Black & Decker KR5010V, KR5010 User Manual
ENRUUA
www.blackanddecker.ru
KR5010
KR5010V
ENGLISH
(Original instructions)
FIG. A
FIG. B
3
4
1
2
7
8
FIG. C
2
6
5
(Original instructions)
ENGLISH
Intended use
Your BLACK+DECKER™ KR5010,KR5010V
Impact Drill has been designed for drilling in
wood, metal and concrete. This tool is
intended for consumer use only
General safety rules
Warning! Read and understand all
instructions. Failure to follow all instructions
listed below, may result in electric shock,
fire and/or serious personal injury. lesiones
graves.
Save these instructions
Safety instructions
General power tool safety warnings.
Warning! Read all safety warnings
and all instructions. Failure to
follow the warnings and instructions
listed below may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for
future reference. The term “power tool” in
all of the warnings listed below refers to
your mains operated (corded) power tool or
battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away
while operating a power tool.
Distractions can cause you to lose
control.
2. Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified
plugs and matching outlets will reduce
risk of electric shock.
b. Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric
shock if your body is earthed or
grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
d. Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e. When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock. Note: The term “Residual Curent
Device (RCD)” can be replaced by
“Ground Fault Circuit Interrupter (GFCI)”
or by “Earth Leakage Circuit Breaker
(ELCB)”.
f. If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3. Personal safety
a. Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool
while you are tired or under the
influence of drugs, alcohol or
medication. A moment of inattention
while operating power tools may result in
serious personal injury.
b. Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure
the switch is in the o-position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your
finger on the switch or energising power
tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a
rotating part of the power tool may result
in personal injury.
3
ENGLISH
(Original instructions)
e. Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g. If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use of
dust collection can reduce dust-related
hazards.
4. Power tool use and care
a. Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b. Do not use the power tool if the switch
does not turn it on and o. Any power
tool that cannot be controlled with the
switch is dangerous and must be
repaired.
c. Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive
safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may aect the power
tools operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to bind
and are easier to control.
g. Use the power tool, accessories and tool
bits etc., in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations dierent from those intended
could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
Additional safety instructions for
hammer drill
• Wear ear protectors with impact drills.
Exposure to noise can cause hearing loss.
• Hold power tool by insulated gripping
surfaces when performing an operation
where the cutting tool may contact
hidden wiring or its own cord. Contact
with a “live” wire will also make exposed
metal parts of the power tool “live” and
shock the operator.
• Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by
hand or against your body leaves it
unstable and may lead to loss of control.
• Before drilling into walls, floors or ceilings
check for the location of wiring and
pipes.
• Avoid touching the tip of a drill bit just
after drilling, as it may be hot.
Vibration
The declared vibration emission values
stated in the technical data and the
declaration of conformity have been
measured in accordance with a standard test
method provided by EN 60745 and may be
used for comparing one tool with another.
The declared vibration emission value may
also be used in a preliminary assessment of
exposure.
Warning! The vibration emission value
during actual use of the power tool can
dier from the declared value depending on
the ways in which the tool is used. The
vibration level may increase above the level
stated.
4
(Original instructions)
ENGLISH
When assessing vibration exposure to
determine safety measures required by
2002/44/EC to protect persons regularly
using power tools in employment, an
estimation of vibration exposure should
consider, the actual conditions of use and
the way the tool is used, including taking
account of all parts of the operating cycle
such as the times when the tool is switched
o and when it is running idle in addition to
the trigger time.
Labels on tool
The label on your tool may include the
following symbols along with the date code:
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n0 ....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Reciprocation per
minute
Hz .......
Position of date barcode
The Date Code, which also includes the year
of manufacture, is printed into the housing.
Example:
2014 XX JN
Year of manufacturing
Electrical safety
Your tool is double insulated;
therefore no earth wire is required.
Always check that the main voltage
corresponds to the voltage on the
rating plate.
Warning! If the power cord is
damaged, it must be replaced by
the manufacturer, authorized
BLACK+DECKER Service Center or
an equally qualified person in order
to avoid damage or injury. If the
power cord is replaced by an
equally qualified person, but not
authorized by BLACK+DECKER, the
warranty will not be valid.
Features (Fig. A)
1. On/O switch
2. Lock-on button
3. Drilling mode selector
4. Chuck
Assembly
Warning! Before assembly, make sure that
the tool is switched o and unplugged.
Fitting a drill bit or screwdriver bit keyed
chuck (Fig. B)
• Open the chuck by turning the sleeve (5)
counterclockwise.
• Insert the bit shaft (6) into the chuck.
• Insert the chuck key (7) into each hole (8)
in the side of the chuck and turn
clockwise until tight.
Removing and refitting the chuck (Fig. C)
• Open the chuck as far as possible.
• Remove the chuck retaining screw,
located in the chuck, by turning it
clockwise using a screwdriver.
• Tighten an Allen key into the chuck and
strike it with a hammer as shown.
• Remove the Allen key.
• Remove the chuck by turning it
counterclockwise.
• To refit the chuck, screw it onto the
spindle and secure it with the chuck
retaining screw.
Use
Warning! Let the tool work at its own pace.
Do not overload.
Warning! Before drilling into walls, floors or
ceilings, check for the location of wiring and
pipes.
Selecting the direction of rotation
(Applicable for KR5010,KR5010V)
For drilling and for tightening screws, use
forward (clockwise) rotation. For loosening
screws or removing a jammed drill bit, use
reverse (counterclockwise) rotation.
• To select forward rotation, push the
Forward/Reverse slider to the centre
position.
5
ENGLISH
(Original instructions)
• To select reverse rotation, push the
Forward/Reverse slider to the left.
Warning! Never change the direction of
rotation while the motor is running.
Selecting the drilling mode
• For drilling in masonry, set the drilling
mode selector (4) to the position.
• For drilling in other materials and for
screwdriving, set the drilling mode
selector to the position.
Switching on and o
• To switch the tool on, press switch (1).
For variable speed units, the tool’s speed
depends on how far you press the
switch. As a general rule for variable
speed units, use low speeds for large
diameter drill bits and high speeds for
smaller diameter drill bits.
• For continuous operation, press the
lock-on button (2) and release the
variable speed switch. This option is
available only at full speed. This option
does not work in reverse rotation.
• To switch the tool off, release the switch.
To switch the tool o when in continuous
operation, press the variable speed
switch once more and release it.
Maintenance
Your tool has been designed to operate
over a long period of time with a minimum
of maintenance. Continuous satisfactory
operation depends upon proper tool care
and regular cleaning.
Warning! Before performing any
maintenance, switch o and unplug the tool.
• Regularly clean the ventilation slots in
your tool using a soft brush or dry cloth.
• Regularly clean the motor housing using
a damp cloth. Do not use any abrasive or
solvent-based cleaner.
Important! To assure product SAFETY and
RELIABILITY, repairs, maintenance and
adjustment (other than those listed in this
manual) should be performed by authorized
service centers or other qualified service
personnel, always using identical
replacement parts.
Accessories
The performance of your tool depends on
the accessory used. BLACK+DECKER
accessories are engineered to high quality
standards and designed to enhance the
performance of your tool. By using these
accessories you will get the very best from
your tool.
Service information
BLACK+DECKER oers a full network of
company-owned and authorized service
locations. All BLACK+DECKER Service
Centers are staed with trained personnel to
provide customers with ecient and reliable
power tool service. For more information
about our authorized service centers and if
you need technical advice, repair, or genuine
factory replacement parts, contact the
BLACK+DECKER location nearest you, or
visit us at www.BlackandDecker-la.com
Protecting the environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or if it is of no further use to you, do
not dispose of it with household waste. Make
this product available for separate collection.
Separate collection of used products and
packaging allows materials to be recycled
and used again. Reuse of recycled materials
helps prevent environmental pollution and
reduces the demand for raw materials.
Local regulations may provide for separate
collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
BLACK+DECKER provides a facility for the
collection and recycling of BLACK+DECKER
products once they have reached the end of
their working life. To take advantage of this
service please return your product to any
authorised repair agent who will collect
them on our behalf.
6
(Original instructions)
ENGLISH
You can check the location of your nearest
authorised repair agent by contacting your
local BLACK+DECKER oce at the address
indicated in this manual. Alternatively, a list
of authorised BLACK+DECKER repair
agents and full details of our after-sales
service and contacts are available on the
Internet at: www.2helpU.com.
Technical data
Power W 550 550
Voltage V 220-240 220-240
Frequency Hz 50/60 50/60
Chuck mm 10 10
No-load speed RPM 2900 0-2900
IPM - Blows per minute
ipm 47600 0-47600
Max drilling capacity
Steel/concrete mm 10 10
Wood mm 20 20
Weight kg 1.4 1.4
Level of sound pressure according to
EN 60745:
LpA (sound pressure) 101.6 dB(A), Uncertainty (K) 3 dB(A)
(sound power) 112.6 dB(A), Uncertainty (K) 3 dB(A)
L
WA
Vibration total values (triax vector sum) according to
EN 60745:
Drilling into metal (a
Impact drilling (a
) 4.6 m/s2, uncertainty (K) 1.5 m/s2
h, D
) 15.2 m/s2, uncertainty (K) 1.5 m/s2
h, ID
KR5010 KR5010V
EC declaration of conformity
MACHINERY DIRECTIVE
KR5010,KR5010V-Impact Drill
BLACK+DECKER declares that these
products described under "Technical data"
are in compliance with: 2006/42/EC,
EN 60745-1:2009 + A11:2010,
EN 60745-2-1:2010
These products also comply with Directive
EN 55014-1:2006 +A1:2009 +A2:2011,
EN 55014-2:1997 +A1:2001 +A2:2008,
EN 61000-3-2:2014, EN 61000-3-3:2013
2014/30/EU and 2011/65/EU.
For more information, please contact
BLACK+DECKER at the following address or
refer to the back of the manual.
The undersigned is responsible for
compilation of the technical fi le and makes
this declaration on behalf of
BLACK+DECKER.
R. Laverick
Engineering Manager
BLACK+DECKER Europe, 210 Bath Road,
Slough,
Berkshire, SL1 3YD
United Kingdom
10.2015
7
ENGLISH
(Original instructions)
Guarantee
BLACK+DECKER is confident of the quality
of its products and oers an outstanding
guarantee. This guarantee statement is in
addition to and in no way prejudices your
statutory rights.
If a BLACK+DECKER product becomes
defective due to faulty materials,
workmanship or lack of conformity, within
24 months from the date of purchase,
BLACK+DECKER guarantees to replace
defective parts, repair products subjected to
fair wear and tear or replace such products
to make sure of the minimum inconvenience
to the customer unless:
• The product has been used for trade,
professional or hire purposes.
• The product has been subjected to
misuse or neglect.
• The product has sustained damage
through foreign objects, substances or
accidents.
• Repairs have been attempted by persons
other than authorised repair agents or
BLACK+DECKER service sta.
To claim on the guarantee, you will need to
submit proof of purchase to the seller or an
authorised repair agent. You can check the
location of your nearest authorised repair
agent by contacting your local
BLACK+DECKER oce at the address
indicated in this manual. Alternatively, a list
of authorised BLACK+DECKER repair agents
and full details of our aftersales service and
contacts are available on the Internet at:
www.2helpU.com
8
Loading...