Binatone Vantage 6020 Quad, Vantage 6020 Twin, Vantage 6020 Triple User Manual
1 2 43
7 85 6 109
11 12 13 14 15 16
Rem ote op era tion
Using a tone-dialling phone, dial your home number
You can also use the codes on the other side of this card
While your outgoing message is playing, press
Key in your remote security code
The default code is 0000. For details of how to set a new code,
see the User Guide 8.5.9.1 on page 30.
1
2
3
4
Note: <*> key must be entered while the OGM is still playing, and the 4-digit
consecutively, the line will be release
Note: If your answering machine is switched off, the phone will enter into
the remote access mode after 14 rings.
You can then enter the 4-digit remote access PIN
(Default Remote Access PIN is 0000) to activate the remote access feature.
The
PIN should follow without any delays. If the 4-digit Remote Access
PIN is entered incorrectly three times
automatically.
d
Electrical power
TECHNICAL DETAILS
Standard
Frequency range
Channel bandwidth
Operating range
Operating time
Temperature range
Digital Enhanc ed Cord less
Telecom munica tion (DECT )
1.88 to 1 .9G Hz
1.728 MH z
Up to 300 mou tdoors ;
Standby : 100 ho urs,
Talking :10 hours
Battery charge time:1 5 hours
Operati ng 0 C to 40 C ,
Storage -20 C to 60 C
(bandwi dth = 20 MHz )
Up to 50 mind oors
Caution
Risk of explosion if battery is replaced by an incorrect type
Dispose of used batteries according to the instructions.
The port (connected to the mains power supply) is a SELV port with
The port (connected to the telephone line ) is a TNV port with
respect to EN41003.
CLEANING AND CARE
Do not clean any part of your phone system with benzene, thinners or other
solvent chemicals as this may cause permanent damage which is not covered
by the Guarantee.
When necessary, clean it with a damp cloth.
Keep your hot, humid conditions
or
strong sunlight,and don't let it get wet.
Every effort has been made to ensure high standards of reliability for your
consult your supplier or the Helpline.
do
not try to repair it yourself, but
phone system away from
Port specification
respect to EN41003 .
phone system. However, if something does go wrong, please
Base unit:
VTech – VT04EUK06045 / VT04EEU06045
input 100-240VAC 50/60Hz 150mA, output 6VDC 450mA
Tenpao:S003IB0600045/S003IV0600045
input 100-240VAC 50/60Hz 150mA, output 6VDC 450mA
Charger unit:
VTech – VT04EUK06045 / VT04EEU06045
input 100-240VAC 50/60Hz 150mA, output 6VDC 450mA
Tenpao:S003IB0600045/S003IV0600045
input 100-240VAC 50/60Hz 150mA, output 6VDC 450mA
Battery information as below:
CORUN-Ni-MH AAAJ400, Type Ni-MH (Rechargeable battery)
Voltage Rating 400mAh, 2 X 1.2V AAA Size
GPI-VT40AAAHC, Type Ni-MH (Rechargeable battery)
Voltage Rating 400mAh, 2 X 1.2V AAA Size
Coslight-LH040-3AH45, Type Ni-MH (Rechargeable battery)
Voltage Rating 400mAh, 2 X 1.2V AAA Size
Package contents
The package contains the following items:
• 1 Handset
• 1 Base station
• 1 Mains power adapter
• 1 Telephone line cord
• 2 AAA rechargeable batteries
• 1 User manual
Note: If you have a Twin, Triple or Quad system, you will also have the requisite
extra handset(s) and batteries, and a charger pod for each extra handset.
Connection and conditions for use:
You can connect your phone to a direct exchange line (DEL) on a local
exchange with its own phone number; to an extension socket connected to a
DEL; or to an extension on an approved compatible PBX. Do not connect as an
extension to a payphone.
The ringer equivalence numbers (REN) of all equipment (phones, fax machines,
modems, etc.) connected to an exchange line must not add up to more than 4,
otherwise one or more of them may not ring and/or answer calls correctly. The
phone has a REN of 1, and most other telephones have a REN of 1 unless
marked otherwise.
Handset - Base Connection
1) When purchased, all handsets are already registered to the base unit and
should link to it when they are all powered up.
2) To use your cordless handset and base unit together, you must be able to
establish a radio link between them. The signal between the handset and
the base is in accordance with the normal standards for a DECT phone:
Maximum range up to 300 metres outdoors or 50 metres indoors. Be aware
that:
> Any large metal object, such as a refrigerator, mirror or ling cabinet, between
the handset and the base unit may block the radio signal.
> Other solid structures, like walls, may reduce the signal strength.
> Other electrical equipment may cause interference and/or affect the range.
3) Do not place close to another telephone, a TV or audio equipment - it may
cause interference.
4) Out of Range warning. If you hear a warning tone during a call, and/or the
sound in the earpiece becomes faint or distorted, you may be going out of range
of the base unit, so move nearer to the base unit within 20 seconds, otherwise
the call may be cut off.
3.2 Base Station with Telephone Answering Machine( TAM) Control
3.3 Display icons and Symbols
The LCD display gives you information on the current status of the telephone.
Press to decrease the
playback Volume, or the base
ringer volume during incoming
ringing.
DELETE
Press once to delete
the message during playback
From idle: Press and hold
to delete all the old messages.
SKIP BACKWARD
Press to repeat playing the
current message from the
beginning.
Press twice to skip back to the
previous message.
FIND
Press to find your handset.
It will ring for approximately 60
seconds.
Press to increase the playback
Volume, or the base ringer
volume during incoming
ringing.
PLAY/STOP
Press to play the messages.
Press to stop messages
playing.
SKIP BACKWARD
Press to skip the current
message and play the next
message.
TAM ON/OFF
Press to turn on the answering
machine.
Press again to turn off the
answering machine.
TAM indicator light.
- On when TAM is ON
- Flashes if new TAM
messages are recorded,
or when TAM is being
used.
Steady when the handset is in range of the base. Flashes when out
of range of the base or not registered to the base.
Steady when an intercom call is in progress.
Flashes when there is an incoming internal call.
Indicates a call is in progress on that handset.
Indicates that your answering machine (TAM) is on and ashes
when there is a new message.
Indicates that the handset ringer is switched off.
Steady when an alarm is set. Flashes when the alarm is sounding.
Indicates that the keypad is locked.
Indicates when you have a new Voice Mail message.
(This is a Caller Display service and is not usually available from
UK network providers.)
Indicates when the battery is fully charged.
Whole icon ashes when the battery is charging.
Internal block icon ashes when the battery is in nal charging stage.
Indicates when the battery needs charging.
Indicates when the battery needs charging.
Indicates when there are more characters or numbers in front of
those being displayed.
Indicates when there are more characters or numbers after those
being displayed.
LEFT SOFT KEY function. Press to access the main menu.
LEFT SOFT KEY function. Press to conrm the current selection.
Indicates a new TAM message is playing or a new Call List entry is
being displayed.
Indicates you can scroll up / down the menu items / Phonebook list /
Redial list / Call List
(INT)
RIGHT SOFT KEY function. Press to start an intercom call.
(BACK)
RIGHT SOFT KEY function. Press to go back to the previous menu
level or cancel the current action.
RIGHT SOFT KEY function. Press to clear a character, stop the
alarm, or mute/unmute the microphone during a call.
4.3 End a Call
During a call press <TALK OFF> to end the call. OR
Put the handset on the base station or charger to end the call.
4.4 Adjust the Earpiece Volume
There are 5 levels (VOLUME 1 to VOLUME 5) to choose fromfor each of the
earpiece.
During a call:
Press <UP/DOWN> to select volume 1-5. The current setting is shown. When
you end the call, the setting will remain at the last selected level.
4.5 Mute a Call
You can talk to someone nearby without letting the caller hear you during a call.
During a call:
Press <C/MUTE> to mute the microphone and “MUTED ” will display on the LCD.
Your caller cannot hear you. Press <C/MUTE> again to unmute the microphone.
4.6 Turn off the Handset Ringer
In idle, press and hold # /
to turn off the handset ringer. The “ ” icon is
displayed on the LCD.
Note: The display will still ash the Call icon and show CALL or the Caller
Display number, when there is an incoming call, even if the ringer is turned off
To turn the ringer back on, press and hold # / again.
4.7 Turn on the Keypad Lock
You can lock the keypad so that it cannot be used accidentally while carrying it
around. In idle, press and hold < * /
> to turn on the keypad lock, and the
“
” icon i s displayed on the LCD.
Note: You can still use <TALK ON> to answer a call when the handset is ringing.
To turn the keypad lock off, press and hold < * / > again.
4.8 Redial the last number
You can redial any of the 5 last numbers called. If you have stored a name
in the phonebook to go with the number, the name will be displayed instead.
The most recent last number will display at the top of the redial list.
4.8.1 Redial a Number from the Redial List
1. Press <DOWN> (Redial) to access the redial list.
Note: If the redial list entry shows a name, press # /
to view the number of this entry.
2. Press <UP/DOWN> to browse the redial list.
3. Press <TALK ON> to dial to the selected redial number.
Note: If there are no numbers in the redial list, the display shows “EMPTY ”.
4.8.2 Store a Redial Number into the Phonebook
1. Follow Steps 1 and 2 in section 4.8.1.
2. Press <MENU/OK> to show ADD TO PB.
3. Press <MENU/OK> and then enter the name you want to use in the
phonebook.
4. Press <MENU/OK> and then modify the number, if necessary.
5. Press <MENU/OK> to show <MELODY 1>.
6. Press <UP/DOWN> to browse the ringtone list. The respective ringtones
play while browsing the list. (Note: the selected melody will
only play when you receive a call if you subscribe to Caller Display and the
incoming number matches the stored number.)
7. Press <MENU/OK> to conrm, and the entry will be stored.
4.8.3 Delete a Redial Number
1. Follow Steps 1 and 2 in section 4.8.1.
2. Press <MENU/OK> and <UP/DOWN> to select DELETE.
3. Press <MENU/OK> to conrm, and the entry will be deleted.
4.8.4 Delete all Redial List entries
1. Follow Steps 1 and 2 in section 4.8.1.
2. Press <MENU/OK> and <UP/DOWN> to select DELETE ALL
3. Press <MENU/OK> to display CONFIRM?.
4. Press <MENU/OK> to conrm. All entries will be deleted and the display
will show EMPTY.
4.9 Find the Handset
You can locate the handset by pressing <FIND> on the base station. All the
handsets registered to the base will produce the paging tone and show
“PAGING” on the display for 60 seconds. You can stop the paging by pressing
<TALKON>/ <TALK OFF> /<C/MUTE> on any handset or <FIND> on the base
again.
Note: If there is an incoming call during paging, the phone will ring with the
incoming call instead of paging.
4.10 Make an Internal Call (Multi - handset versions only)
This feature is only applicable when there are at least two registered handsets.
It allows you to make internal calls, transfer external calls from one handset to
another handset and make conference calls. If the called handset is not
answered within 60 seconds, the called handset will stop ringing and the calling
handset will return to standby mode.
Note: If only one handset is registered to the base station, when <C/MUTE>
is pressed, it will display “NOT POSSIBLE”.
4.10.1 Intercom Another Handset
1. In idle mode, press <C/MUTE> and all the other registered handset
numbers will display, along with a “9”.
2. Enter the number of the handset that you want to call, or press the < 9 >
key to call all handsets.
3. The called handset rings and <TALK ON> must be pressed on that handset
to establish the intercom call.
Note: If only two handsets are registered to the base station, pressing
<C/MUTE> will call the other handset immediately.
Note: If there is an external call while you are on an intercom call, you’ll hear
warning beeps, and you have to end the intercom call, before you can
answer the external call.
4.10.2 Call All Handsets
1. In idle mode, press <C/MUTE> and the registered handsets will display.
2. Press the < 9 > key to ring to all registered handsets
4.10.3 Transfer an External Call to another handset
During an external call:
1. Press <MENU/OK> to show INTERCOM.
2. Press <MENU/OK> to show all the other registered handset numbers, plus “9”.
Enter the number for the handset you want to transfer the call to.
3. The external call is put on hold automatically and the called handset rings.
4. Press <TALK ON> on the called handset to establish an internal call.
5. Press <TALK OFF> on the calling handset or put the calling handset on the
charging cradle to end the current call with the external party.
6. The external call is transferred to the called handset.
Note: If the other handset has not answered the intercom call, you can stop
the intercom and return to the external call by pressing <TALK OFF>
4.1 .4 Make a 3-way Conference Call
The conference call feature allows one external call to be shared with two
handsets (in intercom).
The three parties can share the conversation and no additional network
subscription is required.
During an external call:
1. Follow Steps 1 to 4 in section 4.10.3.
2. Press and hold < * /
> on the calling handset to establish the conference call.
Either handset can exit the conference by pressing <TALK OFF>, leaving
the other handset still connected to the external call.
5 PRIVATE PHONEBOOK
Each handset can store up to 20 private phonebook entries with names and
numbers. Each phonebook entry can have a maximum of 20 digits for the
phone number and 12 characters for the name. You can also select different
ringtones for your phonebook entries. (Note: the different ringtones only play if
you subscribe to Caller Display and the incoming number matches the stored
number.) Phonebook entries are stored alphabetically by name.
5.1 Add a New Phonebook Entry
In idle:
1. Press <PHONEBOOK> to access the phonebook. OR
Press <MENU/OK> and <UP/DOWN> to select PHONEBOOK and then
press <MENU/OK> to access the phonebook.
2. Press <MENU/OK> to show ADD.
3. Press <MENU/OK> and then enter the name.
4. Press <MENU/OK> and then enter the number.
5. Press <MENU/OK> and <UP/DOWN> to select the desired ringtone for
your phonebook entry.
6. Press <MENU/OK> to store the phonebook entry.
5.2 Search for a Phonebook Entry
In idle:
1. Press <PHONEBOOK> to access the phonebook.
2. Enter the rst letter of the name using the alphanumeric keys (e.g. if it
begins with C, press the 2 key three times), and then <UP/DOWN>
to scroll to the entry you want.
5.3 View a Phonebook Entry
In idle:
1. Press <PHONEBOOK> to access the phonebook.
2. Press <UP/DOWN> to select the desired phonebook entry.
3. Press <MENU/OK> and <UP/DOWN> to select VIEW.
4. Press <MENU/OK> and <UP/DOWN> to review the name, number and
ringtone of the selected phonebook entry.
Note: If the number is more than 12 digits, press <MENU/OK> or <C/MUTE>
to view the remaining digits.
5.4 Edit a Phonebook Entry
In idle:
1. Press <PHONEBOOK> to access the phonebook.
2. Press <UP/DOWN> to select the desired phonebook entry.
3. Press <MENU/OK> and <UP/DOWN> to select EDIT.
4. Press <MENU/OK> to display the current name.
5. Edit the name and press <MENU/OK>.
6. Edit the number and press <MENU/OK>.
7. Press <UP/DOWN> to select the ringtone and press <MENU/OK> to
conrm.
5.5 Delete a Phonebook Entry
In idle:
1. Press <PHONEBOOK> to access the phonebook.
2. Press <UP/DOWN> to select the desired phonebook entry.
3. Press <MENU/OK> and <UP/DOWN> to select DELETE.
4. Press <MENU/OK> to conrm, and the entry will be deleted.
5.6 Delete all Phonebook entries
1. Press <PHONEBOOK> to access the phonebook.
2. Press <MENU/OK> and <UP/DOWN> to select DELETE ALL.
3. Press <MENU/OK> to display CONFIRM?.
4. Press <MENU/OK> to conrm. All entries will be deleted and the display
will show EMPTY.
5.7 Check the Phonebook Usage
You can check how many phonebook entries are stored in your handset and
how many phonebook entries are available for you to store in the phonebook.
1. Press <PHONEBOOK> to access the phonebook.
2. Press <MENU/OK> and <UP/DOWN> to select PB STATUS.
3. Press <MENU/OK> to display how much of the phonebook is being used
for example 14/50 USED means 14 entries are stored out of the
total 50 available spaces.
3 GETTING TO KNOW YOUR PHONE
3.1 Handset Overview
1 UP (
)
From idle: access the Call List
In lists: move up the options
During calls / ringing: increase the
volume.
2 LEFT SOFT KEY (
)
MENU/OK
Use with icons on display above, to
open menu and conrm options.
3 TALK ON (
)
Make or answer calls
4 DOWN (
)
In lists: move down the options
During calls / ringing: decrease the
volume.
6 RIGHT SOFT KEY (
)
C/MUTE
Use with icons on display above, to
clear characters, go back to previous
menu, mute the microphone or make
an intercom call.
7 TALK OFF (
)
End a call or return to previous menu.
Press and hold to turn the handset
on / off.
8 R - RECALL (
)
also called Flash
Sends a recall (R) signal, used for
some PBX / Calling Features.
9 PHONEBOOK (
)
Press to open the Phonebook list.
1 IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always
be followed to reduce the risk of fire, electric shock and injury, including the
following:
1) Read and understand all the instructions.
2) Follow all warnings and instructions marked on the product.
3) Unplug this product from the wall outlet before cleaning. Do not use liqui d
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4) Keep y our Vantage 6020 awa y fr om ho t, h umid condi tions or strong
sunlight, and don’t let it get wet or use this product near water (for example,
near a bath tub, kitchen sink, swimming pool).
5) Do not overload wall outlets and extension cords as this can result in the
risk of fire or electric shock.
6) Unplug this produc t from the wall outlet and refer servicing to our Repa ir
Centre under the following conditions:
• When the power supply cord or plug is damaged or frayed.
• If the product does not operate normally by following the operating
instructions.
• If the product has been dropped and the cabinet has been damaged.
• If the product exhibits a distinct change in performance.
7) NEVER use your Vantage 6020 outdoors during a thunderstorm - unplug
the base from the te lephone line and the mains so cket whe n there are
storms in your area. Dama ge caused by li ghtning is not covered by the
guarantee.
8) Do not use the telephone to report a gas leak in the vicinity of the leak.
9) Use only the supplied NiMH (Nickel Metal Hydride) batteries! The operation
period s for the han dsets are only appl icable with the def ault batter y
capacities.
10) The use of other battery types or non-rechargeable batteries/primary cells
can be dangerous. These may cause interference and/or damage to the unit
or surroundings. The manufacturer will not be held liable for damage arising
from such non-compliance.
11) Do not use third party char ging bays. Damage may be c aused to th e
batteries.
12) Please ensure the batteries are inserted in the correct polarity.
13) Dispose of batteries safely. Do not immerse them in water, burn them, or put
them where they could get punctured.
2 INSTALLING YOUR PHONE
2.1 Connecting the base station
1) Plug the power supply and line cord
into the base station.
2) Plug the power adapter into a 100-240V
50/60Hz mains socket, and the line cord into
your telephone line socket.
3) Always use the cables provided in the box.
Warning: Use only the provided power
adapter, as others may cause a hazard.
Warning: Install the base unit in a position where the mains adapter plug will
reach an easily accessible mains socket. Never try to lengthen the mains
power cable.
Note: The base unit needs mains power for normal operation, not just for
charging the handset batteries.
2.2 Installing and charging the batteries
1) Place the 2 supplied batteries into the battery compartment with the polarity
markings as shown. Use only the NiMH
rechargeable battery type provided.
2) Position the battery compartment cover over
the batteries and slide up to click into place.
3) Put the handset on the base and charge for
15 hours before using the handset for the first
time. The handset will give a beep when it is
properly placed on the base or charger.
Note: To charge a handset you can put it face-up
or face-down on the base or charger.
If you have a Broadband line
If you connect your telephone to a line with
a broadband connection, you will need to
insert a micro-filter between the telephone
and the telephone line, otherwise you may get
interference between the telephone and the
broadband, which could cause problems.
In a home with broadband, every telephone
must have a micro-filter connected, not just the
one at the telephone point that your modem is connected to.
If you need more broadband micro-filters, contact your broadband supplier.
3.5 Text and Digit Entry Table
The following table shows you where each letter and punctuation character can
be found, by using repeated presses of the alphanumeric keypad. This will be
helpful when storing a name in the phonebook and renaming your handset.
In editing mode, a cursor is displayed to indicate the current text entry position.
It is positioned at the right of the last character entered.
Writing Tips:
1. Once a character is selected, the cursor will move to the next position after
a short pause.
2. You can move the cursor within the text with the <UP/DOWN> keys to
amend the text entry.
3. Press <C/MUTE> to delete the last character.
4. Press and hold <C/MUTE> to delete the entire text string.
3.5.1 English Character Set
Alphanumeric Editing
(For phonebook name editing and renaming handset)
Number Editing (For phone
number editing, date/time editing)
Key Press1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th
1 space - 1 1
2 A B C 2 2
3 D E F 3 3
4 G H I 4 4
5 J K L 5 5
6 M N O 6 6
7 P Q R S 7 7
8 T U V 8 8
9 W X Y Z 9 9
0 0 0, or P (Pause) if press and hold
* * ? / \ ( ) *
# O,, - & #
"Some o ther ch aracters are a vailable with some o f the alternat ive han dset
language options (see 7.3.5)."
4 USING YOUR PHONE
4.1 Make a Call
4.1.1 Preparatory Dialling
Enter the phone number and press <TALK ON> to connect to the line and
dial the number. When entering the number, if you make a mistake, press
<C/MUTE> to delete digits.
4.1.2 Direct Dialling
Press <TALK ON> to connect to the line and then enter the phone number.
(Note: if you enter a wrong digit you cannot correct it with the <C/MUTE> key.)
4.1.3 Call from the phonebook
Press <PHONEBOOK> to access the phonebook and press <UP/DOWN> to
select the desired phonebook entry.
Press <TALK ON> to dial out the selected phonebook entry.
Note: The alphanumeric keys provide a short-cut to nd entries beginning with
the corresponding letters.
4.1.4 Call from the Call List (only available with Caller Display)
Press <UP> to access the Call List and press <UP/DOWN> to select the
desired Call List entry.
Press <TALK ON> to dial out the selected Call List entry.
Note: You can also access the Call List by pressing <MENU/OK> twice.
4.1.5 Call from the redial list
Press <REDIAL> to access the redial list and press <UP/DOWN> to select the
desired redial number.
Press <TALK ON> to dial out the selected redial number.
4.1.6 Call timer
Your handset automatically times the duration of every call.
The call timer is displayed as soon as you answer a call or 15 seconds after
dialling and remains on the screen for 5 seconds after the end of the call.
It is shown in hours, minutes and seconds format (HH:MM:SS).
4.2 Answer a Call
If the handset is not on the charging cradle:
When the phone rings, press <TALK ON> to answer a call.
Note: If AUTO ANSWER is set to ON, then lifting the handset off the base or
charger will answer the call automatically, and no buttons need to be
pressed.
3.4 Text and Digit Entry Table
The following table shows you where each letter and punctuation character can
be found, by using repeated presses of the alphanumeric keypad. This will be
helpful when storing a name in the phonebook and renaming your handset.
In editing mode, a cursor is displayed to indicate the current text entry position.
It is positioned at the right of the last character entered.
CONTENTS
1 IMPORTANT SAFETY INSTRUCTIONS ........................................................................3
2 INSTALLING YOUR PHONE ..........................................................................................5
2.1 Connecting the base station ........................................................................................5
2.2 Installing and charging the batteries ............................................................................5
3 GETTING TO KNOW YOUR PHONE .............................................................................6
3.1 Handset Overview .......................................................................................................6
3.2 Base Station with Telephone Answering Machine( TAM) Control ................................7
3.3 Display icons and Symbols ..........................................................................................7
3.4 Text and Digit Entry Table ............................................................................................8
3.5 Text and Digit Entry Table ............................................................................................9
3.5.1 English Character Set .............................................................................................. 9
4 USING YOUR PHONE.................................................................................................. 10
4.1 Make a Call ................................................................................................................10
4.1.1 Preparatory Dialling ................................................................................................10
4.1.2 Direct Dialling ......................................................................................................... 10
4.1.3 Call from the phonebook ........................................................................................ 10
4.1.4 Call from the Call List (only available with Caller Display) ..................................... 10
4.1.5 Call from the redial list ............................................................................................10
4.1.6 Call timer ................................................................................................................ 10
4.2 Answer a Call ............................................................................................................ 10
4.3 End a Call ...................................................................................................................11
4.4 Adjust the Earpiece Volume .......................................................................................11
4.5 Mute a Call .................................................................................................................11
4.6 Turn off the Handset Ringer .......................................................................................11
4.7 Turn on the Keypad Lock ............................................................................................11
4.8 Redial the last number ................................................................................................11
4.8.1 Redial a Number from the Redial List .....................................................................11
4.8.2 Store a Redial Number into the Phonebook ...........................................................12
4.8.3 Delete a Redial Number .........................................................................................12
4.8.4 Delete all Redial List entries ...................................................................................12
4.9 Find the Handset .......................................................................................................12
4.10 Make an Internal Call (Multi - handset versions only) ................................................12
4.10.1 Intercom Another Handset .................................................................................... 12
4.10.2 Call All Handsets ....................................................................................................13
4.10.3 Transfer an External Call to another handset .........................................................13
4.10.4 Make a 3-way Conference Call ..............................................................................13
5 PRIVATE PHONEBOOK .............................................................................................. 14
5.1 Add a New Phonebook Entry .................................................................................... 14
5.2 Search for a Phonebook Entry ................................................................................. 14
5.3 View a Phonebook Entry ...........................................................................................14
5.4 Edit a Phonebook Entry .............................................................................................15
5.5 Delete a Phonebook Entry .........................................................................................15
5.6 Delete all Phonebook entries .....................................................................................15
5.7 Check the Phonebook Usage ....................................................................................15
6 CALLER DISPLAY (NETWORK DEPENDENT) ..........................................................17
6.1 View the Call List .......................................................................................................17
6.2 Store a Call List Number into the Phonebook ........................................................... 17
6.3 Delete an entry in the Call List ...................................................................................17
6.4 Delete all Call list entries ...........................................................................................18
7 PHONE SETTINGS ...................................................................................................... 18
7.1 Date and Time Settings .............................................................................................18
7.1.1 Change the Date Format ........................................................................................18
7.1.2 Change the Time Format ....................................................................................... 18
7.1.3 Set the Time ...........................................................................................................18
7.1.4 Set the Date ........................................................................................................... 19
7.2 Alarm Settings ...........................................................................................................19
7.2.1 Turn on/off the Alarm ..............................................................................................19
7.2.2 Set the Alarm Time (If Alarm time is set to be ON) .................................................19
7.3 Handset Settings .......................................................................................................20
7.3.1 Set the Ringer Melody for Internal Calls ................................................................ 20
7.3.2 Set the Ringer Melody for External Calls ............................................................... 20
7.3.3 Set the Ringer Volume ........................................................................................... 20
7.3.4 Set Alert Tones .......................................................................................................20
7.3.5 Set the Handset Language .................................................................................... 21
7.3.6 Rename the Handset ............................................................................................. 21
7.3.7 Choose the Information to be Displayed in Idle ..................................................... 21
7.3.8 Set the Auto Answer ...............................................................................................21
7.4 Base Settings ............................................................................................................ 21
7.4.1 De-register a Handset ............................................................................................ 21
7.4.2 Change the dial mode(only for Tone/Pulse version) .............................................. 22
7.4.3 Change the Flash (Recall) Time .............................................................................22
7.4.4 Change the System PIN Code ............................................................................... 22
7.5 Registration ............................................................................................................... 23
7.6 Reset Your Phone ......................................................................................................23
8 ANSWERING MACHINE .............................................................................................. 24
8.1 Turn On/Off the Answering Machine ..........................................................................24
8.2 Listen to the Messages in the Answering Machine ....................................................24
8.3 Delete All Messages in the Answering Machine ........................................................25
8.4 Record Memo ............................................................................................................26
8.5 Answering Machine Settings .....................................................................................26
8.5.1 Set the Answer Mode .............................................................................................26
8.5.2 Set the Outgoing Message (OGM) Language ........................................................26
8.5.3 Record Your Own Outgoing Message (OGM) ........................................................
27
8.5.4 Playback and Delete the Outgoing Message (OGM) ............................................. 27
8.5.5 Set the Answer Delay .............................................................................................28
8.5.6 Set the Recording Time of Incoming Message ...................................................... 28
8.5.7 Call Screening ........................................................................................................28
8.5.8 Change the Compression Rate ..............................................................................30
8.5.9 Activate Remote Access ........................................................................................ 30
9 TROUBLESHOOTING ................................................................................................. 32
10 DECLARATION OF CONFORMITY .............................................................................33
11 GUARANTEE AND SERVICE ......................................................................................34
Main
Menu
CALLS LIST PHONEBOOK BS
SETTINGS
HS
SETTINGS
REGISTRATION DEFAULT ANSWER PHONE
Sub
menu
Shows EMPTY
or the first Call
List Entry. Then
<OK> for.
ADD TO PB
DELETE
DELETE ALL
DETAILS
Shows EMPTY or
the first phonebook
Entry.
Then <OK> for:
ADD
PB STATUS
or
ADD
VIEW
EDIT
DELETE
DELETE ALL
PB STATUS
BS RINGER
RING VOLUME
DELETE HS
DIAL MODE
(only for Tone/
Pulse version)
FLASH TIME
CHANGE PIN
ALARM
RING SETUP
TONE
SETUP
LANGUAGE
RENAME HS
HS DISPLAY
AUTO
ANSWER
DATE &
TIME
PIN?---- PIN?---- MSG PLAYBACK
DELETE ALL
MEMO
TAM ON/OFF
TAM SETTING
ANSWER MODE
TAM LANGUAGE
OGM SETTINGS
ANSWER DELAY
RECORD TIME
REMOTE ACC
COMPRESSION
BS SCREENING
CHANGE PIN
Vantage 6020 system
1
2
3
4
5
8
9
6
7
5 REDIAL ( )
From idle: access the Redial List
0
USER GUIDE
Vantage 6020
Vantage 6020 Twin
Vantage 6020 Triple
Vantage 6020 Quad
THIS EQUIPMENT IS NOT DESIGNED FOR MAKING
EMERGENCY TELEPHONE CALLS WHEN THE POWER
FAILS. ALTERNATIVE ARRANGEMENTS SHOULD BE
MADE FOR ACCESS TO DIAL EMERGENCY SERVICES.
Befo re ope ratin g this set ,
plea se rea d thes e instruc tion s care fully .
Digital Cordless Telephone
with Answer Machine
Binatone Helpline (for UK only)
Monday to Friday from 9:00am to 5:00pm
Tel: 0845 345 9677
**Please note that all calls are charged at local rate
Or visit our website: www.binatoneglobal.com
28
Functions
Keys
While message is playing
2
Delete the current message playing.
4
Repeat playing the current message
5
Play the message
Stop the current message playback
6
Skip to play the next message
7
8
Stop the current message playback
9
Turn off the answering machine
from the beginning. Press twice to
skip backward to play the previous
message.
Turn on the answering machine
While message is not playing
Stop the current message playback
29 30 31 32 33 34
19 2217 18 20 21
2523 24 26 27
7.1.4 Set the Date
1. Press <MENU/OK> and <UP/DOWN> to select HS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select DATE & TIME.
3. Press <MENU/OK> and <UP/DOWN> to select SET DATE.
4. Press <MENU/OK> and then enter the date information
in the format you set in Section 7.1.1.
5. Press <MENU/OK> to conrm.
Note: If the date has been set before, the current date will display, otherwise,
“DD-MM-YY ” will display.
7.2 Alarm Settings
You can set an alarm time on this phone. When an alarm is set, the <ALARM>
icon is shown on the handset display.When the alarm time is reached, the
<ALARM> icon and ALARM ON ash on the handset display, and the alarm
tone rings for 45 seconds. You can press any key to disable the alarm. If
the snooze function is activated, the alarm will sound again at the end of the
snooze period of seven minutes. You can also press and hold <TALK OFF>
while the alarm is sounding, to stop the alarm and turn off the snooze function.
Note:
a. A key press will still disable the alarm even if the handset keypad is locked
when the alarm rings.
b. The alarm volume level is the same as the settings of the handset ringer
volume. If the handset ringer is set to VOLUME OFF, the alarm still sounds
at VOLUME 1 level.
c. During an external call or internal call, if an alarm is set and when the alarm time
is reached, the <ALARM> icon and ALARM ON will still ash. An alarm tone
will be emitted from the earpiece to alert the user the alarm time is reached.
Once the user presses any key or presses and holds
<TALK OFF> to disable the alarm, the display will revert to the call duration.
d. During paging or ringing, the alarm will not sound when the alarm time is
reached. However, if the snooze function is enabled and there is no paging
or ringing, the alarm will sound again at the end of the snooze period.
7.2.1 Turn on/off the Alarm
1. Press <MENU/OK> and <UP/DOWN> to select HS SETTINGS.
2. Press <MENU/OK> to show ALARM.
3. Press <MENU/OK> and <UP/DOWN> to select ON/OFF.
4. Press <MENU/OK> to conrm.
Note: If ON is selected, you will be prompted to set the alarm time.
7.2.2 Set the Alarm Time (If Alarm time is set to be ON)
1. Follow Steps 1 to 4 in Section 7.2.1.
2. Enter the alarm time in 24 hour format.
3. Press <MENU/OK> to display SNOOZE.
4. Press <MENU/OK> and <UP/DOWN> to select snooze ON or OFF.
5. Press <MENU/OK> to conrm.
7.3 Handset Settings
7.3.1 Set the Ringer Melody for Internal Calls
1. Press <MENU/OK> and <UP/DOWN> to select HS SETTINGS .
2. Press <MENU/OK> and <UP/DOWN> to select RING SETUP
3. Press <MENU/OK> to show INT RING.
4. Press <MENU/OK> and <UP/DOWN> to select the melody you want to
hear for internal calls.
Note: The respective melody will be played while browsing the ringtone list.
5. Press <MENU/OK> to conrm.
7.3.2 Set the Ringer Melody for External Calls
1. Press <MENU/OK> and <UP/DOWN> to select HS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select RING SETUP.
3. Press <MENU/OK> and <UP/DOWN> to select EXT RING.
4. Press <MENU/OK> and <UP/DOWN> to select the melody you want to
hear for external calls.
Note: The respective melody will be played while browsing the ringtone list.
5. Press <MENU/OK> to conrm.
7.3.3 Set the Ringer Volume
1. Press <MENU/OK> and <UP/DOWN> to select HS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select RING SETUP.
3. Press <MENU/OK> and <UP/DOWN> to select RING VOLUME.
4. Press <MENU/OK> and <UP/DOWN> to select the desired ringer volume (a
total of 6 ringer volume levels including VOLUME OFF).
Note: The respective ringer volume will be played during your selection.
If VOLUME OFF is selected, the <Ringer Off> icon will be displayed.
5. Press <MENU/OK> to conrm.
7.3.4 Set Alert Tones
Three different alert tones are set on by default, but can be turned off, if desired.
Key Tone - a single beep is emitted when you press a key.
Low Battery Tone - emitted while you are talking on the phone to alert you that
you need to charge the handset batteries.
Out of Range Tone - emitted while you are talking on the phone to alert you to
move closer to the base unit, before the call is lost.
1. Press <MENU/OK> and <UP/DOWN> to select HS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select TONE SETUP.
3. Press <MENU/OK> and <UP/DOWN> to select KEY TONE /
BATTERY TONE / OUT OF RANGE.
4. Press <MENU/OK> and <UP/DOWN> to turn on or off these tones.
5. Press <MENU/OK> to conrm.
7.3.5 Set the Handset Language
1. Press <MENU/OK> and <UP/DOWN> to select HS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select LANGUAGE.
3. Press <MENU/OK> and <UP/DOWN> to select the desired language.
4. Press <MENU/OK> to conrm.
7.3.6 Rename the Handset
1. Press <MENU/OK> and <UP/DOWN> to select HS SETTINGS
2. Press <MENU/OK> and <UP/DOWN> to select RENAME HS.
3. Press <MENU/OK> and change the name of your handset, using <C/
MUTE> to delete letters and the alphanumeric keys to enter up to 10 letters
for the name that will be displayed on the screen in idle mode.
4. Press <MENU/OK> to conrm.
7.3.7 Choose the Information to be Displayed in Idle
You can choose to display time or handset name in your idle screen.
1. Press <MENU/OK> and <UP/DOWN> to select HS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select HS DISPLAY.
3. Press <MENU/OK> and <UP/DOWN> to select HANDSET NAME or TIME.
4. Press <MENU/OK> to conrm.
7.3.8 Set the Auto Answer
If you turn on the Auto Answer, you can answer a call automatically by just lifting
the handset off the base or charger, without having to press any key.
1. Press <MENU/OK> and <UP/DOWN> to select HS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select AUTO ANSWER.
3. Press <MENU/OK> and <UP/DOWN> to turn on or off the auto answer feature.
4. Press <MENU/OK> to conrm.
7.4 Base Settings
7.4.1 De-register a Handset
This operation should only be necessary if one of your handsets becomes faulty
or lost and needs to be replaced.
You will need to enter the 4-digit System PIN (Default PIN is 0000) in order to
de-register a handset from the base station.A de-registered handset will have
the antenna icon ashing and REGISTER on the display.
Note: You cannot de-register the handset that you are currently using.
1. Press <MENU/OK> and <UP/DOWN> to select BS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select DELETE HS.
3. Press <MENU/OK> and the display shows PIN?----.
4. Enter the 4-digit system PIN.
5. Press <MENU/OK> and the rst handset number is displayed.
6. Press <UP/DOWN> to scroll through the list of registered handsets and
select the number of the handset you want to de-register.
7. Press <MENU/OK> to conrm, and the chosen handset will be de-registered.
7.4.2 Change the dial mode(only for Tone/Pulse version)
You should normally leave the dialling mode at its default setting of TONE (also
called DTMF) unless the phone is connected to an old exchange that only
recognises PULSE dialling.
Note: If PULSE dialling is set, you can press the * key to switch to TONE
dialling for the rest of that call.
1. Press <MENU/OK> and <UP/DOWN> to select BS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select DIAL MODE.
3. Press <MENU/OK> and <UP/DOWN> to select TONE or PULSE
(The current setting is indicated by an asterisk to the right).
4. Press <MENU/OK> to conrm.
7.4.3 Change the Flash (Recall) Time
You may need to change the recall (ash) time if your phone is connected to a
PBX. The recall time options are SHORT (the default value of 100ms),
MEDIUM (300ms) or LONG (600ms).
1. Press <MENU/OK> and <UP/DOWN> to select BS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select FLASH TIME.
3. Press <MENU/OK> and <UP/DOWN> to select your desired ash time
(SHORT, MEDIUM, LONG, with the current setting indicated by an asterisk
to the right).
4. Press <MENU/OK> to conrm.
7.4.4 Change the System PIN Code
A 4-digit system PIN code is used for changing the system settings of the base
station. It is used to protect your phone against unauthorized use. The default
system PIN code is 0000.
1. Press <MENU/OK> and <UP/DOWN> to select BS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select CHANGE PIN.
3. Press <MENU/OK> and the display shows PIN? ---- .
4. Enter the current system PIN.
5. Press <MENU/OK> to display NEW PIN?---- , and enter your new 4-digit
system PIN.
6. Press <MENU/OK> to display CONFIRM?---- , and enter your new 4-digit
system PIN again.
Note: If the new PIN entered in Step 6 is not the same as the new system PIN
entered in Step 5, you must enter the new system PIN at step 5 again.
7. Press <MENU/OK> to conrm
7.5 Registration
IMPORTANT: When you purchase a phone system, all handsets are already
registered to your base, so you do not need to register them.
Handset registration is only necessary when you buy extra handsets or if a
handset has become faulty.
You can register additional handsets to have up to ve handsets per base unit,
with each handset’s number (1 to 5) shown on its display. (Note: each handset
can only be registered to one base.)
To register a new handset to your base:
1. Press and hold <FIND> on the base station until the base beeps and the
TAM indicator starts ashing, to put the base station into registration mode.
It will stay in registration mode for about 1 minute, so the following handset
sequence must be completed within this time.
2. Press <MENU/OK> and <UP/DOWN> to select REGISTRATION.
3. Press <MENU/OK> to display PIN?---- .
4. Enter the 4-digit system PIN (default 0000).
5. Press <MENU/OK> to conrm, and the display will show PLEASE WAIT..
If the handset registration is successful, you will hear a conrmation tone and
the <ANTENNA> icon will stop ashing.
The handset will automatically be allocated the next available handset number.
This handset number is shown in the handset display in standby mode. If the
handset registration is unsuccessful, the <ANTENNA> icon will still ash and
the display will return to REGISTER, so you will need to repeat the registration
process.
7.6 Reset Your Phone
You can reset your phone to the default settings . After a reset, all your
personal settings, call list entries, redial list entries, and answering machine
messages will be deleted but your phonebook remains unchanged.
1. Press <MENU/OK> and <UP/DOWN> to select DEFAULT.
2. Press <MENU/OK> to display PIN?---- .
3. Enter the 4-digit system PIN (default 0000).
4. Press <MENU/OK> to display CONFIRM?
5. Press <MENU/OK> to conrm, and the phone will be reset to its default
settings.
8 ANSWERING MACHINE
Your phone includes a telephone answering machine that records unanswered
calls when it is on.The answering machine can store up to 59 messages within
the maximum recording time of approximately 15 minutes. As well as recording
incoming messages, you can record memos for other users of your phone.
If the answering machine memory is full, the Handset will display TAM FULL
alternately with the handsets name or time, depending on the handset standby
display mode set (see section 7.3.7), and you will have to delete some
messages before any new ones can be recorded.
Some answering machine functions can be operated from the base, including
playing messages and turning the answering machine on or off. See section
“3.2 Base Station with Telephone Answering Machine (TAM) Control” for further
details of button operations.
The answering machine can also be controlled and set up using the handset
menu functions, as below.
8.1 Turn On/Off the Answering Machine
You can turn the answering machine on or off using the handset.
When the answering machine is set to ON, calls will be answered after the set
answer delay and the caller can then leave you a message.
When the answering machine is set to OFF, calls will be answered after 14
rings and the answer only message will be played to your callers. They will
not be able to leave you a message.
1. Press <MENU/OK> and <UP/DOWN> to select ANS. MACHINE.
2. Press <MENU/OK> and <UP/DOWN> to select TAM ON/OFF.
3. Press <MENU/OK> and <UP/DOWN> to select ON
OFF.
4. Press <MENU/OK> to conrm.
• If the answering machine is set to ON, the <TAM> icon displays on the
handset LCD, and the TAM indicator on the base turns on.
8.2 Listen to the Messages in the Answering Machine
When new messages are recorded on the answering machine, the <TAM> icon
ashes on the handset display until all the new messages are played. After a
new message is played it will be saved as an old message
automatically unless it is deleted.
Old messages will be played after all new messages are played completely.
1. Press <MENU/OK> and <UP/DOWN> to select ANS. MACHINE.
2. Press <MENU/OK> to show MSG PLAYBACK.
3. Press <MENU/OK> to start message playback through the earpiece and the
screen displays the date and time information of the message received.
Note: A <STAR> icon appears is placed at the centre of the bottom of the
handset display to indicate that it is a new message.
When a message has been played, the <STAR> icon will disappear and will
not be shown when you listen to this message again.
Note: If there are no messages, the handset display will briey show
“00-00 00-00” then return to MSG PLAYBACK.
4. During message playback, press <UP> or <DOWN> to increase or decrease
the message playback volume respectively.
5. Press <MENU/OK> and <UP/DOWN> to select STOP, FORWARD,
PREVIOUS, DELETE to perform the following functions during message
playback.
STOP: Stop the current message playback and return to the
ANS. MACHINE menu.
FORWARD: Skip to play the next message. The date and time information
of the next message will display if there is another message.
PREVIOUS: Repeat playing the current message from the beginning.
The date and time information of the current message will display.
DELETE: Delete the current message and the next message will be played.
Note: Alternatively, you can use the following shortcut keys to control different
operations during message playback.
Press <Key 5> to stop message playback.
Press <Key 4> once to restart the current message from the beginning. Press
twice to skip backward to play the previous message.
Press <Key 6> to skip forward to play the next message. Press <Key 2> to
delete the current message being played.
8.3 Delete All Messages in the Answering Machine
1. Press <MENU/OK> and <UP/DOWN> to select ANS. MACHINE.
2. Press <MENU/OK> and <UP/DOWN> to select DELETE ALL.
3. Press <MENU/OK> to display CONFIRM?
4. Press <MENU/OK> to delete all old messages.
Note: If there are no more messages in the answering machine, EMPTY will
display and return back to ANS. MACHINE menu.
9 TROUBLESHOOTING
Problem Causes Solutions
No dialling tone when pressing
<TALK ON>
key
a. The connection cord of the base
station is not plugged in.
b. The adapter cord is not plugged
in correctly in the base station.
c. Another handset is using the
base to make a call.
d. Wrong telephone line cord
a. Check the connections. Unplug and
plug back in the mains.
Check that the telephone cord has
been plugged into the base station and
the phone socket.
b. Check the base station plug and the
230V plug (remove and plug-in).
c. Wait until the line is unoccupied.
d. Use the original telephone line cord
supplied.
When connect to a PBX, no and/
or wrong connection after dialling
Dialling prefix is needed. Insert the dialling prefix.
SEARCHING is diaplayed a. Base station out of range.
b. Base station not connected to
mains.
Reduce the range.
Connect base station to mains.
The call does not work. Service not activated or wrong
operator or wrong setting.
Check your Subscription with network.
No display. Empty battery Recharge battery.
Answering Machine
The unit does not record new
message.
The answering machine is turned off. Turn on the answering machine.
The caller cannot leave a new
message.
a. The answering machine is
turned off.
b. Message memory is full.
c. Answer only mode is set.
a. Turn on the answering machine.
b. Erase unnecessary message.
c. Change to Ans & record mode.
I cannot operate the answering
machine remotely.
a. You are entering the wrong
remote access code.
b. You are pressing the dial keys
too quickly.
c. You are using a pulse telephone.
d. The Remote Access mode is
Deactivated.
a. If you forget the remote access code,
reset to the default settings.
b. Press each key firmly.
c. Try again using a touch tonephone.
d. Activate the Remote Access mode.
While recording an outgoing
message or listening to
message, the unit rings and
recording stops.
A call is being received. Answer the incoming call and try again to
record your out going message later.
This telephone is not equipped with a grounding function, and therefore some
of the functions may be limited when used in PBX systems.
Technical Support
If the fault persists...
Disconnect all other instruments connected to the same line as the phone
system and try to make a call.
Disconnect the base unit from the telephone line and plug a different phone
into the master telephone socket.
Try making a call. If this works, the line is OK.
If the call does not work,and you are using a two-way socket adapter, remove
it and plug a telephone directly into the socket. If the call now works, the
adapter may be faulty.
10 DECLARATION OF CONFORMITY
The conformity to the requirements is validated by the symbol.
NOTE: In compliance with Directive 2002/96/EC, when you purchase a product that comes with
the symbol shown on the right, you are required to dispose of electrical and electronic equipment
by separate waste collection and you cannot dispose of the product as normal waste.
This equipment and all its components, subsystems and consumable materials formed an
integral part of this product and when you decide to dispose of them you have to take
them to a local recycling centre for appropriate waste disposal, in compliance with
the current regulations.
Details about the location of these centres can be obtained from your local authority.
Notes for battery disposal
Your product contains batteries covered by the European Directive 2006/66/EC, which cannot
be disposed of with normal household waste.
Please be aware of the local rules on separate collection of batteries. The correct disposal of
batteries helps protect the environment and prevent health hazards.
11 GUARANTEE AND SERVICE
6.4 Delete all Call list entries
1. Follow Steps 1 and 2 in Section 6.1.
2. Press <MENU/OK> and <. UP/DOWN> to select DELETE ALL.
3. Press <MENU/OK> to display CONFIRM?.
4. Press <MENU/OK> to conrm. All entries will be deleted and the display will
show EMPTY.
7 PHONE SETTINGS
Your phone comes with a selection of settings that you can change to
personalise your phone the way you like it to work.
7.1 Date and Time Settings
If you subscribe to Caller Display the time and date settings will be automatically
updated by the network when you receive an incoming call.
The Caller Display service only sends the month and date, not the year, so you
may need to set the year.
7.1.1 Change the Date Format
1. Press <MENU/OK> and <UP/DOWN> to select HS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select DATE & TIME.
3. Press <MENU/OK> to show DATE FORMAT.
4. Press <MENU/OK> and <UP/DOWN> to select your desired date format
(DD-MM-YY or MM-DD-YY ).
5. Press <MENU/OK> to conrm.
7.1.2 Change the Time Format
1. Press <MENU/OK> and <UP/DOWN> to select HS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select DATE & TIME.
3. Press <MENU/OK> and <UP/DOWN> to select TIME FORMAT.
4. Press <MENU/OK> and <UP/DOWN> to select your desired time format
(12 HR or 24 HR).
5. Press <MENU/OK> to conrm.
7.1.3 Set the Time
1. Press <MENU/OK> and <UP/DOWN> to select HS SETTINGS.
2. Press <MENU/OK> and <UP/DOWN> to select DATE & TIME.
3. Press <MENU/OK> and <UP/DOWN> to select SET TIME.
4. Press <MENU/OK> and then enter the time information in 24 hour format.
5. Press <MENU/OK> to conrm.
Note: If the time has been set before, the current time will display, otherwise,
“HH:MM” will display.
6 CALLER DISPLAY (NETWORK DEPENDENT)
This feature is available if you have subscribed to the Calling Line Identication
service with your network service provider. Your phone can store up to 10 received
calls with date/time information in the Call List. The number will be shown on
the handset display when the phone is ringing. If the number matches with one
of the entries in your Private Phonebook, the caller’s name stored in the private
phonebook will be displayed alternately with the number, and the handset will ring
with the ringtone associated with that phonebook entry.
If the call is from someone who withheld their number, e.g. by dialling 141,
WITHHELD will display.
If the call is from someone whose number is unavailable, e.g. an international
call or from a private exchange, OUT OF AREA will display.
If you’ve got new Caller Display records, the handset will display X NEW
CALLS in standby mode. The New Calls indication will remain until all the new
call records have been viewed on that handset.
6.1 View the Call List
All received calls are saved in the Call List with the latest call at the top of the
list. When the call list is full, the oldest call will be replaced by a new call. Any
unanswered calls which have not been viewed are marked with a <*> icon at
the centre of the bottom line of the display.
1. Press <UP> to access the call list.
OR Press <MENU/OK> to show CALL LIST and then press <MENU/OK>.
2. Press <UP/DOWN> to select the desired entry.
3. Press <#> to view the caller’s number if applicable.
4. Press <MENU/OK>, <UP/DOWN> to show DETAILS, and then <MENU/
OK> to display the date and time of the call. Press <MENU/OK> to go back
to the previous screen.
6.2 Store a Call List Number into the Phonebook
1. Follow Steps 1 and 2 in Section 6.1 .
2. Press <MENU/OK> to show ADD TO PB.
3. Press <MENU/OK> and then enter the name.
4. Press <MENU/OK> and the selected call list number is displayed.
5. Edit the number if necessary.
6. Press <MENU/OK> and <UP/DOWN> to select the ringtone.
7. Press <MENU/OK> to store the phonebook entry and return to the calls list.
6.3 Delete an entry in the Call List
1. Follow Steps 1 and 2 in Section 6.1 .
2. Press <MENU/OK> and <UP/DOWN> to select DELETE.
3. Press <MENU/OK> to conrm.
8.4 Record Memo
You can record your memo message for another user. When you record
a memo, the message can be played back in the same way as answering
machine messages. Memo recording can still function even when the
answering machine is turned off.
1. Press <MENU/OK> and <UP/DOWN> to select ANS. MACHINE.
2. Press <MENU/OK> and <UP/DOWN> to select MEMO.
3. Press <MENU/OK> to start memo recording and RECORDING is displayed.
4. Press <MENU/OK> to stop memo recording. The memo will play back for
you to check. Press <MENU/OK> or leave the memo to nish playing, to
save the message. OR
ANS. MACHINE menu.
8.5 Answering Machine Settings
You can use the TAM SETTINGS menu through the handset to change the
settings of your answering machine.
8.5.1 Set the Answer Mode
By default, the answer machine is set in ANS & REC mode which allows callers
to leave a message. This mode can be changed to ANSWER ONLY which
does not allow callers to leave a message. In that case, your callers will be
prompted to call back later.
1. Press <MENU/OK> and <UP/DOWN> to select ANS. MACHINE.
2. Press <MENU/OK> and <UP/DOWN> to select TAM SETTINGS.
3. Press <MENU/OK> to show ANSWER MODE.
4. Press <MENU/OK> and <UP/DOWN> to select ANS & REC or
ANSWER ONLY.
5. Press <MENU/OK> to conrm.
When your answering machine memory is full and the answer mode is in ANS
& REC,the answer mode will change to ANSWER ONLY automatically.
It will return to ANS & REC mode automatically after some messages have
been deleted.
8.5.2 Set the Outgoing Message (OGM) Language
The answering machine announces the outgoing message when it answers a
call. There is a pre-set OGM for each of ANS & REC mode or ANSWER ONLY
mode, which can only be in English or French (Francais) on this model.
1. Press <MENU/OK> and <UP/DOWN> to select ANS. MACHINE.
2. Press <MENU/OK> and <UP/DOWN> to select TAM SETTINGS.
3. Press <MENU/OK> and <UP/DOWN> to select TAM LANGUAGE.
4. Press <MENU/OK> and <UP/DOWN> to select your desired OGM language.
5. Press <MENU/OK> to conrm.
8.5.3 Record Your Own Outgoing Message (OGM)
You can record your own OGM for ANS & REC mode or ANSWER ONLY mode.
When you record your own OGM, it will be used when the answering machine
answers the call. If your personal OGM is deleted, the pre-set OGM will be
restored automatically.
1. Press <MENU/OK> and <UP/DOWN> to select ANS. MACHINE.
2. Press <MENU/OK> and <UP/DOWN> to select TAM SETTINGS.
3. Press <MENU/OK> and <UP/DOWN> to select OGM SETTINGS.
4. Press <MENU/OK> and <UP/DOWN> to select ANS & REC or
ANSWER ONLY.
5. Press <MENU/OK> and <UP/DOWN> to select RECORD MESS.
6. Press <MENU/OK> to start recording your personal OGM and RECORDING
is displayed on the screen.
7. Press <MENU/OK> to stop and save your personal OGM. Your newly
saved OGM will playback automatically.
Alternatively, press <C/MUTE> to return to the previous screen without
saving the personal OGM.
8.5.4 Playback and Delete the Outgoing Message (OGM)
You can playback your own personal OGM or the pre-set OGM for ANS & REC
mode or ANSWER ONLY mode and choose to delete your personal
OGM during playback and record a new one whenever you want.
Please note that pre-set OGM cannot be deleted.
8.5.4.1Playback the OGM
1. Press <MENU/OK> and <UP/DOWN> to select ANS. MACHINE.
2. Press <MENU/OK> and <UP/DOWN> to select TAM SETTINGS.
3. Press <MENU/OK> and <UP/DOWN> to select OGM SETTINGS.
4. Press <MENU/OK> and <UP/DOWN> to select ANS & REC or
ANSWER ONLY.
5. Press <MENU/OK> and <UP/DOWN> to select PLAYBACK.
6. Press <MENU/OK> to playback your current OGM and PLAYING OGM
is displayed on the screen.
7. Press <MENU/OK> to stop the OGM playback and return to the previous menu.
Note: If a personal OGM has not been recorded, the pre-set OGM will be played.
8.5.4.2 Delete a Personal OGM
1. Repeat Steps 1 to 6 in Section 8.5.4.1
2. Press <C/MUTE> while the OGM is playing to delete your personal OGM
and return to the previous menu and the pre-set OGM is restored automatically.
Note: If the pre-set OGM is playing, you are not allowed to delete it, so
pressing <C/MUTE> will just stop the playback and return to the previous menu.
8.5.5 Set the Answer Delay
You can set the number of rings before the answering machine answers and
starts playing your OGM. You can set the answering machine to answer after
two to eight rings or TIME SAVER. If Time Saver is set the answering machine
will answer after 4 rings if there are no new messages, or after 2 rings if there is
a new message, so if you call in and you don’t get an answer after 2 or 3 rings,
you can hang up and save on call charges.
1. Press <MENU/OK> and <UP/DOWN> to select ANS. MACHINE.
2. Press <MENU/OK> and <UP/DOWN> to select TAM SETTINGS.
3. Press <MENU/OK> and <UP/DOWN> to select ANSWER DELAY.
4. Press <MENU/OK> and <UP/DOWN> to select from 2 RINGS, 4 RINGS,
6 RINGS, 8 RINGS or TIME SAVER.
5. Press <MENU/OK> to conrm.
8.5.6 Set the Recording Time of Incoming Message
You can set the maximum length of the recording time for each incoming
message to be 60, 120, 180 seconds or unlimited up to the total recording time
remaining on the answer machine.
1. Press <MENU/OK> and <UP/DOWN> to select ANS. MACHINE.
2. Press <MENU/OK> and <UP/DOWN> to select TAM SETTINGS.
3. Press <MENU/OK> and <UP/DOWN> to select RECORD TIME.
4. Press <MENU/OK> and <UP/DOWN> to select from 60 S, 120 S, 180 S or
UNLIMITED.
5. Press <MENU/OK> to conrm.
8.5.7 Call Screening
When the answering machine is on and takes a call, you can listen to the caller
leaving a message. You can then identify the caller and decide whether to take
the call in person.
If the answering machine is set to ON, when there is an incoming message,
it will automatically be played through the base station, but you also have the
option to listen through the handset which will display SCREENING?
1. Press <MENU/OK> to start call screening. Any handset can listen to who is
leaving the message and decide whether to pick up the call or not.
2. The handset will display SCREENING?.
3. You can adjust the earpiece volume by pressing <UP> or <DOWN>, OR
Press <C/MUTE> to stop screening and leave the message recording.
At any time if you want to pick up the call, you can press <TALK ON> and
the message recording stops automatically. If the answering machine is in
the process of recording, the message already stored will be saved.
8.5.8 Change the Compression Rate
Three different compression rates (HIGH, MEDIUM and LOW) are provided for
you to select different quality levels of recording incoming message. The lower
the compression rate, the higher the recording quality level attained, but the
shorter the total recording time available. ( LOW=7 minutes, MEDIUM=10
minutes, HIGH=15 minutes approx).
1. Press <MENU/OK> and <UP/DOWN> to select ANS. MACHINE.
2. Press <MENU/OK> and <UP/DOWN> to select TAM SETTINGS.
3. Press <MENU/OK> and <UP/DOWN> to select COMPRESSION.
4. Press <MENU/OK> and <UP/DOWN> to select your desired compression
rate.
5. Press <MENU/OK> to conrm.
8.5.9 Activate Remote Access
Your phone lets you check your messages, or otherwise operate your
answering machine, by calling the answering machine when you are away from
home and then dialling a 4-digit remote access PIN from a tone-dialling phone.
The 4-digit remote access PIN code is used to prevent other people from
unauthorised access of your answering machine.
8.5.9.1 Change the 4-Digit Remote Access PIN
1. Press <MENU/OK> and <UP/DOWN> to select ANS. MACHINE.
2. Press <MENU/OK> and <UP/DOWN> to select TAM SETTINGS.
3. Press <MENU/OK> and <UP/DOWN> to select CHANGE PIN.
4. Press <MENU/OK> to display PIN? ----, and then enter the current PIN
(Default 0000).
5. Press <MENU/OK> to display NEW PIN? ----, and then enter your new
4-digit PIN code.
6. Press <MENU/OK> to display CONFIRM? ----, and then enter your new
4-digit PIN code again.
7. Press <MENU/OK> to conrm the new PIN.
Note: If the new PIN entered in Step 6 is not the same as the new system PIN
entered in Step 5, you must enter the new system PIN at step 5 again.
8.5.9.2 Activate or Deactivate the Remote Access
To allow remote access this option must be turned ON, but you can turn it OFF
to prevent any remote access at all.
1. Press <MENU/OK> and <UP/DOWN> to select ANS. MACHINE.
2. Press <MENU/OK> and <UP/DOWN> to select TAM SETTINGS.
3. Press <MENU/OK> and <UP/DOWN> to select REMOTE ACC.
4. Press <MENU/OK> and <UP/DOWN> to select ON or OFF to turn the
remote access on or off respectively.
5. Press <MENU/OK> to conrm.
8.5.9.3 Access Your Answering Machine Remotely
You can ring your phone from another tone-dialling phone to switch the
answering machine on or off, and/or listen to your messages remotely.
1. Place a call from a tone-dialling phone to your phone.
2. When the answering machine answers the call and starts playing the OGM,
press the < * > key. The OGM will stop playing.
3. Enter the 4-digit Remote Access PIN (default PIN is 0000).
You will hear a single conrmation beep if the PIN is accepted, and you then
need to press 5 to start playing any messages.
Note: The * must be entered while the OGM is still playing, and the 4-digit PIN
should follow without any delays.
Note: If the 4-digit Remote Access PIN is entered incorrectly you will hear three
error beeps, and you can try again, but if it happens three times.
consecutively, the line will be released automatically.
4. Press the following keys to carry out your desired function.
Note: If your answering machine is switched off, the phone will enter into the
remote access mode after 14 rings and play the Answer Only OGM.
You can then enter the < * > key and the 4-digit remote access PIN (Default
Remote Access PIN is 0000) to activate the remote access feature.
When your answering machine memory is full and the answer mode is set to
Answer & Record, the answer mode will change to Answer Only automatically.
It will change back to Answer & Record mode automatically after some
messages have been deleted.
)XQFWLRQV
.H\V
:KLOHPHVVDJHLVQRWSOD\LQJ :KLOHPHVVDJHLVSOD\LQJ
'HOHWHWKHFXUUHQWPHVVDJHSOD\ing
5HSHDWSOD\LQJWKHFXUUHQWPHVVDJH
IURPWKHEHJLQQLQJ3UHVVWZLFHWRVNLS
EDFNZDUGWRSOD\WKHSUHYLRXVPHVVDJH
3OD\WKHPHVVDJH 6WRSWKHFXUUHQWPHVVDJHSOD\EDFN
6NLSWRSOD\WKHQH[WPHVVDJH
7XUQRQWKHDQVZHULQJPDFKLQH
6WRSWKHFXUUHQWPHVVDJHSOD\EDFN
7XUQRIIWKHDQVZHULQJPDFKLQH
Binatone Electronics International Limited
Floor 23A, 9 Des Voeux Road West, Hong Kong
Tel: (852) 2802 7388 Fax: (852) 2802 8138
________________________________________
EC Declaration of Conformity
We the manufacturer / Importer : Binatone Electronics International Limited
Floor 23A, 9 Des Voeux Road West, Hong Kong
Tel: (852) 2802 7388 Fax: (852) 2802 8138
Declare under our sole responsibility that the following product
Type of equipment: Digital cordless telephone with Answering Machine
Model Name: Vantage 6020 series
Country of Origin: China
Brand: Binatone
complies with the essential protection requirements of R&TTE Directive 1999/5/EC on the
approximation of the laws of the Member States relating to Radio Spectrum Matters, the Council
Directive 2004/108/EC on the approximation of the laws of the Member States relating to
electromagnetic compatibility (EMC) and the European Community Directive 2006/95/EC relating to
Electrical Safety , Directive 2011/65/EC on the restriction of use of hazardous substances (RoHS) and
2009/125/EC relating to ecodesign requirement for Energy-Related Products (ErP).
Assessment of compliance of the product with the requirements relating to the essential requirements
according to Article 3 R&TTE was based on Annex III of the Directive 1999/5/EC and the following
standard / regulation:
Radio Spectrum: EN 301406: V2.1.1 (2009-07);
EMC: EN 301489-6:V1.3.1 (2008-08);
EN 301489-1:V1.9.2 (2011-09);
EN55022:2010
EN55024:1998 +A1 +A2:2003
EN61000-3-2:2006 +A1 +A2:2009
EN61000-3-3:2008
Heath & Electrical Safety: EN 60950-1:2006 + A11+A1+A12:2011
EN50360:2001 +A1:2012 & EN50385 : 2002
ErP Implementing regulation EC1275/2008
Manufacturer / Importer
(Signature of authorized person) 1 Apr 2013
Date
This product is guaranteed against manufacturing defects for a period of 1 Year.
This does not cover the product where the fault is due to misuse, abuse,
use in contravention of the instructions, or where the product has been
subject of commercial use.
In the event of a problem with the product within the guarantee period please
the subject of unauthorised modifications or alterations, or has been the
return it to your nearest Argos store.If the item is shown to have had an
inherent defect present at the time of sale, the store will provide you with
a replacement.
Your statutory rights remain unaffected.
Guarantor; Argos Ltd
489 - 499 Avebury Boulevard
Central Milton Keynes
MK9 2NW
5. Press <C/MUTE> to stop memo recording without saving and return back to
4.
Loading...