Page 1
TA770 A2+ Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Page 2
Table of Contents
Chapter 1: Introduction ............................................................ 1
1.1 Before You Start ................................................................................ 1
1.2 Package Checklist............................................................................. 1
1.3 Motherboard Features...................................................................... 2
1.4 Rear Panel Connectors (for Ver 5.x)............................................... 4
1.5 Rear Panel Connectors (for Ver 6.x)............................................... 4
1.6 Motherboard Layout......................................................................... 5
Chapter 2: Hardware Installation ............................................. 6
2.1 Installing Central Processing Unit (CPU)....................................... 6
2.2 FAN Headers...................................................................................... 8
2.3 Installing System Memory ................................................................ 9
2.4 Connectors and Slots....................................................................... 11
Chapter 3: Headers & Jumpers Setup ..................................... 13
3.1 How to Setup Jumpers .................................................................... 13
3.2 Detail Settings.................................................................................. 13
Chapter 4: RAID Functions ..................................................... 22
4.1 Operation System............................................................................ 22
4.2 Raid Arrays...................................................................................... 22
4.3 How RAID Works............................................................................. 22
Chapter 5: OverClock Quick Guide .......................................... 27
5.1 T-Power Introduction...................................................................... 27
5.2 T-Power BIOS Feature.................................................................... 28
5.3 T-Power Windows Feature ............................................................ 36
Chapter 6: Useful Help ............................................................ 41
6.1 Driver Installation Note.................................................................. 41
6.2 Award BIOS Beep Code.................................................................. 42
6.3 Extra Information............................................................................ 42
6.4 Troubleshooting............................................................................... 43
Appendencies: SPEC In Other Language ................................ 44
German.................................................................................................................. 44
France .................................................................................................................... 46
Italian ..................................................................................................................... 48
Spanish ................................................................................................................... 50
Portuguese ............................................................................................................ 52
Polish...................................................................................................................... 54
Russian ................................................................................................................... 56
Arabic..................................................................................................................... 58
Japane se ................................................................................................................ 60
Page 3
CHAPTER 1: INTRODUCTION
TA770 A2+
1.1 B
EFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
1.2 PACKAGE CHECKLIST
HDD Cable X 1
Serial ATA Cable X 2
Serial ATA Power Cable X 1
Rear I/O Panel for ATX Case X 1
User’s Manual X 1
Fully Setup Driver CD X 1
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
S/PDIF out Cable X 1 (optional)
Note : The package contents may differ by area or your motherboard version.
1
Page 4
Motherboard Manual
1.3 MOTHERBOARD FEATURES
Ver 5.x Ver 6.x
CPU
FSB
Chipset
Super I/O
Main
Memory
IDE
SATA II
2
Socket AM2 / AM2+
AMD Athlon 64 / Athlon 64 FX / Athlon 64 X2 /
Sempron / A M2+ processors
AMD 64 Architecture enables 32 and 64 b it
computing
Supports Hyper Transport 3.0 and Cool=n=Quiet
Support HyperTransport 3.0
Supports up to 5.2 GT/s Bandwidth
AMD 770
AMD SB600
ITE 8718F
Prov ides the most common ly us ed legac y Super
I/O functionality.
Low Pin Count Interface
En vironm ent C ont ro l init iati ves ,
H/W Mon ito r
Fan Sp eed Controller
ITE's "S mart Guard ian " funct ion
DIMM Slots x 4
Each DIMM supports 512/1024/2048MB DDR2
Max Memory Capicity 8GB
Dual Cha nnel Mode DDR 2 me mory modu le
Supports DDR2 533 / 667 / 800
Supports DDR2 1066 (by AM2+ CPU)
Register ed D IMM and ECC D IMM is not
supported
Int eg r at ed IDE Cont ro lle r
Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode
supports PIO Mode 0~4,
AMD SB600 (Onboard)
Jmicro JMB36 2 (eSATA) (opt iona l)
Data transfer rates up to 3 Gb/s.
SATA Vers ion 2.0 spe cificat ion comp liant .
RAID 0,1,1+0 support (Onboard)
NCQ/Port-Multiplier/RAID 0,1,5,0+1 support
(eSATA) (optional)
Socket AM2 / AM2+
AMD Athlon 64 / Athlon 64 FX / Athlon 64 X2 /
Sempron / A M2+ processors
AMD 64 Architecture enables 32 and 64 b it
computing
Supports Hyper Transport 3.0 and Cool=n=Quiet
Support HyperTransport 3.0
Supports up to 5.2 GT/s Bandwidth
AMD 770
AMD SB600
ITE 8718F
Prov ides t he most commonly used legacy Super
I/O functionality.
Low Pin Count Interface
En vironm ent C ont ro l init iati ves ,
H/W Mon ito r
Fan Sp eed Controller
ITE's "S mart Guard ian " funct ion
DIMM Slots x 4
Each DIMM supports 512/1024/2048MB DDR2
Max Memory Capicity 8GB
Dual Cha nnel Mode DDR 2 me mory modu le
Supports DDR2 533 / 667 / 800
Supports DDR2 1066 (by AM2+ CPU)
Register ed D IMM and ECC D IMM is not
supported
Int eg r at ed IDE Cont ro lle r
Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode
supports PIO Mode 0~4,
AMD SB600 (Onboard)
Jmicro JMB36 2 (eSATA) (opt iona l)
Data transfer rates up to 3 Gb/s.
SATA Vers ion 2.0 spe cificat ion comp liant .
RAID 0,1,1+0 support (Onboard)
NCQ/Port-Multiplier/RAID 0,1,5,0+1 support
(eSATA) (optional)
Page 5
TA770 A2+
Ver 5.x Ver 6.x
Marvell 88E8056 / 88E8039 (optional)
LAN
Sound
Slots
On Board
Connector
Back Panel
I/O
Board Size 244 mm (W) x 305 mm (L) 244 mm (W) x 305 mm (L)
OS Support
10 / 100 Mb/s / 1Gb/s auto negotiation (Gigabit
bandwidth is for Marvell 88E8056 only)
Half / Full duplex capability
ALC888
7.1 channels audio out
Supports HD Audio
PCI slot x3 PCI slot x3
PCI Express Gen2 x16 slot x1 PCI Express Gen2 x16 slot x1
PCI Express Gen2 x1 slot x2 PCI Express Gen2 x1 slot x2
Floppy connecto r x1 Floppy connector x1
Printer Po rt conne ctor x1 Printer Port connect or x1
IDE Conn ect or x1 ID E C onn ector x1
SATA Connector x4 SATA Connector x4
Front Panel Connector x1 Front Panel Connector x1
Front Audio Connector x1 Front Audio Connector x1
CD-in Connector x1 CD-in Connector x1
S/PDIF out connector x1 S/PDIF out connector x1
CPU Fan header x1 CPU Fan header x1
System Fan head er x2 System Fan h eader x2
CMOS clear header x1 CMOS clear h eader x1
USB connector x2 USB connector x2
Serial port Connector x1 Serial port Connector x1
Power Connector (24pin) x1 Power Conn ector (24pin) x1
Power Connector (8pin) x1 Power Connector (8pin) x1
Power Connector (4pin) x1 Power Connector (4pin) x1
PS/2 Keyboard x 1
PS/2 Mouse x1
LAN port x1
USB Port x6
Audio Jack x6
eSATA Port (o ptional) x2
Windows XP / VISTA
Biostar Reserves the right to add or remove
support for any OS With or without notice.
Marvell 88E8056 / 88E8039 (optional)
10 / 100 Mb/s / 1Gb/s auto negotiation (Gigabit
bandwidth is for Marvell 88E8056 only)
Half / Full duplex capability
ALC662
5.1channels audio out
Supports HD Audio
PS/2 Keyboard x 1
PS/2 Mouse x1
LAN port x1
USB Port x6
Audio Jack x3
eSATA Port (o ptional) x2
Windows XP / VISTA
Biostar Reserves the right to add or remove
support for any OS With or without notice.
3
Page 6
Motherboard Manual
1.4 REAR PANEL CONNECTORS (FOR VER 5.X)
PS/2
Mouse
PS/2
Keyboard
USBX2
eSATAX2
(Optional)
Center
Rear
Side
USBX2
Line In
Line Out
Mic In
USBX2
1.5 REAR PANEL CONNECTORS (FOR VER 6.X)
PS/2
Mouse
LAN
LAN
Line In/
Surround
PS/2
Keyboa r d
4
USB X2
eSATAX2
(Optional)
USBX2
Line Out
Mic In 1/
Bass/ Center
USBX2
Page 7
1.6 MOTHERBOARD LAYOUT
TA770 A2+
JKBMS1
JUSBV2
JUSB2
ESATA X1
(optional)
JUSB1
JUSBLAN1
AUD IO1
(Ver 5.x)
JAUDI O1
(Ver 6.x)
J USBV1
LAN
(Opt io nal)
eSATA
JATXPWR2
J KBV1
JATXPWR3
PCI_EX1_1
PCI_EX1_ 2
JSFAN2
PC I_E X16
AMD
770
JCFAN1
Socket A M2
AMD
SB600
FDD1
DIMMA1
DIMMB1
DIMMB2
DIMMA2
JATXPWR1
BAT1
JCMOS1
IDE1
Codec
JAUDIOF1
JCDIN1
Note: represents the 1■
JSPDIF_OUT1
JPRNT1
PCI1
PCI2
PCI3
JCOM1
st
pin.
JUSBV3
JUSB3
JUSB4
Super I/O
LED_D2
SATA4
SATA3 SATA2 S ATA1
BIOS
JPANE L1
RS TS W 1
PWRSW1
LED_D1
JSFAN1
5
Page 8
Motherboard Manual
CHAPTER 2: HARDWARE INSTALLATION
2.1 I
NSTALLING CENTRAL PROCESSING UNIT (CPU)
Step 1: Remove the socket protection cap.
Step 2: Pull the lever toward direction A from the socket and then raise the
lever up to a 90-degree angle.
Step 3: Look for the white triangle on socket, and the gold triangle on
CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.
6
Page 9
TA770 A2+
Step 4: Hold the CPU down firmly, and then close the lever toward direct
B to complete the installation.
Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU
FAN power cable to the JCFAN1. This completes the installation.
Note: Please update the BIOS to the latest version while using AM2+ CPUs. Due to the latest CPU
transition, you may encounter the situation that the new system failed to boot while using new
AM2+ CPUs. In this case, please install one standard AM2 CPU to boot your system, and
update the latest BIOS from our website for AM2+ CPUs support.
7
Page 10
Motherboard Manual
2.2 FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
JCFAN1: CPU Fan Header
14
JCFAN1
JSFAN1/JSFAN2: System Fan Headers
1
3
JSFAN2
Pin
1 Ground
2 +12V
3
FAN RPM r ate
sense
4 Smart Fan
Control (By Fan)
Pin Assignment
1 Ground
2 +12V
3
Assignment
FAN RPM
rate sense
JSFAN1
1
3
Note:
The JCFAN1、JSFAN1 and JSFAN2 support 4-pin and 3-pin head connector. When
connecting with wires onto connectors, please note that the red wire is the positive and
should be co nnected to pin#2, and the black wire is Ground and should be connected to
GND.
8
Page 11
TA770 A2+
2.3 INSTALLING SYSTEM MEMORY
A. DDR2 Modules
DIMMA1
DIMMB1
DIMMA 2
DIMMB 2
1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
9
Page 12
Motherboard Manual
B. Memory Capacity
DIMM Socket
Location
DIMMA1 512MB/1024MB/2048MB
DIMMB1 512MB/1024MB/2048MB
DIMMA2 512MB/1024MB/2048MB
DIMMB2 512MB/1024MB/2048MB
DDR2 Module
C. Dual Channel Memory installation
To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:
Install memory module of the same density in pairs, shown in the following
table.
Dual Channel Status
Enabled O O X X
Enabled X X O O
Enabled O O O O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or
x16)
DIMMA1
Total Memory Size
Max is 8GB.
DIMMB1 DIMMA2 DIMMB2
10
Page 13
TA770 A2+
2.4 CONNECTORS AND SLOTS
FDD1: Floppy Disk Connector
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.
34
33
1
2
IDE1: Hard Disk Connector
The motherboard has a 32-bit Enhanced IDE Controller that provides PIO Mode
0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.
The IDE connector can connect a master and a slave drive, so you can connect
up to two hard disk drives.
40
39
2
1
11
Page 14
Motherboard Manual
PCI_EX16: PCI-Express Gen2 x16 Slot
- PCI-Express 2.0 compliant.
- Maximum theoretical realized bandwidth of 8GB/s simultaneously per
direction, for an aggregate of 16GB/s totally.
PCI_EX1_1/PCI_EX1_2: PCI-Express Gen2 x1 Slots
- PCI-Express 2.0 compliant.
- Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total.
- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.
- 2X bandwidth over the PCI-Express 1.0 architecture.
PCI_EX1_ 1
PCI_EX16
PC I_ EX1 _ 2
PCI1~PCI3: Peripheral Component Interconnect Slots
This motherboard is equipped with 3 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
12
PCI1
PCI2
PCI3
Page 15
TA770 A2+
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1 H
OW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
Pin opened Pin closed Pin1-2 closed
3.2 DETAIL SETTINGS
JPANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.
_
D
L
R
E
W
P
+
916
1
+
+
K
P
S
H
f
f
O
/
n
O
-
8
-
T
S
R
E
D
L
Pin Assignment Function Pin Assignment Function
1 +5V 9 N/A
2 N/A 10 N/A
3 N/ A 11 N/ A N/A
4 Speaker
5 HDD LED (+) 13 Power LED (+)
6 HDD LED (-)
7 Ground 15 Power button
8 Reset control
Speaker
Connector
Hard drive
LED
Reset button
12 Power LED (+)
14 Power LED (-)
16 Ground
N/A
Power LED
Power-on button
13
Page 16
Motherboard Manual
JATXPWR1: AT X Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
12
1
Pin Assignment Pin Assignment
24
13
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Gro und 3 Gro und
16 PS_ON 4 +5V
17 Gro und 5 Gro und
18 Ground 6 +5V
19 Gro und 7 Gro und
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V
JATXPWR2: AT X Power Source Connector
By connecting this connector, it will provide +12V to CPU power circuit.
8
5
Pin
4
1
Assignment
1 +12V
2 +12V
3 +12V
4 +12V
5 Ground
6 Ground
7 Ground
8 Ground
14
Page 17
TA770 A2+
JUSB3/JUSB4: Headers for USB 2.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
Assignment
Pin
1 +5V (fused)
2 +5V (fused)
3 USB4 USB5 USB+
6 USB+
7 Ground
USB3 USB4
2
10
9
1
JAUDIOF1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.
2
10
8 Ground
9 Key
10 NC
Pin Assignment
1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in
10 Jack Sense
1
9
15
Page 18
Motherboard Manual
JCDIN1: CD-ROM Audio-in Connector
This connector allows user to connect the audio source from the variaty devices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.
JCMOS1: Clear CMOS Header
By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.
Assignment
Pin
1 Left Channel Input
2 Ground
3 Ground
4 Right Channel Input
14
13
Pin 1-2 Close:
Normal Operation (default).
16
13
13
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for five seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Reset your desired password or clear the CMOS data.
Page 19
JPRNT1: Printer Port Connector
This header allows you to connector printer on the PC.
2
TA770 A2+
1
25
Pin Assignment Pin Assignment
1 -Strobe 14 Ground
2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7
5 Data 1 18 Ground
6 -Init 19 -ACK
7 Data 2 20 Ground
8 -Scltin 21 Busy
9 Data 3 22 Ground
10 Ground 23 PE
11 Data 4 24 Ground
12 Ground 25 SCLT
13 Data 5 26 Key
17
Page 20
Motherboard Manual
SATA1~SATA4: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 4 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.
SATA4 SATA3 SATA2 SATA1
Assignment
Pin
1 Ground
2 TX+
3 TX4 Ground
1
4
5 RX6 RX+
7 Ground
7
On-Board LED Indicators
There are 2 LED indicators on the motherboard to show system status.
LED_ D1
LED_ D2
LED_D1 and LED_D2:
These 2 LED indicate system power on diagnostics.
Please refer to the table below for different messages:
LED_D2 LED_D1 Message
OFF OFF Abnormal: CPU / Chipset error.
OFF ON Memory Error
ON OFF VGA Error
ON ON Norma l
18
Page 21
On-Board Buttons
There are 2 on-board buttons.
TA770 A2+
PWRSW1RSTSW1
PWRSW1:
This is an on-board Power Switch button.
RSTSW1:
This is an on-board Reset button.
JSPDIF_OUT1: Digital Audio-out Connector
This connector allows user to connect the PCI bracket SPDIF output header.
13
Pin
Assignment
1 +5V
2 SPDIF_OUT
3 Ground
19
Page 22
Motherboard Manual
JATXPWR3: Auxiliary Power for Graphics
This connector is an auxiliary power connection for graphics cards. Exclusive
power for the graphics card provides better graphics performance.
JCOM1: Serial port Connector
The motherboard has a Serial Port Connector for connecting RS-232 Port.
Pin
Assignment
1 +12V
2 Ground
1
4
2
10
3 Ground
4 VCC
Pin Assignment
1 Carrier detect
2 Received data
3 Transmitted data
4
Data terminal ready
5 Signal ground
6 Data set ready
7 Request to send
8 Clear to send
9 Ring indicator
10 Key
20
1
9
Page 23
TA770 A2+
JKBV1: Power Source Header for PS/2 Keyboard and Mouse
3
13
JUSBV1/JUSBV2/JUSBV3: Power Source Headers for USB Ports
Pin 1-2 Close:
JUSBV1: +5V for USB ports at JUSB1/JUSBLAN1.
JUSBV2: +5V for USB ports at JUSB2.
JUSBV3: +5V for USB ports at front panel (JUSB3/JUSB4).
Pin 2-3 Close:
JUSBV1: +5V STB for USB ports at JUSB1/JUSBLAN1.
JUSBV2: +5V STB for USB ports at JUSB2.
JUSBV3: +5V STB for USB ports at front panel (JUSB3/JUSB4).
3
1
JUSBV2
JUSBV1
1
Pin 1-2 Close
+5V for PS/2 keyboard and
mouse.
Pin 2-3 close
+5V STB for PS/2 keyboard and
mouse.
31
Pin 1-2 close
3
1
JUSBV3
13
3
1
Pin 2-3 close
21
Page 24
Motherboard Manual
CHAPTER 4: RAID FUNCTIONS
4.1 O
Supports Windows XP Home/Professional Edition and Windows VISTA.
PERATION SYSTEM
4.2 RAID ARRAYS
RAID supports the following types of RAID arrays:
RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for
many applications.
RAID 1: RAID 1 defines techniques for mirroring data.
RAID 1+0 (Onboard): R AID 1+0 combines the techniques used in RAID 0 and RAID 1.
RAID 0+1 (eSATA) (Optional): RAID 0+1 combines the techniques used in RAID 0 and
RAID 1.
RAID 5 (eSATA) (Optional): RAID 5 provides fault tolerance and better utilization of disk
capacity.
4.3 HOW RAID WORKS
RAID 0:
The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks
up a lar ge f ile into smal ler blocks and perfo rm s d isk reads and writes ac ro ss multiple
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment. This
technique reduces overall disk access time and offers high bandwidth.
Features and Benefits
Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the
platform.
Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.
Benefits: provides increased data throughput, especially for large files. No
capacity loss penalty for parity.
Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.
Fault Tolerance: No.
22
Block 1
Blo ck 3
Blo ck 5
Block 2
Blo ck 4
Blo ck 6
Page 25
TA770 A2+
RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on a
second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the
active volume or drive is corrupted or becomes unavailable because of a hardware failure.
RAID techniques can be applied for high-availability solutions, or as a form of automatic
backup that eliminates tedious manual backups to more expensive and less reliab le
media.
Features and Benefits
Drives: Minimum 2, and maximum is 2.
Uses: RAID 1 is ideal for small databases or any other application that
requires fault tolerance and minimal capacity.
Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.
Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.
Fault Tolerance: Yes.
Block 1
Block 2
Block 3
Block 1
Block 2
Block 3
23
Page 26
Motherboard Manual
RAID 1+0 (For Onboard SATA Only):
RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 1+0
solution for improved resiliency, performance and rebuild performance.
Features and Benefits
Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
Benefits: Optimizes for both fault tolerance and performance, allowing for
automatic redundancy. May be simultaneously used with other RAID levels
in an array, and allows for spare disks.
Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.
Fault Tolerance: Yes.
24
Block 1
Block 3
Block 5
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
Block 2
Block 4
Block 6
Page 27
TA770 A2+
RAID 0+1 (For eSATA with Multiplier Only)(Optional):
RAID 0 drives can be mirrored using RAID 1 techniques. Resulting in a RAID 0+1
solution for improved performance plus resiliency.
Features and Benefits
Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
Benefits: Optimizes for both fault tolerance and performance, allowing for
automatic redundancy. May be simultaneously used with other RAID levels
in an array, and allows for spare disks.
Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.
Fault Tolerance: Yes.
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
25
Page 28
Motherboard Manual
RAID 5 (For eSATA with Multiplier Only)(Optional):
RAID 5 stripes both data and parity information across three or more drives. It writes
data and parity blocks across all the drives in the array. Fault tolerance is maintained by
ensuring that the parity information for any given block of data is placed on a different
drive from those used to store the data itself.
Features and Benefits
Drives: Mini mu m 3 .
Uses: RAID 5 is recommended for transaction processing and general
purpose service.
Benefits: An ideal combination of good performance, good fault tolerance,
and high capacity and storage efficiency.
Drawbacks: Individual block data transfer rate same as a single disk. Write
performance can be CPU intensive.
Fault Tolerance: Ye s.
Di sk 1
DATA 1
DATA 3
PARITY
DATA 7
DATA 9
PARITY
26
Di sk 2
DATA 2
PARITY
DATA 5
DATA 8
PARITY
DATA 11
Di sk 3
PARITY
DATA 4
DATA 6
PARITY
DATA 10
DATA 12
Page 29
CHAPTER 5: OVERCLOCK QUICK GUIDE
p
TA770 A2+
5.1 T-P
Biostar T-Power is a whole new utility that is designed for overclock users.
Based on many precise tests, Biostar Engineering Team (BET) has
developed this ultimate overclock engine to raise system performance.
No matter whether under BIOS or Windows interface, T-Power is able to
present the best system state according to users’ overclock setting.
T-Power BIOS Features:
T-Power Windows Feature:
OWER INTRODUCTION
Overclocking Navigator Engine (O.N.E.)
CMOS Reloading Program (C.R.P.)
Memory Integration Test (M.I.T., under Overclock Navigator Engine)
Integrated Flash Program (I.F.P.)
Self Recovery System (S.R.S)
Smart Fan Function (under PC Health Status)
Hardware Monitor
Overclock Engine
System Information
!! WARNING !!
For better system performance, the BIOS firmware is being
continuously updated. The BIOS information described below in
this manual is for your reference only and the actual BIOS
information and settings on board may be different from this
manual. For further information of setting up the BIOS, please
refer to the BIOS Manual in the Setup CD.
NOTE
Overclock is an optional process, but not a “must-do” process; it is
not recommended for inexperienced users. Therefore, we will not
be responsible for any hardware damage which may be caused by
overclocking. We also would not guarantee any overclocking
erformance.
27
Page 30
Motherboard Manual
5.2 T-POWER BIOS FEATURE
A. Overclocking Navigator Engine (O.N.E.):
ONE provides two powerful overclocking engines: MOS and AOS for both
Elite and Casual overclockers.
Manual Overclock System (M.O.S.)
MOS is designed for experienced overclock users.
It allows users to customize personal overclock settings.
28
Page 31
TA770 A2+
CPU Voltage :
This function will increase CPU stability when overclocking. However, the
CPU temperature will increase when CPU voltage is increased.
Memory Voltage :
This function will increase memory stability when overclocking.
HT Voltage Regulator:
This function will increase CPU stability when overclocking the HT ratio.
NB/SB Voltage Regulator:
This function will increase Northbridge and Southbridge chipset stability
when overclocking.
DRAM Configuration:
Enter this function for more advanced DRAM settings.
HT Link Control:
Enter this function for more advanced HT settings.
CPU Clock:
CPU Frequency is directly in proportion to system performance. To
maintain the system stability, CPU voltage needs to be increased also
when raising CPU frequency.
NPT Fid Contro l:
This function allows you to adjust the frequency ratio of CPU.
NPT Vid Control:
This function allows you to adjust the voltage of CPU.
Memory Clock Value:
This function allows you to set the memory clock.
29
Page 32
Motherboard Manual
Automatic Overclock System (A.O.S.)
For beginners in overclock field, BET had developed an easy, fast, and
powerful feature to increase the system performance, named A.O.S.
Based on many tests and experiments, A.O.S. provides 3 ideal overclock
configurations that are able to raise the system performance in a single
step.
V6 Tech Engine:
This engine will make a good over-clock performance.
30
V8 Tech Engine:
This engine will make a better over-clock performance.
Page 33
TA770 A2+
V12 Tech Engine:
This engine will make a best over-clock performance.
Notices:
1. Not all types of AMD CPU perform above overclock setting ideally; the difference will be based
on the selected CPU model.
B. CMOS Reloading Program (C.R.P.):
It allows users to save different CMOS settings into BIOS-ROM.
Users are able to reload any saved CMOS setting for customizing system
configurations.
Moreover, users are able to save an ideal overclock setting during overclock
operation.
There are 50 sets of record addresses in total, and users are able to name the
CMOS data according to personal preference.
31
Page 34
Motherboard Manual
C. Memory Integration Test (M.I.T.):
This function is under “Overclocking Navigator Engine” item.
MIT allows users to test memory compatibilities, and no extra devices or
software are needed.
Step 1:
The default setting under this item is “Disabled”; the condition parameter should
be changed to “Enable” to proceed this test.
↓
32
Step 2:
Save and Exit from CMOS setup and reboot the system to activate this test.
Run this test for 5 minutes (minimum) to ensure the memory stability.
Step 3:
When the process is done, change the setting back from “Enable” to “Disable”
to complete the test.
Page 35
TA770 A2+
D. Self Recovery System (S.R.S.):
This function can’t be seen under T-Power BIOS setup; and is always on
whenever the system starts up.
However, it can prevent system hang-up due to inappropriate overclock
actions.
When the system hangs up, S.R.S. will automatically log in the default BIOS
setting, and all overclock settings will be re-configured.
E. Integrated Flash Program (I.F.P.):
IFP is a safe and quick way to upgrade BIOS.
Step 1:
Go to Biostar website (http://www.biostar.com.tw
file. Then, save the file into a floppy disk.
Step 2:
Insert the floppy disk and reboot the system to get into CMOS screen.
Step 3:
Select the item “Integrated Flash Program” to get the following frame and
choose the BIOS file downloaded in step 1.
) to download the latest BIOS
Step 4:
Press “Enter” key to start BIOS file loading, and BIOS updating will process
automatically.
Step 5:
When the BIOS update is completed, press YES to the message “Flash done,
Reset system”, and the system will reboot automatically to finish the process.
Advise:
You can update the system BIOS by simply pressing “Enter” key for three times.
33
Page 36
Motherboard Manual
F. Smart Fan Function:
Smart Fan Function is under “Smart Fan Option” in “PC Health Status”.
This is a brilliant feature to control CPU/System Temperature vs. Fan speed.
When enabling Smart Fan function, Fan speed is controlled automatically by
CPU/System temperature.
This function will protect CPU/System from overheat problem and maintain the
system temperature at a safe level.
↓
34
Smart Fan Calibration
Choose this item and then the BIOS will automatically test and detect the
CPU/System fan functions and show CPU/System fan speed.
PWM Duty Off <℃>:
If the CPU/System temperature is lower than the set value, the CPU/
System fan will turn off. The range is from 0~127, with an interval of 1.
Page 37
TA770 A2+
PWM Duty Start <℃>
The CPU/System fan starts to work when CPU/System temperature
arrives to this set value. The range is from 0~127, with an interval of 1.
Start PWM Value
When CPU/System temperature arrives to the set value, the CPU/System
fan will work under Smart Fan Function mode. The range is from 0~127,
with an interval of 1.
Smart Fan Slope
Increasing the value of slope PWM will raise the speed of CPU/System fan.
The range is from 1~127, with an interval of 1.
35
Page 38
Motherboard Manual
5.3 T-POWER WINDOWS FEATURE
1. Desktop Icon
After the T-Utility has been installed, a T-Utility ico n will appear on the
desktop, just like the icon shown below.
Now you can launch the T-Utility simply by double-clicking the desktop
icon.
2. Main Panel
If you double-click the desktop icon, T-Utility will be launched. Please
refer to the following fig ure; the utility’s first window you will see is
Main Panel.
Main Panel contains features as follows:
a. Display the CPU Speed, CPU external clock, Memory clock, VGA
clock, and PCI clock information.
b. Contains About, Overclock/Overvoltage, and Hardware Monitor
Buttons for invoking respective panels. The On/Off button is for
closing the program.
36
Page 39
TA770 A2+
3. Overclock/Overvoltage Panel
Click the Overclock/Overvoltage button in the Main Panel, the button
will be highlighted and the Overc lock/Overvoltage Pa nel will show
up as the following figure. As you can see, the Overclock Panel is
on the upper side, and the Overvoltage Panel is on the lower side.
37
Page 40
Motherboard Manual
Overclock Panel contains these features:
a. “Auto-Overclock”:
User can click t his button and T-Utility will set the best and stable
performance and frequency automatically. A warning dialog as
below will show up to notify you that the system may become
unstable, click on “OK” to continue.
Then T-Utility will execute a series of testing until system fail.
Then system will do fail-safe reboot by using Watchdog function.
After reboot, launch the T-Utility again and the utility will load the
previously verified best and stable frequency.
38
b. “Verify”:
If you use the “Manual Adjust” bar to adjust the CPU frequency,
then you can click this button and T-Utility will proceed a testing for
current frequency. If the testing is ok, then the current frequency
will be saved into system registry. If the testing fails, system will do
a fail-safe rebooting. After reboot, the T-Utility will restore to the
hardware default setting.
Warning:
Manually overclock is potentially dangerous, especially when the
overclocking percentage is over 110 %. We strongly recommend you
verify every speed you overclock by click the Verify button. Or, you can
just click Auto overclock button and let T-Utility automatically gets the
best result for you.
c. “V3 Engine”/“V6 Engine”/“V9 Engine”:
Provide user the ability to do real-time overclock adjustment.
d. “Recovery”:
Click t his button and the T-Utility will restore all values to the
hardware default setting.
Page 41
TA770 A2+
e. “Save / Open Setting”:
Click Save button to save current setting to a file, and click Open
button to load a previously saved setting.
f. “Panel Color”:
Click this button to change the color of the panel.
Overvoltage Panel contains these features:
a. “CPU Voltage”:
This function allows user to adjust CPU voltage. Click on “+” to
increase or “-“ to decrease the CPU voltage.
b. “Memory Voltage”:
This function allows user to adjust Memory voltage. Click on “+”
to increase or “-“ to decrease the Memory voltage.
c. “Chipset Voltage”:
This function allows user to adjust Chipset voltage. Click on “+”
to increase or “-“ to decrease the Chipset voltage.
4. Hardware Monitor Panel
Click the Hardware Monitor button in Main Panel, the button will be
highlighted and the Hardware Monitor panel will s how up as the
following figure.
In this panel, you can get the real-time status information of your
system. The information will be refreshed every 1 second.
39
Page 42
Motherboard Manual
5. About Panel
Click the “about” button in Main Panel, the button will be highlighted
and the About Panel will show up as the following fig ure.
In this panel, you can get model name and detail information in hints
of all the chipset that are related to overclocking. You can also get
the the versio n number of T-Utility.
40
Note:
Because the overclock, overvoltage, and hardware monitor features
are controlled by several separate chipset, T-Utility divides these
features to separate panels. If one chipset is not on board, the
correlative button in Main panel will be disab led, but it will not
interfere with other panels’ functions. This property can make
T-Utility more robust.
Page 43
CHAPTER 6: USEFUL HELP
TA770 A2+
6.1 D
RIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader so ftware from
http://www.adobe.com/products/acrobat/readstep2.html
41
Page 44
Motherboard Manual
6.2 AWARD BIOS BEEP CODE
Beep Sound Meaning
One long beep followed by two short
beeps
High-low siren sound CPU overheated
One Short beep when system boot-up No error found during POST
Long beeps every other second No DRAM detected or install
Video card not found or video card
memory bad
System will shut down automatically
6.3 EXTRA INFORMATION
CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
42
Page 45
6.4 TROUBLESHOOTING
Probable Solution
1. No power to the system at all
Power light don’t illuminate, fan
inside power supply does not turn
on.
2. Indicator light on keyboard does
not turn on.
System inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drive is spinning.
System does not boot from hard disk
drive, can be booted from optical drive.
System only boots from optical drive.
Hard disk can be read and applications
can be used but booting from hard disk
is impossible.
Screen message says “Invalid
Configuration” or “CMOS Failure.”
Cannot boot system after installing
second hard drive.
TA770 A2+
1. Make sure power cable is
securely plugged in.
2. Replace cable.
3. Contact technical support.
Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.
1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
1. Back up data and applications
files.
2. Reformat the hard drive.
Re-install applications and data
using backup disks.
Review system’s equipment. Make sure
correct information is in setup.
1. Set master/slave jumpers
correctly.
2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
43
Page 46
Motherboard Manual
APPENDENCIES: SPEC IN OTHER LANGUAGE
G
ERMAN
Ver 5.x Ver 6.x
CPU
FSB
Chipsatz
Super E/A
Arbeitsspeich
er
IDE
SATA II
44
Sockel AM2 / AM2+
AMD Athlon 64 / Athlon 64 FX / Athlon 64 X2 /
Sempron / AM2+ Prozessoren
Die AMD 64-Architektur unt erstüt zt eine 32-Bitund 64-Bit-Datenverarbeitung
Unterstützt Hyper Transport 3.0 und
Cool’n’Quiet
Unterstützt HyperTransport 3.0 mit einer
Bandbreite von bis zu 5.2 GT/s
AMD 770
AMD SB600
ITE 8718F
Biet et die häufig ver wend eten alten Super
E/A-Funktionen.
Low Pin Count-Schnittstelle
Umgebungskontrolle,
Hardware-Überwachung
Lüfterdrehza hl-Controller
"Smart Guardian"-Funktion von ITE
DDR2 DIMM-Steckplätze x 4
Jeder DIMM unterstützt 512/1024/2048MB
DDR2.
Max. 8GB Arbeitsspeicher
Dual-Kanal DDR2 Speichermodul
Unterstützt DDR2 533 / 667 / 800
Unterstützt DDR2 1066 (by AM2+ CPU)
registrierte DIMMs. ECC DIMMs werden nicht
unterstützt.
Int eg r iert er IDE- Con tro lle r
Ultra DMA 33 / 66 / 100 / 133 Bus
Master-Modus
Unterstützt PIO-Modus 0~4,
AMD SB600 (Onboard)
Jmicro JMB36 2 (eSATA) (opt iona l)
Datentransferrate b is zu 3Gb/s
Konform mit d er SATA-Spezifikation Version 2.0.
Unterstützt RAID 0,1,1+0 (Onboard)
Unterstützt NCQ/Port-Multiplier/RAID 0,1,5,0+1
(eSATA) (optional)
Sockel AM2 / AM2+
AMD Athlon 64 / Athlon 64 FX / Athlon 64 X2 /
Sempron / AM2+ Prozessoren
Die AMD 64-Architektur unt erstüt zt eine 32-Bitund 64-Bit-Datenverarbeitung
Unterstützt Hyper Transport 3.0 und
Cool’n’Quiet
Unterstützt HyperTransport 3.0 mit einer
Bandbreite von bis zu 5.2 GT/s
AMD 770
AMD SB600
ITE 8718F
Biet et die häufig ver wend eten alten Super
E/A-Funktionen.
Low Pin Count-Schnittstelle
Umgebungskontrolle,
Hardware-Überwachung
Lüfterdrehza hl-Controller
"Smart Guardian"-Funktion von ITE
DDR2 DIMM-Steckplätze x 4
Jeder DIMM unterstützt 512/1024/2048MB
DDR2.
Max. 8GB Arbeitsspeicher
Dual-Kanal DDR2 Speichermodul
Unterstützt DDR2 533 / 667 / 800
Unterstützt DDR2 1066 (by AM2+ CPU)
registrierte DIMMs. ECC DIMMs werden nicht
unterstützt.
Int eg r iert er IDE- Con tro lle r
Ultra DMA 33 / 66 / 100 / 133 Bus
Master-Modus
Unterstützt PIO-Modus 0~4,
AMD SB600 (Onboard)
Jmicro JMB36 2 (eSATA) (opt iona l)
Datentransferrate b is zu 3Gb/s
Konform mit d er SATA-Spezifikation Version 2.0.
Unterstützt RAID 0,1,1+0 (Onboard)
Unterstützt NCQ/Port-Multiplier/RAID 0,1,5,0+1
(eSATA) (optional)
Page 47
TA770 A2+
Ver 5.x Ver 6.x
Marvell 88E8056 / 88E8039 (optional)
LAN
Audio-Codec
Steckplätze
Onboard-Ans
chluss
Rückseiten-E
/A
Platinengröße 244 mm (B) X 305 mm (L) 244 mm (B) X 305 mm (L)
OS-Unterstüt
zung
10 / 100 / 1000 Mb/s Auto-Negotiation
(Gigabit-Bandbreite nur beim Marvell 88E8056)
Halb-/ Vollduplex-Funktion
ALC888
7.1-Kanal-Audioausgabe
Unterstützt High-Definition Audio
PCI Stec kp latz x3 PCI Stec kp latz x3
PCI Express Gen2 x16 Steckplatz x1 PCI Express Gen2 x16 Steckplatz x1
PCI Express Gen2 x1 Steckplatz x2 PCI Express Gen2 x1 Steckplatz x2
Diskettenlaufwerkanschluss x1 Diskettenlaufwerkanschluss x1
Druckeranschluss Anschluss x1 Druckeranschluss Anschluss x1
IDE-Anschluss x1 IDE-Anschluss x1
SATA-Anschluss x4 SATA-Anschluss x4
Fronttafelanschluss x1 Fronttafelanschluss x1
Front-Audioanschluss x1 Front-Audioanschluss x1
CD-IN-Anschluss x1 CD-IN-Anschluss x1
S/PDIF- Ausgangsanschluss x1 S/PDIF- Ausgangsanschluss x1
CPU-Lüfter-Sockel x1 CPU-Lüfter-Sockel x1
System-Lüfter-Sockel x2 System-Lüfter-Sockel x2
"CMOS lös chen "-Sockel x1 "CMOS löschen"-Socke l x 1
USB-Anschluss x2 USB-Anschluss x2
Serieller Anschluss x1 Serieller Anschluss x1
Stromanschluss (24-polig) x1 Stromanschluss (24-polig) x1
St romans ch luss (8- polig ) x1 S tro mansch lus s (8-po lig ) x1
St romans ch luss (4- polig ) x1 S tro mansch lus s (4-po lig ) x1
PS/2-Tastatur x1
PS/2-Maus x1
LAN-Anschluss x1
USB-Anschluss x6
Audioanschluss x6
eSATA Anschluss(optional) x2
Windows XP / VISTA
Biostar behält sich das Recht vor, ohne
Ankündigung die Unterstützung für ein
Betriebssystem hinzuzufügen oder zu
entfernen.
Marvell 88E8056 / 88E8039 (optional)
10 / 100 / 1000 Mb/s Auto-Negotiation
(Gigabit-Bandbreite nur beim Marvell 88E8056)
Halb-/ Vollduplex-Funktion
ALC662
5.1-Kanal-Audioausgabe
Unterstützt High-Definition Audio
PS/2-Tastatur x1
PS/2-Maus x1
LAN-Anschluss x1
USB-Anschluss x6
Audioanschluss x3
eSATA Anschluss(optional) x2
Windows XP / VISTA
Biostar behält sich das Recht vor, ohne
Ankündigung die Unterstützung für ein
Betriebssystem hinzuzufügen oder zu
entfernen.
45
Page 48
Motherboard Manual
j
j
FRANCE
Ver 5.x Ver 6.x
UC
Bus frontal
Chipset
Super E/S
Mémoire
principale
IDE
SATA II
Socket AM2 / AM2+
Processeurs AMD Athlon 64 / Athlon 64 FX /
Athlon 64 X2 / Sempron / AM2+
L'architecture AMD 64 permet le calcul 32 et 64
bits
Prend en charge Hyp er Transport 3.0 et
Cool’n’Quiet
Prend en ch arge Hype r Transp ort 3.0
bande passante de 5.2 GT/s
AMD 770
AMD SB600
ITE 8718F
Fournit la fonctionnalité de Super E/S
patrimoniales la plus utilisée.
Int e rface à f aible co mp te de b ro ch es
Initiatives de contrôle environnementales,
Mon iteur d e mat ériel
Contrôleur de vitesse de ventilateur
Fonction "Gardien intelligent" de l'ITE
Fentes DDR2 DIMM x 4
Chaque DIMM prend en charge des DDR2 de
512/1024/2048 Mo
Capac ité mémo ire max i male de 8 Go
Module de mémoire DDR2 à mode à double voie
Prend en charge la DDR2 533 / 667 / 800
Prend en charge la DDR2 1066 (by AM2+ CPU)
Les DIMM à registres et DIMM avec code
correcteurs d'err eurs ne sont pas prises en
charg e
Contrôleur IDE intégré
Mode principale de Bus Ultra DMA 33 / 66 / 100 /
133
Prend en charge le mode PIO 0~4,
AMD SB600 (
Jmicro JMB36 2 (eSATA)
Taux de transfert jusqu'à 3 Go/s.
Co nforme à la sp éc if icat ion SATA Vers ion 2 .0
Prise en charge RAID 0,1,1+0 (embarqué)
Prise en charge NCQ/Port-Miltiplier/ RAID
0,1,5,0+1 (eSATA)
embarqué
(opt ion al)
)
(option al)
usqu'à une
Socket AM2 / AM2+
Processeurs AMD Athlon 64 / Athlon 64 FX /
Athlon 64 X2 / Sempron / AM2+
L'architecture AMD 64 permet le calcul 32 et 64
bits
Prend en charge Hyp er Transport 3.0 et
Cool’n’Quiet
Prend en ch arge Hype r Transp ort 3.0
bande passante de 5.2 GT/s
AMD 770
AMD SB600
ITE 8718F
Fournit la fonctionnalité de Super E/S
patrimoniales la plus utilisée.
Int e rface à f aible co mp te de b ro ch es
Initiatives de contrôle environnementales,
Mon iteur d e mat ériel
Contrôleur de vitesse de ventilateur
Fonction "Gardien intelligent" de l'ITE
Fentes DDR2 DIMM x 4
Chaque DIMM prend en charge des DDR2 de
512/1024/2048 Mo
Capac ité mémo ire max i male de 8 Go
Module de mémoire DDR2 à mode à double voie
Prend en charge la DDR2 533 / 667 / 800
Prend en charge la DDR2 1066 (by AM2+ CPU)
Les DIMM à registres et DIMM avec code
correcteurs d'err eurs ne sont pas prises en
charg e
Contrôleur IDE intégré
Mode principa le de Bus Ultra DMA 33 / 66 / 100 /
133
Prend en charge le mode PIO 0~4,
AMD SB600 (
Jmicro JMB36 2 (eSATA)
Taux de transfert jusqu'à 3 Go/s.
Co nforme à la sp éc if icat ion SATA Vers ion 2 .0
Prise en charge RAID 0,1,1+0 (embarqué)
Prise en charge NCQ/Port-Miltiplier/ RAID
0,1,5,0+1 (eSATA)
embarqué
(opt ion al)
)
(option al)
usqu'à une
46
Page 49
TA770 A2+
Ver 5.x Ver 6.x
LAN
Codec audio
Fentes
Connecteur
embarqué
E/S du
panneau
arrière
Dimensions
de la carte
Support SE
Marvell 88E8056 / 88E8039(optional)
10 / 100 / 1000 Mb /s négociation auto mat ique
(La bande passante Gigabit est pour le Marvell
88E80 56 uniquement)
Half / Full duplex capability
ALC888
Sortie aud io à 7 .1 vo ies
Prise en charge de l' aud io haute définit ion
Fente PCI x3 Fente PCI x3
Fente PCI Express Gen2 x16 x1 Fente PCI Express Gen2 x16 x1
Fente PCI Express Gen2 x1 x2 Fente PCI Express Gen2 x1 x2
Connecteur de disquette x1 Connecteur de disquette x1
Connecteur de Port d'imprimante x1 Connecteur de Port d'imprimante x1
Connecteur IDE x1 Connecteur IDE x1
Connecteur SATA x4 Connecteur SATA x4
Connecteur du panneau avant x1 Connecteur du panneau avant x1
Connecteur Audio du panneau avant x1 Connecteur Audio du panneau avant x1
Connecteur d' entrée CD x1 Co nnecteur d'entrée CD x1
Connecteur de sortie S/PDIF x1 Connecteur de sortie S/PDIF x1
Embase de ventilateur UC x1 Embase de ventilateur UC x1
Embase de ventilateur système x2 Embase de ventilateur système x2
Embase d'effacement CMOS x1 Embase d'effacement CMOS x1
Connecteur USB x2 Connecteur USB x2
Port série x1 Port série x1
Connecteur d' aliment at ion x 1
(24 broches)
Connecteur d' aliment at ion x1
(8 broch es)
Connecteur d' aliment at ion x1
(4 broch es)
Clavier PS/2 x1
Souris PS/2 x1
Port LA N x1
Port USB x6
Fiche aud io x6
Port eSATA
244 mm (l) X 305 mm (H) 244 mm (l) X 305 mm (H)
Windows XP / VISTA
Biostar se réserve le droit d'ajouter ou de
supprimer le support de SE avec ou sans préavis.
(option al)
x2
Marvell 88E8056 / 88E8039(optional)
10 / 100 / 1000 Mb /s négociation auto mat ique
(La bande passante Gigabit est pour le Marvell
88E80 56 uniquement)
Half / Full duplex capability
ALC662
Sortie aud io à 5 .1 vo ies
Prise en charge de l' aud io haute définit ion
Connecteur d' aliment at ion x 1
(24 broches)
Connecteur d' aliment at ion x1
(8 broch es)
Connecteur d' aliment at ion x1
(4 broch es)
Clavier PS/2 x1
Souris PS/2 x1
Port LA N x1
Port USB x6
Fiche aud io x3
Port eSATA
Windows XP / VISTA
Biostar se réserve le droit d'ajouter ou de
supprimer le support de SE avec ou sans préavis.
(option al)
x2
47
Page 50
Motherboard Manual
ITALIAN
Ver 5.x Ver 6.x
CPU
FSB
Chipset
Super I/O
Memoria
principale
IDE
SATA II
Socket AM2 / AM2+
Processori AMD Athlon 64 / Athlon 64 FX /
Athlon 64 X2 / Sempron / AM2+
L’arch itett ura A MD 64 abil ita la
computazione 32 e 64 bit
Supporto di Hyper Transport 3.0 e
Cool’n’Quiet
Supporto di HyperTransport 3.0 fino a 5.2
GT/s di larghezza di banda
AMD 770
AMD SB600
ITE 8718F
Fo rn isce le funz ional ità lega cy Super I/O
usate più comunemente.
Interfaccia LPC (Low Pin Count)
Funzioni di controllo dell’ambiente:
Monitoraggio hardware
Co ntro ller veloc it à vent olina
Funzione "Smart Guardian" di ITE
Alloggi DIMM DDR2 x 4
Ciascun DIMM supporta DDR2
512/1024/2048MB
Capacità massima della memoria 8GB
Modulo di memoria DDR2 a canale doppio
Supporto di DDR2 533 / 667 / 800
Supporto di DDR2 1066 (by AM2+ CPU)
DIMM r egistrati e DIMM ECC non sono
supportati
Co ntro ller IDE integr ato
Modalità Bus Master Ultra DMA 33 / 66 /
100 / 133
Supporto modalità PIO Mode 0-4
AMD SB600 (su scheda)
Jmicro JMB362 (eSATA) (optional)
Velocità di trasferimento dei dati fino a 3
Gb/s.
Co mpatibile s pecifiche SATA Vers ione 2 .0.
Supporto RAID 0,1,1+0 (su scheda)
Supporto NCQ/Port-Miltiplier/RAID
0,1,5,0+1 (eSATA) (optional)
Socket AM2 / AM2+
Processori AMD Athlon 64 / Athlon 64 FX /
Athlon 64 X2 / Sempron / AM2+
L’arch itett ura A MD 64 abil ita la
computazione 32 e 64 bit
Supporto di Hyper Transport 3.0 e
Cool’n’Quiet
Supporto di HyperTransport 3.0 fino a 5.2
GT/s di larghezza di banda
AMD 770
AMD SB600
ITE 8718F
Fo rn isce le funz ional ità lega cy Super I/O
usate più comunemente.
Interfaccia LPC (Low Pin Count)
Funzioni di controllo dell’ambiente:
Monitoraggio hardware
Co ntro ller veloc it à vent olina
Funzione "Smart Guardian" di ITE
Alloggi DIMM DDR2 x 4
Ciascun DIMM supporta DDR2
512/1024/2048MB
Capacità massima della memoria 8GB
Modulo di memoria DDR2 a canale doppio
Supporto di DDR2 533 / 667 / 800
Supporto di DDR2 1066 (by AM2+ CPU)
DIMM r egistrati e DIMM ECC non sono
supportati
Co ntro ller IDE integr ato
Modalità Bus Master Ultra DMA 33 / 66 /
100 / 133
Supporto modalità PIO Mode 0-4
AMD SB600 (su scheda)
Jmicro JMB362 (eSATA) (optional)
Velocità di trasferimento dei dati fino a 3
Gb/s.
Co mpatibile s pecifiche SATA Vers ione 2 .0.
Supporto RAID 0,1,1+0 (su scheda)
Supporto NCQ/Port-Miltiplier/RAID
0,1,5,0+1 (eSATA) (optional)
48
Page 51
TA770 A2+
Ver 5.x Ver 6.x
LAN
Codec
audio
Allo ggi
Connettori
su scheda
I/O
pannello
posteriore
Dimension
i scheda
Sistemi
operativi
supportati
Marvell 88E8056 / 88E8039(optional)
Negoziazione automatica 10 / 100 / 1000
Mb/s (la larghezza di banda Gigabit è solo
per Marvell 88E8056)
Capacità Half / Full Duplex
ALC888
Uscita audio 7.1 canali
Supporto audio High-Definition (HD)
Allo ggio PC I x3 A llogg io PC I x3
Alloggio PCI Express Gen2 x16 x1 Alloggio PCI Express Gen2 x16 x1
Alloggio PCI Express Gen2 x1 x2 Alloggio PCI Express Gen2 x1 x2
Connettore floppy x1 Connettore floppy x1
Connettore Porta stampante x1 Connettore Porta stampante x1
Connettore IDE x1 Connettore IDE x1
Connettore SATA x4 C onnett ore SATA x4
Connettore pannello frontale x1 Connettore pannello frontale x1
Connettore audio frontale x1 Connettore audio frontale x1
Connettore CD-in x1 Connettore CD-in x1
Connettore output SPDIF x1 Connettore output SPDIF x1
Co llet tor e vent olina C PU x1 Collett ore vento lina C PU x1
Co llet tor e vent olina s is tema x2 Co llet tore ventolina s is tema x 2
Co llet tor e cance llaz io ne CMO S x1 Co llet tor e cancellaz io ne CMO S x1
Connettore USB x2 Connettore USB x2
Porta seriale x1 Porta seriale x1
Connetto re alimentazione x 1
(24 pin)
Connetto re alimentazione x1
(8 pin)
Connetto re alimentazione x1
(4 pin)
Tas ti era PS/2 x 1
Mou se PS /2 x1
Porta LAN x1
Porta USB x6
Connettore audio x6
Porta eSATA(optional) x2
244 mm (larghezza) x 305 mm (altezza) 244 mm (larghezza) x 305 mm (altezza)
Windows XP / VISTA
Biostar si riserva il dir itto di aggiungere o
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
Marvell 88E8056 / 88E8039(optional)
Negoziazione automatica 10 / 100 / 1000
Mb/s (la larghezza di banda Gigabit è solo
per Marvell 88E8056)
Capacità Half / Full Duplex
ALC662
Uscita audio 5.1 canali
Supporto audio High-Definition (HD)
Connetto re alimentazione x 1
(24 pin)
Connetto re alimentazione x1
(8 pin)
Connetto re alimentazione x1
(4 pin)
Tas ti era PS/2 x 1
Mou se PS /2 x1
Porta LAN x1
Porta USB x6
Connettore audio x3
Porta eSATA(optional) x2
Windows XP / VISTA
Biostar si riserva il dir itto di aggiungere o
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
49
Page 52
Motherboard Manual
SPANISH
Ver 5.x Ver 6.x
Conector AM2 / AM2+
Procesadores AMD Athlon 64 / Athlon 64 FX /
Athlon 64 X2 / Sempron / AM2+
La arquitectura AMD 64 permite el procesado de
32 y 64 bits
Soporta las tecnologías Hyper Transport 3.0 y
Cool’n’Quiet
Admite HyperTransport 3.0 con un ancho de
banda de hasta 5.2 GT/s
AMD 770
AMD SB600
ITE 8718F
Le ofrece las funcionalidades heredadas de uso
más común Súper E/S.
Interfaz de cuenta Low Pin
In ic iativas d e co nt rol d e ent o rn o,
Monitor hardware
Controlador de velocidad de ventilador
Función "Guardia inteligente" de ITE
Ranuras DIMM DDR2 x 4
Cada DIMM admite DDR de 512/1024/2048MB
Capacidad máxima de memoria de 8GB
Módulo de memoria DDR2 de canal Doble
Admite DDR2 de 533 / 667 / 800
Admite DDR2 de 1066 (by AM2+ CPU)
No admite DIMM registrados o DIMM
comp atibles con ECC
Controlador IDE integrado
Modo bus maestro Ultra DMA 33 / 66 / 100 / 133
Soporte los Modos PIO 0~4,
AMD SB600 (en placa)
Jmicro JMB36 2 (eSATA) (opcional)
Tasas de transferencia de hasta 3 Gb/s.
Co mpat ible co n la ve rs ió n S ATA 2.0.
Admite RAID 0,1,1+0 (en placa)
Admite NCQ/Port-Multiplier/RAID 0,1,5,0+1
(eSATA) (opcional)
CPU
FSB
Conjunto de
chips
Súper E/S
Memoria
principal
IDE
SATA II
Conector AM2 / AM2+
Procesadores AMD Athlon 64 / Athlon 64 FX /
Athlon 64 X2 / Sempron / AM2+
La arquitectura AMD 64 permite el procesado de
32 y 64 bits
Soporta las tecnologías Hyper Transport 3.0 y
Cool’n’Quiet
Admite HyperTransport 3.0 con un ancho de
banda de hasta 5.2 GT/s
AMD 770
AMD SB600
ITE 8718F
Le ofrece las funcionalidades heredadas de uso
más común Súper E/S.
Interfaz de cuenta Low Pin
In ic iativas d e co nt rol d e ent o rn o,
Monitor hardware
Controlador de velocidad de ventilador
Función "Guardia inteligente" de ITE
Ranuras DIMM DDR2 x 4
Cada DIMM admite DDR de 512/1024/2048MB
Capacidad máxima de memoria de 8GB
Módulo de memoria DDR2 de canal Doble
Admite DDR2 de 533 / 667 / 800
Admite DDR2 de 1066 (by AM2+ CPU)
No admite DIMM registrados o DIMM
comp atibles con ECC
Controlador IDE integrado
Modo bus maestro Ultra DMA 33 / 66 / 100 / 133
Soporte los Modos PIO 0~4,
AMD SB600 (en placa)
Jmicro JMB36 2 (eSATA) (opcional)
Tasas de transferencia de hasta 3 Gb/s.
Co mpat ible co n la ve rs ió n S ATA 2.0.
Admite RAID 0,1,1+0 (en placa)
Admite NCQ/Port-Multiplier/RAID 0,1,5,0+1
(eSATA) (opcional)
50
Page 53
TA770 A2+
Ver 5.x Ver 6.x
Marvell 88E8056 / 88E8039 (opcional)
Negociación de 10 / 100 / 1000 Mb/s (el ancho
de banda Gigabit es únicamente para Marvell
88E8056)
Funciones Half / Full dúplex
ALC662
Salida de sonido de 5.1 canales
Soporte de sonido de Alta Definición
Conector de alimentación X1
(24 patillas)
Conector de alimentación X1
(8 patillas)
Conector de alimentación X1
(4 patillas)
Tec lad o PS /2 X 1
Ratón PS/2 X1
Puerto de red local X1
Puert o US B X 6
Conector de sonido X3
Puerto eSATA(op cional) X2
Windows XP / VISTA
Biostar se reserva el derecho de añadir o retirar
el soporte de cualquier SO con o s in aviso previo.
Red Local
Códecs de
sonido
Ranuras
Conectores
en p laca
Panel
trasero de
E/S
Ta mañ o d e
la placa
Soporte de
sistema
operativo
Marvell 88E8056 / 88E8039 (opcional)
Negociación de 10 / 100 / 1000 Mb/s (el ancho
de banda Gigabit es únicamente para Marvell
88E8056)
Funciones Half / Full dúplex
ALC888
Salida de sonido de 7.1 canales
Soporte de sonido de Alta Definición
Ranura PCI X3 Ranura PCI X3
Ranura PCI Express Gen2 x16 X1 Ranura PCI Express Gen2 x16 X1
Ranura PCI express Gen2 x1 X2 Ranura PCI express Gen2 x1 X2
Conector disco flexible X1 Conector disco flexible X1
Conector Puerto de impresora X1 Conector Puerto de impresora X1
Conector IDE X1 Conector IDE X1
Conector SATA X4 Conector SATA X4
Conector de panel frontal X1 Conector de panel frontal X1
Conector de sonido frontal X1 Conector de sonido frontal X1
Conector de entrada de CD X1 Conector de entrada de CD X1
Conector de salida S/PDIF X1 Conector de salida S/PDIF X1
Cabecera de ventilador de CPU X1 Cabecera de ventilador de CPU X1
Cabecera de ventilador de sistema X2 Cabecera de ventilador de sistema X2
Cabecera de borrado de CMOS X1 Cabecera de borrado de CMOS X1
Conector USB X2 Conector USB X2
Puert o s erie X1 Puerto ser ie X1
Conector de alimentación X1
(24 patillas)
Conector de alimentación X1
(8 patillas)
Conector de alimentación X1
(4 patillas)
Tec lad o PS /2 X 1
Ratón PS/2 X1
Puerto de red local X1
Puert o US B X 6
Conector de sonido X6
Puerto eSATA(op cional) X2
244 mm. (A) X 305 mm. (H) 244 mm. (A) X 305 mm. (H)
Windows XP / VISTA
Biostar se reserva el derecho de añadir o retirar
el soporte de cualquier SO con o s in aviso previo.
51
Page 54
Motherboard Manual
PORTUGUESE
Ver 5.x Ver 6.x
Socket AM2 / AM2+
Processadores AMD Athlon 64 / Athlon 64 FX /
Athlon 64 X2 / Sempron / AM2+
A arq uite ctura A MD 64 p erm ite uma computação
de 32 e 64 bits
Suporta as tecno log ias Hype r Transpo rt 3.0 e
Cool’n’Quiet
Suporta a tecnologia HyperTransport 3.0 com
uma largura de banda até 5.2 GT/s
AMD 770
AMD SB600
ITE 8718F
Proporciona as funcionalidades mais utilizadas
em termos da especificação Super I/O.
Interface LPC (Low Pin Count).
In ic iativas p ar a con tro lo do a mb iente
Monitorização do hardware
Controlador da velocidade da ventoinha
Função "Smart Guardian" d a ITE
Ranhuras DIMM DDR2 x 4
Cada módulo DIMM suporta uma memória
DDR2 de 512/1024/2048 MB
Capac idade máx ima de me mória: 8GB
Módulo de memória DDR2 de canal duplo
Suporta módulos DDR2 533 / 667 / 800
Suporta módulos DDR2 1066 (by AM2+ CPU)
Os módulos DIMM registados e os DIMM ECC
não são suportados
Controlador IDE integrado
Modo Bus master Ultra DMA 33 / 66 / 100 / 133
Suporta o modo PIO 0~4,
AMD SB600 (na placa)
Jmicro JMB36 2 (eSATA) (opcional)
Velocidades de transmissão de dados até 3 Gb/s.
Co mpat ibilidade co m a especif icação SATA
versão 2.0 .
Suporta as funçõ es RA ID 0,1 ,1+0 (n a p lac a)
Suporta as funções NCQ/Port-Mu ltip lier/RAID
0,1,5,0+1 (eSATA) (opcional)
CPU
FSB
Chipset
Especificaçã
o Super I/O
Memória
principal
IDE
SATA II
Socket AM2 / AM2+
Processadores AMD Athlon 64 / Athlon 64 FX /
Athlon 64 X2 / Sempron / AM2+
A arq uite ctura A MD 64 p erm ite uma computação
de 32 e 64 bits
Suporta as tecno log ias Hype r Transpo rt 3.0 e
Cool’n’Quiet
Suporta a tecnologia HyperTransport 3.0 com
uma largura de banda até 5.2 GT/s
AMD 770
AMD SB600
ITE 8718F
Proporciona as funcionalidades mais utilizadas
em termos da especificação Super I/O.
Interface LPC (Low Pin Count).
In ic iativas p ar a con tro lo do a mb iente
Monitorização do hardware
Controlador da velocidade da ventoinha
Função "Smart Guardian" d a ITE
Ranhuras DIMM DDR2 x 4
Cada módulo DIMM suporta uma memória
DDR2 de 512/1024/2048 MB
Capac idade máx ima de me mória: 8GB
Módulo de memória DDR2 de canal duplo
Suporta módulos DDR2 533 / 667 / 800
Suporta módulos DDR2 1066 (by AM2+ CPU)
Os módulos DIMM registados e os DIMM ECC
não são suportados
Controlador IDE integrado
Modo Bus master Ultra DMA 33 / 66 / 100 / 133
Suporta o modo PIO 0~4,
AMD SB600 (na placa)
Jmicro JMB36 2 (eSATA) (opcional)
Velocidades de transmissão de dados até 3 Gb/s.
Co mpat ibilidade co m a especif icação SATA
versão 2.0 .
Suporta as funçõ es RA ID 0,1 ,1+0 (n a p lac a)
Suporta as funções NCQ/Port-Mu ltip lier/RAID
0,1,5,0+1 (eSATA) (opcional)
52
Page 55
TA770 A2+
Ver 5.x Ver 6.x
LAN
Codec de
som
Ranhuras
Conectores
na placa
Entradas /S
aídas no
painel
traseiro
Tamanho
da placa
Sistemas
operativos
suportados
Marvell 88E8056 / 88E8039 (opcional)
Auto negociação de 10 / 100 / 1000 Mb/s (a
largura de banda Gigabit refere-se apenas à
especificação Marvell 88E8056)
Capacidade semi/full-duplex
ALC888
Saída de áudio de 7.1 canais
Suporta a especificação High-Definition Audio
Ranhura PCI x3 Ranhura PCI x3
Ranhura PCI Express Gen2 x16 x1 Ranhura PCI Express Gen2 x16 x1
Ranhura PCI Express Gen2 x1 x2 Ranhura PCI Express Gen2 x1 x2
Conector da unidade de disquetes x1 Conector da unidade de disquetes x1
Conector da para impressora x1 Conector da para impressora x1
Conector IDE x1 Conector IDE x1
Conector SATA x4 Conector SATA x4
Conector do painel frontal x1 Conector do painel frontal x1
Conector de áudio frontal x1 Conector de áudio frontal x1
Conecto r par a ent rada d e CDs x1 Co nector para entr ada d e CDs x 1
Conector de saída S/PDIF x1 Conector de saída S/PDIF x1
Conector da ventoinha da CPU x1 Conector da ventoinha da CPU x1
Conector da ventoinha do s istema x2 Conector da ventoinha do s istema x2
Conector para limpeza do CMOS x1 Conector para limpeza do CMOS x1
Conector USB x2 Conector USB x2
Porta série x 1 Porta s ér ie x1
Conector de alimentação x1
(24 pinos)
Conector de alimentação x1
(8 p inos )
Conector de alimentação x1
(4 p inos )
Tec lad o PS /2 x 1
Rato PS/2 x1
Porta LAN x1
Porta USB x6
Tomada de áudio x6
Porta eSATA(opcional) x2
244 mm (L) X 305 mm (A) 244 mm (L) X 305 mm (A)
Windows XP / VISTA
A Biostar reserva-se o direito de adicionar ou
remover suporte para qualquer sistema
operativo com ou sem aviso prévio.
Marvell 88E8056 / 88E8039 (opcional)
Auto negociação de 10 / 100 / 1000 Mb/s (a
largura de banda Gigabit refere-se apenas à
especificação Marvell 88E8056)
Capacidade semi/full-duplex
ALC662
Saída de áudio de 5.1 canais
Suporta a especificação High-Definition Audio
Conector de alimentação x1
(24 pinos)
Conector de alimentação x1
(8 p inos )
Conector de alimentação x1
(4 p inos )
Tec lad o PS /2 x 1
Rato PS/2 x1
Porta LAN x1
Porta USB x6
Tomada de áudio x3
Porta eSATA(opcional) x2
Windows XP / VISTA
A Biostar reserva-se o direito de adicionar ou
remover suporte para qualquer sistema
operativo com ou sem aviso prévio.
53
Page 56
Motherboard Manual
POLISH
Ver 5.x Ver 6.x
Procesor
FSB
Chipset
Pamięć
główna
Super I/O
IDE
SATA II
LAN
Socket AM2 / AM2+
AMD Athlon 64 / Athlon 64 FX / Athlon 64 X2 /
Sempron / AM2+ Procesory
Architektura AMD 64 umożliwia przetwarzanie
32 i 64 bitowe
Obsługa Hyper Transport 3.0 oraz Cool’n’Quiet
Obsługa HyperTransport 3.0 o szerokości pasma
do 5.2 GT/s
AMD 770
AMD SB600
Gniazda DDR2 DIMM x 4
Każde gniazdo DIMM obs ługuje moduły
512/1024/2048MB DDR2
Maks. wielko ść pamięci 8GB
Mod uł pamięci DDR2 z trybem podwójnego
kana łu
Obsługa DDR2 533 / 667 / 800
Obsługa DDR2 1066 (by AM2+ CPU)
Brak obsług i Registered DIMM oraz ECC DIMM
ITE 8718F
Zapewnia najbardziej po wszechne funkcje Super
I/O.
Interfejs Low Pin Count
Funkcje kontroli warunków pracy,
Mon itor H /W
Kontroler prędkości wentylatora
Funkcja ITE "Sm art Gu ard ian"
Zintegrowany kontroler IDE
Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master
obsługa PIO tryb 0~4,
AMD SB600 (wbudowane)
Jmicro JMB36 2 (eSATA) (opcja)
Transfer danych do 3 Gb/s.
Zgodność ze specyfikacją SATA w wersji 2. 0.
Obsługa RAID 0,1,1+0 (wbudowane)
Obsługa NCQ/Port-Multiplier/RAID 0,1,5,0+1
(eSATA) (opcja )
Marvell 88E8056 / 88E8039 (opcja)
10 / 100 / 1000 Mb/s z automatyczn ą nego cjacją
szybkości (Pasmo gigabitowe wyłączn ie dla
Marvell 88E8056)
Działanie w trybie połowicznego/pełnego
dupleksu
Socket AM2 / AM2+
AMD Athlon 64 / Athlon 64 FX / Athlon 64 X2 /
Sempron / AM2+ Procesory
Architektura AMD 64 umożliwia przetwarzanie
32 i 64 bitowe
Obsługa Hyper Transport 3.0 oraz Cool’n’Quiet
Obsługa HyperTransport 3.0 o szerokości pasma
do 5.2 GT/s
AMD 770
AMD SB600
Gniazda DDR2 DIMM x 4
Każde gniazdo DIMM obs ługuje moduły
512/1024/2048MB DDR2
Maks. wielko ść pamięci 8GB
Mod uł pamięci DDR2 z trybem podwójnego
kana łu
Obsługa DDR2 533 / 667 / 800
Obsługa DDR2 1066 (by AM2+ CPU)
Brak obsług i Registered DIMM oraz ECC DIMM
ITE 8718F
Zapewnia najbardziej powszechne funkcje Super
I/O.
Interfejs Low Pin Count
Funkcje kontroli warunków pracy,
Mon itor H /W
Kontroler prędkości wentylatora
Funkcja ITE "Sm art Gu ard ian"
Zintegrowany kontroler IDE
Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master
obsługa PIO tryb 0~4,
AMD SB600 (wbudowane)
Jmicro JMB36 2 (eSATA) (opcja)
Transfer danych do 3 Gb/s.
Zgodność ze specyfikacją SATA w wersji 2. 0.
Obsługa RAID 0,1,1+0 (wbudowane)
Obsługa NCQ/Port-Multiplier/RAID 0,1,5,0+1
(eSATA) (opcja )
Marvell 88E8056 / 88E8039 (opcja)
10 / 100 / 1000 Mb/s z automatyczn ą nego cjacją
szybkości (Pasmo gigabitowe wyłączn ie dla
Marvell 88E8056)
Działanie w trybie połowicznego/pełnego
dupleksu
54
Page 57
TA770 A2+
Ver 5.x Ver 6.x
Kodek
dźwiękowy
Gniazda
Złącza
wbud owan e
Back Panel
I/O
Wymiary
płyty
Obsluga
systemu
operacyjne
go
ALC888
7.1 kanałowe wyjście audio
Obsługa H igh -Defin it ion Aud io
Gniazdo PCI x3 Gniazdo PCI x3
Gniazdo PCI Express Gen2 x16 x1 Gniazdo PCI Express Gen2 x16 x1
Gniazdo PCI Express Gen2 x1 x2 Gniazdo PCI Express Gen2 x1 x2
Złącze napędu dyskietek x1 Złącze n apędu dyskietek x1
Złącze Port drukarki x1 Złącze Port drukarki x1
Złącze IDE x1 Złącze IDE x1
Złącze SATA x4 Z łącze SATA x4
Złącze panela przedniego x1 Złącze panela przedniego x1
Przedn ie złącze aud io x 1 Przednie złącze aud io x1
Złącze wejścia CD x1 Złącze wejścia CD x1
Złącze wyjścia S/PDIF x1 Złącze wyjścia S/PDIF x1
Złącze głó wko we wentylatora
procesora x1
Złącze głó wkowe wentylatora systemowego x2 Złącze głó wkowe wentylatora systemowego x2
Złącze głó wkowe kaso wan ia
CMOS x1
Złącze USB x2 Złącze USB x2
Port sz erego wy x1 Port szeregowy x1
Złącze zasilania (24 pinowe) x1 Złącze zasilania (24 pinowe) x1
Złącze zas ilania (8 p ino we) x1 Złącze zasilan ia (8 p ino we) x1
Złącze zas ilania (4 p ino we) x1 Złącze zasilan ia (4 p ino we) x1
Klawiatura PS/2 x1
Mys z PS /2 x1
Port LA N x1
Port USB x6
Gniazdo audio x6
Port eSATA(opcja) x2
244 mm (S) X 305 mm (W) 244 mm (S) X 305 mm (W)
Windows XP / VISTA
Biostar zastrzega sobie prawo dodawania lub
odwoływ ania obs ług i dowo ln eg o systemu
operacyjnego b ez powiado mien ia.
ALC662
5.1 kanałowe wyjście audio
Obsługa H igh -Defin it ion Aud io
Złącze głó wko we wentylatora
procesora x1
Złącze głó wkowe kaso wan ia
CMOS x1
Klawiatura PS/2 x1
Mys z PS /2 x1
Port LA N x1
Port USB x6
Gniazdo audio x3
Port eSATA(opcja) x2
Windows XP / VISTA
Biostar zastrzega sobie prawo dodawania lub
odwoływ ania obs ług i dowo ln eg o systemu
operacyjnego b ez powiado mien ia.
55
Page 58
Motherboard Manual
RUSSIAN
Ver 5.x Ver 6.x
CPU
(центральн
ый
процессор)
FSB
Набо р
микросхем
Основная
память
Super I/O
IDE
SATA II
56
Гнездо AM2 / AM2+
Процессоры AMD Athlon 64 / Athlon 64 FX /
Athlon 64 X2 / Sempron / AM2+
Арх итектура A MD 64 разрешать обработка
данных на 32 и 64 бит
Поддержка Hyper Transport 3.0 и Cool’n’Quiet
Поддержка HyperTransport 3.0 с пропус кной
способностью до 5.2 GT/s
AMD 770
AMD SB600
Слоты DDR2 DIMM x 4
Каждый модуль DIMM поддерживает
512/1024/2048МБ DDR2
Максимальная ёмкость памяти 8ГБ
Мод ул ь памяти с двух канальн ым режимом
DDR2
Поддержка DDR2 533 / 667 / 800
Поддержка DDR2 1066 (b y AM2+ CPU)
Не поддерживает зарегистрированные
модули DIMM and ECC DIMM
ITE 8718F
Обеспечивает наиболее используемые
действующие фун кц ион альны е возмо жности
Super I/O.
Интерфейс с ни зким количеством выводов
Инициативы по охране окружающей среды,
Аппаратный монитор
Регул ятор скорости
Функция ITE "Smart Guardian"
(Интеллектуальная защита)
Встроенное устр ойс тво упр авл ени я
встроенными интерфейсами устро йств
Режим "хозяина" шины U ltra DMA 3 3 / 66 / 100
/ 133
Поддержка режима PIO 0~4,
AMD SB600 (Встроенный)
Jmicro JMB36 2 (eSATA) (дополнительно)
скорость передачи данных до 3 гигабит/с.
Соответствие специ фикации SATA верс ия 2.0.
Поддержка RAID 0,1,1+0 (Встроенный)
Поддержка NCQ/Port-Multiplier/RAID 0,1,5,0+1
(eSATA) (дополнительно)
Гнездо AM2 / AM2+
Процессоры AMD Athlon 64 / Athlon 64 FX /
Athlon 64 X2 / Sempron / AM2+
Арх итектура A MD 64 разрешать обработка
данных на 32 и 64 бит
Поддержка Hyper Transport 3.0 и Cool’n’Quiet
Поддержка HyperTransport 3.0 с пропус кной
способностью до 5.2 GT/s
AMD 770
AMD SB600
Слоты DDR2 DIMM x 4
Каждый модуль DIMM поддерживает
512/1024/2048МБ DDR2
Максимальная ёмкость памяти 8ГБ
Мод ул ь памяти с двух канальн ым режимом
DDR2
Поддержка DDR2 533 / 667 / 800
Поддержка DDR2 1066 (b y AM2+ CPU)
Не поддерживает зарегистрированные
модули DIMM and ECC DIMM
ITE 8718F
Обеспечивает наиболее используемые
действующие фун кц ион альны е возмо жности
Super I/O.
Интерфейс с ни зким количеством выводов
Инициативы по охране окружающей среды,
Аппаратный монитор
Регул ятор скорости
Функция ITE "Smart Guardian"
(Интеллектуальная защита)
Встроенное устр ойс тво упр авл ени я
встроенными интерфейсами устро йств
Режим "хозяина" шины U ltra DMA 3 3 / 66 / 100
/ 133
Поддержка режима PIO 0~4,
AMD SB600 (Встроенный)
Jmicro JMB36 2 (eSATA) (дополнительно)
скорость передачи данных до 3 гигабит/с.
Соответствие специ фикации SATA верс ия 2.0.
Поддержка RAID 0,1,1+0 (Встроенный)
Поддержка NCQ/Port-Multiplier/RAID 0,1,5,0+1
(eSATA) (дополнительно)
Page 59
TA770 A2+
Ver 5.x Ver 6.x
Локальна я
сеть
Звуко вой
кодек
Слоты
Встроенны
й разъём
Задняя
панель
средств
ввода-выв
ода
Разм ер
панели
Поддержка
OS
Marvell 88E8056 / 88E8039 (дополнительно)
Автоматическо е согласо вани е 10 / 100 / 1000
Мб/с (гигабитная про пускная способность
только для гигабитного физи ч ес ко го уровн я)
Частичная / полна я дуплексная способность
ALC888
Звуко вая поддержка High-D ef initio n
7.1канальный звуковой выхо д
Слот PCI x3 Слот PC I x3
Слот PCI Express Gen2 x16 x1 Слот PCI Express Gen2 x16 x1
Слот PCI Express Gen2 x1 x2 Слот PCI Express Gen2 x1 x2
Разъ ём НГМД x1 Разъ ём НГМД x1
Разъ ём Порт подклю чения
принтера x1
Разъ ём IDE x 1 Разъём IDE x 1
Разъ ём SATA x4 Ра зъ ём SATA x4
Разъ ём на лицевой панели x1 Разъ ём на лицевой панели x1
Входной звуковой разъём x1 Входной звуковой разъём x1
Разъ ём ввода для CD x1 Разъ ём ввода для CD x1
Разъ ём вывода для S/PDIF x1 Разъём вывода для S/PDIF x1
Контактирующее приспособление
вентил ятора центрального процессора x1
Контактирующее приспособление
вентил ятора системы x2
Открытое контактирующее приспособление
CMOS x1
USB- разъём x2 USB-разъём x2
Последо вательны й порт x1 Последоват ельный порт x1
Разъ ем питания (24 вывод) x1 Разъем питания (24 вы вод) x1
Разъ ем питания (8 вы вод) x1 Разъем питания (8 вывод) x1
Разъ ем питания (4 вы вод) x1 Разъем питания (4 вывод) x1
Клавиатура PS/2 x1
Мышь PS /2 x1
Пор т LAN x1
USB- порт x6
Гнездо для подключени я
наушников x6
eSATA порт(дополнительно) x2
244 мм (Ш) X 305 мм (В) 244 мм (Ш) X 305 мм (В)
Windows XP / VISTA
Biostar сохраняет за собой право добавлять
или удалять средства обеспечения для OS с
или без предварительного уведомлени я.
Marvell 88E8056 / 88E8039 (дополнительно)
Автоматическо е согласо вани е 10 / 100 / 1000
Мб/с (гигабитная про пускная способность
только для гигабитного физи ч ес ко го уровн я)
Частичная / полна я дуплексная способность
ALC662
Звуко вая поддержка High-D ef initio n
5.1канальный звуковой выхо д
Разъ ём Порт подклю чения
принтера x1
Контактирующее приспособление
вентил ятора центрального процессора x1
Контактирующее приспособление
вентил ятора системы x2
Открытое контактирующее приспособление
CMOS x1
Клавиатура PS/2 x1
Мышь PS /2 x1
Пор т LAN x1
USB- порт x6
Гнездо для подключени я
наушников x3
eSATA порт(дополнительно) x2
Windows XP / VISTA
Biostar сохраняет за собой право добавлять
или удалять средства обеспечения для OS с
или без предварительного уведомлени я.
57
Page 60
Motherboard Manual
ARABIC
ﺲﺒﻘﻡAM2 / AM2+
تﺎﺠﻟﺎﻌﻡAMD Athlon 64 / Athlon 64 FX / Athlon 64
X2 / S empron / AM2 +
ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗAMD 64 ﺔﻋﺮﺴﺏ ﺔﻴﺏﻮﺳﺎﺤﻟ ا تﺎﻴﻠﻤﻌﻟا ءاﺮﺝإ 32 و64 ﺖﺏ
ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyper Trans po rt و 3.0 Cool’n’Quiet
ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyperTransport ﻰﻟإ ﻞﺼﻳ ددﺮﺘﺏ 3.0 5.2 GT/s
AMD 770
AMD SB600
DIMM ﻢﻋﺪﺗ ةﺮآاذ ﻦﻡ عﻮﻥ DDR2 ﺔﻌﺳ
512/1024/2048
ةﺪﺣو ةﺮآاذ DDR2 ﺔﺝودﺰﻡ ةﺎﻨﻘﻟا
ﻢﻋﺪﺗ ةﺮآاﺬﻟا ﻦﻡ عﻮﻥ DDR2 تﺎﻌﺳ 800/667/533 ﺎﺠﻴﻡ ﺖﻳﺎﺏ
ﻢﻋﺪﺗ ةﺮآاﺬﻟا ﻦﻡ عﻮﻥ DDR2 تﺎﻌﺳ 1066(By AM2+ CPU)
ﻻ ﻢﻋﺪﺗ ﻖﺋﺎﻗر ةﺮآاﺬﻟا DIMM ﻚﻠﺗو ﻲﺘﻟا ﻻ ﻖﻓاﻮﺘﺗ ﻊﻡ ECC
ITE 8718F
ﺔﻔﻴﻇ و ﺮﻓﻮﺗSuper I/O ًﺎ ﻡاﺪﺨﺘ ﺳ ا ﺮﺜآﻷا .
ﺗﻢﻋﺪ ﺔﻴ ﻨﻘﺗ Low Pin Co unt Interface
ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو:
ةﺰﻬﺝﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻡ
ﺔﺣوﺮﻤﻟا ﺔﻋﺮﺳ ﻲﻓ ﺐﻗاﺮﻡ
ﺔﻔﻴﻇو"S mart Gu ard ian" ﻦﻡ IT E
ﻢﻜﺤﺘﻡIDE ﻞﻡﺎﻜﺘﻡ
ﺔﻴﻨﻘ ﺘﺏ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100 / 133
ﻲﺴﻴﺋر ﻊﺿو
ﻊﺿو ﻢﻋدPIO Mode 0~4
AMD SB600 ( ﻠﻋ ﺬﻓﺎﻨﻤﻟاﺔﺣﻮﻠﻟا ﺢﻄﺳ ﻰ )
Jmicro JMB36 2 (eSATA) ) يرﺎﻴﺘﺥا(
ﻰﻟإ ﻞﺼﺗ تﺎﻋﺮﺴﺏ تﺎ ﻥﺎﻴﺒ ﻟا ﻞﻘﻥ3 ﺖﺏﺎﺠﻴﺝ/ﺔﻴﻥ ﺎﺙ.
تﺎﻔﺹاﻮﻤﻟ ﺔﻘﺏﺎﻄﻡSATA راﺪﺹﻹا 2.0.
ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗRAID 0,1,1+0(ﺔﺣﻮﻠﻟا ﺢﻄﺳ ﻰﻠﻋ ﺬﻓﺎﻨﻤﻟا)
ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗRAID 0,1,5,0+1/NCQ/Port-Multiplier
)يرﺎﻴﺘﺥا( (eSATA)
ﻟﺎﻌﻡ تﺎﺠ AMD Athlon 64 / Athlon 64 FX / Athlon 64
X2 / S empron / AM2 +
ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗAMD 64 ﺔﻋﺮﺴﺏ ﺔﻴﺏﻮﺳﺎﺤﻟ ا تﺎﻴﻠﻤﻌﻟا ءاﺮﺝإ 32 و64 ﺖﺏ
ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyper Trans po rt و 3.0 Cool’n’Quiet
ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyperTransport ﻰﻟإ ﻞﺼﻳ ددﺮﺘﺏ 3.0 5.2 GT/s
ﺔﺤﺘﻓ DDR2 DIMM دﺪﻋ4
DIMM ﻢﻋﺪﺗ ةﺮآاذ ﻦﻡ عﻮﻥ DDR2 ﺔﻌﺳ
ﺎﺠﻴﻡ ﺖﻳﺎﺏ و1 ﺎﺠﻴﺝ ﺖﻳﺎﺏ
ﺔﻌﺳ ةﺮآاذ ىﻮﺼﻗ 8 ﺎﺠﻴﺝ ﺖﻳﺎﺏ
ﻢﻋﺪﺗ ةﺮآاﺬﻟا ﻦﻡ عﻮﻥ DDR2 تﺎﻌﺳ 800/667/533 ﺎﺠﻴﻡ ﺖﻳﺎﺏ
ﻢﻋﺪﺗ اةﺮآاﺬﻟ ﻦﻡ عﻮﻥ DDR2 تﺎﻌﺳ 1066(By AM2+ CPU)
ﺎﺠﻴﻡ ﺖﻳﺎﺏ
ﻻ ﻢﻋﺪﺗ ﻖﺋﺎﻗر ةﺮآاﺬﻟا DIMM ﻚﻠﺗو ﻲﺘﻟا ﻻ ﻖﻓاﻮﺘﺗ ﻊﻡ ECC
ﺔﻔﻴﻇ و ﺮﻓﻮﺗSuper I/O ًﺎ ﻡاﺪﺨﺘ ﺳ ا ﺮﺜآﻷا .
ﺗﻢﻋﺪ ﺔﻴ ﻨﻘﺗ Low Pin Co unt Interface
ﺔﻔﻴﻇو"S mart Gu ard ian" ﻦﻡ IT E
ﺔﻴﻨﻘ ﺘﺏ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100 / 133
ﻊﺿو ﻢﻋدPIO Mode 0~4
AMD SB600 ( ﺳ ﻰﻠﻋ ﺬﻓﺎﻨﻤﻟاﺔﺣﻮﻠﻟا ﺢﻄ )
Jmicro JMB36 2 (eSATA) ) يرﺎﻴﺘﺥا(
ﻰﻟإ ﻞﺼﺗ تﺎﻋﺮﺴﺏ تﺎ ﻥﺎﻴﺒ ﻟا ﻞﻘﻥ3 ﺖﺏﺎﺠﻴﺝ/ﺔﻴﻥ ﺎﺙ.
تﺎﻔﺹاﻮﻤﻟ ﺔﻘﺏﺎﻄﻡSATA راﺪﺹﻹا 2.0.
ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗRAID 0,1,1+0(ﺔﺣﻮﻠﻟا ﺢﻄﺳ ﻰﻠﻋ ﺬﻓﺎﻨﻤﻟا)
ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗRAID 0,1,5,0+1/NCQ/Port-Multiplier
ﺲﺒﻘﻡAM2 / AM2+
AMD 770
AMD SB600
512/1024/2048
ةﺪﺣو ةﺮآاذ DDR2 ﺔﺝودﺰﻡ ةﺎﻨﻘﻟا
ITE 8718F
ةﺰﻬﺝﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻡ
ﺔﺣوﺮﻤﻟا ﺔﻋﺮﺳ ﻲﻓ ﺐﻗاﺮﻡ
ﻢﻜﺤﺘﻡIDE ﻞﻡﺎﻜﺘﻡ
ﻲﺴﻴﺋر ﻊﺿو
)يرﺎﻴﺘﺥا( (eSATA)
ﺔﺤﺘﻓ DDR2 DIMM دﺪﻋ4
ﺎﺠﻴﻡ ﺖﻳﺎﺏ و1 ﺎﺠﻴﺝ ﺖﻳﺎﺏ
ﺔﻌﺳ ةﺮآاذ ىﻮﺼﻗ 8 ﺎﺠﻴﺝ ﺖﻳﺎﺏ
ﺎﺠﻴﻡ ﺖﻳﺎﺏ
ﺳوﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎ:
Ver 5.x Ver 6.x
ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو
ﺔﻳﺰآﺮﻤﻟا
ﻲﺒﻥﺎﺠﻟا ﻲﻡﺎﻡﻷا ﻞﻗﺎﻨﻟا
ﺢﺋاﺮﺸﻟا ﺔﻋﻮﻤﺠﻡ
ﺔﻴﺴﻴ ﺋﺮﻟا ةﺮآاﺬﻟا
Super I/O
ﺬﻔﻨﻡIDE
SATA II
58
Page 61
Marvell 88E8056 /88E8039 )يرﺎﻴﺘﺥا(
ضوﺎﻔﺗ ﻲﺋ ﺎﻘﻠﺗ 10/100 ﺎﺠﻴﻡ ﺖﻳﺎﺏ /ﺔﻴﻥﺎﺙ و1ﺎﺠﻴﺝ ﺖﺏ/ﺙﺔﻴﻥﺎ
قﺎﻄﻨﻟا يددﺮﺘﻟا ﺖﺏﺎﺠﻴﺠﻠﻟ رﻮﺼﻘﻡ ﻂﻘ ﻓ ﻰﻠ ﻋ Marvell 88E8056
ﺔﻴﻥﺎﻜﻡإ ﻞﻘﻨﻟا جودﺰﻤﻟا ﻞﻡﺎﻜﻟا/ﻲﻔﺼﻨﻟا
ALC662
ﻦﻡ ﻒﻳﺮﻌﺘﻟا ﻲﻟ ﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗ
5.1 تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ
ﺢﻴﺗﺎﻔﻡ ﺔﺣﻮﻟPS/2 دﺪﻋ1
سوﺎﻡ PS/2 دﺪﻋ1
ﺔﻴﻠﺤﻡ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻡ ﺪﻋ1
ﺬﻓﺎﻨﻡUSB دﺪﻋ6
تﻮﺹ ﺲﺒﻘﻡ دﺪﻋ3
ﺬﻔﻨﻡeSATA)يرﺎﻴﺘﺥا( دﺪﻋ2
Windows XP / VISTA
ﻆﻔﺘﺤﺗBiostar وأ رﺎﻄﺥﺈﺏ ﻞﻴﻐﺸﺗ مﺎﻈﻥ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿإ ﻲﻓ ﺎﻬﻘﺤﺏ
رﺎﻄﺥإ نوﺪﺏ.
TA770 A2+
Marvell 88E8056 /88E8039 )يرﺎﻴﺘﺥا(
ضوﺎﻔﺗ ﻲﺋ ﺎﻘﻠﺗ 10/100 ﺎﺠﻴﻡ ﺖﻳﺎﺏ /ﺔﻴﻥﺎﺙ و1ﺎﺠﻴﺝ ﺖﺏ/ﺔﻴﻥﺎﺙ
قﺎﻄﻨﻟا يددﺮﺘﻟا ﺖﺏﺎﺠﻴﺠﻠﻟ رﻮﺼﻘﻡ ﻂﻘ ﻓ ﻰﻠ ﻋ Marvell 88E8056
ﺔﻴﻥﺎﻜﻡإ ﻞﻘﻨﻟا جودﺰﻤﻟا ﻞﻡﺎﻜﻟا/ﻲﻔﺼﻨﻟا
ALC888
ﻦﻡ ﻒﻳﺮﻌﺘﻟا ﻲﻟ ﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗ
7.1 تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ
ﺔﺤﺘﻓPCI دﺪﻋ3 ﻓ ﺔﺤﺘPCI ﺪﻋ3
ﺔﺤﺘﻓGen2 x16 PCI Express دﺪﻋ1 ﺔﺤﺘﻓGen2 x16 PCI Express دﺪﻋ1
ﺔﺤﺘﻓPCI Express Gen2 x1 دﺪﻋ2 ﺔﺤﺘﻓPCI Express Gen2 x1 دﺪﻋ2
ﺔﻥﺮﻡ صاﺮﻗأ كﺮﺤﻡ ﺬﻔﻨﻡ دﺪﻋ1 ﺔﻥﺮﻡ صاﺮﻗأ كﺮﺤﻡ ﺬﻔﻨﻡ دﺪﻋ1
ﺔﻌﺏﺎﻃ ﺬﻔﻨﻡ دﺪﻋ1 ﺔﻌﺏﺎﻃ ﺬﻔﻨﻡ دﺪﻋ1
ﺬﻔﻨﻡIDE دﺪﻋ1 ﺬﻔﻨﻡIDE دﺪﻋ1
ﺬﻔﻨﻡSATA دﺪﻋ4 ﺬﻔﻨﻡSATA دﺪﻋ4
ﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟا ﺬﻔﻨﻡ دﺪﻋ1 ﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟا ﺬﻔﻨﻡ دﺪﻋ1
ﻲﻡﺎﻡﻷا تﻮﺼﻟا ﺬﻔﻨﻡ دﺪﻋ1 ﻲﻡﺎﻡﻷا تﻮﺼﻟا ﺬﻔﻨﻡ دﺪﻋ1
ﺬﻔﻨﻡCD-IN دﺪﻋ1 ﺬﻔﻨﻡCD-IN دﺪﻋ1
جﺮﺥ ﺬﻔﻨﻡS/PDIF دﺪﻋ1 جﺮﺥ ﺬﻔﻨﻡS/PDIF دﺪﻋ1
ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻡ ﺔﻠﺹو دﺪﻋ1 ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻡ ﺔﻠﺹو دﺪﻋ1
مﺎﻈﻨﻟا ﺔﺣوﺮﻡ ﺔﻠﺹو دﺪﻋ2 مﺎﻈﻨﻟا ﺔﺣوﺮﻡ ﺔﻠﺹو ﺪﻋ2
ﺢﺴﻡ ﺔﻠﺹوCMOS دﺪﻋ1 ﺢﺴ ﻡ ﺔﻠﺹوCMOS دﺪﻋ1
ﺬﻔﻨﻡUS B دﺪﻋ2 ﺬﻔﻨﻡUS B دﺪﻋ2
ﻲﻠﺴﻠﺴﺗ ﺬﻔ ﻨﻡ دﺪﻋ1 ﻲﻠﺴﻠﺴﺗ ﺬﻔﻨﻡ دﺪﻋ1
ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ )24سﻮﺏد( دﺪﻋ1 ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)24سﻮﺏد( دﺪﻋ1
ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)8ﺲﻴﺏﺎﺏد( دﺪﻋ1 ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)8ﺲﻴﺏﺎﺏد( دﺪﻋ1
ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)4ﺲﻴﺏﺎﺏد( دﺪﻋ1 ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)4ﺲﻴﺏﺎﺏد( دﺪﻋ1
ﺢﻴﺗﺎﻔﻡ ﺔﺣﻮﻟPS/2 دﺪﻋ1
سوﺎﻡ PS/2 دﺪﻋ1
ﺔﻴﻠﺤﻡ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻡ ﺪﻋ1
ﺬﻓﺎﻨﻡUSB دﺪﻋ6
تﻮﺹ ﺲﺒﻘﻡ دﺪﻋ6
ﺬﻔﻨﻡeSATA)يرﺎﻴﺘﺥا( دﺪﻋ2
244 ﻢﻡ)ضﺮﻋ (X 305 ﻢﻡ)عﺎﻔﺗرا( 244 ﻢﻡ)ضﺮﻋ (X 305 ﻢﻡ)عﺎﻔﺗرا(
Windows XP / VISTA
ﻆﻔﺘﺤﺗBiostar وأ رﺎﻄﺥﺈﺏ ﻞﻴﻐﺸﺗ مﺎﻈﻥ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿإ ﻲﻓ ﺎﻬﻘﺤﺏ
رﺎﻄﺥإ نوﺪﺏ.
Ver 5.x Ver 6.x
ﺔﻴﻠﺥاد ﺔﻜﺒﺵ
تﻮﺼﻟا ﻚﻳدﻮآ
تﺎﺤﺘﻔﻟا
ﺢﻄﺳ ﻰﻠﻋ ﺬﻓﺎﻨﻤﻟا
ﺔﺣﻮﻠﻟا
ﻞﺥد ﺬﻓﺎﻨﻡ/ جﺮﺥ
ﺔﻴﻔﻠﺨﻟا ﺔﺣﻮﻠﻟا
ﺔﺣﻮﻠﻟا ﻢﺠﺣ
ﻞﻴﻐﺸﺘﻟا ﺔﻤﻈﻥأ ﻢﻋد
59
Page 62
Motherboard Manual
JAPANESE
Ver 5.x Ver 6.x
CPU
FSB
チップセット
メインメモリ
Super I/O
IDE
SATA II
60
Socket AM2 / AM2+
AMD Athlon 64 / Athlon 64 FX / Athlon 64 X2 /
Sempron / AM2+ プ ロセッサ
AMD 64アーキ テクチャで は、32ビ ットと64ビッ ト計
算が可能です
ハイパートラ ンス ポート3.0と クールアン ドクワイア
ットをサポー トし ます
5.2 GT/sのバンド 幅まで ハイパート ランスポー ト3.0
をサポートし ます
AMD 770
AMD SB600
DDR2 DIMMスロット x 4
各DIMMは 51 2/1024/2048 MB DDR2をサポ ート
最大メモリ容 量8GB
デュアル チ ャン ネルモードDDR2メモリモジ ュール
DDR2 533 / 667 / 800をサポー ト
DDR2 1066をサ ポート (by AM2+ CP U)
登録済みDIMMとECC DIMMはサポ ートされま せん
ITE 8718F
もっとも一般 に使 用されるレ ガシーSuper I/O機能を
採用していま す。
低ピンカウン トイ ンターフェ イス
環境コントロ ール イニシアチ ブ、
H/Wモニター
ファン速度コ ント ローラ/ モニター
ITE の「スマート ガー ディアン」 機能
統合ID Eコントローラ
Ultra DMA 33 / 66 / 100 / 133バスマ スタモード
PIO Mode 0~4のサポート 、
AMD SB600 (オン ボードコネ クタ )
Jmicro JMB36 2 (eSATA) (オプション )
最高3 Gb/秒の データ転送 速度
SATAバージョン2.0仕様に準拠。
RAID 0,1,1+0のサ ポート(オンボ ードコネク タ)
RAID 0,1,5,0+1/NCQ/Port-Multiplierのサポー ト
(eSATA) (オプ ショ ン)
Socket AM2 / AM2+
AMD Athlon 64 / Athlon 64 FX / Athlon 64 X2 /
Sempron / AM2+ プ ロセッサ
AMD 64アーキ テクチャで は、32ビ ットと64ビッ ト計
算が可能です
ハイパートラ ンス ポート3.0と クールアン ドクワイア
ットをサポー トし ます
5.2 GT/sのバンド 幅まで ハイパート ランスポー ト3.0
をサポートし ます
AMD 770
AMD SB600
DDR2 DIMMスロット x 4
各DIMMは 51 2/1024/2048 MB DDR2をサポ ート
最大メモリ容 量8GB
デュアル チ ャン ネルモードDDR2メモリモジ ュール
DDR2 533 / 667 / 800をサポー ト
DDR2 1066をサ ポート (by AM2+ CP U)
登録済みDIMMとECC DIMMはサポ ートされま せん
ITE 8718F
もっとも一般 に使 用されるレ ガシーSuper I/O機能を
採用していま す。
低ピンカウン トイ ンターフェ イス
環境コントロ ール イニシアチ ブ、
H/Wモニター
ファン速度コ ント ローラ/ モニター
ITE の「スマート ガー ディアン」 機能
統合ID Eコントローラ
Ultra DMA 33 / 66 / 100 / 133バスマ スタモード
PIO Mode 0~4のサポート 、
AMD SB600 (オン ボードコネ クタ )
Jmicro JMB36 2 (eSATA) (オプション )
最高3 Gb/秒の データ転送 速度
SATAバージョン2.0仕様に準拠。
RAID 0,1,1+0のサ ポート(オンボ ードコネク タ)
RAID 0,1,5,0+1/NCQ/Port-Multiplierのサポー ト
(eSATA) (オプ ショ ン)
Page 63
TA770 A2+
Ver 5.x Ver 6.x
Marvell 88E8056 / 88E8039 (オプショ ン)
LAN
サウンド
Codec
オンボードコ
ネクタ
背面パネル
I/O
ボードサイズ 244 mm (幅) X 305 mm (高さ) 244 mm (幅) X 305 mm (高さ)
OSサポー ト
10 / 100 / 1000 Mb/秒のオート ネゴシエー ション
(G igab itバ ンド幅 はMarvell 88E8056専用です )
半/全二重機能
ALC888
ハイデフィニ ショ ンオーディ オのサポー ト
7.1 チ ャンネルオ ーディ オアウト
PCIスロット x3 PCIスロット x3
PCI Express Gen2 x16スロット x1 PCI Express Gen2 x16スロット x1 スロット
PCI Express Gen2 x1スロ ット x2 PCI Express Gen2 x1スロ ット x2
フロッピーコ ネク タ x1 フロッピーコネク タ x1
プリンタポー トコ ネクタ x1 プリンタポートコ ネクタ x1
IDE コネクタ x1 IDEコネクタ x1
SATAコネクタ x4 SATAコネクタ x4
フロントパネ ルコ ネクタ x1 フロントパネルコ ネクタ x1
フロントオー ディ オコネクタ x1 フロン トオー ディオコネ クタ x1
CDインコネクタ x1 CDインコネクタ x1
S/PDIFアウトコネ クタ x1 S/PDIFアウトコネ クタ x1
CPUファンヘッダ x1 CPUファンヘッダ x1
システムファ ンヘ ッダ x2 システムファ ンヘ ッダ x2
CMOSクリアヘッダ x1 CMOSクリアヘッダ x1
USBコネク タ x2 USBコネクタ x2
シリアルポー ト x1 シリア ルポート x1
電源コネクタ (24 ピン) x1 電源コネクタ (24 ピン) x1
電源コネクタ (8ピン) x1 電源コ ネクタ (8ピン) x1
電源コネクタ (4ピン) x1 電源コ ネクタ (4ピン) x1
PS/2キーボード x1
PS/2マウス x1
LANポート x1
USBポート x6
オーディオジ ャッ ク x6
eSATAポート (オプション) x2
Windows XP / VISTA
Biostarは事前の サポートな しにOSサ ポー トを追加ま
たは削除する 権利 を留保しま す。
Marvell 88E8056 / 88E8039 (オプショ ン)
10 / 100 / 1000 Mb/秒のオート ネゴシエー ション
(G igab itバ ンド幅 はMarvell 88E8056専用です )
半/全二重機能
ALC662
ハイデフィニ ショ ンオーディ オのサポー ト
5.1 チ ャンネルオ ーディ オアウト
PS/2キーボード x1
PS/2マウス x1
LANポート x1
USBポート x6
オーディオジ ャッ ク x3
eSATAポート (オプション) x2
Windows XP / VISTA
Biostarは事前の サポートな しにOSサ ポー トを追加ま
たは削除する 権利 を留保しま す。
2008/01/21
61
Loading...