Black & Decker BDWF7710 User Manual

PLEASE READ AND SAVE THIS USE AND CARE BOOK. POR FAVOR LEA ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. VEUILLEZ LIRE ET CONSERVER CE GUIDE D’ENTRETIEN ET D’UTILISATION.

Accessories/Parts (USA/Canada) 1-800-738-0245 Accesorios/Partes

(EE.UU/Canadá)

Accessoires/Pièces (É.-U./Canada)

USA/Canada 1-800-231-9786 Mexico 01-800-714-2503

www.blackanddecker.com

Model/Modelo/Modèle

BDWF7710

Digital Twin Window Fan with Rainsafe

™

Sensor Ventilador doble dígital con sensor

Rainsafe

™

para ventana

Ventilateur double à affichage numérique de fenêtre avec capteur Rainsafe

BDWF7710Pub1000001430 10/11/04 4:51 PM Page 1

When using electrical appliances, basic safety precautions should always be followed, including the following:

❑

READ AND SAVE THESE INSTRUCTIONS.

❑

Use fan only for intended use, as described in instruction manual.

❑

To protect against electrical shock, do not immerse unit, plug, or cord in water or spray with liquids.

❑

Close supervision is necessary when any appliance is used by or near children.

❑

Unplug from outlet when not in use, when moving fan from one location to another, before putting on or taking off parts and before cleaning.

❑

Never insert fingers, pencils or any other objects through the grille when fan is running.

❑

Disconnect fan before cleaning.

❑

Make sure fan is on a stable surface when operating to avoid chance of overturning.

❑

Do not place fan or any parts near an open flame, cooking or other heating appliances.

❑

Do not operate any appliance with a damaged cord or plug, after the appliance malfunctions or has been dropped or damaged in any manner. Return the fan to the nearest authorized service facility for examination, or electrical or mechanical adjustment. Or, call the appropriate toll-free number listed on the cover of this manual.

❑

Do not use attachments not recommended by the manufacturer.

❑

Do not let cord hang over table or counter or touch hot surfaces.

❑

To disconnect, grip plug and pull from wall outlet. Never yank on cord.

❑

Always use on a dry, level surface.

WARNING: To reduce the risk of fire or electrical shock, do not use this fan with any solid-state speed control device.

SAVE THESE INSTRUCTIONS.

IMPORTANT SAFETY

INSTRUCTIONS

POLARIZED PLUG (120V Models Only)

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way.

Note: If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

BDWF7710Pub1000001430 10/11/04 4:51 PM Page 2





















†1.Panel insert

(2 panel inserts per set Part #103409900592)

2. Groove

3. Digital control panel

4. Carry handle

5. Release clamp

6. Expandable panel

7. Twin motors

8. 7" (18cm) reversible blades

9. Remote control storage

†10. Remote control

(Part #103530000021)

†11. Optional feet

(2 optional feet per set, right Part #103409900583, left Part # 103409900584)

12. 10' cord (25 cm)(not shown)

13. Screws (not shown)

† Consumer replaceable

Product may vary slightly from what is illustrated.















1. 3-Speed/On/Off button

2. Reverse buttons

3. Digital temperature display

4. Rainsafe™ button

5. Remote control sensor

6. Adjustable thermostat buttons

7. Temperature control button

How to Use

This appliance is for household use. IMPORTANT: During the first few minutes of initial use, a slight odor may be noticeable.

This is normal and will quickly disappear.

INSTALLATION INSTRUCTIONS

1. Unpack twin window fan carefully.

2. This unit is designed for use in double-hung, casement and vertical slider-type windows with minimum openings of 23.5" (59.5 cm) wide and 11.2" (28.5 cm) high.

3. This fan is designed to be used (and recommended for use) with a screen in the window.

4. With the sliding portion of the window fully open, take an accurate inside measurement (left to right for double-hung type windows and top to bottom for vertical slider-type windows) of the window opening where the unit is to be placed.

For double-hung type windows

1. With the window fully open, set the fan in the window with front of fan facing the INSIDE.

2. Hold fan with one hand while attaching/adjusting panels with the other. Attach one of the panel inserts by sliding it down the groove located at the top left of fan. Before closing window, pull open clamps located at top and bottom on right side on fan, and adjust expandable panel, if necessary.

3. Close the window on top of the fan with the bottom edge of the window behind the lip of fan housing.

4. If the fan still does not fit properly in the window, readjust the expandable panel on right side of fan to fill in remaining space between panel and window frame until a secure fit is achieved.

For vertical slider-type windows

1. Position the fan in the window with the power switch facing the center of the opening.

2. To adjust height, remove fan from window. If additional height required is 4" (10 cm) or less, extend the expandable panel until it matches the height of the window. (For example, if window height is 28" (71 cm), adjust panel so that the height of the fan is also 28" (71 cm)). If fan height required is more than 28" (71 cm), attach one or both of the insert panels, as described in #2 of FOR DOUBLE-HUNG TYPE WINDOWS section above.

3. With the window fully open, position the fan in the window with the expandable panel at the top and with power switch facing the center of the opening.

4. Fan must fit securely against the inside edge of the window opening.

5. Slide the sliding window to meet the edge of the fan. The side edge of the window must fit securely behind the lip of fan housing.

6. Adjust the expandable panel to fill in remaining space between fan and window frame.

Expandable panel locks into position by closing the clamps once fit is established. OPERATING INSTRUCTIONS

1. Plug into 120V AC electric outlet.

2. On/Off/SPEED— Press speed button to turn the fan on. Fan default direction when the unit is turned on is intake. Fan begins blowing at LOW speed, the corresponding LED speed indicator illuminates. To turn the fan off press the speed button through the cycle (LOW, MED, HI) until all speed lights are off.

3. Intake/Exhaust/Exchange — Both fans are automatically reversible and operate independently in either an intake or exhaust mode. The IN/OUT directional LED illuminates green for intake and red for exhaust. To pull in fresh air from the outside – push reverse button to IN (green). To remove stale or smoky air from the room - push reverse button to OUT (red). For air exchange –set one button to IN (green) and one button to OUT (red).

BDWF7710Pub1000001430 10/11/04 4:51 PM Page 4

4. Temperature programming — a) Press and hold the temperature control button for 3 seconds. Display blinks. "SET"

indicator in digital display is highlighted

b)Press the "+" or "-" adjustable thermostat buttons to select indoor temperature to turn

fan on. (Temp range: 65-90°F (18,3 °C a 32,2 °C ) )

c) Press the temperature control button to activate the

temperature mode. Display stops blinking.

ROOM temperature indicator is highlighted, displaying indoor temperature. SET temperature indicator is highlighted, displaying indoor temperature set for fan to start. LED temperature indicator blinks red when actual indoor temperature is below set temperature.

Note: Fan does not activate until set temperature is reached. Press the temperature control button again to de-activate the temperature mode. LED

temperature indicator will not be illuminated.

5. Fans — Select speed setting for both fans. Press speed button: Once for LOW Twice for MED Three times for HI Fourth press of speed button turns the fan off. Next press of button repeats the cycle. Press the fan direction intake/exhaust button to exhaust. The speed when the button is pressed remains the same.

Note: Fans shut off automatically once the set temperature is reached. If the unit does not start, make sure that the "set temperature" is below the current room temperature. If the fans are stopped and you want to turn them back on, lower the temperature setting until you have reached the desired temperature. Press the temperature control button to deactivate the temperature mode. To reactivate at the current temperature settings press the temperature control button.

6. Rainsafe™ feature — only operates in the intake mode. When raindrops hit the Rainsafe™ sensor on the back of the fan (A), unit turns off to prevent water from entering the fan and being blown inside the room. Press the Rainsafe™ button to activate. LED (red) illuminates continuously indicating activation. Detection by Rainsafe™ feature automatically shuts off the fan. LED Rainsafe™ indicator blinks to show that the Rainsafe™ sensor has turned off the fan. Fan automatically restarts after the water evaporates. Note: If the fan has shutoff due to the Rainsafe™ feature being activated, you can restart the fan by pressing the Rainsafe™ button, therefore bypassing the Rainsafe™ function. Press Rainsafe™ button a second time to deactivate the Rainsafe™ feature. LED Rainsafe™ indicator will not be illuminated.

To Use with the Remote Control

The remote control (B) operates on 2 AAA batteries. Batteries are not included. Slide the cover off the battery compartment on the back of the remote and install the batteries in the orientation shown inside.

• The remote control (B) lets you operate the fan from a distance.

• When pushing buttons, be sure to direct the remote toward the remote control sensor on the digital control panel. Make sure there is nothing obstructing the path.

• After use, place the remote control into the remote control storage area at the bottom, front of fan.

For Use As A Floor Or Table Fan

Optional feet are included to enable the window fan to stand on its own. To attach the optional feet, line up tab on back of foot with hole on back of fan base and snap front of foot into place. Repeat procedure with other foot. Secure feet with screws (included).

Care and Cleaning

This product contains no user serviceable parts. Refer service to qualified service personnel. This fan is permanently lubricated and will not require additional lubrication for the life of the fan.

Cleaning

1. Turn off fans and unplug.

2. Remove fan from window and detach any panel inserts from fan assembly.

3. Wipe off excess dust with a lint-free cloth. To ensure adequate air circulation, keep vents dust free. A vacuum cleaner hose may be used to clean the vents.

4. DO NOT immerse the fan in water or any other liquid.

5. Be sure all parts of fan are completely dry before operating.

Storing

• Make sure to clean the fan before storing.

• Retain the original packaging for storing your fan.

• Always store fan in a dry place.

• Never store it while it is still plugged in.

• Never wrap the cord tightly around the fan, and do not put any stress on the cord where it enters the fan, as it could cause the cord to fray and break.

BDWF7710Pub1000001430 10/11/04 4:51 PM Page 6

+ 9 hidden pages