supply.

Power/Fault LED Indicator

The Power / Fault LED Indicator has 3 states ;
Green - normal operation.
Flashing amber - low input voltage, AC output still on.
Red - Fault condition, AC output switched off. See the Protective Features Section of this Instruction

Manual and Fault Conditions in the following section.

TROUBLESHOOTING
Common Audio Problems

Fault Conditions

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you. To find
your local service location, refer to the yellow page directory under "Tools—Electric" or call:

1-800-544-6986 or visit www.blackanddecker.com

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom
it was purchased (provided that the store is a participating retailer). Returns should be made
within the time period of the retailerʼs policy for exchanges (usually 30 to 90 days after the
sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required. Black & Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and
you may have other rights which vary from state to state or province to province. Should you
have any questions, contact the manager of your nearest Black & Decker Service Center.
This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, check country specific warranty information contained in the
packaging, call the local company or see the website for warranty information.

SPECIFICATIONS

Output Power: 100 watts continuous
DC Input: 13.8 volts DC, 8 amps
AC Output: 100 watt continuous output – 115V AC @13.8V DC, 60 Hz
USB Charging Port Output: 5 volts DC/500 mA
Fuse: 10 amp internal fuse
Output Waveform: Modified Sine Wave
Optimum Efficiency: >85%
Low Voltage Shutdown: <10.5 ± 0.3 volts input voltage
Operating Temperature: 10-20°C (50-68°F)
Storage Temperature: 0-40°C (32-104°F)
Operating/Relative Humidity: 5-95% non-condensing

NORMAS DE SEGURIDAD: DEFINICIONES

PELIGRO: Indica una situación de peligro inminente que, si no se evita, provocará la muerte o

lesiones graves.

ADVERTENCIA: Indica una situación de peligro potencial que, si no se evita, podría provocar la

muerte o lesiones graves.

PRECAUCIÓN: Indica una situación de peligro potencial que, si no se evita, provocará lesiones leves

o moderadas.
PRECAUCIÓN: Cuando se utiliza sin el símbolo de alerta de seguridad indica una situación de peligro

potencial que, si no se evita, puede provocar daños a la propiedad.
RIESGO DE OPERACIÓN INSEGURA. Cuando se utilizan herramientas o equipos, siempre se deben

respetar las precauciones de seguridad para reducir el riesgo de lesiones personales. La operación, el
mantenimiento o la modificación incorrectos de herramientas o equipos pueden provocar lesiones
graves y daños a la propiedad. Las herramientas y los equipos están diseñados para determinados
usos. Black & Decker recomienda enfáticamente que NO se modifique este producto y que NO se util­ice para ningún otro uso que aquél para el que fue diseñado. Lea y comprenda todas las instrucciones
operativas y las advertencias antes de utilizar cualquier herramienta o equipo.

INSTRUCCIONES IMPORTANTES

SOBRE SEGURIDAD

ADVERTENCIAS E INSTRUCCIONES DE SEGURIDAD GENERALES PARA TODAS LAS

HERRAMIENTAS

LEA TODAS LAS INSTRUCCIONES

ADVERTENCIA: Lea todas las instrucciones antes de operar el producto. El incumplimiento de todas

las instrucciones enumeradas a continuación puede provocar una descarga eléctrica, un incendio o
lesiones graves.

• EVITE LAS CONDICIONES AMBIENTALES PELIGROSAS. NO utilice artefactos en zonas húmedas

o mojadas. No utilice artefactos bajo la lluvia.

• GUARDE LOS ARTEFACTOS QUE NO UTILICE EN EL INTERIOR. Cuando no los utilice, los artefac-

tos deben guardarse en el interior en un lugar seco, alto o bajo llave, lejos del alcance de los niños.

• NO FUERCE EL APARATO. Trabajará mejor y con menos probabilidad de riesgo de daños si se opera

a la velocidad para la que fue diseñado.

• UTILICE EL APARATO ADECUADO. Nunca utilice el aparato para otra tarea que no sea aquella para

la que fue creada.

• DESCONECTE LOS APARATOS. Desconecte el aparato de la fuente de energía cuando no lo utiliza,

antes de realizar un mantenimiento y al cambiar accesorios como hojas y elementos semejantes.

• EL ENFRIAMIENTO CORRECTO ES FUNDAMENTAL AL OPERAR EL CONVERSOR. No coloque

la unidad cerca de los orificios de ventilación del vehículo ni la exponga a la luz solar directa.

• USO DE SUPLEMENTOS Y ACCESORIOS. El uso de accesorios o dispositivos no recomendados para
este aparato puede resultar peligroso. Nota: Consulte la sección "Accesorios" de este manual para
obtener detalles adicionales.

• VERIFIQUE QUE NO HAYA PIEZAS DAÑADAS. Una pieza se daña que se debe reparar o substituir
correctamente por un centro de servicio autorizado.

• EN ESPACIOS ABIERTOS, USE CABLES PROLONGADORES. Cuando una aplicación tapada en
esta unidad se utiliza al aire libre, utilice solamente las cuerdas de la extensión previstas para el uso al
aire libre y así que marcado. OBSERVE QUE ESTE INVERSOR NO ESTÁ PENSADO PARA SER UTI­LIZADO AL AIRE LIBRE.

• CABLES PROLONGADORES. Asegúrese de que el cable prolongador esté en buenas condiciones.
Cuando utilice un cable prolongador, cerciórese de que tenga la capacidad para conducir la corriente
que su producto exige. Un cable de menor capacidad provocará una disminución en el voltaje de la
línea, lo cual producirá una pérdida de potencia y sobrecalentamiento. La siguiente tabla muestra la
medida correcta que debe utilizar según la longitud del cable y la capacidad nominal en amperios indi­cada en la placa. En caso de duda, utilice el calibre inmediatamente superior. Cuanto menor es el
número de calibre, más grueso es el cable.

ADVER-

TENCIA: PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA:

• No conecte al cableado de distribución de CA.

• No realice conexiones o desconexiones eléctricas en áreas designadas como PROTEGIDAS CONTRA
IGNICIÓN. Esto incluye el adaptador para aviones o el enchufe tipo encendedor de cigarrillos de CC.
Esta unidad NO está aprobada para áreas protegidas contra ignición.

• NUNCA sumerja la unidad en el agua ni en ningún otro líquido, ni la utilice cuando esté húmeda.

• No introduzca objetos extraños en el tomacorriente de CA ni en el puerto USB.

ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO:

• No opere cerca de materiales, vapores o gases inflamables.

• NO lo exponga al calor extremo o a las llamas.

PRECAUCIÓN: PARA REDUCIR EL RIESGO DE LESIONES O DAÑO A LA PROPIEDAD:

• Quite el enchufe de la aplicación del enchufe antes de trabajar en la aplicación.

• NO intente conectar o configurar la unidad o sus componentes mientras maneja su vehículo. El hecho
de no prestar atención a la carretera puede tener como consecuencia un accidente grave.

• Siempre utilice el conversor en lugares adecuadamente ventilados. No bloquee las ranuras de
ventilación.

• SIEMPRE APAGUE el conversor desenchufándolo del tomacorriente para accesorios de CC cuando
no lo utilice.

• Asegúrese de que el voltaje nominal de encendido sea CC de 12 voltios, conexión central positivo (+).

• Al utilizar esta unidad en un vehículo, revise el manual del usuario del vehículo para ver el máximo
rango de potencia y la salida recomendada. No lo instale en el compartimiento del motor. Instálelo en
un área bien ventilada.

• No lo utilice con sistemas eléctricos con positivo a tierra*. La conexión de polaridad inversa hará que
un fusible se queme y puede causar un daño permanente al conversor y anulará la garantía.
*La mayoría de los automóviles, vehículos recreativos y camiones modernos posee un negativo a
tierra.

• Tenga en cuenta que este conversor no funcionará con aparatos o equipos de alta potencia en vatios
que produzcan calor, como secadores de cabello, hornos de microondas y tostadores.

• No abra el conversor: no hay piezas que el usuario pueda reparar en su interior.

• No utilice este conversor con dispositivos médicos. No se ha comprobado su funcionamiento en
aplicaciones médicas.

• Mantenga fuera del alcance de los niños. ¡Esto no es un juguete!

• Instale y opere la unidad solamente como se describe en este manual de instrucciones.

• No utilice este inversor en un watercraft. No se califica para los usos marinas.

• Controle el desgaste de la unidad periódicamente. Lleve la unidad a un técnico calificado para reem­plazar las piezas desgastadas o defectuosas de inmediato.

• Lea Y Entienda Este Manual De Instrucción Antes De Usar Esta Unidad.

CONSERVE ESTAS INSTRUCCIONES

ADVERTENCIA: PARA REDUCIR EL RIESGO DE LESIONES:

Siga estas instrucciones y las publicadas por el fabricante de la batería y de cualquier equipo que tenga
la intención de utilizar con esta unidad. Revise las indicaciones sobre precauciones en estos productos
y en el motor.

INTRODUCCIÓN

Gracias por comprar el conversor eléctrico PI100BB con puerto de carga USB. Este conversor puede
utilizarse para operar productos electrónicos personales, como: computadoras portátiles, cámaras digi­tales o filmadoras, reproductores de MP3, teléfonos celulares, agendas electrónicas y más. También
puede utilizarse para recargar dispositivos de CA de 110/120 voltios que tengan un adaptador de recarga
apropiado con un enchufe de dos o tres patas estadounidense estándar.

Lea este Manual de instrucciones detenidamente antes de utilizar la unidad para garantizar su óptimo
rendimiento y evitar dañar el producto.

PRODUCTOS INCOMPATIBLES:

PRECAUCIÓN:

Ciertos productos contienen fuentes de energía o circuitos que no son compatibles con los conversores
que utilizan una salida de onda senoidal modificada (como este conversor) y que pueden dañarse al
utilizar este conversor.

Si su producto requiere una alimentación de entrada de CA de onda senoidal pura para funcionar
correctamente, es posible que lo indique el manual de instrucciones de su producto. En caso de duda,
debe comunicarse con el fabricante de su producto ANTES DE UTILIZARLO.

Algunos productos deben alimentarse con una fuente de energía de onda senoidal pura, como la
energía estándar de uso doméstico o un conversor de “onda senoidal pura” para poder funcionar
correctamente.

Este conversor puede dañar su producto si éste contiene:

1. Fuentes de energía tipo transformador

2. Fuentes de energía controladas por microprocesador

3. Fuentes de energía con acoplamiento capacitivo

Si se utiliza un producto incompatible con este conversor:

• Es posible que el producto no funcione en absoluto, sin indicios de falla. Es posible que el fusible del
producto se haya abierto al intentar utilizarlo con el conversor.

• El producto presenta un funcionamiento anormal (como operación intermitente, zumbido y similares).

ADVERTENCIA: Si el producto no funciona normalmente, para reducir el riesgo de lesiones y

daños a la propiedad:

• Apague el producto de inmediato y desenchúfelo del conversor.

CARACTERÍSTICAS

• Salida continua de 100 vatios*

• Puerto de carga USB de CC de 5 voltios

• El conversor más fácil de utilizar: de verdad lo enchufa y funciona

• Luz indicadora LED tricolor de energía/falla

• Compacto, eficiente y silencioso

• Protección del circuito electrónico que evita daños por sobrecarga/ventilación insuficiente (sobrecalen­tamiento)

• Apagado por batería baja

*Consulte la sección “Especificaciones”

Controles y funciones

FUNCIONAMIENTO DEL CONVERSOR

El conversor es un dispositivo electrónico que convierte electricidad de CC (corriente continua) de bajo
voltaje de una batería a energía para uso doméstico de CA (corriente alterna) de 115 voltios. Durante el
diseño de este conversor, Black & Decker incorporó técnicas de diseño utilizadas anteriormente en
fuentes de energía para computadoras. El resultado de estas innovaciones en el diseño es un conversor
eléctrico más pequeño, más liviano y más fácil de utilizar.

El conversor eléctrico convierte energía en dos etapas. La primera etapa consiste en un proceso de
conversión de CC a CC que incrementa la CC de bajo voltaje en la entrada del conversor a CC de 145
voltios. La segunda etapa es una etapa puente MOSFET (transistor de efecto de campo semiconductor
de óxido metálico) que convierte la CC de alto voltaje a CA de 115 voltios, 60 Hz.

La etapa de conversión de CC a CC comprende técnicas de conversión por conmutación de energía
creativas, de alta frecuencia y cero voltaje, que reemplazan los grandes transformadores incluidos en
los modelos con tecnología menos avanzada. La etapa de conversión utiliza transistores eléctricos
MOSFET avanzados en una configuración de puente completa.

La forma de onda de salida del conversor eléctrico

AVISO: LA SALIDA DE ESTE DISPOSITIVO NO ES SINUSOIDAL. TIENE UNA DISTORSIÓN

ARMÓNICA TOTAL DE 38% Y UN ARMÓNICO ÚNICO MÁXIMO DE 32% A 25% DE LA CARGA NOM­INAL.

La forma de onda de la salida de CA de este conversor se conoce como una onda senoidal modificada.
Es una forma de onda escalonada que posee características similares a la forma de onda senoidal de
la electricidad. Este tipo de forma de onda es adecuado para la mayoría de las cargas de CA, incluidas
las fuentes de energía por conmutación y lineales utilizadas en equipos electrónicos, transformadores y
motores pequeños.La onda senoidal modificada producida por este conversor posee un voltaje RMS
(raíz cuadrada media) de 115 voltios. La mayoría de los voltímetros de CA (digitales y análogos) son
sensibles al valor promedio de la forma de onda en lugar de al valor RMS. Están calibrados para el
voltaje RMS suponiendo que la forma de onda medida será una onda senoidal pura. Estos medidores
no leerán correctamente el voltaje RMS de una onda senoidal modificada. Un medidor RMS no VER­DADERO leerá aproximadamente 20 a 30 voltios mínimo cuando mida la salida de este conversor.
Para realizar una medición adecuada del voltaje de salida de esta unidad, utilice un voltímetro de lec­tura RMS VERDADERO como un Fluke 87, Fluke 8060A, Beckman 4410 o Triplett 4200.

Salida de CA de 115 voltios

Calibre mínimo para los juegos de cables

Voltios Longitud total del cable en pies

120V 0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

240V 0-50 51-100 101-200 201-300

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

Capacidad nominal en amperios

Más No más Medida de conductor estadounidense
que que
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 No recomendado

CONSERVE ESTE MANUAL PARA FUTURAS CONSULTAS.

LEA EL MANUAL ANTES DE DEVOLVER

ESTE PRODUCTO POR CUALQUIER MOTIVO:

Si tiene una consulta o algún inconveniente con su producto Black & Decker, visite

HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS

Si no encuentra la respuesta o no tiene acceso a Internet, llame al 1-800-544-6986 de

lunes a viernes de 8 a.m. a 5 p.m. hora del Este para hablar con un agente.

Cuando llame, tenga a mano el número de catálogo.

para obtener respuestas instantáneas las 24 horas del día.

Gracias por elegir Black & Decker!

Visite www.BlackandDecker.com/NewOwner

para registrar su nuevo producto.

CONVERSOR ELÉCTRICO DE 100 VATIOS

CON PUERTO DE CARGA USB
MANUAL DE INSTRUCCIONES

ENCHUFE PARA ADAPTADOR DE
VEHÍCULO DE 12 VOLTIOS DE CC

INDICADOR LED DE
POTENCIA Y FALLAS
INTEGRADO

TOMACORRIENTE DE CA DE 115
VOLTIOS DE TRES CLAVIJAS

EL ENCHUFE SE AJUSTA A
90°

INDICADOR LED DE
POTENCIA Y FALLAS
INTEGRADO