B&K Precision Corp.
22820 Savi Ranch Pkwy
Yorba Linda, CA 92887
TEL: 714-921-9095
FAX: 714-921-6422
PN: 481-401-9-001
Printed in USA
2002 B&K Precision Corp.
Instruction Manual
www.bkprecision.com
r
Model 240A Remote Network Cable Analyze
Limited One-Year Warranty
B&K Precision Corp. warrants to the original purchaser that its product and the
component parts thereof, will be free from defects in workmanship and materials for a
period of one year from the data of purchase.
B&K Precision Corp. will, without charge, repair or replace, at its’ option, defective
product or component parts. Returned product must be accompanied by proof of the
purchase date in the form a sales receipt.
To obtain warranty coverage in the U.S.A., this product must be registered by
completing and mailing the enclosed warranty card to B&K Precision Corp., 22820
Savi Ranch Parkway – Yorba Linda, CA 92887 within fifteen (15) days from proof of
purchase.
Exclusions: This warranty does not apply in the event of misuse or abuse of
the product or as a result of unauthorized alternations or repairs. It is void if
the serial number is alternated, defaced or removed.
B&K Precision Corp. shall not be liable for any consequential damages, including
without limitation damages resulting from loss of use. Some states do not allow
limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
This warranty gives you specific rights and you may have other rights, which vary
from state-to-state.
Model Number: ______________ Date Purchased: __________
Service Information
Warranty Service: Please return the product in the original packaging with proof of
purchase to the below address. Clearly state in writing the performance problem and
return any leads, connectors and accessories that you are using with the device.
Non-Warranty Service: Return the product in the original packaging to the below
address. Clearly state in writing the performance problem and return any leads,
connectors and accessories that you are using with the device. Customers not on
open account must include payment in the form of a money order or credit card. For
the most current repair charges contact the factory before shipping the product.
Return all merchandise to B&K Precision Corp. with pre-paid shipping. The flat-rate
repair charge includes return shipping to locations in North America. For overnight
shipments and non-North America shipping fees contact B&K Precision Corp..
B&K Precision Corp.
22820 Savi Ranch Parkway
Yorba Linda, CA 92887-4604
Phone: 714- 921-9095
Facsimile: 714-921-6422
Email: service@bkprecision.com
Include with the instrument your complete return shipping address, contact name, phone
number and description of problem.
Introduction
Congratulations on your purchase of the Model 240A Remote Network Cable
Analyzer! The 240A is a small hand-held cable tester, which enables network
professionals to quickly and easily verify the integrity of Ethernet twisted pair
cables. In on step, the 240A will test twisted pair cables for open pairs, shorted pairs,
reversed pairs, crossed pairs and split pairs. Just push the TEST button, and the 240A
will automatically scan for any existing faults in your cable. The design patented
remote terminator is provided for one-person testing of installed cables. The 240A
can generate both signal and dual tones when used as a Tone Generator.
Package Contents
- One Model 240A Main Unit
- One Remote Terminator
- Users Manual
- Patch Cable
Product Profile
1. RJ45 jack
2. Pair 1 indicator
3. Pair 2 indicator
4. Pair 3 indicator
5. Pair 4 indicator
6. Shield indicator
7. Short fault indicator
8. Reversed fault indicator
9. Miss wire fault indicator
10. Split pairs indicator
11. Low battery indicator
Features
Features
- Tests for wiring faults of open, short, reversed, crossed and split pairs
- Split pair fault detection at a minimum 1.97’ (0.6cm) cable length
- Verification of shield integrity
- Specially designed remote unit that enables one person to test installed
- Easy to read fault display and high speed testing
- Debug mode for detailed fault identification results
- Auto power off to decrease power consumption
- Low battery indicator
- Tone Generator (single and dual tone)
Specifications
- Connectors
- Pairs Tested
- LED Display
- Cable Test Length Limit
- Power
- Dimensions HxWxD (with belt clip & rubber boot)
- Weight (with belt clip & rubber boot)
2
cables
Model 240A Master Unit – RJ45 jack
Remote Unit – RJ45 jack
1/2, 3/6, 4/5, 7/8 and shield
5 horizontally aligned green LEDs for pairs and shield display
5 vertically aligned red LEDs for fault display
1 stand alone LED for Tone Generator active display
Minimum: 1.97 ft. (0.6m) Maximum: Over 656 feet (200m)
240A Master Unit – 9V Alkaline Battery (not included)
Remote Unit – no battery required
5 x 3 x 1.6” (128 x 77 x 40mm)
6.1oz (172g)
Test Operations
1. Plug one end of the subject cable into the RJ45 jack on the master unit and
the other end into the RJ45 jack on the remote terminator.
2. Push and release the test button and check the results:
a. First check the 5 horizontally aligned green LED indicators (1-2,
3-6, 4-5, 7-8, shield) for integrity status:
Solid light = pair is OK
Flashing light = pair is faulty
No light = open pair
b. Simultaneously, check the 4 vertically aligned LED indicators
(short, reversed, miswire, split pairs) for the wiring faults.
c. For more detailed information about what faults are occurring in
which pairs, hold the TEST button for 2 seconds to activate
“Debug Mode”. The tester will test each pair on by one, pausing
briefly on each pair, and display the corresponding fault status.
3. After the test is done the device will automatically turns itself off.
Tone Generator Operations
1. Connect the subject cable to the RJ45 jack on the top of the master unit of
the tester. To send a tone into a patch panel, connect one end of a patch cord
to the RJ45 jack on the tester and the other end to a jack on the patch panel.
2. Generating a tone:
a. Single tone – press TONE and TEST button simultaneously and
then release both buttons before 2 seconds elapse.
b. Dual tone - press TONE and TEST button simultaneously holding
them down for more than 2 seconds.
3. Use Model 261 cable tracer or any cable tracing product in the market to
trace the subject cable. The signal reception will be strongest near the
subject cable.
4. Press either TEST or TONE to stop the generator.
Battery Replacement
When the LOW BATTERY light illuminates, the battery does not have sufficient
power to support an accurate test. At this time, you must replace it with a new
battery.
Warning
1. Do not connect the 240A to a live circuit as this may damage the tester.
3
2. Testing in a high frequency activated area may cause the tester to give
inaccurate readings.
3. Do not drop or get the tester wet as it may cause internal damage.
4. Do not place the tester in areas of high humidity or direct sunlight.
5. Do not open the tester or attempt to repair in case of malfunction. Please
send it back to your distributor for repair or replacement.
Table of Contents
Introduction…………………………………………. 2
Package Contents…………………………...………. 2
Product Profile………………………………………. 2
Features……………………………………..………. 3
Specifications………………………………………. 3
Test Operations…………………………..…………. 3
Tone Generator Operations…………..………….…. 4
Battery Replacement…………..………….………… 4
4
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
B&K Precision:
240A
Loading...