Black & Decker GL670P, GL670, GL650 User Manual

GL650 GL660
GL660P
GL670
GL670P
1
English 8
Svenska 16
Norsk 23
Dansk 30
Suomi 37
Copyright Black & Decker
2
2 3
5 7
12 14
1513
8 9 10 11
1 4
8
5 6 7
32
8 4 1
12 15
1413
8 9 10 11
3
16
11
19
19
17 18 20
CB
D
4
20
°
7
FE
7
5
G
6
H
5
D
A
I
21
24
22
10 11
C
B
J
25
1223
26
K
6
25
L
28
27 27
M
27 27
N
O P
7
ENGLISH
GRASS TRIMMER GL650/GL660/GL660P/GL670/GL670P
CONGRATULATIONS!
You have chosen a Black & Decker tool. Our aim is to provide quality tools at an affordable price. We hope that you will enjoy using this tool for many years.
EC DECLARATION OF CONFORMITY
GL650/GL660/GL660P/GL670/GL670P Black & Decker declares that these products conform to: 98/37/EC, 89/336/EEC, 73/23/EEC, EN 60335, EN 55014, EN 61000
Level of sound pressure, measured according to 84/538/EEC:
GL650 GL660 GL670
L
(sound pressure) dB(A) 83 83 83
pA
LWA(acoustic power) dB(A) 96 96 96
GL660P GL670P
Always wear ear protection if the sound pressure exceeds 85 dB(A).
Hand/arm weighted vibration value according to 98/37/EC:
GL650 GL660 GL660P GL670 GL670P
< 2.5 m/s2< 2.5 m/s2< 2.5 m/s2< 2.5 m/s2< 2.5 m/s
2
Brian Cooke
Director of Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
8
INTENDED USE
Your Black & Decker grass trimmer GL650/GL660/ GL660P/GL670/GL670P has been designed for trimming and finishing lawn edges and to cut grass in confined spaces. This tool is intended for consumer use only.
SAFETY INSTRUCTIONS
Warning symbols
The following symbols are used in this manual:
Denotes risk of personal injury, loss of life or damage to the tool in case of non­observance of the instructions in this manual.
Denotes risk of electric shock.
Read the manual prior to operation.
Know your appliance
Warning! When using mains-powered
appliances, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock and personal injury.
Read all of this manual carefully before
operating the appliance.
Before operating the appliance, make
sure that you know how to switch it off in an emergency.
The intended use is described in this
manual. The use of any accessory or attachment or performance of any operation with this appliance other than those recommended in this instruction manual may present a risk of personal injury.
Retain this manual for future reference.
ENGLISH
Work area
Do not expose the appliance to rain. Do not
use the appliance in damp or wet conditions.
Only use the appliance in daylight or good
artificial light.
Personal protection
Wear stout shoes or boots to protect your feet.
Do not operate the appliance wearing open­toed sandals or when barefoot.
Wear long trousers to protect your legs.
Using your appliance
Be sure that the appliance is switched off when
plugging in.
Stay alert. Watch what you are doing.
Use common sense.
Do not operate the appliance when you are
tired.
If the appliance begins to vibrate abnormally,
switch it off and remove the plug from the socket. Allow rotating parts to stop and inspect the appliance for damage and loose parts.
Never pull the cord to disconnect the plug
from the socket. Keep the cord away from heat, oil and sharp edges.
If the mains cable is damaged during use,
switch the appliance off and disconnect the plug from the mains immediately. Do not
touch the mains cable before disconnecting from the mains.
Safety of others
Do not allow children or any person unfamiliar
with these instructions to operate the appliance.
Do not allow children, visitors or animals to
come near the work area or to touch the appliance or mains cable.
Remember that the operator may be held
responsible for accidents or hazards occurring to other people or their property.
After use
Switch off, remove the plug from the socket
and ensure that moving parts have stopped rotating before leaving the appliance unattended and before changing, cleaning or inspecting any parts of the appliance.
When not in use, the appliance should be
stored in a dry place. Children should not have access to stored appliances.
Inspection and repairs
Before use, check the appliance for damaged
or defective parts. Check for misalignment and seizure of moving parts, breakage of parts, damage to guards and switches and any other conditions that may affect its operation.
Do not use the appliance if any part is damaged
or defective. Do not use the appliance if the switch does not turn it on and off.
Never use the appliance when any guard or
enclosure is damaged or not in place.
Ensure that the appliance will operate properly
and perform its intended function.
Have any damaged or defective parts repaired
or replaced by an authorised repair agent.
Before use, check the mains cable for signs of
damage, ageing and wear.
Do not use the appliance if the mains cable is
damaged or defective.
If the mains cable is damaged or defective it
must be repaired by an authorised repair agent to avoid a hazard.
Never attempt to remove or replace any parts
other than those specified in this manual.
Additional safety instructions for grass trimmers
The following warning symbols are found on the appliance:
Wear safety glasses or goggles when operating this tool.
The cutting line will continue to run for a few seconds after switching the appliance off. Never attempt to force the line to come to a standstill.
360˚
6m/20ft
Keep people and animals at least 6 m away from the cutting area.
Do not expose the appliance to rain or high humidity.
9
ENGLISH
Switch off, remove the plug from the socket and ensure that moving parts have stopped rotating before leaving the appliance unattended and before changing, cleaning or inspecting any parts of the appliance.
Before using the appliance, check that your
cutting path is free from sticks, stones, wire and any other objects.
Only use the appliance in the correct position,
with the cutting line near the ground, as shown in the illustrations. Never switch the appliance on in any other position.
Switch on the appliance only when hands and
feet are away from the cutting line.
Avoid body contact with the cutting line while
the appliance is running.
Do not work on steep slopes. Be sure of your
footing. Be aware that freshly cut grass is damp and slippery.
Take care when trimming near borders and
gravel paths or roads, as stones and soil may be moved by the cutting line.
Do not put the appliance down until the
cutting line has come to a complete standstill.
Use only the appropriate type of
Black & Decker cutting line. Never use metal cutting line or fishing line.
Take care to avoid injury from the line
trimming blade. Do not touch the blade. After extending new cutting line, always return the appliance to its normal operating position before switching on.
Take care to keep the mains cable away from
the cutting line. Always be aware of the position of the cable.
ELECTRICAL SAFETY
The appliance has been designed for one voltage only. Always check that the power supply corresponds to the voltage on the rating plate.
This appliance is designed for use on AC (mains) power supplies only. Do not attempt to use on any other supply.
This appliance is double insulated in accordance with EN 60335; therefore no earth wire is required.
Prevent body contact with earthed or
grounded surfaces (e.g. metal railings, lamp-posts etc.).
Electric safety can be further improved by
using a high-sensitivity (30 mA / 30 mS) residual current device (RCD).
Mains plug replacement (U.K. & Ireland only)
Should your mains plug need replacing and you
are competent to do this, proceed as instructed below. If you are in doubt, contact an authorised repair agent or a qualified electrician.
Disconnect the plug from the supply and
remove the fuse from the plug.
Cut off the plug and dispose of it safely; a plug
with bared copper conductors is dangerous if engaged in a live socket outlet.
Only fit 13 Amperes BS1363A approved plugs
fitted with the correctly rated fuse (1). Use 5 Amperes fuses.
The cable wire colours, or a letter, will be marked
at the connection points of most good quality plugs. Attach the wires to their respective points in the plug (see above). Brown is for Live (L) (2), blue is for Neutral (N) (4).
Before replacing the top cover of the mains
plug ensure that the cable restraint (3) is holding the outer sheath of the cable firmly and that the leads are correctly fixed at the terminal screws.
If the plug has a fuse cover, make sure that the
fuse cover is fitted. Do not use the plug if the fuse cover is missing or damaged.
10
Never use a light socket.
Using an extension cable
Always use an approved extension cable suitable for the power input of this appliance (see rating plate). The extension cable must be suitable for outdoor use.
Before use, inspect the cable for signs of
damage, wear and ageing. Replace the extension cable if damaged or defective.
When using a cable reel, always unwind the
cable completely.
Take care to keep the cable away from the
cutting line. Always be aware of the position of the cable.
CARTON CONTENTS
The carton contains: 1 Grass trimmer 1 Guard with mounting screw 1 Plant protector incl. parts pack
(GL660P/GL670P only)
1 Instruction manual
Carefully unpack all parts.
OVERVIEW (fig. A)
1. On/off switch
2. Handle
3. Cable restraint
4. Power inlet (not for UK)
5. Secondary handle
6. Handle button (GL670/GL670P)
7. Locking ring
8. Cable storage hooks
9. Motor housing
10. Pedal (GL670/GL670P)
11. Guard
12. Line trimming blade
13. Edge guide
14. Spool housing
15. Cutting line
ENGLISH
Fitting the guard (fig. B)
Unplug the tool.
Remove the screw (16) from the housing.
Place the guard (11) onto the tool as shown.
Firmly press the guard until it snaps into place.
Secure the guard with the screw (16).
Never use the tool unless the guard is properly fitted.
Releasing the cutting line (fig. A)
In transit, the cutting line is taped to the spool housing.
Remove the tape holding the cutting line (15)
to the spool housing (14).
Fitting the plant protector (fig. C)
The plant protector is supplied as a standard accessory with the GL660P & GL670P. For other models, it is available as an optional accessory.
Place the plant protector (17) over the guard as
shown. Make sure that the orientation is correct.
Place the two plastic caps (18) onto the plant
protector, aligning any of the marks (19) on the caps with those on the guard (11).
Secure the caps using the screws (20). Do not
overtighten the screws.
Wait until the cutting line has come to a standstill before adjusting the plant protector.
Connecting the tool to the mains (fig. A)
Connect the female plug of a suitable
extension cable to the power inlet (4).
Loop the cable through the cable restraint as
shown in fig. O.
Insert the mains plug into a mains outlet.
The extension cable must be suitable for outdoor use.
USE
ASSEMBLY
Before assembly, make sure that the tool is switched off and unplugged.
Let the tool work at its own pace. Do not overload.
11
ENGLISH
Setting the tool to trimming or edging mode (fig. D, E & F)
The tool can be used in trimming mode as shown in fig. D or in edging mode to trim overhanging grass along lawn edges and flower beds as shown in fig. E.
Trimming mode (fig. D & F)
For trimming, the trimmer head should be in the position shown in fig. D. If it is not:
Turn the locking ring (7) counterclockwise.
Rotate the trimmer body counterclockwise
until the trimmer head engages in the trimming position.
Tighten the locking ring by turning it clockwise.
Edging mode (fig. E & F)
For edging, the trimmer head should be in the position shown in fig. E. If it is not:
Turn the locking ring (7) counterclockwise.
Rotate the trimmer body clockwise until the
trimmer head engages in the edging position.
Tighten the locking ring by turning it clockwise.
GL670/GL670P - Adjusting the position of the secondary handle (fig. A & G)
The secondary handle can be adjusted to provide optimum balance and comfort.
Let the guard (11) rest on the ground.
While keeping the handle button (6) depressed,
move the handle (5) into the desired position.
Release the handle button.
GL660/GL660P/GL670/GL670P ­Adjusting the height of the tool (fig. A & H)
This tool has a telescopic body, allowing you to set it to a comfortable height.
Let the guard (11) rest on the ground.
Turn the locking ring (7) counterclockwise.
Move the switch handle up or down to the
desired height.
Tighten the locking ring by turning it clockwise.
GL670/GL670P ­Adjusting the trimmer head angle (fig. I)
The adjustable trimmer head angle allows you to set the optimum trimming angle regardless of your length. It also allows you to trim under benches and shrubs.
Let the guard (11) rest on the ground.
Keeping the pedal (10) depressed with your
foot, move the switch handle up or down as required.
Release the pedal.
Switching on and off (fig. A)
To switch the tool on, push the on/off switch (1).
To switch the tool off, release the the on/off
switch.
Never attempt to lock a switch in the on position.
Hints for optimum use
Trimming
Hold the tool as shown in fig. D.
Gently swing the trimmer from side to side as
shown in fig. D.
When cutting long grass, work in stages from
the top. Take small cuts.
Keep the tool away from hard objects and
delicate plants.
If the tool starts running slowly, reduce the load.
Edging
Optimum cutting results are achieved on edges deeper than 50 mm.
Do not use the tool to create edges. To create
edges, use an edging spade.
Guide the tool as shown in fig. E. Keep the
edge guide against the lawn edge.
To make a closer cut, slightly tilt the tool.
General
In order to achieve optimum cutting results,
only cut dry grass.
GL660P/GL670P - Using the plant protector (fig. J)
The plant protector will help you to protect plants while trimming along lawn edges.
12
ENGLISH
In trimming mode, set the plant protector to
position A.
In edging mode, set the plant protector to
position B or C.
When there are no plants near the cutting
area, set the plant protector to position D.
MAINTENANCE
Your Black & Decker tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.
Before performing any maintenance, switch off and unplug the tool.
Regularly clean the ventilation slots in your tool
using a soft brush or dry cloth.
Regularly clean the cutting line and spool
using a soft brush or dry cloth.
Regularly use a blunt scraper to remove grass
and dirt from the underneath of the guard.
Fitting a new spool of cutting line (fig. K & L)
Replacement spools of cutting line are available from your Black & Decker dealer (cat. no. A6441). Complete cassettes containing a spool of cutting line are also available (cat. no. A6442).
Unplug the tool.
Keep the tabs (21) depressed and remove the
spool cover (22) from the housing (23) (fig. K).
Remove the empty spool (24) from the
spool cover.
Remove any dirt and grass from the spool
cover and housing.
Take the new spool and push it onto the boss
in the spool cover. Rotate the spool slightly until it is seated.
Unclip the end of one of the cutting lines and
guide the line into one of the eyelets (25) (fig. L). The line should protrude approx. 9 cm from the spool cover.
Unclip the end of the other cutting line and
guide the line into the other eyelet. The line should protrude approx. 9 cm from the spool cover.
Align the tabs (21) on the spool cover with the
holes (26) in the housing (fig. K).
Push the cover onto the housing until it snaps
securely into place.
If the cutting lines protrude beyond the trimming blade (12), cut them off so that they just reach the blade.
Winding new line onto an empty spool (fig. M, N & P)
You may wind new cutting line onto an empty spool. Replacement packs of cutting line are available from your Black & Decker dealer (cat. no. A6440).
Remove the empty spool from the tool as
described above.
Remove any remaining cutting line from
the spool.
First wind new line onto the uppermost part of
the spool:
- Feed 2 cm of cutting line into one of the slots in the upper section of the spool as shown.
- Wind the cutting line onto the spool in the direction of the arrow. Make sure to wind the line on neatly and in layers. Do not criss-cross.
- When the wound cutting line reaches the recesses (28), cut the line.
- Temporarily park the line in the slots (27) on one side of the spool as shown.
Repeat the above procedure for the second
cutting line on the lower section of the spool. Park the line in the unused slots (27).
Proceed as described above to fit the spool on
the tool. Do not forget to release the cutting line from the parking slots (27).
Only use the appropriate type of Black & Decker cutting line. Ensure that cutting line is present in both sections of the spool (fig. P).
TROUBLESHOOTING
If your tool seems not to operate properly, follow the instructions below. If this does not solve the problem, please contact your local Black & Decker repair agent.
13
ENGLISH
Before proceeding, unplug the tool.
Tool runs slowly
Check that the spool housing can rotate freely.
Carefully clean it if necessary.
Check that the cutting line does not protrude
more than 9 cm from the spool housing. If it does, cut it off so that it just reaches the line trimming blade.
Automatic line feed does not work
Keep the tabs depressed and remove the
spool cover from the housing.
Pull the cutting line until it protrudes 9 cm from
the housing. If insufficient cutting line is left on the spool, install a new spool of cutting line as instructed above.
Align the tabs on the spool cover with the
holes in the housing.
Push the cover onto the housing until it snaps
securely into place.
If the cutting line protrudes beyond the
trimming blade, cut it off so that it just reaches the blade.
If the automatic line feed still does not work or the spool is jammed, try the following suggestions:
Carefully clean the spool cover and housing.
Remove the spool and check if the lever can
move freely.
Remove the spool and unwind the cutting line,
then wind it on neatly again as described above. Replace the spool as instructed.
GUARANTEE The Black & Decker lawn and garden guarantee provides: 36 months parts and 12 months labour cover in the UK, 24 months parts and labour cover in South Africa, Australia and New Zealand. Proof of purchase will be required.
Should your Black & Decker product become defective within the guarantee period due to faulty materials or workmanship, we guarantee to either replace all defective parts or -at our discretion- to replace the unit free of charge, provided that:
The product is returned to us or one of our
authorised repair agents with proof of purchase.
The product has been used within the
parameters of its consumer classification.
The product has not been used for hire purposes.
Repairs have not been attempted by anyone
other than our authorised repair agents.
The failure represents normal wear and tear.
This guarantee is offered as an extra benefit and does not affect your statutory rights.
The guarantee policy
The following failures are not covered by the above guarantee:
Replacing worn or damaged blades, nylon
lines, chains and power cables. These items are regarded as replacement items which wear during normal usage.
Failures as a result of sudden impact or
obvious abuse.
Failures due to usage not in accordance with
instructions and recommendations contained in this manual.
PROTECTING THE ENVIRONMENT
Should you find one day that your tool needs replacement, or if it is of no further use to you, think of the protection of the environment. Black & Decker repair agents will accept old Black & Decker tools and ensure that they are disposed of in an environmentally safe way.
14
The use of other than genuine Black & Decker accessories and parts may cause decreased performance or damage to the product and will render the guarantee void.
AFTER SALES SERVICE
Full details on our after-sales service are available on the Internet at www.2helpU.com. Alternatively, contact our Service and Information Centre at the address towards the back of this manual.
It is our aim that all Black & Decker customers should be totally satisfied with their Black & Decker product and our after sales service. If any help or advice is needed, please contact your local Black & Decker repair agent.
If your product needs repair, please take or send it to an authorised repair agent, providing proof of purchase if claiming a guarantee repair. Black & Decker offers a nationwide network of authorised repair agents.
Full details on our after sales service can be obtained from any of our authorised repair agents.
OTHER OUTDOOR TOOLS
Black & Decker has a full range of outdoor power tools that make life in the garden easy. If you would like further information on the following products, please contact our Service and Information Centre (see the address page towards the end of this manual) or your local Black & Decker retailer.
String trimmers Chainsaws Cordless shear Hedgetrimmers Lawnmowers Lawnrakers Leafbusters Shredders
ENGLISH
Not all products are available in all countries.
15
Loading...
+ 33 hidden pages