Page 1
®
USER GUIDE
PROFESSIONAL PET
DEEPCLEAN PROHEAT 2X
17N4 SERIES
COSTCO ITEM# 899110
Page 2
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR DEEP CLEANER.
When using an electrical appliance, basic precautions should be observed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY:
» Connect to a properly grounded
outlet only. See grounding
instructions. Do not modify the
3-prong grounded plug.
» Do not leave appliance when it is
plugged in. Unplug from outlet when
not in use and before servicing.
» Use indoors only.
» Do not allow to be used as a toy.
Close attention is necessary when
used by or near children.
» Do not use for any purpose other
than described in this User ’s
Guide. Use only manufacturer’s
recommended attachments.
» Do not use with damaged cord
or plug. If appliance is not
working as it should, or has been
dropped, damaged, left outdoors,
or dropped into water, have it
repaired at an authorized
service center.
» Always install float before any wet
pick-up operation.
» Do not pull or carry by cord, use
cord as a handle, close a door on
cord, or pull cord around sharp
edges or corners. Do not run
appliance over cord. Keep cord
away from heated surfaces.
» Do not unplug by pulling on
cord. To unplug, grasp the plug,
not the cord.
» Do not handle plug or appliance
with wet hands.
» Do not put any object into open-
ings. Do not use with any opening
blocked; keep openings free of
dust, lint, hair, and anything that
may reduce air flow.
» Keep hair, loose clothing, fingers,
and all parts of body away from
openings and moving parts.
» Turn off all controls before plug
ging or unplugging appliance.
» Use extra care when cleaning
on stairs.
» Do not use to pick up flammable
or combustible materials (lighter
fluid, gasoline, kerosene, etc.)
or use in areas where they may
be present.
» Do not use appliance in an
enclosed space filled with vapors
given off by oil base paint, paint
thinner, some moth proofing
substances, flammable dust,
or other explosive or toxic vapors.
» Do not use to pick up toxic
material (chlorine bleach,
ammonia, drain cleaner, etc.).
» Do not pick up anything that
is burning or smoking, such as
cigarettes, matches, or hot ashes.
» Use only BISSELL cleaning
products intended for use
with this appliance to prevent
internal component damage.
See the Cleaning Fluid section
of this guide.
» Unplug before connecting
TurboBrush Tool.
» Do not immerse. Use only on
surfaces moistened by the
cleaning process.
» Keep appliance on a level surface.
» Do not carry the appliance while
in use.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE
This model is for household use only. Commercial use of this unit voids the manufacturer’s warranty.
WARNING
Improper connection of the equipment-grounding conductor can
result in a risk of electrical shock. Check with a qualified electrician
or service person if you aren’t sure if the outlet is properly grounded.
DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper
outlet installed by a qualified electrician. This appliance is designed
for use on a nominal 120-volt circuit, and has a grounding attachment
plug that looks like the plug in the illustration. Make certain that the
appliance is connected to an outlet having the same configuration as
the plug. No plug adapter should be used with this appliance.
www.BISSELL.com
2
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded wiring system. If it
should malfunction or break down, grounding provides a safe path
of least resistance for electrical current, reducing the risk of electrical
shock. The cord for this
appliance has an equipment-grounding
conductor and a grounding plug. It must
only be plugged into an outlet that is
properly installed and grounded in
accordance with all local codes and ordinances.
Grounded
Outlets
Grounding Pin
Page 3
Th for buying a BISSELL dp cleer
We’re glad you purchased a BISSELL
deep cleaner. Everything we know
about floor care went into the design
and construction of this complete,
high-tech home cleaning system.
Your BISSELL deep cleaner is well
made, and we back it with a limited
three-year warranty. We also stand
behind it with a knowledgeable,
dedicated Consumer Care
department, so, should you ever
have a problem, you’ll receive fast,
considerate assistance.
My great-grandfather invented
the floor sweeper in 1876. Today,
BISSELL is a global leader in the
design, manufacture, and service
of high quality homecare products
like your BISSELL deep cleaner.
Thanks again, from all of us
at BISSELL.
Safety Instructions...........2
Product View ................4
Assembly ...................5
Operations ...............5-12
Maintenance & Care ......13-15
Troubleshooting ............16
Replacement Parts ......... 17
Accessories ................18
Warranty ...................19
Consumer Care.............19
Product Registration ....... 20
Mark J. Bissell
Chairman & CEO
www.BISSELL.com
3
Page 4
Product View
1
2
3
5
6
7
8
9
10
4
11
12
13
14
www.BISSELL.com
4
1 Spray Trigger
2 Extra Long Power Cord
3 Upper Handle
4 Flex Hose
5 Power Switch
6 Easy Carry Handle
7 Tank Carry Handle
8 Large Capacity 2-in-1 Water Tank
9 Easy To Remove Nozzle
10 EdgeSweep® Brushes
11 Lower Base
12 Upper Hose Rack
13 Lower Hose Rack
14 Handle Recline Pedal
Page 5
Asmbly
Your deep cleaner comes in four
easy-to-assemble components:
Upper Handle with Screws
(screws taped to handle)
Lower Base
Upper Hose Rack
Upper Tool Holder
The only thing you will need to assemble
your cleaner is a Phillips head screwdriver.
1. Slide upper handle onto lower base.
2. Screw 2 screws into the marked holes.
3. Attach the upper tool holder to the upper
handle by snapping the bottom half in first,
then snapping in the top half.
4. Place upper hose rack onto back of
upper handle, and secure with screw.
5. Snap tools onto the Upper Tool Holder.
6. Wrap power cord and flex hose. Snap hose
wand into hose clip on upper hose wrap.
NOTE: Take care to wrap the hose in the
right direction in order to make use of the
hose clip. Make sure the hose is wrapped
beginning from the back of the machine
and wrapping toward the front.
Your deep cleaner assembly is now complete!
WARNING
Do not plug in your deep cleaner until
you are familiar with all instructions and
operating procedures.
1. 2.
3.
4a.
5.
4b.
6.
Operatis
Cleaning fluid
Keep plenty of genuine BISSELL 2X formula on
hand so you can clean and protect whenever it
fits your schedule. Always use genuine BISSELL
deep cleaning formulas. Non-BISSELL
cleaning solutions may harm the machine and
will void the warranty.
Professional
Deep Cleaning
Best for
2X Concentrated X X X X X
Scotchgard™ Protection
*ONLY BISSELL Protects from future stains with Scotchgard™ Protector
Out Cleans
all other
formulas
®
Pet Stain & Odor
Removes tough pet
stains and contains
patented odor
removal technology
X X X
Deep Clean
& Protect
Deep cleans carpets
and protects from
future stains with
Scotchgard™ Protector
Allergen Cleansing DeepClean + Refresh Stain Pretreat
Helps remove pet &
pollen allergens
Powerful
cleaning with a
refreshing scent
WARNING
To reduce the risk of fire and electric shock
due to internal component damage, use
only BISSELL cleaning fluids intended for use
with the deep cleaner.
Pretreat to
penetrate
and loosen
tough stains
www.BISSELL.com
5
Page 6
Operatis
1
2
3
4
5
6
7
8
9
Before you clean
1. Move furniture to another area if cleaning
an entire room (optional).
2. Pick up all loose dirt, debris, and pet hair
before deep cleaning. It is recommended that
you vacuum the area prior to deep cleaning.
3. Plan your cleaning route to leave an exit
path. It is best to begin cleaning in the corner
farthest from your exit.
4. Pretreating (optional) is recommended to
improve cleaning effectiveness for heavily soiled
carpet in high traffic areas such as entryways
and hallways.
BISSELL Stain Pretreat
a. Spray the BISSELL Stain Pretreat
formula onto heavy traffic areas, soiled
areas, or stains.
b . Allow to penetrate for at least 3 minutes.
c. Clean as normal following the instructions
on the next page.
Machine Prep
Fill the 2-in-1 Water Tank
1. Remove the tank from the base of the machine
by lifting up the tank carry handle. Carry like a
bucket to the sink.
2. Unlatch the top of the tank from the bottom
by lifting up on the tank latches on either
side of the tank.
3. Using the measuring cup provided, pour
5 oz of BISSELL 2X formula into the heavy
duty bladder. Fill the rest of the heavy duty
bladder with hot (140°F/60°C MAX) tap water.
DO NOT BOIL OR MICROWAVE WATER.
NOTE: Always use genuine BISSELL 2X
formulas to maximize cleaning and for the
safety of your machine.
4. Place the top of the tank back on the
bottom and secure the latches on both sides.
NOTE: Remember to secure the tank latches
on either side of the tank and test to make sure
they are secure before picking up the tank.
ATTENTION
Some Berber carpets have a tendency to fuzz
with wear. Repeated strokes in the same area
with an ordinary vacuum or deep cleaner
may aggravate this condition. Please see Stain
Removal instructions on page 12.
1. 2.
3. 4.
WARNING
To reduce the risk of fire and electric shock
due to internal component damage, use
only BISSELL cleaning fluids intended for use
with the deep cleaner.
www.BISSELL.com
6
Page 7
Operatis
Carpet cleaning
1. Plug into a proper outlet and push the on/off
button located on the front of
the handle.
2. Recline the handle by pressing on the lever
at the back of the machine behind the 2-in-1
water tank.
3. Cleaning Strokes. While pressing the trigger,
make one slow forward wet pass and another
one back. Caution: Do not overwet. Take care
not to run over loose objects or edges of area
rugs. Stalling brush may result in premature
belt failure.
NOTE: Your machine is equipped with a circuit
breaker that will automatically shut off the
brush if a large or loose object is caught in the
brush roll. If that happens, be sure to unplug
your machine, remove the foreign object, and
then plug the machine back in to reset the
circuit breaker.
4. Release the trigger and make one slow
forward and backward pass over the same area
to remove any residual dirty water and aid in
drying. Repeat cleaning passes until solution
being pulled up appears clean. Continue
passes without pressing the trigger until you
can’t see any more water being pulled up.
1. 2.
www.BISSELL.com
7
Page 8
Operatis
Adsdfdd ghg bvh
cvbbj jkn hnbj jkvh
gcghhjj jhffhl kllgh
Cleaning with attachments
Your deep cleaner comes equipped with
a hose and at least one attachment for
cleaning stairs, upholstery, and more.
1. Important! If using to clean upholstery,
check upholstery tags before cleaning.
1. Check manufacturer’s tag before cleaning.
“W” or “WS” on the tag means you can use your
deep cleaner. If the tag is coded with an “X” or
an “S” (with a diagonal stripe through it), or says
“Dry Clean Only”, do not proceed with any deep
cleaning machine. Do not use on velvet or silk.
If manufacturer’s tag is missing or not coded,
check with your furniture dealer.
a. Check for colorfastness in an
inconspicuous place.
b . If possible, check upholstery stuffing.
Colored stuffing may bleed through
fabric when wet.
c. Plan activities to allow upholstery
time to dry.
d. Pick up any loose dirt, debris and
pet hair before deep cleaning.
2. Follow the instructions on page 6 for
filling the 2-in-1 water tank.
3. The machine is designed with an automatic
diverter. Simply lock the unit upright in order to
clean with the hose.
4. Attach the cleaning tool to the end of the hose.
5. Plug in and turn on the power switch.
NOTE: Instructions for Stain Trapper Tool and
3-N-1 Tool are on pages 9 & 10.
6. Clean by pressing the trigger to spray
solution onto the area to be cleaned. Slowly
move the tool back and forth over the soiled
surface. Release the trigger to suction soiled
water. Continue to clean in the area, working
in small sections, until no more dirt can be
removed. Rinse (optional) and suction as
needed. Caution: Do not overwet.
7. Remove and rinse tools in clean, running
water. Dry and replace on the end of the hose.
8. It is recommended that you suction clean
water from a bowl to rinse out the hose.
9. Before replacing lift end of hose and stretch
out to ensure all water is cleared from hose.
10. Wrap flex hose around the hose rack.
11. Empty 2-in-1 water tank and rinse out,
following the instructions on page 11.
WARNING
To reduce the risk of injury, be extra careful when cleaning
stairs. Make sure machine is secure and level.
Manufacturer’s tag
4.
9.
www.BISSELL.com
8
Page 9
Operatis
Cleaning with tools
Stain Trapper Tool
The Stain Trapper Tool is great for keeping
messes out of the machine’s hose system.
1. Attach the Stain Trapper tool to the end
of the hose.
2. Gently scrape up any semi-solids with a spoon
or spatula. Do not use a knife or other utensil
with sharp edges because it could damage the
carpet or upholstery.
3. Press the trigger on the hose to spray solution
onto the mess. Use the brushes to gently
scrub the mess and then suction the mess
away. Be careful not to move the tool back
and forth too quickly or soiled water will flow
back into the hose.
NOTE: Do not fill the Stain Trapper tank
above the FULL line.
4. To empty the tool container, rotate to the
unlock symbol.
NOTE: Be careful to keep the top of the tool
facing upward or soiled water will spill out of
the tank.
5. Empty the dirty water into a sink and rinse
with clean water. Replace the container by lining
up and rotating to the lock symbol.
6. The front faceplate of the tool can also be
removed and rinsed for easy cleaning. Simply
pull down on the face plate to remove it.
1.
4.
6.
www.BISSELL.com
9
Page 10
Operatis
3-N-1 Stair Tool
1. Attach the tool to the end of the hose.
2. Twist the tool head to the desired setting:
a. The flat edge can be used to
clean flat areas
b. The pointed edge can be used to
clean crevices
c. The indented edge can be used to
clean curved areas
3. Ensure the tool spray tip is pointing
downward. Press the trigger and slowly move
the tool back and forth over the soiled area.
4. Release the trigger to suction up water
and dirt.
5. To clean the tool, simply remove the tool from
the end of the hose and rinse with water. The
front faceplate of the tool can also be removed
and rinsed for easy cleaning.
1.
2a.
2c.
2b.
5.
www.BISSELL.com
10
Page 11
Operatis
Clean-up
1. Remove the tank from the base of the
machine by lifting up on the tank carry handle.
Carry like a bucket to a utility sink or outside
where you will dispose of the dirty water.
2. Unlatch the top of the tank from the
bottom by lifting up on the tank latches on
either side of the tank.
3. Remove the top of the tank by lifting up
on the handle.
4. Empty the Pet Hair Basket by sliding it
toward the front of the tank and lifting up.
Replace the Pet Hair Basket before storing/
continuing to clean.
5. Lift the bottom portion of the tank; pour out
dirty water in the sink through the rectangular
shaped opening in the corner of the tank.
NOTE: You may notice hair & debris deposits
on the carpet or in the tank that were loosened
by the cleaning action. This debris should be
picked up and thrown away. Check the red lint
filter near the duct on the back of the machine
base for debris and remove before continuing.
6. Fill the heavy duty bladder with clean
hot (140°F/60°C MAX) tap water, following
instructions on page 6.
NOTE: Remember to secure the tank latches
and test to make sure it is secure before
picking up the tank.
7. Water rinse (recommended). Rinsing
is an optional step that can be done during the
cleaning process or after the carpeted area has
been completed. Empty the heavy-duty bladder
if necessary, and refill with hot tap water only.
Replace the tank on the machine. Take care to
do a forward (wet) stroke by depressing the
trigger, and a backward (wet) stroke, followed by
a forward and backward (dry) stroke, releasing
the trigger. Continue this until the water you see
coming up the nozzle is clear. (See page 13 for
more machine care tips.)
1.
3.
5.
2.
4.
Filter
www.BISSELL.com
11
Page 12
Operatis
Stain removal
Do Not Delay! Attending to an accident soon
after it occurs ensures the most optimal clean.
Leaving it for an extended period of time may
cause it to set and become permanent.
1. Blot up liquids with an absorbent cloth or
paper towels. White materials are recommended
because certain dyes may bleed and make the
stain worse.
2. Gently scrape up any semi-solids with a spoon
or spatula. Do not use a knife or other utensil
with sharp edges because it could damage the
carpet or upholstery.
3. If the area has already dried, separate and
remove from the carpet whatever semi-solids
and residue that can be accessed before deep
cleaning.
4. Be sure to test any spot removal formulas in
an inconspicuous area first. This is important as
some dyes and materials could be damaged or
discolored by cleaning solvents. If such a change
should occur, try a different solution or call a
professional.
5. If cleaning on Berber carpeting, gently run
your machine over a hidden area. If no fuzzing
occurs, continue cleaning in soiled area.
6. Using the BISSELL Stain Pretreat, spray evenly
over soiled area. Do not overwet. Wait 3-5
minutes. Gently work the solution by blotting
area with a clean, damp, color safe cloth.
7. Clean large areas with the machine or use
the hose to clean spots, stains and hard-toreach areas.
Machine storage
Once your cleaning is complete, make sure the
2-in-1 water tank is emptied, rinsed out, and
dried before the next use.
NOTE: Store cleaner in a protected, dry area.
Since this product uses water, it must not be
stored where there is a danger of freezing.
Freezing will damage internal components
and void the warranty.
www.BISSELL.com
12
Tip
» Let all parts
dry completely
before storing
Page 13
Mainnce & Care
Machine care
For best results, a few simple steps can assure
your machine is well maintained after your
cleaning is complete.
1. Flush your machine of any remaining
residual solution.
a. Fill the 2-in-1 water tank with clean hot
tap water.
b . Recline the handle and press the spray
trigger for 15 seconds while making forward
and backward passes on carpet. Release the
trigger to suction. Repeat for another 15 seconds. Continue without pressing the trigger
until there is no more water being suctioned.
2. Push the power button to turn the machine
off. Unplug the machine and wrap the power
cord. Empty any dirty water or remaining
solution and clean water from the 2-in-1 tank.
3. Rinse out 2-in-1 water tank with hot tap water,
taking care to clean underneath the heavy duty
bladder and all around it.
4. The top half of the tank can be rinsed clean
through the nozzle area. Clear the red filter of
any debris that may have accumulated.
5. Keeping the 2-in-1 water tank off the base of
the machine, simply remove the floor nozzle by
turning the locking keys (see image for location)
to the “unlock” position and lift up. Rinse the
floor nozzle at the faucet.
6. Any loose hair or debris can be pulled from
the brush rolls and thrown away. For the most
thorough clean before storage, follow directions
below for removal and replacement of the brush
rolls and belts on pages 14 and 15.
7. Replace nozzle by lining up the locking keys
with their slots and placing the nozzle and end
caps back onto the foot of the machine. Secure
into place by turning the locking keys to the
“lock” position.
8. To clean attachments that may have been
used, remove from hose and rinse under clean,
running water. Dry and replace attachment in the
hose rack. Clean the hose by suctioning clean
water from the tap. Before replacing, lift end
of hose and stretch out to ensure all water is
cleared from hose. Refer to page 8.
9. To clean the suction diverter, remove the two
screws on the back of the diverter housing. Take
the diverter housing to a sink and rinse it with
water. Take care to remove any debris that may
build up and cause a clog. Replace the diverter
housing and the two screws.
10. After carpet is dry, vacuum again to remove
hair and fuzz.
4.
5. 6.
WARNING
To reduce the risk of electric shock, turn power switch
o and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
9.
Filter
Diverter
www.BISSELL.com
13
Page 14
Mainnce & Care
Drive belt removal & replacement
Occasional replacement of one or both belts
may become necessary. If that is needed, please
follow the instructions below.
1. Turn off the machine, and unplug it from
the outlet.
2. Remove the 2-in-1 water tank. Set aside.
3. Remove the nozzle and end caps by
following the instructions in Step 5 on
page 13.
4. Turn the machine on its side.
IMPORTANT: cord side up.
5. Remove 1 silver screw from the pivot arm.
6. Remove pivot arm by gently lifting up.
7. Remove the drive belt and replace it by
first attaching it to the small drive wheel, then
attach it to the end of the inside brush.
Fluid Connection Point Filter Maintenance
Periodic cleaning of the fluid connection
point in the spray nozzle may be required.
1. To clean the fluid connection point,
remove the nozzle and turn it over.
2. Clean the filter on the end of the fluid
connection point with a small paperclip
and re-attach the nozzle to the machine.
3.
5. 7.
1. 2.
4.
www.BISSELL.com
14
Page 15
Mainnce & Care
Brush removal and brush belt replacement
Brushes can be removed for cleaning or
replacement as needed.
1. Follow drive belt removal Instructions on
page 14.
2. Remove brush rolls by pulling them off of
the metal rods. Be careful not to lose the small
washer at each end of the brush rolls.
3. Replace the brush belt if necessary.
4. Place cleaned or new brush rolls back onto
the rods. Make sure one washer is on each end
of the rollers prior to sliding onto the rod. Be
sure to let the rod slide through the bushing to
insure proper fit.
5. Re-attach the brush belt on the bottom
to the cogs of the small roller brushes.
6. Replace the drive belt by following step 8
on page 14.
7. Place pivot arm in place and screw in place
using the silver screw.
8. Replace nozzle by lining up the locking keys
with their slots and placing the nozzle back onto
the foot of the machine. Secure into place by
turning the locking keys to the “lock” position.
If you have any questions or are having trouble
installing or replacing your belt(s) or brushes,
please call BISSELL Consumer Care.
2.
7.
5.
www.BISSELL.com
15
Page 16
Trbleshting
WARNING
To reduce the risk of electric shock, turn power switch
o and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
Problem Possible causes Remedies
Reduced
spray or
no spray
Water tank may be empty Fill heavy duty bladder with hot
Tank may not be seated
completely
Pump may have lost prime. Turn power OFF and then back ON.
tap water
Turn power OFF. Remove and
reseat tank
Wait one minute, then depress trigger
DirtLifter®
PowerBrush
does not turn
Cleaner
not picking
up solution
The belt is off or broken Turn power OFF and unplug unit
Circuit breaker on machine may
have tripped
Tank may not be seated properly Pick up the 2-in-1 water tank and
Tank may not be assembled
properly
2-in-1 water tank is empty Check fluid levels in heavy-duty
2-in-1 water tank has picked up
maximum dirty water and red
float door has closed.
Red float "door" in the tank may
have closed as a result of bumping
object or moving machine back
and forth too quickly
Red lint screen near air duct
is dirty
from outlet. Follow instructions on
page 15
Turn the machine OFF and unplug
from outlet. Check to see if foreign
object is caught in brush roll.
Remove object. Plug machine in to
reset circuit breaker
re-seat it so it sits snugly on the unit.
Make sure the tank latches on both
sides of the tank are latched properly.
To make sure they are both latched
properly, pick the tank up by its handle.
bladder.
Empty 2-in-1 water tank. Refill heavy
duty bladder with clean hot tap water
and replace.
Turn the machine OFF , allowing red
float door to release an into the open
position. Turn unit back ON to
continue cleaning. Be sure your
forward and backward strokes are
done at a slower pace.
Follow cleaning instructions in
Step 4 on Page 13.
Please do
not return
this product
t o t h e s t o r e .
www.BISSELL.com
16
Other maintenance or service not included in the manual should
be performed by an authorized service representative.
Thank you for selecting a BISSELL product.
For any questions or concerns, BISSELL is happy to
be of service. Contact us directly at 1-800-237-7691.
Page 17
Replacement Parts
These items are available for your BISSELL deep cleaner.
Call 1-800-237-7691 or visit www.BISSELL.com
PART # PART NAME PART # PART NAME
160-0087 Tank Lid (Blackberry Purple)
160-0092 Tank Bottom
160-0097 Tank Cap & Insert Assembly 160-0098 Floor Nozzle with End Cap
203-6845 Float Door 160-0209 Measuring Cup
160-0104 Brush Roll – 6 row (includes 1
Brush, Axle, 2 Swivel Arms)
203-6804 Large Brush Belt (left side) 160-0079 Upper Hose & Cord Wrap
*Not all parts are included with every model.
160-2669 Small Brush Belt (right side)
Assembly
www.BISSELL.com
17
Page 18
Accessories
NOT ALL TOOLS ARE INCLUDED.
These items are available for your BISSELL deep cleaner.
Call 1-800-237-7691 or visit www.BISSELL.com
PART # PART NAME PART # PART NAME
203-6651 3” Tough Stain Tool
203-6653 4” Upholstery Tool 203-6654 6” Stair Tool
203-6655 Spraying Crevice Tool 1603650 3-N-1 Stair Tool
203-7412 Deep Reach Pet Tool 160-0057 Stain Trapper Tool
203-6652 Powered TurboBrush®
Hand Tool
62E5-2 2X Deep Clean and Protect
Formula with Scotchgard™
Protection 60 oz.
89Q5-2 2X Allergen Cleansing
Formula 60 oz.
78H6-3 2X Professional Deep Cleaning
Formula with Scotchgard™
Protection 48 oz.
*Not all parts are included with every model.
99K5-2 2X Pet Stain and Odor
Formula with Scotchgard™
Protection 60 oz.
1052 DeepClean + Refresh
Formula 60 oz.
4001 Stain PreTreat 22 oz.
www.BISSELL.com
18
Page 19
Warrty Service
This warranty gives you specific legal rights, and you may also
have other rights which may vary from state to state. If you need
additional instruction regarding this warranty or have questions
regarding what it may cover, please contact BISSELL Consumer
Care by E-mail, telephone, or regular mail as described below.
Limited Three-Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon
receipt of the product BISSELL will repair or replace (with new or
remanufactured components or products), at BISSELL’s option, free
of charge from the date of purchase by the original purchaser, for
three years any defective or malfunctioning part.
See information below on "If your BISSELL product should
require service".
This warranty applies to product used for personal, and not commercial
or rental service. This warranty does not apply to fans or routine
maintenance components such as filters, belts, or brushes. Damage or
malfunction caused by negligence, abuse, neglect, unauthorized repair,
or any other use not in accordance with the User's Guide is not covered.
BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S
LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM
THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER
WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES
WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO THE THREE YEAR DURATION FROM THE
DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied
warranty last so the above limitation may not apply to you.
NOTE: Please keep your original sales
receipt. It provides proof of date of purchase
in the event of a warranty claim.
If your BISSELL product should
require service:
Contact BISSELL Consumer Care to locate a BISSELL Authorized Service
Center in your area.
If you need information about repairs or replacement parts, or if you
have questions about your warranty, contact BISSELL Consumer Care.
Website or E-mail:
www.BISSELL.com
Call:
BISSELL Consumer Care
1-800-237-7691
Monday – Friday 8am - 10pm ET
Saturday 9am - 8pm ET
Sunday 10am - 7pm ET
www.BISSELL.com
19
Page 20
Regr yr product tod!
Registering is quick, easy and offers you benefits over the lifetime of your product.
BISSELL Rewards Points
Automatically earn points for
discounts and free shipping on
future purchases.
Faster Service
Supplying your information now
saves you time should you need to
contact us with questions regarding
your product.
You’ll receive:
Product Support Reminders
and Alerts
We’ll contact you with any
important product maintenance
reminders and alerts.
Special Promotions
Optional: Register your email
to receive notice of offers,
contests, cleaning tips and more!
Visit www.BISSELL.com/registration now!
BISSELL Csumer Care
For information about repairs or replacement parts, or questions about your warranty:
Call:
BISSELL Consumer Care
1-800-237-7691
Monday - Friday 8 am - 10 pm ET
Saturday 9 am - 8 pm ET
Sunday 10am - 7pm ET
Email:
BISSELL.com/email-us
Visit the BISSELL website: www.BISSELL.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of purchase
date in the event of a warranty claim. See Warranty on page 15 for details.
We c’t wait to ar from y!
Rate this product and let us (and millions
of your closest friends) know what you think!
www.BISSELL.com
©2014 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 160-5266 Rev 09/14
Visit our website at: www.BISSELL.com
20
Scotchgard is a trademark of 3M
Loading...