PVS-4207T
1
x
Ordering part #
CHFE 003
Sheet nr.
ALLEN KEY
4
x
O
rdering part #
M80100
Item #
7
5
x
Ordering part #
M80016
I
tem #
8
M
8*16
M8*100
1
0 x
O
rdering part #
MP00022
Item #
1
0
4 x
Ordering part #
FVPL 006
Sheet nr.
1
1
2
x
O
rdering part #
M80030
I
tem #
15
M
8*30
Glass Pad
M
15
8
1
3
5
11
1
2
7
16
11
6
4L
10
4R
8
8
8
8
2
3
1
10
10
8
15
7
ASSEMBLY INSTRUCTIONS
OTE: 2 People are recommended to assemble this furniture.
N
Bell’O International Corp.
711 Ginesi Drive
Morganville, NJ 07751-1235
Customer Service: (888) 235-7646
E-mail: support@bello.com
Web: www.bello.com
TANDthe rear CMS
. S
A
®
Cable Management System) frame (1)
(
upright so that it is resting on the floor. NOTE: The TOP of the
CMS®frame has two cut outs that should be facing up.
B. ALIGN the bottom shelf frame (2) with the bolt holes located in
he bottom rear of the CMS
t
®
rame (1) and ATTACHusing the
f
long bolts (7) and the supplied Allen key. DO NOT TIGHTEN
ULLY.
F
.
LIGNthe middle shelf frame (3) with the bolt holes located in
C
A
the middle rear CMS
olts (7) and the supplied Allen key. DO NOT TIGHTEN FULLY.
b
LIDEthe inserts that are located on the edges of the two
D.S
®
frame (1) and ATTACH using the long
upright legs (4L and 4R) into the open ends of the bottom
helf frame (2) and the middle shelf frame (3) and attach with
s
the smaller bolts (8) using the supplied Allen key.
NOTE: The legs are in the proper position when the angled inserts
14) are at the bottom of the leg and facing forwards as shown in
(
Fig. 2
ALIGN the top shelf frame (16) with the bolt holes located in
E.
he top rear of the CMS
t
®
rame (1). ALIGNthe top frame
f
metal plate (13), with the screw holes located in the top
ear CMS frame (1) and attach from the rear with two
r
middle size bolts (15) and one of the smaller bolts (8)
n the middle as shown in Fig. 3. FULLY TIGHTEN
i
THE BOL
TS using the supplied Allen key. This metal
plate will function as a retainer for the top glass shelf.
NOW GO BACK AND FULLY TIGHTEN ALL BOLTS, making
.
F
sure those described in Steps B and C are now secure.
NOTE:
MOVE the table to the location that it will occupy in the
om when fully assembled and in use, PRIOR to placing the
o
r
glass shelves.
G.
APPLYthe glass pads (10) to the bottom, middle and top
frames as shown in Fig. 1. CAREFULLY place the bottom glass
shelf (6) onto the frame. The curved edge of the glass should
be facing forward. NOTE: The bottom glass shelf is not as wide
FIG.1
as the other two.
INSERT two plastic suction cups (11) into the holes in the mid-
H.
dle shelf frame (3) and push into place.
AND PLACE
the middle glass shelf (12) onto the middle shelf
frame and GENTLY push downwar
ved edge should be facing forward. NOTE: The middle glass
cur
CAREFULLY CENTER
eate a seal. The
d to cr
shelf is the deepest of the three shelves.
NOTE: The suction cups are intended to limit the movement of the
middle shelf and prevent easy shelf removal. To release the seal,
gently pull down on edge of the suction cups.
PLACE two plastic suction cups (11) into the holes in the top
I.
shelf support frame (1) and push into place.
J. CAREFULLY angle the top glass shelf (5) slightly upwards, and
slide it into the metal plate (13) on the top of the CMS frame
FIG.2
(1) as shown in Fig. 4, making sure that the curved edge of the
CAREFULLYcenter the top glass shelf
glass is facing for
ward.
(5) over the top shelf support frame (1), then lower it GENTLY,
pushing downward to create a seal.
NOTE: The top glass shelf is the narrowest of the three shelves.
IMPORTANT: REMOVE ALL GLASS, TV AND OTHER EQUIPMENT
FROM THE FURNITURE PRIOR TO MOVING THE ASSEMBLED
UNIT. DO NOT ATTEMPT TO MOVE THE ASSEMBLED FURNITURE
FIG. 3
AFTER THE GLASS SHELVES HAVE BEEN INSTALLED, AND/OR
WHEN THERE IS EQUIPMENT LOCA
MAKE SURE THA
T THE FRONT OF THE TV IS POSITIONED A FEW
TED ON THE FURNITURE.
INCHES BACK FROM THE FRONT OF THE TOP GLASS. WHEN IN
USE, THIS FURNITURE MUST BE PLACED ON A FLAT, SOLID,
AND LEVEL SURFACE. DO NOT LEAN ON THE TV WHEN IT IS ON
THE TV STAND. DO NOT CLIMB OR STEP ON THE STAND. DO
NOT BANG OR PLACE YOUR OWN WEIGHT ON THE GLASS
VES.
FIG. 4
SHEL
ALWAYS PLACE THE HEAVIEST EQUIPMENT ON THE BOTTOM
SHELF.
ITALIAN DESIGNED PATENT NO. 505,573
Bell’O International Corp. will not be responsible for failure to assemble as directed or for the improper assembly, use or handling of this stand. © 2006 BELL’O INTERNATIONAL CORP.
Loading...