Biostar TA780G M2+ Owner's Manual

TA780G M2+ Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ............................................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation ............................................. 5

2.1 Installing Central Processing Unit (CPU)....................................... 5

2.2 FAN Headers...................................................................................... 7

2.3 Installing System Memory ................................................................ 8

2.4 Connectors and Slots....................................................................... 10

Chapter 3: Headers & Jumpers Setup .................................. 12

3.1 How to Setup Jumpers .................................................................... 12

3.2 Detail Settings.................................................................................. 12

Chapter 4: RAID Functions ..................................................... 19

4.1 Operation System............................................................................ 19

4.2 Raid Arrays...................................................................................... 19

4.3 How RAID Works............................................................................. 19

Chapter 5: T-Series BIOS & Software ..................................... 22

5.1 T-Series BIOS..................................................................................... 22

5.2 T-Series Software ............................................................................. 30

Chapter 6: Useful Help ............................................................ 33

6.1 Driver Installation Note.................................................................. 33

6.2 AMI BIOS Beep Code....................................................................... 34

6.3 Extra Information............................................................................ 34

6.4 Troubleshooting............................................................................... 35

Appendencies: SPEC In Other Language ................................ 36

German.................................................................................................................. 36

France .................................................................................................................... 38

Italian..................................................................................................................... 40

Spanish ................................................................................................................... 42

Portuguese ............................................................................................................ 44

Polish...................................................................................................................... 46

Russian ................................................................................................................... 48

Arabic..................................................................................................................... 50

Japanese ................................................................................................................ 52

CHAPTER 1: INTRODUCTION

TA780G M2+

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short
circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

1.2 PACKAGE CHECKLIST

HDD Cable X 1
Serial ATA Cable X 2
Serial ATA Power Cable X 1
Rear I/O Panel for ATX Case X 1
User’s Manual X 1
Fully Setup Driver CD X 1
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
S/PDIF out Cable X 1 (optional)
DVI to HDMI Adapter X 1 (optional)

Note: The package contents may differ by area or your motherboard version.

1

Motherboard Manual

1.3 MOTHERBOARD FEATURES

Socket AM2+ / AM2

CPU

FSB

Chipset

Super I/O

Main

Memory

Graphics Integr ated in AMD 78 0G Ch ipset

IDE Int eg r ated IDE Cont ro ller

SATA II Integrated Serial ATA Controller

LAN Realtek RTL 8111C

Sound ALC662

Slots

On Board

Connector

AMD Athlon 64 / Athlon 64 FX / Athlon 64 x2

/ Sempron / Phenom p rocessors

Support HyperTransport 3.0

Supports up to 5.2 GT/s Bandwidth

AMD 780G

AMD SB700

ITE 8718F

Prov ides the mos t co mmonly used legac y

Super I/O functionality

DDR2 DIMM Slots x 4

Max Memory Capacity 8GB

Each DIMM supports 256/512MB/1GB/2GB

DDR2

PCI Express Gen2 x16 slot x1 Supports PCI-E Gen2 x16 expansion cards

PCI Express Gen2 x1 slot x1 Supports PCI-E Gen2 x1 expansion cards

PCI slot x2 Supports PCI expansion cards

Floppy connector x1 Each connector supports 2 Floppy drives

IDE Connector x1 Each connector supports 2 IDE device

SATA Connector x6 Each connector supports 1 SATA devices

Front Panel Connector x1 Supports front panel facilit ies

Front Audio Connector x1 Supports front panel audio function

SPEC

AMD 64 Architecture enables 32 and 64 b it

computing

Supports Hyper Transport 3.0 and Cool=n=Quiet

Low Pin Count Interface

En viro nment Cont rol in it iatives

H/W Mon itor

ITE's "S mart Guard ian" funct ion

Dual Channe l Mod e DDR2 me mory modu le

Supports DDR2 533 / 667 / 800

Supports DDR2 1066 (for AM2+ CPU on ly)

Register ed DIMM and ECC D IMM is not suppo rted

Max S hared Vid eo Memory is 51 2 MB

DX10 support

HDCP / UVD support

Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode

supports PIO Mode 0~4,

Data transfer rates up to 3 Gb/s

SATA Versio n 2. 0 s pecif icat ion co mplian t

10 / 100 / 1000 Mb/s auto negotiation

Half / Full duplex capability

5.1 channels audio out

High Definition Audio

2

SPEC

CD-in Connector x1 Supports CD audio-in function

S/PDIF out connector x1 Supports digital audio out function

CPU Fan header x1 CPU Fan power supply (with Smart Fan function)

System Fan head er x1 Sys tem Fan Po wer supply

CMOS clear header x1 Restore CMOS data to factory default

USB connector x3 Each connector s upports 2 front panel USB po rts

Power Connector (24pin) x1 Connects to Power supply

Power Connector (4pin) x1 Connects to Power supply

Printer Port Connector x1 Each connector supports 1 Printer port

Serial port Connector x1 Connects to RS-232 Port

PS/2 Keyboard x1

PS/2 Mous e x1

Back Panel

I/O

Board Size 215 mm(W) x 244 mm(L)

Special

Features

OS Support Windows XP / VISTA

DVI port x1

VGA port x1

LAN port x1

USB Port x4

Audio Jack x3

RAID 0 / 1 / 1+0 support

HyperFlash support

1.4 R

EAR PANEL CONNECTORS

TA780G M2+

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to DVI-D monitor

Connect to D-SUB monitor

Connect to RJ-45 ethernet cab le

Connect t o USB devices

Provide Audio-In/Out and microphone connection

Biostar Reserves the right to add or remove support

for any OS With or without notice.

PS/2
Mou se

PS/2
Keyboard

VGA

DVI-D

LAN

Line In/
Surr ound

Line Out

Mic In 1/
Bass/ Center

USB X2USBX2

3

Motherboard Manual

1.5 MOTHERBOARD LAYOUT

JKBMS1

JATXP WR2

VGA

JCFAN1

DVI

JUSB1

JUS BLAN1

JAUDIO1

JC DIN1

Codec

JUSBV1

JAUDIOF1

LAN

Sup er I/O

JCO M1

Note: represents the 1■

PEX1 _1

JPRNT1

JSPDIF_OUT1

PEX16_ 1

PC I1

PC I2

AMD

780G

FDD1

st

pin.

Socket AM2+

JUS B4

JUSB3 JUSB2

AMD

SB7 00

DIMMA1

JU SBV 2

DIMMB1

SATA3

SATA 1

DIMMA2

JATXPWR1

DIMMB2

SATA 5 SA TA6

JCMOS1

JPANEL1

BATTERY

BIOS

SATA 2

IDE1

JSFA N1

SATA4

4

CHAPTER 2: HARDWARE INSTALLATION

TA780G M2+

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Remove the socket protection cap.

Step 2: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 3: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.

5

Motherboard Manual

Step 4: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the JCFAN1. This completes the installation.

Note: Please update the BIOS to the latest version while using AM2+ CPUs. Due to the latest CPU

transition, you may encounter the situation that the new system failed to boot while using new
AM2+ CPUs. In this case, please install one standard AM2 CPU to boot your system, and
update the latest BIOS from our website for AM2+ CPUs support.

6

TA780G M2+

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufact urer.
Connect the fan cable to the connector while matching the black wire to
pin#1.

JCFAN1: CPU Fan Header

4

1

JSFAN1: System Fan Header

13

Pin

Assignment

1 Ground
2 +12V
3

FAN RPM r at e
sense

4 Smart Fan

Control (By Fan)

Pin

Assignment

1 Ground
2 +12V
3 FAN RPM rate

sense

Note:

The JCFAN1 supports 4-pin head connector. The JSFAN1 supports 3-pin head
connector. When connecting with wires onto connectors, please note that the red wire is

the positive and should be connected to pin#2, and the black wire is Ground and should
be connected to GND.

7

Motherboard Manual

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DIMMB1

DIMMA1

DIMMA2

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.

DIMMB2

2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.

8

TA780G M2+

B. Memory Capacity

DIMM Socket

Location

DIMMA1 256MB/512MB/1GB/2GB

DIMMB1 256MB/512MB/1GB/2GB

DIMMA2 256MB/512MB/1GB/2GB

DIMMB2 256MB/512MB/1GB/2GB

DDR2 Module

Total M emory

Size

Max is 8GB.

C. Dual Channel Memory installation

To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:

Install memory module of the same density in pairs, shown in the following
table.

Dual Channel Status

Enabled O O X X

Enabled X X O O

Enabled O O O O

DIMMA1

DIMMB1

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or
x16)

DIMMA2

DIMMB2

9

Motherboard Manual

3

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cable.

234

IDE1: Hard Disk Connectors

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.

The IDE connectors can connect a master and a slave drive, so you can
connect up to two hard disk drives.

13

21

3940

10

TA780G M2+

PEX16_1: PCI-Express Gen2 x16 Slot

- PCI-Express 2.0 compliant.

- Maximum theoretical realized bandwidth of 8GB/s simultaneously per

direction, for an aggregate of 16GB/s totally.

PEX1_1: PCI-Express Gen2 x1 Slot

- PCI-Express 2.0 compliant.

- Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total.

- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

- 2X bandwidth over the PCI-Express 1.0 architecture.

PE X1_1

PEX16_1

PCI1~PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

PCI1

PCI2

11

Motherboard Manual

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

JPANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.

PWR_LED

On/Off

-

9
1

++

SPK

HLED

16

8

-

+

RS T

12

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A
2 N/A 10 N/A
3 N/ A 11 N/A N/A
4 Speaker
5 HDD LED (+) 13 Power LED (+)
6 HDD LED (-)
7 Ground 15 Power button
8 Reset control

Speaker
Connector

Hard drive
LED

Reset button

12 Power LED (+)

14 Power LED (-)

16 Ground

N/A

Power LED

Power-on button

TA780G M2+

JATXPWR1: AT X Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX
power supply.

12

1

Pin Assignment Pin Assignm ent

13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V

24

13

JATXPWR2: AT X Power Source Connector

By connecting this connector, it will provide +12V to CPU power circuit.

34

12

Pin

Assignment

1 +12V
2 +12V
3 Ground
4 Ground

13

Motherboard Manual

JUSB2/JUSB3/JUSB4: Headers for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.

JUSB4
JUSB3 JUSB2

210

19

SATA1~SATA6: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 6 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

SATA5 SATA6
SATA3 SATA4
SATA1 SATA2

Assignment

Pin

1 +5V (fused)
2 +5V (fused)
3 USB­4 USB­5 USB+
6 USB+
7 Ground
8 Ground
9 NC

10 Key

Assignment

Pin

1 Ground
2 TX+
3 TX­4 Ground
5 RX­6 RX+
7 Ground

14

7

14

TA780G M2+

JSPDIF_OUT1: Digital Audio-out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

Pin

Assignment

1 +5V
2 SPDIF_OUT
3 Ground

13

JAUDIOF1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.

Pin Assignment

1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO

10

9

1

2

5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in

10 Jack Sense

15

Motherboard Manual

JCDIN1: CD-ROM Audio-in Connector

This connector allows user to connect the audio source from the variaty devices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.

13

Pin

1 Left Channel

1

2 Ground
3 Ground
4 Right Channel

4

13

Pin 1-2 Close:

Normal Operation
(default).

13

Pin 2-3 Close:

Clear CMOS data.

Assignment

Input

Input

16

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

TA780G M2+

JPRNT1: Printer Port Connector

This header allows you to connector printer on the PC.

2

125

Pin Assignment Pin Assignment

1 -Strobe 14 Ground
2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7
5 Data 1 18 Ground
6 -Init 19 -ACK
7 Data 2 20 Ground
8 -Scltin 21 Busy

9 Data 3 22 Ground
10 Ground 23 PE
11 Data 4 24 Ground
12 Ground 25 SCLT
13 Data 5 26 Key

JCOM1: Serial port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Pin

Assignment

1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal ready
5 Signal ground
6 Data set ready
7 Request to send

210

19

8 Clear to send
9 Ring indicator

10 NC

17

Motherboard Manual

JUSBV1/JUSBV2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBV1: +5V for USB ports at JUSB1/JUSBLAN1.
JUSBV2: +5V for USB ports at front panel (JUSB2/JUSB3/JUSB4).

Pin 2-3 Close:

JUSBV1: +5V STB for USB ports at JUSB1/JUSBLAN1.
JUSBV2: +5V STB for USB ports at front panel (JUSB2/JUSB3/JUSB4).

JUSBV1

1

3

13

JUSBV2

1

3

1

3

13

Pin 1-2 close

13

Pin 2-3 close

18

CHAPTER 4: RAID FUNCTIONS

TA780G M2+

4.1 O

z Supports Windows XP Home/Professional Edition, and Windows Vista.

PERATION SYSTEM

4.2 RAID ARRAYS

RAID supports the following types of RAID arrays:

RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for

many applications.

RAID 1: RAID 1 defines techniques for mirroring data.

RAID 1+0: RAID 1+0 combines the techniques used in R AID 0 and RAID 1.

4.3 HOW RAID WORKS

RAID 0:

The controller “stripes” data across multip le drives in a RAID 0 array system. It breaks
up a large file into smaller b locks and performs disk reads and writes across multiple
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment.
This technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

- Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the
platform.

- Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.

- Benefits: provides increased data throughput, especially for large files.
No capacity loss penalty for parity.

- Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.

- Fault Tolerance: No.

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

19

Motherboard Manual

RAID 1:

Every read and write is actually carr ied out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on
a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if
the active volume or drive is corrupted or becomes unavailable because of a hardware
failure.

RAID techniques can be applied for high-ava ilability solutions, or as a form of
automatic backup that eliminates tedious manual backups to more expensive and less
reliable media.

Features and Benefits

- Drives: Minimum 2, and maximum is 2.

- Uses: RAID 1 is ideal for small databases or any other application that

requires fault tolerance and minimal capacity.

- Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.

- Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.

- Fault Tolerance: Yes.

20

Block 1
Block 2
Block 3

Block 1
Block 2
Block 3

TA780G M2+

RAID 1+0:

RAID 1 drives can be stripped usin g RAID 0 techniques. Resulting in a RAID 1+0
solution for improved resiliency, performance and rebuild performance.

Features and Benefits

- Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.

- Benefits: Optimizes for both fault tolerance and performance, allowing for

automatic redundancy. May be simultaneously used with other RAID
levels in an array, and allows for spare disks.

- Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.

- Fault Tolerance: Yes.

Block 1
Block 3
Block 5

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

Block 2
Block 4
Block 6

21

Motherboard Manual

CHAPTER 5: T-SERIES BIOS & SOFTWARE

5.1 T-S

ERIES BIOS

T-Series BIOS Features

Overclocking Navigator Engine (O.N.E.)

Memory Integration Test (M.I.T., under Overclock Navigator Engine)

BIO-Flasher: Update BIOS file from USB Flash Drive or FDD

Self Recovery System (S.R.S)

Smart Fan Function

!! WARNING !!

For better system performance, the BIOS firmware is being
continuously updated. The BIOS information described below in
this manual is for your reference only and the actual BIOS
information and settings on board may be different from this
manual. For further information of setting up the BIOS, please
refer to the BIOS Manual in the Setup CD.

A. Overclocking Navigator Engine (O.N.E.)

ONE provides two powerful overclocking engines: MOS and AOS for both
Elite and Casual overclockers.

Main Advanced

T-Series Settings

WARNING: Setting wrong values in below sections
may cause system to malfunction.

OverClock Navigator [Normal]

=========== Automate OverClock System ===========

Auto OverClock System [V6-Tech Engine]

============ Manual OverClock System ============

CPU Overvoltage [StartUp]
Memory Overvoltage [1.95V]
Chipset Overvoltage [1.15V]
HT Overvoltage [1.20V]
CPU Frequency [200]
> Memory Configuration
> DRAM Timing Configuration
> Hyper Transport Configuration

Integrated Memory Test [Disabled]

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

PCIPnP Boot

BIOS SETUP UTILITY

Chipset T-Series

Exit

Options

Normal
Automate OverClock
Manual OverClock

Select Screen
Select Item
Change Option

+-

General Help

F1

Save and Exit

F10

Exit

ESC

22

Manual Overclock System (M.O.S.)

MOS is designed for experienced overclock users.
It allows users to customize personal overclock settings.

Main Advan ced P CIPnP Boot Chipset T-Ser ies

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Normal]

===== ====== Automate Over Clock System ==== =======

Auto OverClock Sys tem [V6-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O vervoltage [StartUp]
Memor y Overvoltage [1.95V]
Chips et Overvoltag e [1.15V]
HT Ov ervoltage [1.20V]
CPU Frequency [200]
> Mem ory Configura tion
> DRA M Timing Conf igurati on
> Hyp er Transport Configu ration

Integ rated Memory Test [Disabled ]

vxx.xx (C )Copyright 19 85-200x , American Me gatrends, Inc .

Main Advan ced P CIPnP Boot Chipset T-Ser ies

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Manual O verClock]

===== ====== Automate Over Clock System ==== =======

Auto OverClock Sys tem [V6-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O vervoltage [StartUp]
Memor y Overvoltage [1.95V]
Chips et Overvoltag e [1.15V]
HT Ov ervoltage [1.20V]
CPU Frequency [200]
> Mem ory Configura tion
> DRA M Timing Conf igurati on
> Hyp er Transport Configu ration
Integ rated Memory Test [Disabled ]

vxx.xx (C )Copyright 19 85-200x , American Me gatrends, Inc .

CPU Overvoltage

This function will increase CPU stability when overclocking. However, the
CPU temperature will increase when CPU voltage is increased.

Memory Overvoltage

This function will increase memory stability when overclocking.

Chipset Overvoltage

This function will increase Northbridge and Southbridge chipset stability
when overclocking.

HT Overvoltage

This function will increase CPU stability when overclocking the HT ratio.

BIOS SE TUP UTILITY

Op tions
Normal
Automat e OverClock

Manual OverC lock

↓

BIOS SE TUP UTILITY

Op tions

Normal
Automate Ove rClock
Manual Ov erClock

+­F1
F10
ESC

Op tions

Normal
Automate Ove rClock
Manual Ov erClock

+­F1
F10
ESC

TA780G M2+

Exit

Select Sc reen
Select It em
Change Op tion
General H elp
Save and Exit
Exit

Exit

Select Sc reen
Select It em
Change Op tion
General H elp
Save and Exit
Exit

23

Motherboard Manual

CPU Frequency

CPU Frequency is directly in proportion to system performance. To
maintain the system stability, CPU voltage needs to be increased also
when raising CPU frequency.

Memory Co nf ig urat io n

Enter this function for more advanced memory settings.

DRAM Timing Conf iguration

Enter this function for more advanced DRAM clock settings.

Hyper Transport Conf ig uratio n

Enter this function for more advanced Hyper Transport settings.

Automatic Overclock System (A.O.S.)

For beginners in overclock field, BET had developed an easy, fast, and
powerful feature to increase the system performance, named A.O.S.

Based on many tests and experiments, A.O.S. provides 3 ideal overclock
configurations that are able to raise the system performance in a single
step.

Main Advanced PCIPnP Boot Chipset T-Ser ies

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Normal]

===== ====== Automate Over Clock System ==== ====== =

Auto OverClock Sys tem [V6-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O vervoltage [StartUp]
Memor y Overvoltage [1.95V]
Chips et Overvoltag e [1.15V]
HT Ov ervoltage [1.20V]
CPU Frequency [200]
> Mem ory Configura tion
> DRA M Timing Conf igurati on
> Hyp er Transport Configu rati on

Integ rated Memory Test [Disabled ]

BIOS SE TUP UTILITY

Op tions
Normal

Automat e OverClock

Manual OverC lock

vxx.xx (C )Copyright 19 85-200x , Amer ican Me gatrends, Inc .

Exit

Op tions

Normal
Automate Ove rClock
Manual Ov erClock

Select Sc reen
Select It em
Change Op tion

+-

General H elp

F1

Save and Exit

F10

Exit

ESC

24

V6 Tech Engine

This engine will make a good over-clock performance.

Main Advanced PCIPnP Boot Chipset T-Ser ies

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Automate OverClock ]

===== ====== Automate Over Clock System ==== ====== =

Auto OverClock Sys tem [V6-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O vervoltage [StartUp]
Memor y Overvoltage [1.95V]
Chips et Overvoltag e [1.15V]
HT Ov ervoltage [1.20V]
CPU Frequency [200]
> Mem ory Configura tion
> DRA M Timing Conf igurati on
> Hyp er Transport Configu rati on

Integ rated Memory Test [Disabled ]

vxx.xx (C )Copyright 19 85-200x , Amer ican Me gatrends, Inc .

BIOS SE TUP UTILITY

V8 Tech Engine

This engine will make a better over-clock performance.

Main Advanced PCIPnP Boot Chipset T-Ser ies

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Automate OverClock ]

===== ====== Automate Over Clock System ==== ====== =

Auto OverClock Sys tem [V8-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O vervoltage [StartUp]
Memor y Overvoltage [1.95V]
Chips et Overvoltag e [1.15V]
HT Ov ervoltage [1.20V]
CPU Frequency [200]
> Mem ory Configura tion
> DRA M Timing Conf igurati on
> Hyp er Transport Configu rati on

Integ rated Memory Test [Disabled ]

vxx.xx (C )Copyright 19 85-200x , Amer ican Me gatrends, Inc .

BIOS SE TUP UTILITY

V12 Tech Engine

This engine will make a best over-clock performance.

Main Advanced PCIPnP Boot Chipset T-Ser ies

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Automate OverClock ]

===== ====== Automate Over Clock System ==== ====== =

Auto OverClock Sys tem [V12-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O vervoltage [StartUp]
Memor y Overvoltage [1.95V]
Chips et Overvoltag e [1.15V]
HT Ov ervoltage [1.20V]
CPU Frequency [200]
> Mem ory Configura tion
> DRA M Timing Conf igurati on
> Hyp er Transport Configu rati on

Integ rated Memory Test [Disabled ]

vxx.xx (C )Copyright 19 85-200x , Amer ican Me gatrends, Inc .

BIOS SE TUP UTILITY

TA780G M2+

Exit

Op tions

Normal
Automate Ove rClock
Manual Ov erClock

Select Sc reen
Select It em
Change Op tion

+-

General H elp

F1

Save and Exit

F10

Exit

ESC

Exit

Op tions

Normal
Automate Ove rClock
Manual Ov erClock

Select Sc reen
Select It em
Change Op tion

+-

General H elp

F1

Save and Exit

F10

Exit

ESC

Exit

Op tions

Normal
Automate Ove rClock
Manual Ov erClock

Select Sc reen
Select It em
Change Op tion

+-

General H elp

F1

Save and Exit

F10

Exit

ESC

25

Motherboard Manual

Notices:

1. Not all types of AMD CPU perform above overclock setting ideally; the difference will be based
on the selected CPU model.

B. Memory Integration Test (M.I.T.)

This function is under “Overclocking Navigator Engine” item.
MIT allows users to test memory compatibilities, and no extra devices or

software are needed.

Step 1

The default setting under this item is “Disabled”; the condition parameter should
be changed to “Enable” to proceed this test.

Main Advance d PCIPnP Boot Chipset T -Series

T-Ser ies Settings

WARNI NG: Setting wrong values i n below section s
may cause sys tem to ma lfunction.

OverC lock Navigator [N ormal]

===== ====== Automate O verClock System ======== ===

Auto OverClock System [V 6-Tech Engine]

===== ======= Manual Ov erClock S ystem ========= ===

CPU O vervoltage [S tartUp]
Memor y Overvoltage [1 .95V]
Chips et Overvoltage [1 .15V]
HT Ov ervoltage [1 .20V]
CPU Frequency [2 00]
> Mem ory Configuration
> DRA M Timing Configur ation
> Hyp er Transport Conf iguration

Integ rated Memory Test [D isabled]

vxx.xx (C)Copyright 19 85-200x, Am erican Megatren ds, Inc.

Main Advance d PCIPnP Boot Chipset T -Series

T-Ser ies Settings

WARNI NG: Setting wrong values i n below section s
may cause sys tem to ma lfunction.

OverC lock Navigator [N ormal]

===== ====== Automate O verClock System ======== ===

Auto OverClock System [V 6-Tech Engine]

===== ======= Manual Ov erClock S ystem ========= ===

CPU O vervoltage [S tartUp]
Memor y Overvoltage [1 .95V]
Chips et Overvoltage [1 .15V]
HT Ov ervoltage [1 .20V]
CPU Frequency [2 00]
> Mem ory Configuration
> DRA M Timing Configur ation
> Hyp er Transport Conf iguration

Integ rated Memory Test [E nabled]

vxx.xx (C)Copyright 19 85-200x, Am erican Megatren ds, Inc.

Step 2

Save and Exit from CMOS setup and reboot the system to activate this test.
Run this test for 5 minutes (minimum) to ensure the memory stability.

Step 3

When the process is done, change the setting back from “Enable” to “Disable”
to complete the test.

BIOS SETUP UTILITY

↓

BIOS SETUP UTILITY

Exit

Opti ons

Normal
Automate Ov erClock
Manual Over Clock

Select Scree n
Select Item

+-

Change Optio n
General Help

F1
F10

Save an d Exit
Exit

ESC

Exit

Opti ons

Normal
Automate Ov erClock
Manual Over Clock

Select Scree n
Select Item

+-

Change Optio n
General Help

F1
F10

Save an d Exit
Exit

ESC

26

C. BIO-Flasher

BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.

The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIO-Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, save the BIOS file into a USB pen drive or a floppy disk.

3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.

4. Power on or reset the computer and then
press <F12> during the POST process.
A select dialog as the picture on the right
appears.
Select the device contains the BIOS file and
press <Enter> to enter the utility.

TA780G M2+

5. The utility will show the BIOS
files and their respective
information. Select the proper
BIOS file and press <Enter>
then <Y> to perform the BIOS
update process.

6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.

z This utility only allows storage device with FAT32/16 format and single

parti tion.

z Shutting down or resetting the system while updating the B IOS will lead to

system boot failure.

27

Motherboard Manual

D. Self Recovery System (S.R.S.)

This function can’t be seen under BIOS setup; and is always on whenever the
system starts up.

However, it can prevent system hang-up due to inappropriate overclock
actions.

When the system hangs up, S.R.S. will automatically log in the default BIOS
setting, and all overclock settings will be re-configured.

E. Smart Fan Function

Smart Fan Function is under “Smart Fan Configuration” in “Advanced Menu”.
This is a brilliant feature to control CPU/System Temperature vs. Fan speed.
When enabling Smart Fan function, Fan speed is controlled automatically by
CPU/System temperature.
This function will protect CPU/System from overheat problem and maintain the
system temperature at a safe level.

Main Advanced

WARNING: Setting wrong values in below sections
may cause system to malfunction.

> CPU Configuration
> SuperIO Configuration

> Smart Fan Configuration

> Hardware Health Configuration
> ACPI Configuration
> USB Configuration

MPS Revision [1.4]

PCIPnP Boot

BIOS SETUP UTILITY

Chipset T-Series

Configure CPU.Advanced Settings

Select Screen
Select Item
Go to Sub Screen

Enter

General Help

F1

Save and Exit

F10

Exit

ESC

Exit

28

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

↓

Advanced

Smart Fan Configuration

CPU Smart Fan [Disabled]

Smart Fan Calibration
Control Mode
Fan Ctrl OFF( C)

Fan Ctrl On( C)
Fan Ctrl Start value
Fan Ctrl Sensitive

o

o

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

BIOS SETUP UTILITY

When you choice [Auto]
,[3Pin] or [4Pin],
please run the
calibration to define
the Fan parameters for
Smart Fan control

Select Screen
Select Item
Change Option

+-

General Help

F1

Save and Exit

F10

Exit

ESC

TA780G M2+

Smart Fan Calibration

Choose this item and then the BIOS will automatically test and detect the
CPU/System fan functions and show CPU/System fan speed.

Control Mode

This item provides several operation modes of the fan.

Fan Ctrl OFF(℃)

If the CPU/System temperature is lower than the set value, the CPU/
System fan will turn off. The range is from 0~127, with an interval of 1.

Fan Ctrl On(℃)

The CPU/System fan starts to work when CPU/System temperature
arrives to this set value. The range is from 0~127, with an interval of 1.

Fan Ctrl Start Value

When CPU/System temperature arrives to the set value, the CPU/System
fan will work under Smart Fan Function mode. The range is from 0~127,
with an interval of 1.

Fan Ctrl Sensitive

Increasing the value of slope PWM will raise the speed of CPU/System fan.
The range is from 1~127, with an interval of 1.

29

Motherboard Manual

5.2 T-SERIES SOFTWARE

Installing T-Series Software

1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.

2. Select Software In stallation, and then click on the respective software
title.

3. Follow the on-screen instructions to complete the installation.

Launching T-Series Software

After the installation process, you will see
the software icons appear on the desktop.
Double-click the icon to launch T-Series utility.

Hardware Monitor

HW Monitor is a monitor utility that helps you to maintain the health of the PC.
It provides real-time information of CPU/GPU/System temperat ure, fan speed,
and voltage.

Thi s area sh ows vol t age i nfor mati on

Vol t age Pa nel Fan Pa nel

Thi s area sh ows CPU in f orma tion

Thi s area s hows CPU/ Syst em t emp erat ure

30

Tu rn t o Fa n Pa nel

Thi s area sh ows CPU/ Syst em f an spe ed

Turn to Voltage Panel

TA780G M2+

e

eHot-Line (Optional)

eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.

Before you use this uti lity, please set Outlook Express as your default e-mail c lient app licatio n progra m.

rep resents important

*

information t hat you
must provi de. Withou t
this informat ion, you may
not be able to send ou t
the mail.

This block will show
the infor mation which
would be collect ed in
the mail.

Send the mail ou t.

Describe co ndition

*

of your syst em.

Save these information to a .txt fil

Exit this dialog.

Select your area or

*

the area clos e to yo u.

Provid e the e-mail
addres s that you woul d
like to send the copy to.

Provide t he name of

*

the memory module
manufactu rer.

Provid e the name of
the power supply
manufac turer and the
model no .

After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialog appears asking you to enter file name.

31

Motherboard Manual

Enter the file name and then click
“Save”. Your system information

will be saved to a .txt file.

We will not share customer’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.

Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.

32

If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web

http://www.biostar.com.tw/app/en-us/about/contact.php for getting

our contact information.

CHAPTER 6: USEFUL HELP

TA780G M2+

6.1 D

RIVER INSTALLATION NOTE

After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.

You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader so ftware from
http://www.adobe.com/products/acrobat/readstep2.html

33

Motherboard Manual

6.2 AMI BIOS BEEP CODE

Beep Sound Meaning

One short beep VGA detected

One long beep followed by two short
beeps then a pause

One long beep followed by three short
beeps

One long beep followed by four short
beeps

6.3 EXTRA INFORMATION

CPU Overheated

If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection
function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

Quick boot set to disabled
No keyboard detected

No memory detected

No VGA detected

Hardware component failure

34

6.4 TROUBLESHOOTING

Probable Solution

1. No power to the system at all
Power light don’t illuminate, fan
inside power supply does not turn
on.

2. Indicator light on keyboard does
not turn on.

System inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drive is spinning.

System does not boot from hard disk
drive, can be booted from optical drive.

System only boots from optical drive.
Hard disk can be read and applications
can be used but booting from hard disk
is impossible.

Screen message says “Invalid
Configuration” or “CMOS Failure.”

Cannot boot system after installing
second hard drive.

TA780G M2+

1. Make sure power cable is
securely plugged in.

2. Replace cable.

3. Contact technical support.

Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.

1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.

2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.

1. Back up data and applications
files.

2. Reformat the hard drive.
Re-install applications and data
using backup disks.

Review system’s equipment. Make sure
correct information is in setup.

1. Set master/slave jumpers
correctly.

2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

35

Motherboard Manual

APPENDENCIES: SPEC IN OTHER LANGUAGE

G

ERMAN

Sp ezif ika tio nen

Sockel AM2+ / AM2

CPU

FSB

Chipsatz

Super E/A

Arbeitsspeich

er

Grafik Integrierter AMD 780G-Chipsatz

IDE Integ r iert er IDE - Con tro ller

SATA Integrierter Serial ATA-Controller

LAN Realtek RTL 8111C

HD

Audio-Unters

tützung

Steckplätz e

AMD Athlon 64 / Ath lon 64 FX / Althlon 64

X2 / S empron / Ph enom Prozess oren

Unterstützt HyperTransport 3.0 mit einer

Bandbreite von bis zu 5.2 GT/s

AMD 780G

AMD SB700

ITE8718F

Biet et die h äuf ig verwendeten alten Sup er

E/A-Funktionen.

DDR2 DIMM-Steckplätze x 4

Max. 8GB Arbeitsspeicher

Jeder DIMM unterstützt

256/512MB/1GB/2GB DDR2.

ALC662

PCI Express Gen2 x16 Steckplatz x1

PCI Express Gen2 x1 Steckplatz x1

PCI-Steckp latz x2

36

Die AMD 64-Archit ektur unterstützt eine 32- Bit- und

64-Bit-Datenverarbeitung

Unterstützt Hyper Transport 3.0 und Cool’n’Quiet

Low Pin Count-Schnittstelle

Umgebungskontrolle,

Hardware-Überwachung

"Smart Guardian"-Funktion von ITE

Dual-Kanal DDR2 Speichermodul

Unterstützt DDR2 533 / 667 / 800

Unterstützt DDR2 1066 (for AM2+ CPU only)

registrierte DIMMs. ECC DIMMs werden nicht

unterstützt.

Max. 512MB gemeinsam benutzter Videospeicher

Unterstützt DX10

Unterstützt HDCP / UVD

Ultra DMA 33 / 66 / 100 / 133 Bus Master-Modus

Unterstützt PIO-Modus 0~4,

Datentransferrate b is zu 3 Gb /s

Konform mit der SATA-Spezifikation Version 2.0.

10 / 100 /1000 Mb/s Auto-Negotiation

Halb-/ Vollduplex-Funktion

5.1-Kanal-Audioausgabe

Unterstützt High-Definition Audio

Onboard-Ans

chluss

Rückseiten-E

/A

Platinengröß

e

Sonderfunkti

onen

OS-Unterstü

tzung

TA780G M2+

Sp ezif ika tio nen

Diskettenlaufwerkanschluss x1 Jeder Anschluss unterstützt 2 Diskettenlaufwerke

IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke

SATA-Anschluss x6 Jeder Anschluss unterstützt 1 SATA-Laufwerk

Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen

Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion

CD-IN-Anschluss x1 Unterstützt die CD Audio-In-Funktion

S/PDIF- Ausgangsanschluss x1 Unterstützt die digitale Audioausgabefunktion

CPU-Lüfter-Sockel x1

System-Lüfter-Sockel x1 System-Lüfter-Stromversorgungsanschluss

"CMOS löschen"-Sockel x 1

USB-Anschluss x3

Stromanschluss (24-polig) x1

St romansch luss (4- p olig ) x1

Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss

Serieller Anschluss x1

PS/2-Tastatur x1

PS/2-Maus x1

VGA-Anschluss x1

LAN-Anschluss x1

USB-Anschluss x4

Audioanschluss x3

DVI-Anschluss x1

215 mm (B) X 244 mm (L)

Unterstützt RAID 0 / 1 / 1+0

Unterstützt HyperFlash

Windows XP / VISTA

CPU-Lüfterstromversorgungsanschluss (mit Smart

Fan -F un ktio n)

Jeder Anschluss unterstützt 2

Fronttafel-USB-Anschlüsse

Biostar behält s ich das Recht vor, ohne Ankünd igung

die Unterstützung für ein Betriebssystem

hinzuzufügen oder zu entfernen.

37

Motherboard Manual

FRANCE

Socket AM2+ / AM2

UC

Bus frontal

Chipset

Super E/S

Mémoire

principale

Graphiques Integré dans la chipset AMD 780G

IDE Contrôleur IDE intégré

SATA

LAN Realtek RTL 8111C

Prise en

charg e

aud io HD

Fentes

Connecteur

embarqu é

Processeurs AMD Athlon 64 / Athlon 64 FX

/ Alth lon 64 X2 / Sempron / Pheno m

Prend en charge Hyp er Transport 3.0

jusqu'à une bande passante de 5.2 GT/s

AMD 780G

AMD SB700

ITE 8718F

Fournit la fonctionnalité de Super E/S

patrimoniales la plus utilisée.

Fentes DDR2 DIMM x 4

Capacit é mémo ir e max ima le de 8 Go

Chaque DIMM prend en charge des DDR2

de 256/512 Mo et 1Go/2Go

Contrô leur Serial ATA int é gr é

ALC662

Fente PCI Express Gen2 x16 x1

Fente PCI Express Gen2 x1 x1

Fente PCI x2

Connecteur de disquette x1

Connecteur IDE x1

Connecteur SATA x6

SPEC

L'architecture AMD 64 permet le calcul 32 et 64 bits

Prend en cha rge Hyp er Transport 3.0 et Coo l’n’Quiet

Int e rfa ce à faib le co mpte de b roches

Initiatives de contrôle environnementales,

Mon iteur d e mat ériel

Fonction "Gardien intelligent" de l'ITE

Module d e mémoire DD R2 à mod e à doub le vo ie

Prend en charge la DDR2 533 / 667 / 800

Prend en charge la DDR2 1066 (for AM2+ CPU only)

Les DIMM à registres et DIMM avec code correcteurs

d'erreurs ne sont pas prises en charge

Mémoire vidéo partagée maximale de 512 Mo

Prise en charge DX10

Prise en charge HDC P / UVD

Mode principale de Bus Ultra DMA 33 / 66 / 100 / 133

Prend en charge le mode PIO 0~4,

Taux de transfert jusqu'à 3 Go/s.

Co nfo rme à la s pécif icat ion SATA Vers ion 2.0

10 / 100 /1000 Mb/s négociation automatique

Half / Full duplex capability

Sortie aud io à 5.1 vo ies

Prise en charge de l'audio haute déf inition

Chaque co nne ctor prend en ch arg e 2 lecteu rs de

disquettes

Chaque connecteur prend en ch arg e 2 périphériqu es

IDE

Chaque connecteur prend en ch arg e 1 périphériqu e

SATA

38

Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant

Connecteur Audio du panneau avant x1 Prend en charge la fonct ion audio du panneau avant

Connecteur d' entrée CD x 1 Prend en charge la fonct ion d'ent rée audio de CD

Connecteur de sortie S/PDIF x1 Prend en charge la fonction de sortie audio numérique

Embase de ventilateur UC x1

Embase de ventilateur système x1 Alimentation électrique du ventilateur système

Embase d'effacement CMOS x1

Connecteur USB x3

Connecteur d' aliment at ion x1

(24 broches)

Connecteur d' aliment at ion x1

(4 broch es)

Connecteur de Port d'imprimante x1

Connecteur de Port série x1

Clavier PS/2 x1

Souris PS/2 x1

E/S du

panneau

arrière

Dimension

s de la

cart e

Fonctionnal

ité s

spéciales

Support SE Windows XP / VISTA

Port VGA x1

Port LAN x1

Port USB x4

Fiche aud io x3

Port DVI x 1

215 mm (l) X 244 mm (H)

Prise en charge RAID 0 / 1 / 1 +0

Prise en charge HyperFlash

TA780G M2+

SPEC

Alimentation électrique du ventilateur UC (avec

fonction de ventilateur intelligent)

Chaque connecteur prend en charge 2 ports USB de

panneau avant

Chaque co nne ctor prend en ch arg e 1 Port

d'imprimante

Biostar se réserve le droit d'ajouter ou de supprimer le

support de SE avec ou sans préavis.

39

Motherboard Manual

ITALIAN

Socket AM2+ / AM2

CPU

FSB

Chipset

Super I/O

Memor ia

principale

Grafica Integrata nel Chipset AMD 780G

IDE Con troller IDE int eg rato

SATA Controller Serial ATA integrato

LA N Realtek RTL 8111C

Supporto

audio HD

Allo g gi

Connettori

su scheda

Processori AMD Athlon 64 / Athlon 64 FX

/ Althlon 64 X2 / Sempron / Phenom

Supporto di HyperTransport 3.0 fino a

5.2 GT/s di larghezza di banda

AMD 780G

AMD SB700

ITE 8718F

Fo rnis ce le funzion al ità legacy Sup er

I/O usate più comunemente.

Alloggi DIMM DDR2 x 4

Capacità massima della memoria 8GB

Ciascun DIMM supporta DDR2

256/512MB e 1GB/2GB

ALC662

Alloggio PCI Express Gen2 x16 x1

Alloggio PCI Express Gen2 x1 x1

Allo g gio PC I x2

Connettore floppy x1 Ciascun connettore supporta 2 unità Floppy

Connettore IDE x1 Ciascun connettore supporta 2 unità IDE

Connettore SATA x6 Ciascun connettore supporta 1 unità SATA

Co nnettor e p annello fron tale x 1 Sup po rt a i servizi de l panne llo fron tale

SPECIFICA

L’arch itet tura AMD 6 4 abilit a la co mput az io ne 32

e 64 bit

Supporto di Hyper Transport 3.0 e Cool’n’Quiet

Interfaccia LPC (Low Pin Count)

Funzioni di controllo dell’ambiente:

Monitoraggio hardware

Funzione "Smart Guardian" di ITE

Modulo di memoria DDR2 a canale doppio

Supporto di DDR2 533 / 667 / 800

Supporto di DDR2 1066 (for AM2+ CPU only)

DIMM registrati e DIMM ECC non sono supportati

La memoria video condivisa massima è di 512 MB

Supporto DX10

Supporto HDCP / UVD

Modalità Bus Master Ultra DMA 33 / 66 / 100 /

133

Supporto modalità PIO Mode 0-4

Velocità di trasferimento dei dati fino a 3 Gb/s.

Co mp at ibile specif iche SATA Version e 2 .0 .

Negoziazione automatica 10 / 100 /1000 Mb/s
Capacità Half / Full Duplex

Uscita audio 5.1 canali

Supporto audio High-Definition (HD)

40

I/O

pannello

posteriore

Dimension

i scheda

Caratterist

iche

speciali

Sistemi

oper at ivi

supportati

TA780G M2+

SPECIFICA

Connettore audio frontale x1 Supporta la funzione audio pannello frontale

Connettore CD-in x1 Supporta la funzione input audio CD

Connettore output SPDIF x1 Supporta la funzione d’output audio digitale

Co llet t ore ven tolina C PU x 1

Co llet t ore ven tolina s is t em a x1 Aliment az io ne vent olin a d i sistema

Co llet t ore can ce llaz io n e CMOS x 1

Connettore USB x3

Connettore alimentazione x1

(24 pin)

Connettore alimentazione x1

(4 pin)

Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante

Connettore Porta s eriale x1

Tas t iera P S / 2 x1

Mou s e PS /2 x 1

Porta VGA x1

Porta LA N x1

Porta USB x4

Connettore audio x3

Porta DV I x1

215 mm (larghezza) x 244 mm

(altez za)

Supporto RAID 0 / 1 / 1+0

Supporto HyperFlash

Windows XP / VISTA

Alimentazione ventolina CPU (con funzione Smart

Fan)

Ciascun connettore supporta 2 porte USB

pannello frontale

Biostar si riserva il diritto di aggiungere o

rimuovere il supporto di qualsiasi sistema

operativo senza preavviso.

41

Motherboard Manual

SPANISH

Conector AM2+ / AM2

CPU

FSB

Conjunto

de chips

Súper E/S

Memoria

principal

Gráficos

IDE Controlador IDE integrado

SATA Controlador ATA Serie Integrado

Red Local Realtek RTL 8111C

Soporte de

sonido HD

Ranuras

Conectores

en p laca

Procesadores AMD Athlon 64 / Athlon 64

FX / Athlon 64 X2 / Sempron / Pheno m

Admite HyperTransport 3.0 con un ancho

de banda de hasta 5.2 GT/s

AMD 780G

AMD SB700

ITE 8718F

Le ofrece las funcionalidades heredadas

de uso más común Súper E/S.

Ranuras DIMM DDR2 x 4

Capacidad máxima de memoria de 8GB

Cada DIMM admite DDR de 256/512MB y

1GB/2GB

Integrados en el conjunto de chips AMD

780G

ALC662

Ranura PCI Express Gen2 x16 X1

Ranura PCI Express Gen2 x1 X1

Ranura PCI X2

Conector disco flexible X1 Cada conector soporta 2 unidades de disco flexible

Conector IDE X1 Cada conector soporta 2 dispositivos IDE

Conector SATA X6 Cada conector soporta 1 dispositivos SATA

Especificación

La arquitectura AMD 64 permite el procesado de 32 y

64 bits

Soporta las tecnologías Hyper Transport 3.0 y

Cool’n’Quiet

Interfaz de cuenta Low Pin

In iciat iv as de cont rol d e ento rno ,

Monitor hardware

Función "Guardia inteligente" de ITE

Módulo de memoria DDR2 de canal Doble

Admite DDR2 de 533 / 667 / 800

Admite DDR2 de 1066 (for AM2+ CPU only)

No admite DIMM registrados o DIMM compatibles con

ECC

Memoria máxima de vídeo compartida de 512 MB

Admite DX10

Admite HDCP / UVD

Modo bus maestro Ultra DMA 33 / 66 / 100 / 133

Soporte los Modos PIO 0~4,

Tasas de transferencia de hasta 3 Gb/s.

Co mp at ible con la vers ión S ATA 2.0.

Negociación de 10 / 100 / 1000 Mb/s

Funciones Half / Full dúplex

Salida de sonido de 5.1 canales

Soporte de sonido Alta Definición

42

Panel

trasero de

E/S

Ta mañ o d e

la placa

Funciones

especiales

Soporte de

sistema

operativo

TA780G M2+

Especificación

Co nect o r de panel fro nta l X1 Soporta inst a la c iones en e l p ane l front al

Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal

Conector de entrada de CD X1 Soporta función de entrada de sonido de CD

Conector de salida S/PDIF X1 Soporta función de salida de sonido digital

Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con

función Smart Fan)

Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema

Cabecera de borrado de CMOS X1

Conector USB X3 Cada co nector soporta 2 puert os USB frontales

Conector de alimentación X1

(24 patillas)

Conector de alimentación X1

(4 patillas)

Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora

Conector Puerto serie X1

Tec lad o P S /2 X 1

Ratón PS/2 X1

Puerto VGA X1

Puerto de red local X1

Puert o USB X4

Conector de sonido X3

Puert o DV I X1

215 mm. (A) X 244 Mm. (H)

Admite RAID 0 / 1 / 1+0

Admite HyperFlash

Windows XP / VISTA

Biostar se reserva el derecho de añadir o retirar el

soporte de cualquier SO con o sin aviso previo.

43

Motherboard Manual

/2

PORTUGUESE

Socket AM2+ / AM2

CPU

FSB

Chipset

Especificaç

ão Super

I/O

Memória

principal

Placa

gráf ica

IDE Controlador IDE integrado

SATA Controlador Serial ATA integrado

LAN Realtek RTL 8111C

Suporte

para áudio

de alta

definição

Ranhuras

Conectores

na placa

Processadores AMD Athlon 64 / Athlon 64

FX / A lthlon 6 4 X2 / S emp ron / Pheno m

Suporta a tecnologia HyperTransport 3.0

com u ma largura de band a até 5. 2 GT/s

AMD 780G

AMD SB700

ITE 8718F

Proporciona as funcionalidades mais

utilizadas em termos da especificação

Super I/O.

Ranhuras DIMM DDR2 x 4

Capacidad e máx ima de me mória: 8 GB

Cada módulo DIMM suporta uma

memória DDR2 de 256/512 MB & 1 GB

GB

Integrada no chipset A MD 780G

ALC662

Ranhura PCI Express Gen2 x16 x1

Ranhura PCI Express Gen2 x1 x1

Ranhura PCI x2

Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de disquetes

Conector IDE x1 Cada conector suporta 2 dispositivos IDE

Conector SATA x6 Cada conector suporta 1 dispositivo SATA

Conector do painel frontal x1 Para suporte de várias funções no painel frontal

ESPECIFICAÇÕES

A arquitectura AMD 64 p ermite uma co mputaç ão d e

32 e 64 bits

Suporta as tecno log ias Hyper Transport 3.0 e

Cool’n’Quiet

Interface LPC (Low Pin Count).

In iciat iv as par a con tro lo d o amb ien te

Monitorização do hardware

Função "S mart Gu ard ian" d a ITE

Módulo de memória DDR2 de canal duplo

Suporta módulos DDR2 533 / 667 / 800

Suporta módulos DDR2 1066 (for AM2+ CPU only)

Os módulos DIMM registados e os DIMM ECC não são

suportados

Memória de vídeo máxima partilhada: 512 MB

Suporta as funções DX10

Suporta as funções HDCP / UVD

Modo Bus master U ltra DMA 33 / 66 / 100 / 133

Suporta o modo PIO 0~4,

Velocidades de transmissão de dados até 3 Gb/s.

Compat ibilidade com a es pe cificação SATA versão 2.0.

Auto negociação de 10 / 100 / 1000 Mb/s

Capacidade semi/full-duplex

Saída de áudio de 5.1 canais

Suporta a especificação High-Definition Audio

44

Entradas/S

aídas no

painel

traseiro

Tamanho

da placa

Característi

cas

especiais

Sistemas

operativos

suportados

TA780G M2+

ESPECIFICAÇÕES

Conector de áudio frontal x 1 Suporta a fun ção de áud io no painel frontal

Conector para entr ada de CDs x1 Supo rta a entrada de áudio a p art ir de CDs

Conector de saíd a S/ PD IF x1 Supo rta a sa ída de áud io digital

Conector da ventoinha da CPU x1

Conector da ventoinha do s istema x1 Alimentação da vento inha do sistema

Conector para limpeza do CMOS x1

Conector USB x3 Cada conector suporta 2 portas USB no painel frontal

Conector de alimentação x1

(24 pinos)

Conector de alimentação x1

(4 p inos )

Conector da para impressora x1 Cada conector suporta 1 Porta para impressora

Conector da Porta série x1

Tec lad o P S /2 x 1

Rato PS/2 x1

Porta VGA x1

Porta LA N x1

Porta USB x4

Tomada de áudio x3

Porta DV I x 1

215 mm (L) X 244 mm (A)

Suporta as funções RA ID 0 / 1 / 1+0

Suporta as funções Hyp erF las h

Windows XP / VISTA

Alimentação da ventoinha da CPU (com a função

Smart Fan)

A Biostar reserva-se o direito de adicionar ou remover

suporte para qualquer sistema operativo com ou sem

av iso prév io .

45

Motherboard Manual

POLISH

SPEC

Socket AM2+ / AM2

Procesor

FSB

Chipset

Pamięć

główna

Super I/O

Graf ika Zintegrowan a w chipse cie AMD 78 0G

IDE Zintegrowany kontroler IDE

SATA Zintegrowany kontroler Serial ATA

LAN Realtek RTL 8111C

Obsługa

aud io HD

Gniazda

Złącza

wbud owan

e Złącze S ATA x6 Każde złącze obs ługuje 1 urządzenie SATA

AMD Athlon 64 / Athlon 64 FX / A lthlon 64

X2 / Sempron / Phenom Procesory

Obsługa HyperTransport 3.0 o szerokości

pasma do 5.2 GT/s

AMD 780G

AMD SB700

Gniazda DDR2 DIMM x 4

Maks. wielkość pamięci 8GB

Każde gniazdo DIMM obs ługuje moduły

256/512MB oraz 1GB/2GB DDR2

ITE 8718F

Zapewnia najbardziej powszechne

funkcje Super I/O.

ALC662

Gniazdo PCI Express Gen2 x16 x1

Gniazdo PCI Express Gen2 x1 x1

Gniazdo PCI x2

Złącze napędu dyskietek x1 Każde złącze obs ługuje 2 napędy dyskietek

Złącze IDE x1 Każde złącze obsługuje 2 urządzenia IDE

Architektura AMD 64 umożliwia przetwarzanie 32 i 64

bitowe

Obsługa Hyper Transport 3.0 oraz Cool’n’Quiet

Mod uł pamięci DDR2 z trybem podwójnego kanału

Obsługa DDR2 533 / 667 / 800

Obsługa DDR2 1066 (for A M2+ CPU only)

Brak obsług i Regist ered D IMM oraz ECC DIMM

Interfejs Low Pin Count

Funkcje kontroli warunków pracy,

Mon itor H /W

Funkcja ITE "Smart Guard ian"

Maks. wielkość współdz ie lo n ej pami ęci video wynosi

512 MB

Obsługa DX10

Obsługa HDCP / UVD

Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master

obsługa PIO tryb 0~4,

Transfer danych do 3 Gb/s.

Zgodność ze specyfikacją SATA w wersji 2.0.

10 / 100 /1000 Mb/s z automatyczną negocjacją

szybkości

Działanie w trybie połowicznego / pełnego dupleksu

5.1 kanałowe wyjście audio

Obsługa H igh- Def inition Aud io

46

Back Panel

I/O

Wymiary

płyty

Funkcje

specjalne

Obsluga

systemu

operacyjne

go

TA780G M2+

SPEC

Złącze panela przedniego x1 Obsługa elementów panela przedniego

Przedn ie złącze audio x1 Obsługa funkcji audio na panelu przednim

Złącze wejścia CD x1 Obsługa funkcji wejścia audio CD

Złącze wyjścia S/PDIF x1 Obsługa funkcji cyfrowego wyjścia aud io

Złącze głó wkowe wentylatora procesora

x1

Złącze głó wkow e wentylato ra

systemowego x1

Złącze głó wkowe kasowania CMOS x1

Złącze USB x3

Złącze zasilania (24 pinowe) x1

Złącze zas ilania (4 p ino we) x1

Złącze Port drukarki x1 Każde złącze obs ługuje 1 Port drukarki

Złącze Port szeregowy x1

Klawiatura PS/2 x1

Mys z PS /2 x 1

Port VGA x1

Port LAN x1

Port USB x4

Gniazdo audio x3

Port DVI x 1

215 mm (S) X 244 mm (W)

Obsługa RAID 0 / 1 / 1 +0

Obsługa HyperFlash

Windows XP / VISTA

Zasilanie wentylatora procesora (z funkcją Smart Fan)

Zasilanie wentylatora systemowego

Każde złącze obs ługuje 2 porty USB na panelu

przednim

Biostar zastrzega sobie prawo dodawania lub

odwoływ ania obsług i dowo ln ego sys temu

operacyjnego b ez powiado mienia.

47

Motherboard Manual

RUSSIAN

CPU
(централь

ный

процессор

)

FSB

Набо р
микросхем

Основная
память

Super I/O

Графика

IDE

SATA

Локальна я
сеть
Звуко вая

поддержка
жестког о
диска

Слоты

Встроенны
й разъём

Гнездо AM2+ / AM2
Процессоры AMD Athlon 64 / Athlon 64

FX / A lthlon 6 4 X2 / S emp ron / Pheno m

Поддержка HyperTransport 3.0 с
пропускной способностью до 5.2 GT/s

AMD 780G
AMD SB700

Слоты DDR2 DIMM x 4
Максимальная ёмкость памяти 8 ГБ
Каждый модуль DIMM поддерживает

256/512МБ & 1ГБ/2ГБ DDR2

ITE 8718F

Обеспечивает наиболее используемые
действующие фун кц ио наль ны е
возможно сти Super I/O.

Встроенная в набор микросхем AMD

780G

Встроенное устройство управления
встроенными интерфейсами устройс тв
Встроенное последовател ьно е
устройс тво управления ATA

Realtek RTL 8111C

ALC662

Слот PCI Express Gen2 x16 x1
Слот PCI Express Gen2 x1 x1
Слот PCI x2

Разъ ём НГМД x1

Разъ ём IDE x1

СПЕЦ

Арх итектура AMD 64 разрешать обработка данных
на 32 и 64 бит
Поддержка Hyper Transport 3.0 и Cool’n’Quiet

Мод ул ь памяти с двухканальным режимом DDR2
Поддержка DDR2 533 / 667 / 800
Поддержка DDR2 1066 (for AM2+ CPU only)
Не поддерживает зарегистрированные модули

DIMM and ECC DIMM

Интерфейс с ни зким количес твом выводов
Инициативы по охране окружающей среды,
Аппаратный монитор
Функция ITE "Smart Gu ard ian " (Интеллектуальная
защит а)
Максимальная совместно используемая вид ео
память составляет 512 МБ
Поддержка DX10
Поддержка HDC P / UVD
Режим "хозяина" шины Ultra D MA 33 / 66 / 100 / 133
Поддержка режима PIO 0~4,
скорость передачи данных до 3 гигабит/с.
Соответствие спецификации SATA версия 2.0.
Автоматическо е согласование 10 / 100 / 1000 Мб /с
Частичная / полна я дуплексная способность

Звуко вая поддержка H igh- Def in ition

5.1канальный звуковой выход

Каждый разъём поддерживает 2 накопителя на
гибких магнитных дисках
Каждый разъём поддерживает 2 встроенных
интерфейса накопителей

48

Задняя
панель
средств
ввода-выв
ода

Разм ер
панели

Специальн
ые

техническ
ие

характери
стики

Поддержк
а OS

TA780G M2+

СПЕЦ

Разъ ём SATA x6 Каждый разъём поддерживает 1 устройство SATA
Разъ ём на лицевой панели x1 Поддержка устро йств на лицевой панели
Входной звуковой разъём x1 Поддержка звуко вых функций на лицевой панели
Разъ ём ввода для CD x1 Поддержка функции ввода для CD
Разъ ём вывод а для S/PDIF x1 Поддержка вывода цифровой звуковой фун кц и и
Контактирующее приспособление
вентил ятора центрального
процессора x1
Контактирующее приспособление
вентил ятора системы x1
Открытое контактирующее
приспособление CMOS x1

USB- разъём x3

Разъ ем питания (24 вы вод ) x1
Разъ ем питания (4 выво д) x1
Разъ ём Порт подключения
принтера x1
Разъ ём Последоват ельный порт x1
Клавиатура PS/2 x1
Мышь PS/2 x1
Пор т VGA x1
Пор т LAN x1
USB- порт x4
Гнездо для подключени я
наушников x3
Пор т DVI x1

215 мм (Ш) X 244 мм (В)

Поддержка RAID 0 / 1 / 1+0
Поддержка HyperF lash

Windows XP / VISTA

Источник пит ания для вентил ятора центрального
процессора (с функц ией интеллектуального
вентил ятора)

Источник пит ания для вентил ятора системы

Каждый разъём поддерживает 2 USB-порта на
лицевой панели

Каждый разъём поддерживает 1 По рт подключения
принтера

Biostar сохраняет за собой право добавлять или
удаля ть средства обеспечения для OS с или без
предварительного уведом ле ния .

49

Motherboard Manual

ARABIC

ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗAMD 64 ﻴﻠﻤﻌﻟا ءاﺮﺟإ ﺔﻋﺮﺴﺑ ﺔﻴﺑﻮ ﺳﺎﺤﻟ ا تﺎ32 و64 ﺖﺑ

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyper Transport و 3.0 Cool’n’Quiet

ﺗﻢﻋﺪ ﺔﻴﻨﻘ ﺗ Low Pin Count Interface

ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو:

ةﺰﻬﺟﻷا ﺔﻟﺎﺡ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻡ

ﺔﻔﻴﻇو"S mart Guardian" ﻦﻡ IT E

ةﺮآاذ ةﺪﺡوDDR2 ﻘﻟا ﺔﺟودﺰﻡةﺎﻨ

ﻢﻋﺪﺗ عﻮﻥ ﻦﻡ ةﺮآاﺬﻟا DDR2 تﺎﻌﺳ 533 / 667 / 800 ﺖیﺎﺑ ﺎﺠﻴﻡ

عﻮﻥ ﻦﻡ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR2 تﺎﻌﺳ 1066ﺖیﺎﺑ ﺎﺠﻴﻡ

(DDR2 1066 is for AM2+ CPU only)

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻDIMM ﻊﻡ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠ ﺗو ECC

ﻰﺼﻗأ ﺔﻌﺳ ةﺮآاﺬﻟ ﻮیﺪﻴﻔﻟا ﺔآﺮﺘ ﺸﻤﻟا 512 ﺎﺠﻴﻡ ﺖیﺎﺑ

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗDX10

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHDCP / UVD

ﺔﻴﻨﻘ ﺘﺑ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100 / 133ﻲﺴﻴﺋر ﻊﺿو

ﻊﺿو ﻢﻋدPIO Mode 0~4

ﻞﻘﻥ تﺎﻥﺎﻴﺒﻟا تﺎﻋﺮﺴﺑ ﻞﺼﺗ ﻰﻟإ 3 ﺖﺑﺎﺠﻴﺟ/ﺔﻴﻥﺎﺙ.

ﺔﻘﺑﺎﻄﻡ تﺎﻔﺹاﻮﻤﻟ SATA راﺪﺹﻹا 2.0.

ﻞﻡﺎﻜﻟا جودﺰﻤﻟا ﻞﻘﻨﻟا ﺔﻴﻥﺎﻜﻡإ/ﻲﻔﺼﻨﻟا

5.1 تاﻮﻨﻗ جﺮﺨﻟ تﻮﺼﻟا

ﻦﻡ ﻒیﺮﻌﺘﻟا ﻲﻟﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗ

ﺔﻥﺮﻤﻟا صاﺮﻗﻸﻟ ﻦﻴآﺮﺤﻡ ﻢﻋﺪی

ةﺰﻬﺟأ ﻦﻡ ﻦﻴﻨﺙا ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪیIDE

ةﺰﻬﺟأ ﻦﻡ ﺪﺡاو ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪیSATA

تﺎﻔﺻاﻮﻤﻟا

تﺎﺠﻟﺎﻌﻡAMD Athlon 64 / Athlon 64 FX / Sempron /

Phenom / Althlon 64 X2

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyperTransport ﻰﻟإ ﻞﺼی ددﺮﺘﺑ 3.0 5.2 GT/s

ﺔﻔﻴﻇ و ﺮﻓﻮﺗSuper I/O ًﺎ ﻡ ا ﺪ ﺨﺘﺳا ﺮﺜآﻷا .

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM ﺪﺗ عﻮﻥ ﻦﻡ ةﺮآاذ ﻢﻋ DDR2 ﺔﻌﺳ

ﻖﺋﺎﻗر ﻲﻓ ﺔﺠﻡﺪﻡ AMD 780G

ﻲﺋﺎﻘﻠﺗ ضو ﺎﻔﺗ10/100 / 1000 ﺖیﺎﺑ ﺎﺠﻴﻡ /ﺔﻴﻥﺎﺙ

ﺔﺤﺘﻓGen2 x16 PCI Express دﺪﻋ1

ﺔﺤﺘﻓGen2 x1 PCI Express دﺪﻋ1

ﺔﺤﺘﻓPCI دﺪﻋ2

ﺲﺒﻘﻡAM2+ / A M2

AMD 780G

AMD SB700

ITE 8718F

ﺔﺤﺘﻓDDR2 DIM M دﺪﻋ4

ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ8 ﺖیﺎﺑ ﺎﺠﻴﺟ

256/512 ﺎﺠﻴﻡ

و ﺖیﺎﺑ1/و 2 ﺎﺠﻴﺟﺖیﺎﺑ

ﻢﻜﺤﺘﻡIDE ﻞﻡﺎﻜﺘﻡ ﺬﻔﻨﻡ IDE

ﻢﻜﺤﺘﻡ Serial ATA ﻞﻡﺎﻜﺘﻡ

Realtek RTL 8111C

ALC662

ﺔﻥﺮﻡ صاﺮﻗأ كﺮﺤﻡ ﺬﻔﻨﻡ دﺪﻋ1

ﺬﻔﻨﻡIDE دﺪﻋ1

ﺬﻔﻨﻡSATA دﺪﻋ6

ةﺪﺡو ﺔﺠﻟﺎﻌﻤﻟا

ﺔیﺰآﺮﻤﻟا

ﻞﻗﺎﻨﻟا ﻲﻡﺎﻡﻷا ﻲﺒﻥﺎﺠﻟا

ﺔﻋﻮﻤﺠﻡ ﺢﺋاﺮﺸﻟا

Super I/O

ةﺮآاﺬﻟا ﺔﻴﺴﻴﺋﺮﻟا

ﺔﻗﺎﻄﺑ تﺎﻡﻮﺳﺮﻟا

SATA

ﺔﻜﺒﺵ ﺔﻴﻠﺥاد

ﻢﻋد تﻮﺼﻟا ﻲﻟﺎﻋ

ﻒیﺮﻌﺘﻟا

تﺎﺤﺘﻔﻟا

ﺬﻓﺎﻨﻤﻟا ﻰﻠﻋ ﺢﻄ ﺳ

ﺔﺡﻮﻠﻟا

50

ﺔﻴﻡﺎﻡﻷا ﺔﺡﻮﻠﻟا تاﺰﻴﻬﺠﺗ ﻢﻋﺪی

ﺔﻴﻡﺎﻡﻷا ﺔﺡﻮﻠﻟ ﺎﺑ تﻮﺼﻟا ﺔﻔﻴﻇ و ﻢﻋﺪی

ا صﺮﻘﻟا تﻮﺹ ﻞﺥد ﺔﻔﻴﻇ و ﻢﻋﺪیﺞﻡﺪﻤﻟ

ﻲﻤﻗﺮﻟا تﻮﺼﻟا جﺮﺥ ﺔﻔﻴﻇو ﻢﻋﺪی

ﺔﻔﻴﻇو ﻊﻡ ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺡو ﺔﺡوﺮﻤﻟ ﺔﻗﺎﻄ ﻟا ﻞﻴﺹﻮﺘﻟSmart Fan

مﺎﻈﻨﻟا ﺔﺡوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺘﻟ

ﺢﺴ ﻡ ﺔﻠﺹوCMOS دﺪﻋ1

آ ﻢﻋﺪی ﻲﺘﺤﺘﻓ ﺬﻔﻨﻡ ﻞ USBﺔﻴﻡﺎﻡﻷا ﺔﺡﻮﻠﻟﺎﺑ

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)24سﻮﺑد( دﺪﻋ1

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)4سﻮﺑد( دﺪﻋ1

ﺔﻌﺑﺎﻃ ﺬﻔﻨﻡ دﺪﻋ1

ﻲﻠﺴﻠﺴﺗ ﺬﻔ ﻨﻡ دﺪﻋ1

215 ﻢﻡ)ضﺮﻋ (X 244 ﻢﻡ)عﺎﻔﺗرا( ﻢﺠﺡ ﺔﺡﻮﻠﻟا

ﻆﻔﺘﺤﺗBiostar وأ رﺎﻄﺥﺈﺑ ﻞﻴﻐﺸﺗ مﺎﻈﻥ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿإ ﻲﻓ ﺎﻬﻘﺤﺑ

رﺎﻄﺥإ نوﺪﺑ.

تﺎﻔﺻاﻮﻤﻟا

TA780G M2+

ﺔﻴﻡﺎﻡﻷا ﺔﺡﻮ ﻠﻟا ﺬﻔﻨﻡ دﺪﻋ1

ﻲﻡﺎﻡﻷا تﻮﺼﻟا ﺬﻔﻨﻡ دﺪﻋ1

ﺬﻔﻨﻡCD-IN دﺪﻋ1

جﺮﺥ ﺬﻔﻨﻡS/PDIF دﺪﻋ1

ﺔیﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺡو ﺔﺡوﺮﻡ ﺔﻠﺹو دﺪﻋ1

مﺎﻈﻨﻟا ﺔﺡوﺮﻡ ﺔﻠﺹو دﺪﻋ1

ﺬﻔﻨﻡUS B دﺪﻋ3

ﺢﻴﺗﺎﻔﻡ ﺔﺡﻮﻟPS/2 دﺪﻋ1

سوﺎﻡ PS/2 دﺪﻋ1

ﺬﻔﻨﻡVGA دﺪﻋ1

ﺔﻴﻠﺤﻡ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻡ دﺪﻋ1

ﺬﻓﺎﻨﻡUSB دﺪﻋ4

تﻮﺹ ﺲﺒﻘﻡ ﺪﻋ3

ﺬﻓﺎﻨﻡDV I دﺪﻋ1

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗRAID 0 / 1 / 1+0

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyperFlash

Windows XP / VISTA

ﺬﻓﺎﻨﻡ ﻞﺥد/جﺮﺥ

ﺔﺡﻮﻠﻟا ﺔﻴﻔﻠﺨﻟا

ﺔﺹﺎﺥ ﺎیاﺰﻡ

ﻢﻋد ﺔﻤﻈﻥأ ﻞﻴﻐﺸﺘﻟا

51

Motherboard Manual

JAPANESE

Socket AM2+ / AM2

CPU

FSB

チップセット AMD 780G

メインメモ

リ

Super I/O

グラフィッ

クス

IDE 統合IDE コントローラ

SATA 統合シリアルATA コントローラ

LAN Realtek RTL 8111C

HDオーディ

オのサポート ALC662

AMD Athlon 64 / Athlon 64 FX / A lthlon 64

X2 / S empron / Ph enom プロセッサ

5.2 GT/sのバンド幅までハイパートランスポ

ート3.0をサポートします

AMD SB700

DDR2 DIMMスロット x 4

最大メモリ容量8GB

各DIMMは 25 6/512MB & 1GB/2GB DDR2

をサポート

ITE 8718F

もっとも一般に使用されるレガシーSuper I/O

機能を採用しています。

AMD 780Gチップセットに統合

仕様

AMD 64アーキテクチャでは、32ビットと64 ビット計算が可

能です

ハイパートランスポート3.0とクールアンドクワイアットを

サポートします

デュアル チャンネルモードDDR2メモリモジュール

DDR2 533 / 667 / 800 をサポート

DDR2 1066 をサポート (for AM2+ CPU only)

登録済みDIMMとECC DIMMはサポートされません

低ピンカウントインターフェイス

環境コントロールイニシアチブ、

H/Wモニター

ITE の「スマートガーディアン」機能

最大の共有ビデオメモリは512MBです

DX10 のサポート

HDCP / UVD のサポート

Ultra DMA 33 / 66 / 100 / 133バスマスタモード

PIO Mode 0~4のサポート、

最高3Gb/秒のデータ転送速度

SATAバージョン2.0仕様に準拠。

10 / 100 /1000 Mb/秒のオートネゴシエーション

半/全二重機能

5.1チャンネルオーディオアウト

ハイデフィニションオーディオのサポート

スロット

オンボード

コネクタ

52

PCI Express Gen2 x16スロット x1

PCI Express Gen2 x1スロット x1

PCIスロット x2

フロッピーコネクタ x1 各コネクタは2つのフロッピードライブをサポートします

IDE コネクタ x1 各コネクタは2つのIDE デバイスをサポートします

SATAコネクタ x6 各コネクタは1つのSATAデバイスをサポートします

フロントパネルコネクタ x1 フロントパネル機能をサポートします

フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします

CDインコネクタ x1 CDオーディオイン機能をサポートします

S/PDIFアウトコネクタ x1 デジタルオーディオアウト機能をサポートします

CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載)

システムファンヘッダ x1 システムファン電源装置

CMOSクリアヘッダ x1

USBコネクタ x3

電源コネクタ(24 ピン) x1

電源コネクタ(4ピン) x1

プリンタポートコネクタ x1 各コネクタは1つのプリンタポートをサポートします

シリアルポートコネクタ x1

PS/2キーボード x1

PS/2マウス x1

背面パネル

I/O

ボードサイ

ズ

特殊機能

OSサポート W indows XP / VISTA

VGAポート x1

LANポート x1

USBポート x4

オーディオジャック x3

DVIポート x1

215 mm (幅) X 244 mm (高さ)

RAID 0 / 1 / 1+0 のサポート

Hyp erF lash のサポート

TA780G M2+

仕様

各コネクタは2つのフロントパネルUSBポートをサポートし

ます

Biostarは事前のサポートなしにOSサポートを追加または削

除する権利を留保します。

2008/01/15

53