Page 1
SCOUT220-IS and SCOUT240-IS Portable
Data Collectors
Datasheet
Bently Nevada Machinery Condition Monitoring
Description
SCOUT220-IS and SCOUT240IS are intrinsically safe portable
data collector solutions designed to monitor machinery
conditions in hazardous environments. Both are rated ATEX
Zone1 / Zone21 (for gases and non-conductive dust) and
CSA Class1 / Div1. These small form-factor, rugged devices
take vibration recordings and upload the collected data for
detailed analysis in System 1.
This is a two-part solution. The SCOUT data collector uses
Bluetooth to communicate with a wireless, industrial
handheld device running the S1 Collector app.
You can carry the data acquisition module using a shoulder
strap, allowing you to focus on your job and move safely
between machines. Vibration recordings are viewed and
stored on the available handheld device. The handheld runs
the Android OS, so you can use it like any smartphone or
tablet to take pictures and video, send text messages, check
email, make phone calls, track your location, create SOS
alerts, and run other enterprise apps on the same device.
109M0226 Rev. P
The high performance data acquisition module provides long
battery life, and is light weight & rugged. You can sample up
to four sensor channels simultaneously using optional
tachometer or Keyphasor triggering. The data acquisition
module provides up to ten hours of continuous use, while
supporting an F
resolution.
System 1, paired with SCOUT220IS and SCOUT240IS, enables
you to track all of your machinery using a single enterprise
monitoring system. Use System 1 to prepare routes, analyze
data, detect long-term trends, and set and detect alarms.
Then transfer the routes between System 1and your SCOUT
device using WiFi, file transfer, cellular network, or a USBcable.
up to 80 kHz and 12,800lines of spectral
max
Page 2
SCOUT220-IS and SCOUT240-IS Portable Data Collectors
Datasheet 109M0226 Rev. P
Hardware Features
l Battery lifeof 10 hours allows the data
collector to run all day.
l Five year warranty.
l Rugged, water, and dust resistant (IP-65),
drop-tested, with intrinsically safe
variants.
l Easy to carry: lightweight handheld unit,
shoulder strap for data collector, keepers
for sensors.
l Safety breakaways on both shoulder
strap and sensor cables.
l Upgradable industrial handheld
smartphone or tablet.
Software Features
l Seamless on-and off-route data
collection.
l Route overview and easy route
navigation.
l Up to four channel simultaneous
recordings (including on-route).
l Fast sensor settling and data collection.
l Patented 6Pack time-saving
measurement type.
l Synchronous sampling, peak demod,
and bump test.
l Coast-down, run-up, and interval
capture support.
l Custom note and numeric data entry.
l Up to 12,800 lines of spectral resolution,
80kHz F
l Data quality warnings and easy-to-
max
.
understand alarm annunciation.
l Supports operator driven reliability (ODR).
l Supports accelerometer, velocity,
displacement, and voltage-output
sensors of AC and DC coupling types.
The SCOUTportable connects via Bluetooth to
the handheld, which you can then sync with
System 1.
2/12
Page 3
SCOUT220-IS and SCOUT240-IS Portable Data Collectors
Datasheet 109M0226 Rev. P
Tachometer
Data Collector Specifications
Sensors
Sensor input
Simultaneous
sampling
Compatible
sensor types
AC coupled
range
DC coupled
ranges
Connectors
Analog to
digital
conversion
Sensor
excitation
current
SCOUT220-IS: 2 channels.
SCOUT240IS: 4 channels.
Accelerometer, velocity,
displacement, and voltage.
16 V peak-peak.
Allows for ± 8 V sensor output
swing (± 80 g).
0 to 20 V, -10 to 10 V, -20 to 0 V
2 x LEMOconnectors for CH1 &
CH2+
1 X LEMO connector for
Tach/Keyphasor
SCOUT240IS includes a CH 2.4
breakout cable.
24-bit ADC
0 mA or 2.2 mA
(configurable), 24V
maximum
2.2 mA powers IEPE/ICP-type
sensors
Optional IS
Zone 0 rated
laser Tach
Optional
Zone 2 rated
laser Tach
Other sensor
types
supported
Power supply
to sensor
Input
Impedance &
max values
Waveform
display
Threshold ± 20 V range ± 0.4 V accuracy
Autothreshold
mode
Battery-powered, handheld
laser sensor.
Triggers when beam on
reflectivetape range 10 cm to
2 m.
Speed 6 to 250 krpm.
Laser sensor powered by
Portable Data Collectors.
Triggers when beam on
reflectivetape range 10cm to
2m. Speed 6 to 250 krpm.
Contact, TTL Pulse, Keyphasor
5 V, 40 mA
Rated for Zone 2, 22 and
Division 2 only.
100KΩ
± 28 V max
± 20 V range
pk-pk
3 V
15 s max settling time
minimum signal
Sensor
detection
Measures sensor bias voltage.
Warns if short circuit or not
connected.
Hysteresis 0.2 V to 2.5 V user
configurable
Speed range
Signal pulse
width
Accuracy
3/12
Minimum: 60 rpm (1 Hz)
Maximum: 1,200,000rpm (20
kHz)
10 µs minimum 2% duty cycle
(for auto-threshold)
± (0.1 % + 1 cpm) for speeds up
to 5 kHz (300 kcpm)
± (0.3 %) for speeds above 5
kHz (300 kcpm).
.
Page 4
SCOUT220-IS and SCOUT240-IS Portable Data Collectors
Datasheet 109M0226 Rev. P
Parameter Indication
Dynamic
signal range
Harmonic
distortion
Units
Magnitude &
cursors
Base
accuracy
High
frequency
attenuation
AC coupling
attenuation
Attenuation
due to
Integration
> 95 dB typical at 400 line
resolution
Less than -70 dB typical.
Other distortions and noise
are lower.
g or m/s
2
in/s or mm/s
mil or mm or µm
peak, or peak-peak, or RMS
Overall value: RMS, derived pk,
derived pk-pk Dual cursors
Digital readouts on chart
For AC signal: ± 1% of readings
For DC level: ± 1% of full scale
(1% is approximately 0.1 dB)
≤ 0.1 dB > 100 Hz to 10 kHz
≤ 3 dB > 10 kHz to 40 kHz
Attenuation tolerances are in
addition to base accuracy.
≤ 0.1 dB 10 Hz to < 100 Hz
≤ 3 dB 1 Hz to < 10Hz
≤ 0.1 dB 10 Hz to < 100 Hz
≤ 1.5 dB 1 Hz to < 10 Hz.
Values apply to single
integration (acceleration to
velocity). Double the values
for double integration
(acceleration to
displacement).
Spectrum Display
max
F
ranges 25; 50; 100; 125; 150; 200; 300;
400; 500; 600; 800; 1,000; 1,200;
1,600; 2,000; 2,500; 3,000;
4,000; 5,000; 6,000; 8,000;
10,000; 15,000; 20,000; 30,000;
40,000; 60,000; 80,000 Hz or
equivalen. CPM values or
orders-based from 1X to 999X.
Resolution
(Spectral
lines)
Frequency
scale
Amplitude
scale
400; 800; 1,600; 3,200; 6,400;
12,800 lines
Channels
3 or 4 N/A 3,200
220
max lines
1 6,400 12,800
2 3,200 6,400
240
max lines
Hz, CPM, Orders.
Linear scale with zooming.
Acceleration, velocity,
displacement.
Linear auto scaling.
Window
Hanning, Rectangular
shapes
Overlap (0, 12.5, 25, 37.5, 50, 62.5, 75,
87.5) % Dependent on F
max
and number of lines
Number of
averages
1, 2, 4, 8, 16, 32, 64, 128
Increases sampling time
proportionally
Averaging
Linear, exponential, peak hold
types
Demodulation
bandwidths
23 bandwidth options from
125 Hz to 1,250 Hz and up to 16
kHz to 20 kHz.
Peak demod: 500Hz-40kHz, 140kHz, 2-40kHz, 5-40kHz
6Pack Up to 40 kHz & 3,200 lines (1
channel).
Up to 20 kHz & 1,600 lines (2-3
channels).
Spectrum and waveform for
each of low-frequency, highfrequency, demodulation
min
F
range
possible
0 to F
max.
Instrument zeroes all spectral
lines below F
min
.
4/12
Page 5
SCOUT220-IS and SCOUT240-IS Portable Data Collectors
Datasheet 109M0226 Rev. P
Waveform Display
Number of
samples
Time scale 10 ms to 256 seconds or orders
1,024; 2,048; 4,096; 8,192; 16,384;
32,768
Channels
2 8,192 16,384
3 or 4 N/A 8,192
220
max
samples
1 16,384 32,768
240
max
samples
based from 1 to 999 revs
Communication
Bluetooth BT 4.0 Classic
Battery and Charger
Battery type
Custom Lithium Ion pack, 7.4,
4000 mAh.
Mechanical
Size
Weight 1.5 lb ≈ 680g
5.1” W x 5.1” L x 1.4” H
(130 mm Wx 130 mm Lx 35
mm H
Environmental Limits
Operating
temperature
Ambient
temperature
for charging
battery
Storage
temperature
& humidity
-4°F to 140°F (-20 to 60°C)
122°F (50°C) max when used in
Ex hazardous areas
0 to 25°C (32 to 77°F)
-4 to 140°F (-20 to 60°C),
95%relative humidity If
storage exceeds one month:
up to 95°F (35°C), 85% relative
humidity.
Not user accessiblebut
factory replaceable.
Operating
Time
Charger type
10 hours typical on-route data
collection
Internal charging, automatic
control.
External power pack 12 V DC, 3
A output.
Charge rate 2 A nominal 3 hours for
complete charge.
Ruggedness
drop &
sealing
Drop spec MIL-STD-810F-516.5IV 26 drops at 4' (1.2 m) onto
concrete
IP65
5/12
Page 6
SCOUT220-IS and SCOUT240-IS Portable Data Collectors
Datasheet 109M0226 Rev. P
Handheld Specifications Summary
Ahandheld devices is not included in
the SCOUT kit. To order a device, add it as
an accessory item, or obtain an
appropriately rated device directly from
the supplier.
Device name
Device image
Display & Touch 5”, Gorilla glass, glove touch
Smart Ex 02 DZ1
Smart Ex 02 DZ2
&wet mode
Device name
(DZ1 model) Ex ib IIC T4 Gb IP64
Hazardous Area
Rating
(DZ2 model)
Complete &
Latest Specs
Smart Ex 02 DZ1
Smart Ex 02 DZ2
Ex ib IIIC T120°C Db
CSA:
Class I, II, III Division 1
Groups A–G, T4
IECEx, ATEX,:
Zone 2/22
Ex ic IIC T4 Gc IP64
Ex ic IIICT120°C Dc
CSA:
Class I, II, III Division 2
Groups A–G, T4
www.ecom-ex.com
Wireless and
GPS
Cameras 12 MP rear, 5 MP front
OS Android 9.0
CPU Qualcomm Snapdragon
Battery Replaceable Li-Ion 4400
Size
Weight
Memory 3 GB RAM
Ruggedness IP68, MIL-STD-810G, -20 to
Warranty 3 years
4G/LTE dual SIM,
WiFi 2.4 & 5 GHz,
BT 4.2, NFC, GPS
450
mAh
163 x 82 x 22 mm
(6.4 x 3.2 x 0.87 in),
380 g
32 GB ROM
Up to 128 GB microSD
60°C (-4 to 140°F)
Hazardous Area
Rating
IECEx, ATEX,:
Zone 1/21
6/12
Page 7
SCOUT220-IS and SCOUT240-IS Portable Data Collectors
Datasheet 109M0226 Rev. P
Zone 20, Ex/AEx ia [ia Ga] IIIB
Compliance and Certifications
T135°C Da
Zone 22, Ex/AEx ic [ic Gc] IIIB
T135°C Dc
This section applies only to the Data
Collector, not the handheld device.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference.
2. This devicemust accept any interference
received, including interference that may
cause undesired operation.
For the detailed listing of country and
product specific approvals, refer to the
Approvals Quick Reference Guide
(108M1756) available from
BNTechSupport.com.
RED/EMC
EN 61000-6-2
EN 61000-6-4
EN 300 328
EN 301 489-1
EN 301 489-17
EN 61326-1
2014/53/EU
2014/30/EU
ATEX/IECEx
II 1 (1) GD
II 3 (3) GD
Ex ia [ia] IIC T4 Ga
Ex ic [ic] IIC T4 Gc
Ex ia [ia Ga] IIIB T135°C Da
Ex ic [ic Gc] IIIB T135°C Dc
T4 @ Ta = -20°C to +50°C
The installation must comply
with the SCOUT2220/240
Hazardous Location Installation
Control Drawing (document
111M0029).
ROHS 2011/65/EU
The above ratings include the following areas:
n Intrinsically safe Zone 0, 20 and Division 1
n Lower level protection of Zone 2, 22 and
Division 2
Only the following restricted sensor types are
certified for intrinsically safe use:
n SCOUT-powered sensors such as ICP/IEPE
accelerometers
n Self-powered tachometers such as
battery-powered handheld laser
tachometers
You can use other types of sensors such as
buffered outputs from instrumentation racks
only in lower rated Zone 2, Division 2 areas. Refer
to SCOUT2220/240 Hazardous Location
Installation Control Drawing (document
111M0029) for details.
For the optional dust certification (Class
II Groups F and G, and Zones 20 and 22),
special dust-certified sensors are
required. If this is required, inform your
Bently Nevada sales professional so that
the correct sensor can be substituted.
CSA/NRTL/C
Class I Division 1 Groups ABCD
Class I Division 2 Groups ABCD
Class II Division 1 Groups FG
Class II Division 2 Groups FG
Class I Zone 0, Ex/AEx ia [ia] IIC
T4 Ga
Class I Zone 2, Ex/AEx ic [ic] IIC T4
Gc
7/12
Page 8
SCOUT220-IS and SCOUT240-IS Portable Data Collectors
Datasheet 109M0226 Rev. P
Cyber Security
The SCOUT220-IS and SCOUT240IS solutions
include an industrial handheld device that runs
the Android operating system and uses USB,
cellular, Bluetooth and Wi-Fi for
communication. These solutions have features
that reduce but do not eliminate cyber security
risks.
We strongly recommend implementing
additional cyber security protections such as:
n Controlling user access
n Scanning for viruses
n Applying timely updates
n Using mobile devicemanagement
software
The recommended measures are at
your discretion and responsibility. Some
residual risk may remain.
For details, see the SCOUT200 Series Cyber
Security Hardening Guideline (document
131M1304) at BNTechSupport.com.
8/12
Page 9
SCOUT220-IS and SCOUT240-IS Portable Data Collectors
Datasheet 109M0226 Rev. P
Part Number Description Qty
Ordering Information
For the detailed listing of country and
product specific approvals, refer to the
Approvals Quick Reference Guide
(108M1756) available from
BNTechSupport.com.
SCOUT220IS-AA
A: Data Collector Approval Options
05 Multi Approvals (CSA, IECEx, ATEX)
The SCOUT220-IS basic kit does
NOTinclude a handheld device, nor a
System 1 software license. They are
ordered separately under Optional
Accessories below.
Part Number Description Qty
S1 Collector app
SCOUT220-IS Data
Collector
108M4044
109M2382
PLUS0230 Category A power
PLSA0241 Category D power
AC power adapter
DC car adapter
plug (USA / Canada)
plug (South Africa /
India)
200350*
138M7749 Transducer cable, 4 ft.
113M5585 Accelerometer
109M2385-012
110M8172-012
109M2384-01 Anti-static neck strap
112M4551 Hard carrying case 1
109M1269
1
1
1
1
1
1
109M1270-01
Bently_
Manuals DVD
side or top exit
straight
magnetic base
BNC to silver-LEMO
cable. Connects rack
buffered outputs to
CH1/CH2 inputs.
BNCto black-LEMO
cable.
Connects rack
buffered Keyphasor to
Tach input.
with Sensor Keeper
SCOUT200 Series User
Guide
SCOUT200 Series
Quick Start Guide
Contains the
SCOUT220IS and
SCOUT240ISProduct
Datasheet
(109M0226), the
SCOUT200 Series
Quick Start Guide
(109M1270), and the
SCOUT200 Series User
Guide (109M1269).
2
2
2
1
1
1
1
1
PLAU0228 Category M power
plug (Australia / New
Zealand / China)
PLHK0245 Category G power
plug (Hong Kong / UK)
PLEU0229 Category C Power
plug (Europe)
109M2381 or
200350*
ACCL0561 or
Accelerometer,
top exit
Accelerometer,
1
* Kit items with multiple part numbers listed
have limited regional availability due to
certification requirements.
1
The overallhazardous system rating is
defined by the minimum rating of the
1
data collector, industrial handheld, and
accessories.
1
To request metrology calibration,
contact www.BNTechsupport.com.
1
9/12
Page 10
SCOUT220-IS and SCOUT240-IS Portable Data Collectors
Datasheet 109M0226 Rev. P
SCOUT240IS-AA
A: Data Collector Approval Options
05 Multi Approvals (CSA, IECEx, ATEX)
The SCOUT240IS basic kit does
NOTinclude a handheld device, nor a
System 1 software license. They are
ordered separately under Optional
Accessories below.
Part Number Description Qty
S1 Collector app
SCOUT240IS Data
Collector
108M4044
109M2382
PLUS0230
PLSA0241
PLAU0228
PLHK0245
PLEU0229
109M2381 or
200350*
ACCL0561 or
200350*
138M7749
113M5585
AC power adapter
DC car adapter
Category A power
plug (USA / Canada)
Category D power
plug (South Africa /
India)
Category M power
plug (Australia / New
Zealand / China)
Category G power
plug (Hong Kong / UK)
Category C Power
plug (Europe)
Accelerometer,
top exit
Accelerometer,
side or top exit
Transducer cable, 4 ft.
straight
Accelerometer
magnetic base
Part Number Description Qty
cable. Connects rack
buffered outputs to
CH1/CH2 inputs.
110M8172-012
BNCto black-LEMO
1
cable.
Connects rack
buffered Keyphasor to
Tach input.
113M9350
Channel 2-4
1
breakoutcable
1
109M2384-01
1
112M4551
1
109M1269
1
109M1270-01
1
Bently_
1
Manuals DVD
Anti-static neck strap
with Sensor Keeper
Hard carrying case
SCOUT200 Series User
Guide
SCOUT200 Series
Quick Start Guide
Contains the
SCOUT220IS and
1
1
1
1
1
SCOUT240ISProduct
Datasheet
(109M0226), the
1
SCOUT200 Series
Quick Start Guide
(109M1270), and the
1
SCOUT200 Series
User Guide
(109M1269).
1
* Kit items with multiple part numbers listed
have limited regional availability due to
3
certification requirements.
The overallhazardous system rating is
1
defined by the minimum rating of the
data collector, industrial handheld, and
4
accessories.
To request metrology calibration,
4
contact www.BNTechSupport.com.
109M2385-012
BNC to silver-LEMO
2
10/12
Page 11
SCOUT220-IS and SCOUT240-IS Portable Data Collectors
Datasheet 109M0226 Rev. P
Optional Accessories
Hand Held Devices
146M8212-01 Smart-Ex 02 DZ2
(North America & Europe)
146M8216-01 Smart-Ex 02 DZ1
(North America & Europe)
To obtain a handheld device suitable
for a location not listed above, contact
a handheld devicedistributor within
the destination country.
Other Accessories
3071/01 System 1 software and license
109M2387 Handheld, battery-powered
laser tach for IS zone 0. Order
cable separately.
109M2389 5-meter laser Tach cable for
109M2387
Language Specific Warning Labels
110M9913 Magnet base label
110M9914 Sensor keeper side label
110M9915 Sensor keeper front label
111M7144 Hard carrying case label
108M4069 Laser Tach powered by
SCOUT220-IS and SCOUT240IS, for Zone 2.
Order cable separately.
CBL50216
122M9408
125M2099-01 Cable for CSLS laser, 1.5m
113M5529-01 Reflectivetape
VBMR0222 Pair of safety rings for
5-meter laser Tach cable for
108M4069.
Monarch Compact Smart
Laser Sensor (CSLS). Higher
powered (3 mW) but larger
size (2.6" x 2.4" x 2") and no
Zone rating. Order cable
separately.
One roll, 60 cm (23.7 in)
attaching strap to data
collector.
11/12
Page 12
SCOUT220-IS and SCOUT240-IS Portable Data Collectors
Datasheet 109M0226 Rev. P
Copyright 2020 Baker Hughes Company. All rights reserved.
Bently Nevada, Orbit Logo and SCOUT are registered trademarks of Bently Nevada, a Baker Hughes Business, in the
United States and other countries. The Baker Hughes logo is a trademark of Baker Hughes Company. All other
product and company names are trademarks of their respective holders. Use of the trademarks does not imply any
affiliation with or endorsement by the respective holders.
Baker Hughes provides this information on an “as is” basis for general information purposes. Baker Hughes does not
make any representation as to the accuracy or completeness of the information and makes no warranties of any
kind, specific, implied or oral, to the fullest extent permissible by law, including those of merchantability and fitness
for a particular purpose or use. Baker Hughes hereby disclaims any and all liability for any direct, indirect,
consequential or special damages, claims for lost profits, or third party claims arising from the use of the
information, whether a claim is asserted in contract, tort, or otherwise. Baker Hughes reserves the right to make
changes in specifications and features shown herein, or discontinue the product described at any time without
notice or obligation. Contact your Baker Hughes representative for the most current information.
The information contained in this document is the property of BakerHughes and its affiliates; and is subject to
change without prior notice. It is being supplied as a service to our customers and may not be altered or its content
repackaged without the express written consent of Baker Hughes. This product or associated products may be
covered by one or more patents. See Bently.com/legal.
1631 Bently Parkway South, Minden, Nevada USA 89423
Phone: 1.775.782.3611 or 1.800.227.5514(US only)
Bently.com
12/12
Loading...