Biostar G41-M7 Owner's Manual

G41-M7 Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ............................................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation ............................................. 5

2.1 Installing Central Processing Unit (CPU)....................................... 5

2.2 FAN Headers...................................................................................... 7

2.3 Installing System Memory ................................................................ 8

2.4 Connectors and Slots....................................................................... 10

Chapter 3: Headers & Jumpers Setup ..................................... 12

3.1 How to Setup Jumpers .................................................................... 12

3.2 Detail Settings.................................................................................. 12

Chapter 4: Useful Help ............................................................ 18

4.1 Driver Installation Note.................................................................. 18

4.2 Software ............................................................................................ 19

4.3 Extra Information............................................................................ 23

4.4 AMI BIOS Beep Code....................................................................... 25

4.5 Troubleshooting............................................................................... 26

Appendix: SPEC In Other Languages ...................................... 28

German.................................................................................................................. 28

French .................................................................................................................... 30

Italian..................................................................................................................... 32

Spanish ................................................................................................................... 34

Portugue se ............................................................................................................ 36

Polish...................................................................................................................... 38

Russian ................................................................................................................... 40

Arabic..................................................................................................................... 42

Japanese ................................................................................................................ 44

CHAPTER 1: INTRODUCTION

G41-M7

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short
circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

1.2 PACKAGE CHECKLIST

HDD Cable X 1
Serial ATA Cable X 1
Rear I/O Panel for ATX Case X 1
Installation Guide X 1
Fully Setup Driver CD X 1 (full version manual files inside)
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
Serial ATA Power Cable X 1 (optional)

Note: The package contents may be different due to area or your motherboard version.

1

Motherboard Manual

1.3 MOTHERBOARD FEATURES

LGA 775

Intel Core2Duo / Core2Quad /

CPU

FSB

Chipset

Super I/O

Main

Memory

Graphics

IDE

SATA 2

LAN

Sound

Codec

Slots

On Board

Connectors

2

Pent iu m Dua l-Co re / C eleron Du al-Co re /

Celeron 4xx processor

(Maximum Watt: 95W)

Support 800 / 1066 / 1333 MHz

Intel G41

Int e l ICH7

ITE 8718F

Prov ides the mos t commonly us ed legacy

Super I/O functionality.

Low Pin Count Interface

DIMM Slots x 2

Each DIMM supports 256MB / 512MB /

1GB / 2GB DDR2

Max Memory Capicity 4GB

GMA X4500 Max Shared Video Memory is 256MB

Int egr ated IDE Co ntr o lle r

Integrated Serial ATA Controller

Realtek RTL 8102EL

ALC662

PCI slot x2 Supports PCI expansion cards

PCI Express x 16 slot x1 Supports PCI-E x16 expansion cards

Floppy Connector x1 Each connector supports 2 Floppy drives

Printer Port Connector x1 Each connector supports 1 Printer port

Serial port Connector x1 Connects to RS-232 Port

IDE Conn ecto r x1 Each connector supports 2 IDE device

SATA Connector x4 Each connector suppo rts 1 S ATA devices

SPEC

Supports Hyper-Threading / Execute Disable Bit /

Enhanced Inte l SpeedStep® / Int el Arch itecture-64 /

Extended Memory 64 Technology / Virtualization

Technology

En viro nment C o ntrol in itiat ives,

Hardware Monitor Controller

Fan Sp eed Contro ller

ITE's "S mart Guard ian" funct ion

Dual Channe l Mode DDR 2 me mory mo dule

Supports DDR2 800/667

Register ed DIMM and ECC D IMM is not supported

Ultra DMA 33 / 66 / 100 Bus Master Mode

supports PIO Mode 0~4

Data transfer rates up to 3.0 Gb/s.

SATA Version 2.0 spe c if icat ion co mpl iant

10 / 100 Mb/s auto negot iation

Half / Full duplex capability

5.1 channels audio out

High Definition Audio

Back Panel

I/O

Board Size

OS Support

1.4 R

G41-M7

SPEC

Front Panel Connector x1 Supports front panel facilities

Front Audio Connector x1 Supports front panel audio function

CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)

System Fan Header x1 System Fan Power supply

Clear CMOS Head er x1 Res tore CMOS data to fact ory def ault

USB Connector x2 Each connector supports 2 front panel USB ports

Power Connector (24pin) x1 Connects to Power supp ly

Power Connector (4pin) x1 Connects to Power supply

PS/2 Keybo ard x1

PS/2 Mous e x1

VGA port x1

LAN port x1

USB Port x4

Audio Jack x3

182 (W) x 235 (L) mm

Windows 2000 / XP / Vista 32 / Vista 64

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to D-SUB monitor

Connect to RJ-45 ethernet cab le

Connect t o USB devices

Provide Audio-In/Out and microphone connection

Biostar reserves the right to add or remove support for

any OS with or without notice

EAR PANEL CONNECTORS

PS/ 2
Mouse

LAN

Line In/
Surround

Line Out

Mic In 1/
Bass/ Center

PS/2

VGA

USBX2USBX2

Keyboard

Since the audio chip supports High Definition Audio Specification, the function of each audio
jack can be defined by software. The input / output function of each audio jack listed above
represents the default setting. However, when connecting external microphone to the audio port,
please use the Line In (blue) and Mic In (Pink) audio jack.

3

Motherboard Manual

1.5 MOTHERBOARD LAYOUT

JKBMS1

LGA775

JATXPWR1

JVGA1

CPU1

JAT XPWR2

DDR2_B1

DDR2_A1

JUSB1

JCFAN1

JU SBV1

Intel

G41

JRJ45USB1

BIOS

FDD1

BATTERY

PEX1 6_ 1

PCI1

PCI2

JCOM1

JSFAN1

JAUDIO1

JAUDIO F1

LAN

Super

I/O

JPRNT1

Codec

Note: ■ represents the 1st pin.

JUSBV2

JP ANEL 1 JCMO S1

Intel

ICH7

JUSB2

JUSB3

SATA1 SATA2

IDE 1

SATA4

SATA3

4

CHAPTER 2: HARDWARE INSTALLATION

G41-M7

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Special Notice:

Remove Pin Cap before installation, and make good preservation
for future use. When the CPU is removed, cover the Pin Cap on the
empty socket to ensure pin legs won’t be damaged.

Pin-Cap

Step 1: Pull the socket locking lever out from the socket and then raise

the lever up to a 90-degree angle.

5

Motherboard Manual

Step 2: Look for the triangular cut edge on socket, and the golden dot on

CPU should point forwards this triangular cut edge. The CPU will
fit only in the correct orientation.

Step 2-1:

Step 2-2:

Step 3: Hold the CPU down firmly, and then lower the lever to locked

position to complete the installation.

Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it

on the retention frame. Connect the CPU FAN power cable into
the JCFAN1. This completes the installation.

6

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different due to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.

JCFAN1: CPU Fan Header

Pin

Assignment

1 Ground
2 Power

41

JSFAN1: System Fan Header

3 FAN RPM rate sense
4 Smart Fan Control

Pin

Assignment

1 Ground
2 +12V
3 FAN RPM rate sense

G41-M7

13

Note:

JCFAN1 supports 4-pin head connector; JSFAN1, 3-pin head one. When connecting
with wires onto connectors, please note that the red wire is the positive and should be
connected to pin#2, and the black wire is Ground and should be connected to GND.

7

Motherboard Manual

2.3 INSTALLING SYSTEM MEMORY

A. DDR2 module

DDR2_B1

DDR2_A1

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.

8

B. Memory Capacity

G41-M7

DIMM Socket

Location

DDR2_A1 256MB/512MB/1GB/2GB

DDR2_B1 256MB/512MB/1GB/2GB

DDR2 Module

Total Mem ory

Size

Max is 4GB.

C. Dual Channel Memory Installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status

Disabled O X

Disabled X O

Enabled O O

(O means memory installed; X, not installed.)

The DRAM bus width of the memory module must be the same(x8 or
x16)

DDR2_A1

DDR2_B1

9

Motherboard Manual

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.

234

133

IDE1: Hard Disk Connector

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100 functionality.

The IDE connector can connect a master and a slave drive, so you can connect
up to two hard disk drives.

40

2

39

1

10

PEX16_1: PCI-Express x16 Slot

- PCI-Express 1.0a compliant.

- Maximum theoretical realized bandwidth of 4GB/s simultaneously per

direction, for an aggregate of 8GB/s totally.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

- 2X bandwidth over the traditional PCI architecture.

PEX16_1

PCI1/PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

G41-M7

PCI1

PCI2

11

Motherboard Manual

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

JPANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.

PWR_LE D

On/Off

-

SPK

++

+

HLED

-

16

8

RST

9
1

12

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A

2 N/A 10 N/A

3 N/ A 11 N/ A N/A

4 Speaker

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

7 Ground 15 Power button

8 Reset control

Speaker
Connector

Hard drive
LED

Reset button

12 Power LED (+)

14 Power LED (-)

16 Ground

N/A

Power LED

Power-on button

JATXPWR2: AT X P ower Source Connector

This connector allows user to connect 24-pin power connector on the ATX
power supply.

G41-M7

12

1

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V

24

13

JATXPWR1: AT X P ower Source Connector

By connecting this connector, it will provide +12V to CPU power circuit.

34

12

Pin

Assignment

1 +12V
2 +12V
3 Ground
4 Ground

Note:

Before you power on the system, please make sure that both JATXPWR1 and
JATXPWR2 connectors have been plugged-in.

13

Motherboard Manual

JUSB2/JUSB3: Headers for USB 2.0 Ports at Front Panel

This motherboard provides 2 USB 2.0 headers, which allows user to connect
additional USB cable on the PC front panel, and also can be connected with
internal USB devices, like USB card reader.

JUSB2
JUSB3

2

10

Pin Assignment

1 +5V (fused)
2 +5V (fused)
3 USB­4 USB­5 USB+
6 USB+
7 Ground
8 Ground
9 Key

10 NC

19

JAUDIOF1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.

Pin Assignment

1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO

10

9

1

2

5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in

10 Jack Sense

14

G41-M7

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and
the CMOS data. Please carefully follow the procedures to avoid damaging the
motherboard.

3

1

Pin 1-2 Close:

Normal Operation
(Default).

3

1

3

1

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

SATA1~SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4channels SATA interface, it
satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.

Pin Assignment

1 Ground
2 TX+
3 TX­4 Ground
5 RX­6 RX+

SATA4
SATA3

SATA1 SATA2

7 Ground

147

15

Motherboard Manual

JUSBV1/JUSBV2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBV1: +5V for USB ports at USB1/JRJ45USB1.

JUSBV2: +5V for USB ports at USB2/USBB3.

Pin 2-3 Close:

JUSBV1: +5V STB for USB ports at USB1/JRJ45USB1.

JUSBV2: +5V STB for USB ports at USB2/USBB3.

JUSBV1

1

3

JUSBV2

JCOM1: Serial port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

2

1

10

9

1

3

Pin 1-2 close

Pin 2-3 close

Pin

1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal ready
5 Signal ground
6 Data set ready
7 Request to send
8 Clear to send
9 Ring indicator

10 Key

1

3

Assignment

16

JPRNT1: Printer Port Connector

This header allows you to connector printer on the PC.

2

G41-M7

1

25

Pin Assignment Pin Assignment

1 -Strobe 14 Ground
2 -ALF 15 Data 6
3 Data 0 16 Ground

4 -Error 17 Data 7
5 Data 1 18 Ground

6 -Init 19 -ACK
7 Data 2 20 Ground
8 -Scltin 21 Busy

9 Data 3 22 Ground
10 Ground 23 PE

11 Data 4 24 Ground
12 Ground 25 SCLT
13 Data 5 26 Key

17

Motherboard Manual

CHAPTER 4: USEFUL HELP

4.1 D

RIVER INSTALLATION NOTE

After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.

You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader so ftware from
http://www.adobe.com/products/acrobat/readstep2.html

18

G41-M7

e

4.2 SOFTWARE

Installing Software

1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.

2. Select Software Installatio n, and then click on the respective software
title.

3. Follow the on-screen instructions to complete the installation.

Launching Software

After the installatio n process, you will see the software icon “eHOT Line” /
“BIOS Update” appears on the desktop. Double-click the icon to launch the
utility.

eHot-Line (Optional)

eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.

Before you use this uti lity, please set Outlook Express as yo ur default e-mail client applicatio n progra m.

re pr esent s im por ta nt

*

information that you
must provide. Without
this inf ormation, you may
not be able to send out
the mail.

This block will show
the information which
would be collected in
the mail.

Describe condition

*

of your system.

Select your area or

*

the area cl os e to you.

Provide the e-mail
address that you would
like to s end the copy to.

Pr ovid e the na me of

*

the memor y module
manufacturer.

Provide the name of
th e powe r su ppl y
manufacturer and the
model no.

Se nd th e mai l out .

Sav e the se info rma tion t o a .t xt fil

Exit this dialog.

19

Motherboard Manual

After filling up this informatio n, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click

“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialog appears asking you to enter file name.

Enter the file name and then click
“Save”. Your system information

will be saved to a .txt file.

20

Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.

We will not share customer ’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.

If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web

http://www.biostar.com.tw/app/en-us/about/contact.php for getting

our contact information.

BIOS Update

BIOS Update is a convenient utility which allows you to update your
motherboard BIOS under Windows system.

G41-M7

AWARD BIOS AMI BIOS

Clear CMOS function

(Only for AWARD BIOS)

Show current BIOS information

Save cur rent B IOS

to a .bin file

Update BIOS

with a BIOS file

<Backup BIOS>

Once click on this button, the saving
dialog will show. Choose the
position to save file and enter file
name. (We recommend that the file
name should be English/number
and no longer than 7 characters.)
Then click Save.

After the saving process, finish
dialog will show. Click on OK to

complete the BIOS Backup
procedure.

21

Motherboard Manual

<Update BIOS>

Before doing this, please download the proper BIOS file from the website.

For AWARD BIOS, update BIOS procedure
should be run with Clear CMOS function, so
please check on Clear CMOS first.

Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.

After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.

The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.

After the BIOS Update process, click on
OK to restart the system.

While the system boots up and the full screen logo shows, press <Delete>
key to enter BIOS setup.

In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.

All the information and content above about the software are subject to be changed
without notice. For better performance, the software is being co ntinuously updated.
The information and pictures described above are for your reference only. The actual
information and settings on board may be slightly different from this manual.

22

4.3 EXTRA INFORMATION

CPU Overheated

If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection
function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

G41-M7

23

Motherboard Manual

BIO-Flasher

BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.

The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIO-Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, save the BIOS file into a USB pen drive or a floppy disk.

3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.

4. Power on or reset the computer and then
press <F12> during the POST process.
A select dialog as the picture on the right
appears.
Select the device contains the BIOS file and
press <Enter> to enter the utility.

24

5. The utility will show the BIOS
files and their respective
information. Select the proper
BIOS file and press <Enter>
then <Y> to perform the BIOS
update process.

6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.

z This utility only allows storage device with FAT32/16 format and single

parti tion.

z Shutting down or resetting the system while updating the B IOS will lead to

system boot failure.

4.4 AMI BIOS BEEP CODE

Boot Block Beep Codes

Number of Beeps Description

1 No media present. (Insert diskette in floppy drive A:)

2

3 Insert next diskette if multiple diskettes are used for recovery
4 Flash Programming successful
5 File read error

7 No Flash EPROM detected
10 Flash Erase error
11 Flash Program error
12 “AMIBOOT.ROM” file size error

13

POST BIOS Beep Codes

Number of Beeps Description

1 Memory refresh timer error

3 Base memory read/write test error

6 Keyboard controller BAT command failed

7 General exception error (processor exception interrupt error)

8 Display memory error (system video adapter)

“AMIBOOT.ROM” file not found in root directory of diskette in
A:

BIOS ROM image mismatch (file layout does not match
image present in flash device)

G41-M7

Troubleshooting POST BIOS Beep Codes

Number of Beeps Troubleshooting Action

1, 3 Reseat the memory, or replace with known good modules.

Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.

6, 7

8

z If beep codes are generated when all other expansion

cards are absent, consult your system manufacturer’s
technical support.

z If beep codes are not generated when all other expansion

cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.

If the system video adapter is an add-in card, replace or
reseat the
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.

25

Motherboard Manual

4.5 TROUBLESHOOTING

Probable Solution

1. There is no power in the system.
Power LED does not shine; the
fan of the power supply does not
work

2. Indicator light on keyboard does
not shine.

System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.

System does not boot from a hard disk
drive, but can be booted from optical
drive.

System only boots from an optical
drive. Hard disks can be read,
applications can be used, but system
fails to boot from a hard disk.

Screen message shows “Invalid
Configuration” or “CMOS Failure.”

System cannot boot after user installs a
second hard drive.

1. Make sure power cable is
securely plugged in.

2. Replace cable.

3. Contact technical support.

Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.

1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.

2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.

1. Back up data and applications
files.

2. Reformat the hard drive.
Re-install applications and data
using backup disks.

Review system’s equipment. Make sure
correct information is in setup.

1. Set master/slave jumpers
correctly.

2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

26

G41-M7

This page is intentionally left blank.

27

Motherboard Manual

APPENDIX: SPEC IN OTHER LANGUAGES

G

ERMAN

Sp ezif ika tio nen

LGA 775

Intel Core2Duo / Core2Quad /

CPU

FSB 800 / 1066 / 1333 MHz

Chipsatz

Super E/A

Arbeitsspeich

er

Grafik GMA X4500 Max. 256MB gemeinsam benutzter Videospeicher

Pent iu m Dua l-Co re / C eleron Du al-Co re /

Celeron 4xx Prozessoren

(Maximales Watt: 95W)

Intel G41

Int e l ICH7

ITE 8718F

Biet et die h äuf ig v erwend eten a lten Sup er

E/A-Funktionen.

Low Pin Count-Schnittstelle

DDR2 DIMM-Steckplätze x 2

Jeder DIMM unterstützt 256MB / 512MB /

1GB / 2GB DDR2.

Max. 4GB Arbeitsspeicher

Unterstützt Hyper-Threading / Execute Disable Bit /

Enhanced Inte l SpeedStep® / Int el Arch itecture- 64 /

Extended Memory 64 Technology / Virtualization

Technology

Umgebungskontrolle,

Hardware-Überwachung

Lüfterdrehzahl-Controller/-Überwachung

"Smart Guardian"-Funktion von ITE

Dual-Kanal DDR2 Speichermodul

Unterstützt DDR2 800/667

registrierte DIMMs. ECC DIMMs werden nicht

unterstützt.

IDE

SATA

LAN

HD

Audio-Unters

tützung

28

Int eg r ier t er ID E-Co ntro ller

Ultra DMA 33 / 66 / 100 Bus Master- Modus

Unterstützt PIO-Modus 0~4,

Datentransferrate b is zu 3.0Gb /s

Integrierter Serial ATA-Controller

Konform mit der SATA-Spezifikation Version 2.0.

10 / 100 Mb/s Auto-Negotiation

Realtek RTL 8102EL

Halb-/ Vollduplex-Funktion

Unterstützt High-Definition Audio

ALC662

5.1-Kanal-Audioausgabe

Sp ezif ika tio nen

G41-M7

Steckplätz e

Onboard-Ans

chluss

PCI-Steckp latz x 2

PCI Express x16 Steckplatz x1

Diskettenlaufwerkanschluss x1 Jeder Anschluss unterstützt 2 Diskettenlaufwerke

Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss

Serieller Anschluss x1

IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke

SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk

Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen

Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion

CPU-Lüfterstromversorgungsanschluss (mit Smart

CPU-Lüfter-Sockel x1

Fan -F un ktio n)

System-Lüfter-Sockel x1 System-Lüfter-Stromversorgungsanschluss

"CMOS löschen"-S ockel x1

Jeder Anschluss unterstützt 2

USB-Anschluss x2

Fronttafel-USB-Anschlüsse

Stromanschluss (24-polig) x1

St romansch luss (4-po lig ) x1

PS/2-Tastatur x1

PS/2-Maus x1

Rückseiten-E

/A

Platinengröße 182 mm (B) X 235 mm (L)

OS-Unterstüt

zung

VGA-Anschluss x1

LAN-Anschluss x1

USB-Anschluss x4

Audioanschluss x3

Windows 2000 / XP / Vista 32 / Vista 64

Biostar behält sich das Recht vor, ohne Ankündigung

die Unterstützung für ein Betriebssystem

hinzuzufügen oder zu entfernen.

29

Motherboard Manual

FRENCH

LGA 775

Processeurs Intel Core2Duo / Core2Quad

UC

Bus frontal

Chipset

Super E/S

Mémoire

principale

/ Pentium Dua l-Core / C eleron Dua l-Core /

Celeron 4xx

(Wat t maximu m : 95W)

800 / 1066 / 1333 MHz

Intel G41

Int e l ICH7

ITE 8718F

Fournit la fonctionnalité de Super E/S

patrimoniales la plus utilisée.

Int e rfa ce à f aib le co mpt e d e b roches

Fentes DDR2 DIMM x 2

Chaque D IMM prend en c harge des DDR2

de 256Mo / 512Mo / 1Go / 2Go

Capacit é mé mo ir e max imale de 4G o

SPEC

Prend en charge les technologies Hyper-Threading /

d'ex écut ion de b it de désact ivat ion / Intel SpeedSt ep®

opt imisée/ d ' arch itect ure Int e l 64 / d e mémo ire

étendue 64 / de virtua lisation

Initiatives de contrôle environnementales,

Mon iteur d e mat ériel

Contrôleur /moniteur de vitesse de ventilateur

Fonction "Gardien intelligent" de l'ITE

Modu le d e mémo ir e DDR2 à mode à doub le vo ie

Prend en charge la DDR2 800/667

Les DIMM à registres et DIMM avec code correcteurs

d'erreurs ne sont pas prises en charge

Graphiques GMA X4500 Mémoire vidéo partagée maximale de 256 Mo

IDE

SATA

LAN

Prise en

charg e

aud io HD

Fentes

Connecteur

embarqu é

Contrôleur IDE intégré

Contrô leur Serial ATA int é gr é

Realtek RTL 8102EL

ALC662

Fente PCI x2

Fente PC I Expres s x16 x1

Connecteur de disquette x1

Mode principale de Bus Ultra DMA 33 / 66 / 100

Prend en charge le mode PIO 0~4,

Taux de transfert jusqu'à 3.0Go/s.

Co nfo rme à la spécificat ion S ATA Vers ion 2. 0

10 / 100 Mb/s négociation automatique

Half / Full duplex capability

Prise en charg e de l'aud io haut e déf in ition

Sortie aud io à 5 .1 vo ies

Chaque co nnector prend en charge 2 lecteu rs de

disquettes

30

E/S du

panneau

arrière

Dimensions

de la carte

Support SE

G41-M7

SPEC

Connecteur de Port d'imprimante x1 Chaque connector prend en charge 1 Port d'imprimante

Port série x1

Connecteur IDE x1

Connecteur SATA x4

Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant

Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant

Embase de ventilateur UC x1

Embase de ventilateur système x1 Alimentation électrique du ventilateur système

Embase d'effacement CMOS x1

Connecteur USB x2

Connecteur d' aliment at ion x1

(24 broches)

Connecteur d' aliment at ion x1

(4 broch es)

Clavier PS/2 x1

Souris PS/2 x1

Port VGA x1

Port LAN x1

Port USB x4

Fiche aud io x3

182 mm (l) X 235 mm (H)

Windows 2000 / XP / Vista 32 / Vista 64

Chaque connect eur prend en ch arg e 2 périp hér iqu es

IDE

Chaque connect eur prend en ch arg e 1 périp hér iqu e

SATA

Alimentation électrique du ventilateur UC (avec fonction

de ventilateur intelligent)

Chaque connecteur prend en charge 2 ports USB de

panneau avant

Biostar se réserve le droit d'ajouter ou de supprimer le

support de SE avec ou sans préavis.

31

Motherboard Manual

ITALIAN

SPECIFICA

LGA 775

Processore Intel Core2Duo /

CPU

FS B 800 / 1066 / 1333 MHz

Chipset

Super I/O

Memoria

principale

Grafica GMA X4500 La memoria video condivisa massima è di 256MB

Core2Quad / Pentium Dual-Core /

Celeron Dual-Core / Celeron 4xx

(Watt massimo: 95W)

Intel G41

Int e l ICH7

ITE 8718F

Fo rnis ce le fun zionalit à leg acy S u per

I/O usate più comunemente.

Interfaccia LPC (Low Pin Count)

Alloggi DIMM DDR2 x 2

Ciascun DIMM supporta DDR2 256MB

/ 512MB / 1GB / 2GB

Capacità massima della memoria 4GB

Supporto di Hyper-Threading / Execute Disable

Bit / Enhanced Inte l SpeedSt ep® / Architettura

Intel 64 / Tecnologia Extended Memory 64 /

Tecnologia Virtualization

Funzioni di controllo dell’ambiente:

Monitoraggio hardware

Co ntroller / Mo nito raggio velo cità ven tolina

Funzione "Smart Guardian" di ITE

Modulo di memoria DDR2 a canale doppio

Supporto di DDR2 800/667

DIMM registrati e DIMM ECC non sono supportati

IDE Cont roller IDE integrato

SATA Controller Serial ATA integrato

LA N Realtek RTL 8102EL

Supporto

audio HD

Allo g gi

ALC662

Allo g gio PC I x2

Alloggio PCI Express x16 x1

32

Modalità Bus Master Ultra DMA 33 / 66 / 100

Supporto modalità PIO Mode 0-4

Velocità di trasferimento dei dati fino a 3.0Gb/s.

Co mp at ibile specifiche S ATA Vers ione 2.0.

Negoziazione automatica 10 / 100 Mb/s

Capacità Half / Full Dup lex

Supporto audio High-Definition (HD)

Uscita audio 5.1 canali

Connettori

su scheda

I/O

pannello

posteriore

G41-M7

SPECIFICA

Connettore floppy x1 Ciascun connettore supporta 2 unità Floppy

Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante

Porta seriale x1

Connettore IDE x1 Ciascun connettore supporta 2 unità IDE

Connettore SATA x4 Ciascun connettore supporta 1 unità SATA

Co nnettore p an nello fr ont ale x1 Sup port a i servizi de l p anne l lo fr ont ale

Connettore audio frontale x1 Supporta la funzione audio pannello frontale

Co llet t o re ven t olina C PU x 1

Co llet t o re ven t olina sistema x1 A limentazione ventol ina d i s is t ema

Co llet t o re can ce l laz ione CMOS x1

Connettore USB x2

Connettore alimentazione x 1

(24 pin)

Connettore alimentazione x1

(4 pin)

Tas t iera P S / 2 x1

Mou s e PS/2 x1

Porta VGA x1

Porta LA N x1

Porta USB x 4

Connettore audio x3

Alimentazione ventolina CPU (con funzione Smart

Fan)

Ciascun connettore supporta 2 porte USB

pannello frontale

Dimension

i scheda

Sistemi

operat ivi

supportati

182 mm (larghezza) x 235 mm

(altez za)

Windows 2000 / XP / Vista 32 / Vista

64

Biostar si riserva il diritto di aggiungere o

rimuovere il supporto di qualsiasi sistema

operativo senza preavviso.

33

Motherboard Manual

SPANISH

Especificación

LGA 775

Procesador Intel Core2Duo / Core2Quad /

CPU

FSB 800 / 1066 / 1333 MHz

Conjunto de

chips

Súper E/S

Memoria

principal

Gráficos GMA X4500 Memoria máxima de vídeo compartida de 256MB

Pent iu m Dua l-Co re / C eleron Du al-Co re /

Celeron 4xx

(Vatio máx imo: 95W)

Intel G41

Int e l ICH7

ITE 8718F

Le ofrece las funcionalidades heredadas de

us o más común Súper E /S.

Interfaz de cuenta Low Pin

Ranuras DIMM DDR2 x 2

Cada DIMM admite DDR de 256MB /

512MB / 1GB / 2GB

Capacidad máxima de memoria de 4GB

Admite Hyper-Threading / Bit de deshabilitación de

ejecución / Intel SpeedStep® Mejo rado / Intel

Architecture-64 / Tecnología Extended Memory 64 /

Tecnología de virtualización

In iciat iv as de con tro l d e ent o rno ,

Monitor hardware

Controlador/monitor de velocidad de ventilador

Función "Guardia inteligente" de ITE

Módulo de memoria DDR2 de canal Doble

Admite DDR2 de 800/667

No admite DIMM registrados o DIMM compatibles con

ECC

IDE Controlador IDE integrado

SATA Controlador ATA Serie Integrado

Red Local Realtek RTL 8102EL

Soporte de

sonido HD

Ranuras

ALC662

Ranura PCI X2

Ranura PCI Express x16 X1

34

Modo bus maestro Ultra DMA 33 / 66 / 100

Soporte los Modos PIO 0~4,

Tasas de transferencia de hasta 3.0 Gb/s.

Co mp at ible con la ve rsión SATA 2.0.

Negociación de 10 / 100 Mb/s

Funciones Half / Full dúplex

Soporte de sonido de Alta Definición

Salida de sonido de 5.1 canales

Conectores

en p laca

Panel

trasero de

E/S

G41-M7

Especificación

Conector disco flexible X1 Cada conector soporta 2 unidades de disco flexible

Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora

Puert o ser ie X1

Conector IDE X1 Cada conector soporta 2 dispositivos IDE

Conector SATA X4 Cada conector soporta 1 dispositivos SATA

Co nect o r de p anel f ron tal X1 Sop o rta ins t a laciones en e l p ane l fr ont a l

Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal

Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con

función Smart Fan)

Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema

Cabecera de borrado de CMOS X1

Conector USB X2 Cada conector soporta 2 puertos USB fro ntales

Conector de alimentación X1

(24 patillas)

Conector de alimentación X1

(4 patillas)

Tec lad o P S /2 X 1

Ratón PS/2 X1

Puerto VGA X1

Puerto de red local X1

Puert o USB X4

Conector de sonido X3

Ta mañ o d e

la placa

Soporte de

sistema

operativo

182 mm. (A) X 235 Mm. (H)

Windows 2000 / XP / Vista 32 / Vista 64

Biostar se reserva el derecho de añadir o retirar el

soporte de cualquier SO con o sin aviso previo.

35

Motherboard Manual

PORTUGUESE

LGA 775

Processador Intel Core2Duo / Core2Quad

CPU

FSB

Chipset

Especificaçã

o Super I/O

Memória

principal

Placa

gráf ica

IDE

SATA

LAN

Suporte

para áudio

de alta

definição

/ Pentium Dua l-Core / C eleron Dua l-Core /

Celeron 4xx

(Watt máximo: 95W )

800 / 1066 / 1333 MHz

Intel G41

Int e l ICH7

ITE 8718F

Proporciona as funcionalidades mais

utilizadas em termos da especificação

Super I/O.

Interface LPC (Low Pin Count).

Ranhuras DIMM DDR2 x 2

Cada módulo DIMM suporta uma

memória DDR2 de 256 MB / 512 MB / 1GB

/ 2GB

Capacidad e máx ima de me mó r ia:4 GB

GMA X4500 Memória de vídeo máxima partilhada: 256 MB

Controlador IDE integrado

Controlador Serial ATA integrado

Realtek RTL 8102EL

ALC662

ESPECIFICAÇÕES

Sup orta as tecno log ias Hyper-Threading / Execut e

Disab le Bit / Enhanced Int el SpeedStep® / Int el

Arquitecture -64 / Extended Memory 64 / Virtualization

In iciat iv as para co ntro lo do amb ien te

Monitorização do hardware

Controlador/Monitor da velocidade da ventoinha

Função "S mart Gu ard ian" da ITE

Módulo de memória DDR2 de canal duplo

Suporta módulos DDR2 800/667

Os módulos DIMM registados e os DIMM ECC não são

suportados

Modo Bus master Ultra DMA 33 / 66 / 100

Suporta o modo PIO 0~4,

Velocidades de transmissão de dados até 3.0 Gb/s.

Compat ibilidade co m a es pecificação SATA versão 2.0.

Auto negociação de 10 / 100 Mb/s

Capacidade semi/full-duplex

Suporta a especificação High-Definition Audio

Saída de áudio de 5.1 canais

36

Ranhuras

Conectores

na placa

Entradas/S

aídas no

painel

traseiro

Tamanho

da placa

Sistemas

operativos

suportados

G41-M7

ESPECIFICAÇÕES

Ranhura PCI x2

Ranhura PCI Express x16 x1

Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de d isquetes

Conector da para impressora x1 Cada conector suporta 1 Porta para impressora

Porta série x1

Conector IDE x1 Cada conector suporta 2 dispositivos IDE

Conector SATA x4 Cada conector suporta 1 dispositivo SATA

Conector do painel frontal x1 Para suporte de várias funções no painel frontal

Conector d e áud io fronta l x1 Suporta a fun ção de áud io no painel frontal

Conector da ventoinha da CPU x1

Conector da ventoinha do s istema x1 Alimentação da ventoinha do sistema

Conector para limpeza do CMOS x1

Conector USB x2 Cada conector suporta 2 portas USB no painel frontal

Conector de alimentação x1

(24 pinos)

Conector de alimentação x1

(4 p inos)

Tec lad o P S /2 x 1

Rato PS/2 x1

Porta VGA x1

Porta LA N x1

Porta USB x4

Tomada de áudio x3

182 mm (L) X 235 mm (A)

Windows 2000 / XP / Vista 32 / Vista 64

Aliment ação da vento inh a da CPU (com a fun ção S mart

Fan )

A Biostar reserva-se o direito de adicionar ou remover

suporte para qualquer sistema operativo com ou sem

av iso pr év io .

37

Motherboard Manual

POLISH

SPEC

Procesor

FSB

Chipset

Pamięć

główna

Graf ika

Super I/O

LGA 775

Procesor Intel Core2Duo / Core2Quad /

Pent iu m Dua l-Co re / C eleron Du al-Co re /

Celeron 4xx

(Maksymalny Watt: 95W)

800 / 1066 / 1333 MHz

Intel G41

Int e l ICH7

Gniazda DDR2 DIMM x 2

Każde gniazdo DIMM obs ługuje moduły

256MB / 512MB / 1GB / 2GB

Maks. wielkość pamięci 4GB

GMA X4500

ITE 8718F

Zapewnia najbardziej powszechne funkcje

Super I/O.

Interfejs Low Pin Count

Obsługa Hyper-Threading / Execute Disable Bit /

Enhanced Inte l SpeedStep® / Int el Arch itecture-64 /

Extended Memory 64 Technology / Virtualization

Technology

Mod uł pamięci DDR2 z trybem podwójnego kanału

Obsługa DDR2 800/667

Brak obsług i Regist er ed D IMM oraz ECC D IMM

Maks. wielkość współdz ielonej pam ięci video wynosi

256MB

Funkcje kontroli warunków pracy,

Mon itor H /W

Kontroler/Monitor prędkości went ylatora

Funkcja ITE "Smart Guard ian"

IDE

SATA

LAN

Obsługa

aud io HD

Gniazda

38

Zintegrowany kontroler IDE

Ultra DMA 33 / 66 / 100 Tryb Bus Master

obsługa PIO tryb 0~4,

Transfer danych do 3.0 Gb/s.

Zintegrowany kontroler Serial ATA

Zgodność ze specyfikacją SATA w wersji 2.0.

10 / 100 Mb/s z automatyczną negocjacją szybko ści

Realtek RTL 8102EL

Działanie w trybie połowicznego / pełn ego dupleksu

Obsługa H igh- Def inition A ud io

ALC662

5.1 kanałowe wyjście audio

Gniazdo PCI x2

Gniazdo PCI Express x16 x1

Złącza

wbud owan e

Back Panel

I/O

Wymiary

płyty

Obsluga

systemu

operacyjne

go

SPEC

Złącze napędu dyskietek x1 Każde złącze obs ługuje 2 napędy dyskietek

Złącze Port drukarki x1 Każde złącze obs ługuje 1 Port drukarki

Port szeregowy x1

Złącze IDE x1 Każde złącze obs ługuje 2 urządzenia IDE

Złącze SATA x4 Każde złącze obsługuje 1 urządzenie SATA

Złącze panela przedniego x1 Obsługa elementów panela przedniego

Przedn ie złącze audio x1 Obsługa funkcji audio na panelu przednim

Złącze głó wkow e went ylatora

procesora x1

Złącze głó wkow e went ylatora

systemowego x1

Złącze głó wkowe kasowan ia CMOS x 1

Złącze USB x2

Złącze zasilania (24 pinowe) x1

Złącze zas ilania (4 p ino we ) x1

Klawiatura PS/2 x1

Mys z PS /2 x1

Port VGA x1

Port LAN x1

Port USB x4

Gniazdo audio x3

182 mm (S) X 235 mm (W)

Windows 2000 / XP / Vista 32 / Vista 64

Zasilanie wentylatora procesora (z funkcją Smart Fan)

Zasilanie wentylatora systemowego

Każde złącze obs ługuje 2 porty USB na panelu

przednim

Biostar zastrzega sobie prawo dodawania lub

odwoływ ania obsług i dowo lneg o s ys t emu

operacyjnego b ez powiado mienia.

G41-M7

39

Motherboard Manual

RUSSIAN

CPU

(центральн

ый

процессор)

FSB 800 / 1066 / 1333 МГц

Набо р

микросхем

Основная

память

Графика GMA X4500

Super I/O

IDE

SATA

Локальна я

сеть

Звуко вая

поддержка

жестког о

диска

Слоты

Встроенны

й разъём

LGA 775

Процессор Intel Core2Duo / Core2Quad /

Pent iu m Dua l-Co re / C eleron Du al-Co re /

Celeron 4xx

(Макси мальн ый ватт: 95W)

Intel G41

Int e l ICH7

Слоты DDR2 DIMM x 2

Каждый модуль DIMM поддерживает

256 МБ / 512МБ / 1ГБ / 2ГБ DDR2

Максимальная ёмкость памяти 4ГБ

ITE 8718F

Обеспечивает наиболее используемые

действующие фун кцио наль ны е

возможно сти Super I/O.

Интерфейс с ни зким количес твом

выводов

Встроенное устройство управления

встроенными интерфейсами устройс тв

Встроенное последовательно е

устройс тво управления ATA

Realtek RTL 8102EL

ALC662

Слот PCI x2

Слот PCI Express x16 x1

Разъ ём НГМД x1

Разъ ём Порт подключения

принтера x1

Последо ват ельный порт x1

СПЕЦ

Поддержка технологий Hyper-Threading / Execute

Disab le Bit / Enhanced Int el SpeedStep® / Int el

Architecture-64 / Extended Memory 64 Technology /

технологии виртуализац ия

Мод ул ь памяти с двухкан альным режимом DDR2

Поддержка DDR2 800/667

Не поддерживает зарегистрированные модули

DIMM and ECC DIMM

Максимальная совместно использ уемая вид ео

память составляет 256 МБ

Инициативы по охране окружающей среды,

Аппаратный монитор

Регул ят ор скорости вентиля то ра/ монитор

Функция ITE "Smart Guardian" (Интеллектуальная

защит а)

Режим "хозяина" шины Ultra DMA 33 / 66 / 100

Поддержка режима PIO 0~4,

скорость передачи данных до 3.0 гигабит/с.

Соответствие спецификации SATA версия 2.0.

Автоматическо е согласование 10 / 100 Мб /с

Частичная / полна я дуплексная способность

Звуко вая поддержка H igh- Def inition

5.1канальный звуковой выход

Каждый разъём поддерживает 2 накопителя на

гибких магнитных дисках

Каждый разъём поддерживает 1 По рт подключения

принтера

40

Задняя

панель

средств

ввода-выв

ода

Разм ер

панели

Поддержка

OS

G41-M7

СПЕЦ

Разъ ём IDE x 1

Разъ ём SATA x4 Каждый разъём поддерживает 1 устройс тво SATA

Разъ ём на лицевой панели x1 Поддержка устройс тв на лицевой панели

Входной звуковой разъём x1 Поддержка звуко вых функций на лицевой панели

Контактирующее приспособление

вентил ятор а центрального процессора

x1

Контактирующее приспособление

вентил ятор а системы x1

Открытое контактирующее

приспособление CMOS x1

USB- разъём x2

Разъ ем питания (24 вы вод) x1

Разъ ем питания (4 вывод) x1

Клавиатура PS/2 x1

Мышь PS/2 x1

Пор т VGA x1

Пор т LAN x1

USB- порт x4

Гнездо для подключени я

наушников x3

182 мм (Ш) X 235 мм (В)

Windows 2000 / XP / Vista 32 / Vista 64

Каждый разъём поддерживает 2 встроенных

интерфейса накопителей

Источник пит ания для вентил ятора центрального

процессора (с функц ией интеллектуального

вентил ятор а)

Источник пит ания для вентил ятора системы

Каждый разъём поддерживает 2 USB-порта на

лицевой панели

Biostar сохраняет за собой право добавлять или

удаля ть средства обеспечения для OS с или без

предварительного уведом ле ния .

41

Motherboard Manual

ARABIC

تﺎﻔﺻاﻮﻤﻟا

ﺪﺗ تﺎﻴﻨﻘﺗ ﻢﻋ Hyper-Threading / Execute Disable Bit /

Enhanced Inte l SpeedStep® / Int e l Architecture-64 /

Extended Memory 64 Technology / Virtualization

Technology

ةﺮآاذ ةﺪﺣوDDR2 ﻘﻟا ﺔﺝودﺰﻣةﺎﻨ

عﻮﻥ ﻦﻣ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR2 تﺎﻌﺳ 667/800ﺖیﺎﺑ ﺎﺠﻴﻣ

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻDIMM ﻊﻣ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠﺗو ECC

ﺔآﺮﺘﺸﻤﻟا ﻮیﺪﻴﻔﻟا ةﺮآاﺬﻟ ﺔﻌﺳ ﻰﺼﻗأ256ﺖیﺎﺑ ﺎﺠﻴﻣ

ةﺰﻬﺝﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻣ

ﺔﺣوﺮﻤﻟا ﺔﻋﺮﺳ ﻲﻓ ﺐﻗاﺮﻣ

ﺔﻔﻴﻇو"S mart Guard ian" ﻦﻣ IT E

LGA 775

تﺎﺠﻟﺎﻌﻣIntel Core2Duo / Core2Quad /

Pent iu m Dua l-Co re / C eleron Du al-Co re /

Celeron 4xx ﺑ ددﺮﺘ ی ﻰﻟإ ﻞﺼ

(طاو ىﻮﺼﻗ: 95و)

ددﺮﺗ 800 / 1066 / 1333 ﺰﺗﺮه ﺎﺠﻴﻣ

Intel G41

Int e l ICH7

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM عﻮﻥ ﻦﻣ ةﺮآاذ ﻢﻋﺪﺗ DDR2 ﺔﻌﺳ

256/512 و ﺖیﺎﺑ ﺎﺠﻴﻣ 2و ﺖیﺎﺑ 1 ﺎﺠﻴﺝﺖیﺎﺑ

ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ4 ﺖیﺎﺑ ﺎﺠﻴﺝ

GMA X4500

وﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳ:

ITE 8718F

ﺔﻔﻴﻇ و ﺮﻓﻮﺗSuper I/O ًﺎ ﻣ ا ﺪ ﺨ ﺘﺳا ﺮﺜآﻷا .

ﺗﻢﻋﺪ ﺔﻴﻨﻘﺗ Low Pi n Count Interface

ةﺪﺣو ﺔﺠﻟﺎﻌﻤﻟا

ﺔیﺰآﺮﻤﻟا

ﻞﻗﺎﻨﻟا ﻲﻣﺎﻣﻷا ﻲﺒﻥﺎﺠﻟا

ﺔﻋﻮﻤﺠﻣ ﺢﺋاﺮﺸﻟا

ﺔﺤﺘﻓDDR2 DIM M دﺪﻋ2

ةﺮآاﺬﻟا ﺔﻴﺴﻴﺋﺮﻟا

ﺔﻗﺎﻄﺑ تﺎﻣﻮﺳﺮﻟا

Super I/O

42

ﺔﻴﻨﻘ ﺘﺑ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100ﻲﺴﻴﺋر ﻊﺿو

ﻊﺿو ﻢﻋدPIO Mode 0~4

ﻞﻘﻥ تﺎﻥﺎﻴﺒﻟا تﺎﻋﺮﺴﺑ ﻞﺼﺗ ﻰﻟإ 3.0 ﺖﺑﺎﺠﻴﺝ/ﺔﻴﻥﺎﺙ.

ﺔﻘﺑﺎﻄﻣ تﺎﻔﺹاﻮﻤﻟ SATA راﺪﺹﻹا 2.0.

ﻲﺋﺎﻘﻠﺗ ضو ﺎﻔﺗ10/100 ﺖیﺎﺑ ﺎﺠﻴﻣ /ﺔﻴﻥﺎﺙ

ﻞﻣﺎﻜﻟا جودﺰﻤﻟا ﻞﻘﻨﻟا ﺔﻴﻥﺎﻜﻣإ/ﻲﻔﺼﻨﻟا

5.1 تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ

ﻢﻋﺪﺗ ﻦﻣ ﻒیﺮﻌﺘﻟا ﻲﻟ ﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺗ

ﺔﺤﺘﻓPCI دﺪﻋ2

ﺔﺤﺘﻓx16 PCI Express دﺪﻋ1

ﻢﻜﺤﺘﻣIDE ﻞﻣﺎﻜﺘﻣ

ﻢﻜﺤﺘﻣ Serial ATA ﻞﻣﺎﻜﺘﻣ

Realtek RTL 8102EL

ALC662

ﺬﻔﻨﻣ ID E

SATA

ﺔﻜﺒﺷ ﺔﻴﻠﺧاد

ﻢﻋد تﻮﺼﻝا ﻲﻝﺎﻋ

ﻒیﺮﻌﺘﻝا

تﺎﺤﺘﻔﻟا

تﺎﻔﺻاﻮﻤﻟا

G41-M7

ﺔﻥﺮﻤﻟا صاﺮﻗﻸﻟ ﻦﻴآ ﺮﺤﻣ ﻢﻋﺪی

ﺔﻌﺑﺎﻃ ﺬﻔﻨﻣ دﺪﻋ1

ﻲﻠﺴﻠﺴﺗ ﺬﻔ ﻨﻣ دﺪﻋ1

ی ةﺰﻬﺝأ ﻦﻣ ﻦﻴﻨﺙا ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪIDE

ةﺰﻬﺝأ ﻦﻣ ﺪﺣاو ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪیSATA

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا تاﺰﻴﻬﺠﺗ ﻢﻋﺪی

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟ ﺎﺑ تﻮﺼﻟا ﺔﻔﻴﻇو ﻢﻋﺪی

و ﻊﻣ ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺘﻟ ﺔﻔﻴﻇ Smart Fan

مﺎﻈﻨﻟا ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺘﻟ

ﺢﺴ ﻣ ﺔﻠﺹوCMOS دﺪﻋ1

ﻲﺘﺤﺘﻓ ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪیUSBﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟﺎﺑ

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻣ)24سﻮ ﺑد( دﺪﻋ1

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻣ)4ﺲﻴﺑﺎﺑد( دﺪﻋ1

ﺔﻥﺮﻣ صاﺮﻗأ كﺮﺤﻣ ﺬﻔﻨﻣ دﺪﻋ1

ﺬﻔﻨﻣID E دﺪﻋ1

ﺬﻔﻨﻣSATA دﺪﻋ4

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮ ﻠﻟا ﺬﻔﻨﻣ دﺪﻋ1

ﺬﻓﺎﻨﻤﻝا ﻰﻠﻋ ﺢﻄﺳ

ﻲﻣﺎﻣﻷا تﻮﺼﻟا ﺬﻔﻨﻣ دﺪﻋ1

ﺔیﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻣ ﺔﻠﺹو دﺪﻋ1

ﺔﺣﻮﻠﻝا

مﺎﻈﻨﻟا ﺔﺣوﺮﻣ ﺔﻠﺹو دﺪﻋ1

ﺬﻔﻨﻣUSB دﺪﻋ2

ﺢﻴﺗﺎﻔﻣ ﺔﺣﻮﻟPS/2 دﺪﻋ1

سوﺎﻣ PS/2 دﺪﻋ1

ﺬﻔﻨﻣVGA دﺪﻋ1

ﺔﻴﻠﺤﻣ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻣ دﺪﻋ1

ﺬﻓﺎﻨﻣ ﻞﺧد/جﺮﺧ

ﺔﺣﻮﻠﻝا ﺔﻴﻔﻠﺨﻝا

ﺬﻓﺎﻨﻣUS B دﺪﻋ4

تﻮﺹ ﺲﺒﻘﻣ دﺪﻋ3

ﻆﻔﺘﺤﺕ Biostar ﺎﻬﻘﺤﺏ ﻲﻓ ﺔﻓﺎﺿإ وأ ﺔﻝازإ ﻢﻋﺪﻝا يﻷ مﺎﻈﻥ ﺸﺕﻞﻴﻐ رﺎﻄﺧﺈﺏ وأ نوﺪﺏ

182 ﻢﻣ)ضﺮﻋ (X 235 ﻢﻣ)عﺎﻔﺗرا( ﻢﺠﺣ ﺔﺣﻮﻠﻝا

Windows 2000 / XP / Vista 32 / Vista 64

رﺎﻄﺧإ.

ﻢﻋد ﺔﻤ ﻈﻥأ ﻞﻴﻐﺸﺘﻝا

43

Motherboard Manual

JAPANESE

仕様

LGA 775

Intel Core2Duo / Core2Quad /

CPU

FSB 800 / 1066 / 1333 MHz

チップセット

メインメモリ

グラフィック

ス

Super I/O

Pent iu m Dua l-Co re / C eleron Du al-Co re /

Celeron 4xx processor

(最高のワット: 95W )

Intel G41

Int e l ICH7

DDR2 DIMMスロット x 2

各DIMMは 256MB / 512MB / 1GB / 2GB

DDR2をサポート

最大メモリ容量4GB

GMA X4500 最大の共有ビデオメモリは256MBです

ITE 8718F

もっとも一般に使用されるレガシーSuper I/O

機能を採用しています。

Hyper-Threading / Execute Disab le Bit / Enhanced Inte l

SpeedSt ep® / Intel Architecture-64 / Extended

Memory 64 Technology / V irtualization Technologyをサ

ポートします

デュアル チャンネルモードDDR2メモリモジュール

DDR2 800/667をサポート

登録済みDIMMとECC DIMMはサポートされません

環境コントロールイニシアチブ、

H/Wモニター

ファン速度コントローラ/ モニター

低ピンカウントインターフェイス

IDE 統合ID Eコントローラ

SATA 統合シリアルATA コントローラ

LAN Realtek RTL 8102EL

HDオーディ

ALC662

オのサポート

44

ITE の「スマートガーディアン」機能

Ultra DMA 33 / 66 / 100バスマスタモード

PIO Mode 0~4のサポート、

最高3.0 Gb/秒のデータ転送速度

SATAバージョン2.0仕様に準拠。

10 / 100 Mb/秒のオートネゴシエーション

半/全二重機能

ハイデフィニションオーディオのサポート

5.1 チャンネルオーディオアウト

仕様

G41-M7

スロット

オンボードコ

ネクタ

PCIスロット x2

PCI Express x16スロット x1

フロッピーコネクタ x1 各コネクタは2つのフロッピードライブをサポートします

プリンタポートコネクタ x1 各コネクタは1つのプリンタポートをサポートします

シリアルポート x1

IDE コネクタ x1 各コネクタは2つのIDE デバイスをサポートします

SATAコネクタ x4 各コネクタは1つのSATAデバイスをサポートします

フロントパネルコネクタ x1 フロントパネル機能をサポートします

フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします

CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載)

システムファンヘッダ x1 システムファン電源装置

CMOSクリアヘッダ x1

各コネクタは2つのフロントパネルUSBポートをサポートし

USBコネクタ x2

ます

電源コネクタ(24 ピン) x1

電源コネクタ(4ピン) x1

PS/2キーボード x1

背面パネル

I/O

ボードサイズ

OSサポート

PS/2マウス x1

VGAポート x1

LANポート x1

USBポート x4

オーディオジャック x3

182 mm (幅) X 235 mm (高さ)

Biostarは事前のサポートなしにOSサポートを追加または削

Windows 2000 / XP / Vista 32 / Vista 64

除する権利を留保します。

2009/02/06

45