Bernina 380, 350 PE, 350 Special Edition, 330 Owner's Manual

BERNINA 330 | 350 PE | 380
Introduction
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
Dear Bernina Customer,
You’ve decided on BERNINA, a reliable choice that will delight you for years to come. For over 100 years, our family has placed the highest value on satisfied customers. For myself, it is a matter of personal pride to offer you Swiss precision at the height of perfection, future-oriented sewing technology, and a comprehensive customer service.
The BERNINA 330, 350 and 380 are primarily aimed at the occasional sewer who puts great stock in design and customer benefit. These sewing computers are very ergonomi­cally built and therefore even easier to operate, to help you, our esteemed customers, on your journey to even greater sewing pleasure and perfect results.
1
Enjoy creative sewing with BERNINA: Find out about our varied range of accessory and let yourself be inspired by new sewing projects at www.bernina.com.
And don’t forget to make use of service and maintenance offers from our highly trained BERNINA dealers.
H.P. Ueltschi Owner BERNINA International AG CH-8266 Steckborn www.bernina.com
2
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
Safety Instructions
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic safety precautions should always be followed, including the following:
Read all instructions before using this sewing computer.
When the sewing computer is not in use, it should be disconnected from the electricity supply by removing the plug from the outlet.
DANGER!
To reduce the risk of electrical shock:
1. The sewing computer should never be left unattended when plugged in.
2. Always unplug the sewing computer from the electrical outlet immediately after using and before cleaning.
3. LED radiation. Do not view directly with optical instruments. LED class 1M
WARNING!
To reduce the risk of burns, fire, electric shock or injury to persons:
1. Use the sewing computer only for purposes as described in this manual. Use only attachments/accessory recommended by the manufacturer as contained in this manual.
2. Do not allow the sewing computer to be used as a toy. Close attention is necessary when this sewing computer is used by or near children and infirm persons. This sewing computer is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the sewing computer by a person responsible for their safety. Children must be kept under supervision to ensure that they do not play with the sewing computer.
3. Never operate this sewing computer if:
it has a damaged cord or plug
it is not working properly
it has been dropped or damaged
it has fallen into water Take the sewing computer to the nearest authorized BERNINA dealer for examination, repair, electrical or mechanical adjustment.
4. Never operate the sewing computer with any air vents blocked. Keep ventilation openings of the sewing computer free from lint, dust and/or fabric bits.
5. Keep fingers away from all moving parts. Special care is required in the needle area of the sewing computer.
6. Never drop or insert any objects into any opening on the sewing computer.
7. Do not use the sewing computer outdoors.
8. Do not operate the sewing computer where
aerosol products (spray) or oxygen is being administered.
9. Do not pull or push the fabric while stitching. This may deflect the needle, causing it to break.
10. Do not use bent needles.
11. Always use the BERNINA original stitch
plate. The wrong stitch plate can cause needle breakage.
12. To disconnect, turn power switch to «0» (off), then remove the plug from the outlet. Do not unplug by pulling the cord, instead grasp the plug to pull it from the outlet.
13. Turn power switch to «0» (off) when making any adjustments in the needle area, such as changing the needle or the presser foot, etc.
14. Always unplug the sewing computer from the electrical outlet when carrying out cleaning or maintenance work or any other user servicing adjustments mentioned in this manual.
15. This sewing computer is provided with double insulation (except USA and Canada). Use only genuine replacement parts. Please note the advice on the servicing of double­insulated products.
Safety Instructions
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
3
SERVICING DOUBLE INSULATED PRODUCTS
In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means is provided on a double­insulated product nor should a means for grounded be added to the product. Servicing a double-insulated product requires extreme care and knowledge of the system and should only be done by qualified service personnel. Replacement parts for a double-insulated product must be identical to the original parts in the product. A double insulated product is marked with the words: «Double-Insulation» or «double-insulated».
The symbol product.
may also be marked on the
DISCLAIMER
No liability will be assumed for any possible damage which arises from misuse of this sewing computer.
SAVE THESE INSTRUCTIONS!
Please find the latest version of your instruction manual at
www.bernina.com
Environmental Protection
BERNINA is committed to the protection of the environment. We strive to minimize the environmental impact of our products by continuously improving product design and our technology of manufacturing.
At end of life please dispose this product in an environmentally responsible way according to the national directive. Do
not throw away this product with your household waste. In case of doubt, please contact your dealer.
This sewing computer is intended for household use only.
If the sewing computer is stored in a cold room, it should be brought to a warm room about one hour before use.
4
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
Contents - Key to Signs
Accessory
Preparation
Details of the sewing computer 8
Preparation for sewing 10
Functions
Function buttons on the sewing computer 24
Details of the screen 26
Sewing stitches
Practical stitches 30
Examples of application 31
Cleaning, maintenance
Sewing computer and screen 44
Lubricating 44
Memory 27
Buttonholes 36
Practical-/Quiltstitch 43
5-7
8-23
24-29
30-43
44
Troubleshooting
Stitch patterns
Index
Glossary
Balance Correcting abnormalities in stitch formation due to the fabric clr Deleting settings or data LED Sewing light system FHS Free-Hand System = Knee-operated presser-foot lifter mem Memory = Longterm data store Bartack Buttonhole-bead cross-connections Satin stitching Dense zig-zag Fabric fold Folded edge of material Hook «Catches» the needle-thread loop, forming
the seam together with the lower thread
45
46
47-49
Very important! Risk of damage!
Supplementary information!
* Not supplied as standard with the BERNINA 330 ** Not supplied as standard with the BERNINA 350 *** Not supplied as standard with the BERNINA 380
Standard Accessory
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
3 4 6
2
5
Fabric cover
Accessory box */**
Accessory case ***
Foot control
Power cable
Slide-on table*
Stitch pattern summary card
Free-Hand System FHS */**
Accessory
1 5 bobbins (one of them in the bobbin case) 2 Selection of needles
5
3 Seam guide, right 4 Height compensating tool 5 Seam ripper 6 Screwdriver, red
7
8
7 Angular Torx button 8 Lint brush 9 Lubricator 10 2 foam pads
9
11 3 spool discs
11
1
10
6
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
Accessory
Presser Feet/Snap-On Soles (BERNINA 330/350/350 PE/380)
1
4
6
2
5
7
3
8
Presser Feet - Standard (BERNINA 350/350 PE/380)
1
2
3
4
1 No. 1 Reverse pattern sole 2 No. 2 Overlock sole (without 350 PE) 3 No. 3A Automatic Buttonhole foot with
slide
4 No. 4 Zipper sole 5 No. 5 Blindstitch sole 6 No. 8 Jeans sole */**/(without
350 PE)
7 No. 20 Open embroidery sole * 8 No. 37 Patchwork sole (only 350 PE)
1 No. 1 Reverse pattern foot 2 No. 2 Overlock foot (without 350 PE) 3 No. 3A Automatic Buttonhole foot with
slide
4 No. 4 Zipper foot 5 No. 5 Blindstitch foot 6 No. 8 Jeans foot **/(without 350 PE) 7 No. 20 Open embroidery foot 8 No. 37 Patchwork foot (only 350 PE)
5
6
7 8
Presser Feet: can vary from country to country (Snap-On Soles or Standard).
More accessories you can found on www.bernina.com
Accessory Box */**
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
Accessory
Storing Accessory
Standard accessory are supplied in a plastic bag. They can be stored as shown in the picture.
7
Accessory Case ***
Standard accessory for the models B330/350 can be carefully stored in the case. Buttonhole foot 3A is stored inside in a separate compartment.
8
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
Preparation - Details of the sewing computer
Front View
9
8
17
10
7
5
4
2
11
12
13 14
6
3
16
15
18
23
19
20
21
33
22
24
Detail View
1
40
39
41
25
26
44
42
43
Preparation - Details of the sewing computer
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
9
27
9
28
2 Stitch plate 3 Attachment base for
special accessory
1 Bobbin cover
18
31
29
30
4 LED sewing light 5 Quick reverse button 6 Start/Stop button 7 Thread take-up cover 8 Thread take-up lever
32
9 Bobbin winder pre-tension 10 Speed control 11 Screen 12 Needle stop up/down
button
13 Pattern end button 14 Mirror image button */** 15 Stitch length buttons
33
16 Needle position buttons 17 Stitch width buttons 18 Bobbin winder device 19 Thread cutter on bobbin
winder
20 Memory buttons 21 Alphabet button 22 Stitch selection buttons
34
37
23 #-button (hash button)
26 FHS (Free Hand System)
connection *
27 Thread tension adjustment
wheel
28 Rear thread guide 29 Carrying handle 30 Vertical spool pin 31 Horizontal spool pin 32 Eyelet 33 Handwheel 34 Balance adjuster 35 Foot control socket 36 Feed-dog drop 37 Power switch on/off 38 Power plug socket 39 Needle threader 40 Thread guide 41 Needle clamp 42 Presser Foot 43 Thread cutter in hook
opening
44 Feed dog 45 Thread cutter on head
frame (left)
46 Presser foot lifter
47 Darning hoop connection 24 «clr» (clear) button 25 Slide-on table socket
38
47
35
36
(USA/Canada only): The sewing computer has a polarized plug (one blade wider than the other). To reduce the risk of electrical shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way!
45
46
3
25
2
10
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
Preparation - Sewing
Foot Control
Sewing speed control
control the sewing speed by pressing the foot control
Self storing cord
wind the cable around the spool
insert the plug into the groove provided
While sewing
unwind the cable
LED Sewing Light
Slide-on Table *
The LED sewing light illuminates the sewing area and has a long product life.
Please note that a defective sewing light must ONLY be re­placed by an authorized technician.
The sewing computer must be taken to an authorized BERNINA dealer!
The slide-on table increases the sewing surface.
Attaching the slide-on table
raise needle and presser foot
slide over free-arm to the right until it engages
Removing the slide-on table
raise needle and presser foot
press button down and pull off slide-on table to the left
Presser Foot Lifter (FHS) */**
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
Preparation - Sewing
The FHS raises and lowers the presser foot.
Attaching the lifter
insert into the opening; you should be able to operate the FHS with your knee in your normal sitting position
Raising and lowering the presser foot
with your knee push lever to the right
the presser foot is raised; the feed dog is lowered simultaneously. The thread tension is released
the feed dog is raised as soon as the first stitch is sewn
Your dealer can adjust the FHS if necessary.
11
Vertical Spool Pin
the vertical spool pin is on the side behind the handwheel
it is an essential aid for sewing with more than one thread, i.e. double need­le work
raise the pin until it clicks into its vertical position
when using large reels, add the foam pad A for stability
A
12
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
Preparation - Sewing
Winding a Bobbin
turn power switch on (to «I»)
place empty bobbin on spindle
place thread on spool pin
attach appropriate spool disc; diameter of thread spool determines disc size
following the direction of the arrow take thread through the rear guide and round the pre-tension stud
wind the thread two to three times around the empty bobbin and cut off any excess thread on the thread cutter
push engaging lever against bobbin, the winder works automatically
the motor will stop automatically when the bobbin is full
Thread cutter
pull thread over thread cutter when removing the bobbin
Inserting a Bobbin
Bobbin winding while sewing
place thread spool on vertical spool pin then, following the direction of the arrow, take thread through the thread guide and around the pre-tension stud
then proceed as mentioned above
Insert the bobbin so that the thread runs clockwise.
Laying the thread into the slot
Pull the thread counter clockwise into the slot.
Pulling the thread under the spring
Pull the thread to the left under the spring until it lies in the T-shaped slit at the end of the spring. The bobbin must turn clockwise.
Bobbin Case
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
Preparation - Sewing
13
To remove the bobbin case
raise needle
power switch to «0» (off)
open the bobbin cover
grasp the latch of the bobbin case
remove bobbin case
To insert the bobbin case
hold the bobbin case latch
the finger on the case should point upwards
insert the case so that it clicks into place
The bobbin thread does not have to be brought up as the loose end is just the right length to start sewing.
Bobbin thread cutter
insert the bobbin case
take the thread over cutter A and cut it
A
close the bobbin cover
14
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
Preparation - Sewing
Needle Threader
A
B
1 Press lever down
raise needle
lower the presser foot
hold thread to the left and back
press lever A down and simultaneously guide the thread around hook B to the right to the needle
2 Guide thread to front of the needle
put the thread from the front into the guide C until it catches in the wire hook
1
2
A
3
Threading the Upper Thread
A
B
D
C
3 Release lever and thread
release lever A and thread
put the thread under the foot and pull the thread backwards or
put the thread under the foot and pull it from front to back over the thread cutter on left side of the head frame
Attaching the thread spool
raise the needle and presser foot
power switch to «0» (off)
place foam pad on pin base
place spool on pin (thread unwinds clockwise)
attach appropriate spool disc - diameter of spool determines disc size, there must be no clearance between the disc and the spool
take thread through rear guide A
then into slit of upper thread tension B
pull thread down to the right of the take-up cover and around C
take thread up to the left of the cover and around D, placing it in the take-up lever
take thread down and through guides E and F
C
E
F
Threading the Double Needle
033301.71.04_2014-02_Manual_B330_B350_PE_B380_EN
Preparation - Sewing
Threading the First Thread
place thread spool on horizontal spool pin and thread
guide the thread to the front in the slit and past the tension disc A on the right side
thread sewing computer as usual and thread the right needle
15
A
Threading the Second Thread
place thread spool on the vertical spool pin and thread
guide the thread to the front in the slit and past the tension disc A on the left side
thread the left needle
threads must not be twisted together
Threading the Triple Needle
two thread spools and one full bobbin are needed
place one thread spool on horizontal spool pin
A
place second thread spool and the bobbin, separated by a spool disc, on vertical spool pin (both spools have to turn in the same direction)
thread as usual by guiding two threads on the left side of the tension disc A and one thread on the right side of the disc
Loading...
+ 36 hidden pages