Behringer UM300 User Manual

ULTRA METAL UM300

◊

◊

(3)

(1)

(5)

(4)

(7)

(2)

(8)

(6)

(9)

Heavy Met al Distortio n E e cts Pedal

Thank you for showing your con dence in us by purchasing the BEHRINGER ULTRA METAL UM300.
This high-quality e ects pedal comes with a dual- gain circuitry that enables you to produce super thick,
tube-like dis tortion plus endless sustain. Thanks to its high-performance features you will achieve the
most extreme and sought-after hard rock or heavy metal distor tion sounds.

1. Controls

(1) The LOW control allows yu to boost/cut the lo -frequency range.

◊ Please keep in mind that ex trme distortion and EQ set tings will increase nose and may

induce oscillation.

(2) The two MID FREQ(uency) controls allow to boost/cut a de ned mid-frequency range. The upper

control is used to increase or lower the mid range, the cntrol below adjusts the center frequenc y of
the mid range that is a ected (200 Hz to 5 kHz).

(3) The LEVEL control adjusts the out put level.

(4) The ON/BATT LED illumnates when the e ect is activated. It also serves as a bat tery leve indicator.

(5) Use the footswitch to ac tivate/deactivate the e ect.

(6) Use this ¼" TS IN connector to plug in the instrument cable.

(7) The ¼" TS OUT connector sends the signal to your amp.

Use the DC IN connectionto plug in a 9 V power supply (not included).

The BATTERY COMPARTMENT is located underne ath the pedal cover. To install or replace the 9 V bat tery,
press the hing es with a ballpen and remove the pe dal cover. B e careful not to scratch t he unit.

◊ The UM300 has no on/o switch. As soon as you insert the jack into the in connector,

the UM300 begins running. When not using the UM300, remove the jack f rom the
in connec tor. This extends the life of the battery.

The SERIAL NUMBER is located at the bot tom.

ULTRA METAL UM300

2. Safety Instructions

Do not use near water, or inst all near heat sources. Use only authorized attachments/accessories.
Do not service produc t yourself. Contact our quali ed servicing p ersonnel for servicing or repairs,
especially when power supply cord or plug is damaged.

3. Warranty

Please register your new BEHRINGER equipment r ight after your purchase by visiting
http://behringer.com and read the terms and conditions of our war ranty carefully.

4. Speci cations

In

Connector ¼ " TS

Impedanc e 500 kΩ

Out

Connector ¼ " TS

Impedanc e 1 kΩ

Power Supply

9 V𝌂, 100 mA r egulated

BEHRINGER PSU-SB

USA/Canada 120 V~, 6 0 Hz

U.K./Austra lia 240 V~, 50 Hz

China/Ko rea 220 V~, 50 Hz

Europe 230 V~, 50 Hz

Japan 100 V~, 50 - 60 Hz

Power connec tor 2 mm DC jack,
negative center

Batter y 9 V type 6LR 61

Power consumpt ion 30 mA

Physical/Weight

Dimensio ns approx. 54 x 70 x 123 mm
(H x W x D) (2.1 x 2.8 x 4.8")

Weight appr ox. 0.33 kg (0.7 lbs)

BEHRING ER is constant ly strivin g to maintain the
highes t professio nal standard s. As a result of t hese eff orts,
modif ications may b e made from tim e to time to exis ting
produc ts withou t prior notice . Specific ations and app earance
may there fore diff er from thos e listed or show n.

MUSIC Group accepts no liability for any loss which may be su ered by any person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical speci cations, appearances and other information are subject to change without notice. All trademarks are the property
of their respective owners. MIDAS, KLARK TEKNIK, TURBOSOUND, BEHRINGER, BUGERA and DDA are trademarks or registered trademarks of MUSIC Group IP Ltd.
© MUSIC Group IP Ltd. 2015 All rights reserved.