Beninca DAAX User Manual

DA.AX

CENTRALINA A MICROPROCESSORE

CONTROL UNIT WITH MICROCONTROLLER

MIKROCONTROLLER-STEUERUNG

CENTRALE A MICROCONTRÔLEUR

CENTRALITA A MICROPROCESADOR

AUTOMATISMI PER CANCELLI

®

L8542605
Rev. 07/00/01

Libro istruzioni

Operating instructions

Betriebsanleitung

Livret d’instructions

Libro de instrucciones

UNIONE NAZIONALE COSTRUTTORI

AUTOMATISMI PER CANCELLI, PORTE,

SERRANDE ED AFFINI

A

Z

I

E

N

D

A

C

E

R

T

I

F

I

C

A

T

A

UNI

EN IS O

9001

2

Dichiarazione CE di conformità Déclaration CE de conformité

EC declaration of confirmity Declaracion CE de conformidad

EG-Konformitatserklarung

Con la presente dichiariamo che il nostro prodotto

We hereby declare that our product

Hiermit erklaren wir, dass unser Produkt
Nous déclarons par la présente que notre produit
Por la presente declaramos que nuestro producto

DA.AX

è conforme alle seguenti disposizioni pertinenti:
complies with the following relevant provisions:

folgenden einschlagigen Bestimmungen entspricht:

correspond aux dispositions pertinentes suivantes:

satisface las disposiciones pertinentes siguientes:

Direttiva sulla compatibilità elettromagnetica (89/336/
CCE, 93/68/CEE)
EMC guidelines (89/336/EEC, 93/68/EEC)
EMV-Richtlinie (89/336/EWG, 93/68/EWG)
Directive EMV (89/336/CCE, 93/68/CEE) (Compatibilité
électromagnétique)
Reglamento de compatibilidad electromagnética (89/336/
MCE, 93/68/MCE)

Norme armonizzate applicate in particolare:
Applied harmonized standards, in particular:
Angewendete harmonisierte Normen, insbesondere:
Normes harmonisée utilisées, notamment:
Normas armonizadas utilzadas particularmente:

EN 55022, EN 61000-3-2, EN 61000-3-3, EN 50082-1

Norme e specifiche tecniche nazionali applicate in
particolare:
Applied national technical standards and specifications, in
particular:
Angewendete nationale Normen und technische
Spezifikationen, insbesondere:
Normes et specifications techniques nationales qui ont été
utilisées, notamment:
Normas y especificaciones técnicas nacionales que se
utilizaron particularmente:

UNI 8612

Data/Firma

Direttiva sulla bassa tensione (73/23/CEE, 93/68/CEE)
Low voltage guidelines (73/23/EEC, 93/68/EEC)
Tiefe Spannung Richtlinie (73/23/EWG, 93/68/EWG)
Directive bas voltage (73/23/CEE, 93/68/CEE)
Reglamento de bajo Voltaje (73/23/MCE, 93/68/MCE)

Norme armonizzate applicate in particolare:
Applied harmonized standards, in particular:
Angewendete harmonisierte Normen, insbesondere:
Normes harmonisée utilisées, notamment:
Normas armonizadas utilzadas particularmente:

EN 60204-1, EN 60335-1

Data/Firma

AUTOMATISMI PER CANCELLI

®

Automatismi Benincà Srl
Via Scamozzi, 3
36030 MONTECCHIO P. VI
ITALIA

3

TRF1

FF1

FF1

VDR2

R18

D1

TCA

FF4

J1

J3

INPUT

230VAC

M

ANT.

OUT

24VAC

+V

FTC

FCA

FCC

P.P.

CHIUDE

1

F N

COM. APRE CHIUDE

2 3 4 5 6 7 8 9 10 11 12 13 14 15

J2

FF3

DA.AX

SW1

C15

v1.0

X1

R21

R19

R1

R2

R20

R3

C1

U6 U4

U3

C9

C2

C8

R28

D2

6.3A

VDR1 VDR3

RL1

COMUNE

RL2

APRE

RL3

CHIUDE

VDR4

POWER

+
C3

1 Funz. P.P.
2 Rich. Aut.
3 Funz. Cond.
4 P.P./Apre

+
C6

C10

Q2

Q1

U1

U2

R8 R6

R7

R9

+

TL

250mA

F2

C4

R5

R4

R23

C5

C7

C13

R15

R11

R16

R12

R17

R13

R14

R10

Z5Z1Z2

Z3

C12

C11

C14

R22

Z4

FUSE

F1

FUSE

6

DA.AX Control unit with microcontroller

The microprocessor control unit “DA.AX” can be used with motors having a power not exceeding 500W.

Installation instructions.

a) The electrical installation and functioning logic must comply with current standards.

b) It is advisable to keep the power cables (motor, power supply) detached from the control cables

(push-buttons, photocells, radio). In order to avoid any possible interference it is recommended
to provide for and use two separate sheaths (see EN 60204-1 15.1.3).

c) Before powering the unit, check again all connections which have been carried out.

d) Check the correct presettings of the Dip-Switches.

e) When the unit is powered, the LED “POWER” must be lit; in the negative, check fuses and that

230Vac 50Hz power supply is present between terminals 1 and 2 (INPUT 230VAC - keep to
phase / neutral).

f) The N.C. inputs not used must be connected to the common “+V”.

g) Should the direction of rotation of the motor be reversed, invert the motor wires “OPEN” with

“CLOSE” and the limit switches wires “FCA” with “FCC”.

Input/Output functions

(1,2) INPUT 230VAC= Control unit 230Vac 50 Hz power supply

(respect phase/neutral wire position).

(3,4,5) COM/APRE/CHIUDE= Connection to the corresponding 230Vac 50 Hz motor terminals

(the earth wire (green/yellow) must be connected to the motor housing).

(6,7) OUT 24VAC= 24Vac auxiliary power supply output (100mA max.).

(12) +V= Common connection to all the control inputs.

(9) FTC= Photocell receiver input (n.c. contact).

(10) FCA= Input of limit switch APRE (n.c. contact).

(11) FCC= Input of limit switch CHIUDE (n.c. contact).

(8) P.P.= Input, “PASSO-PASSO” push button or “APRE” push-button according to the Dip-Switch

presetting

(15) CHIUDE= CLOSE button input (n.o. contact).

(13,14) ANT.= Input of radio board antenna

Dip-switch functions

N.B.: Every change of functions have to be done without electricity.

DSW1= This selects the type of functioning of the P.P. button and Remote control.

Off= ”APRE” - ”STOP” - ”CHIUDE” functioning
On= ”APRE” - ”CHIUDE” - ”APRE” functioning.

DSW2= This enables or disables the automatic re-closing - ”TCA TRIMMER”.

Off= Automatic re-closing enabled
On= Automatic re-closing disabled

DSW3= This enables or disables the apartment building function (after the first opening command, the

P.P. button and the Remote control are deactivated).

7

Off= Apartment building function disabled.
On= Apartment building function enabled.

DSW4= It selects the operation of the “P.P.” input as push-button “PASSO-PASSO” or push-button

“APRE”.
Off= “P.P.” push-button
On= “APRE” push-button

Trimmer functions

TCA= This allows the automatic re-closing time to be adjusted when this is enabled by positioning the

DSW2 Dip-switch on OFF.
Adjustment can be from a minimum of 5 to a maximum of 150 seconds.
The minimum time is obtained by rotating the trimmer completely clockwise.

TL= This allows the working time of the automation to be adjusted. If the limit switches fail, the soft-

ware protection will intervene after this time has elapsed. (Add about 4 sec. to the actual stroke
time of the automation).
Adjustment can be from a minimum of 7 to a maximum of 180 seconds.
The minimum time is obtained by rotating the trimmer completely clockwise.

Note

• The ”STOP” control can be carried out by connecting the normally closed push button between the
common wire of the limit switch and the ”+V” terminal (see drawing).

• If the ”P.P.” input is used as ”APRE” (Dip-switch 4= ON), the automatic closure is not carried out until
the contact remains closed.

+V

FTC

FCA

FCC

STOP button

Limit switch buttons

AUTOMATISMI PER CA NCELLI

®

AUTOMATISMI BENINCÀ Srl - Via Capitello, 45 - 36066 Sandrigo (VI) - Tel. [phone] r.a. - Fax [phone]