Behringer NR300 User Manual
NOISE REDUCER NR300
Thank you for showing your confidence in us by purchasing the BEHRINGER NOISE
REDUCER NR300. This ultimate effects pedal is specifically designed to eliminate unwanted
noise and hum without altering your tone. Thanks to its high-performance features it
preserves the original attack and envelope while leaving your playing and dynamics intact.
1. CONTROLS
Top view
This MODE switch allows you to chose between MUTE and REDUCTION mode.
Pressing the pedal in MUTE mode results in muting the whole input signal, to reduce
noises in during pauses for example. In REDUCTION mode, quiet passages (when
noise or hum would get obvious to the listener) are effectively reduced. Adjustments
to threshold and decay settings are necessary in this case (see below).
Use the THRESH(old) control to define a level threshold in REDUCTION mode.
When the input signal falls below this value, the unit starts reducing the signal.
The DECAY control determines how fast the signal reduction is released when the
input signal exceeds the threshold value again.
The MUTE/BATT LED illuminates when the effect is activated. It also serves as a
battery level indicator.
The REDUCTION LED illuminates when the input level falls below the threshold
and starts getting reduced.
Use the footswitch to activate/deactivate the effect.
Use this 1/4" TS IN connector to plug in the instrument cable.
The 1/4" TS OUT connector sends the signal to your amp.
Use this 1/4" TS SEND connector to connect it to the input of an external effect unit. This
way you can feed in an effect signal while simultaneously eliminating noises from the unit.
The 1/4" TS RETURN connector is used to feed in the external effect signal.
Use the DC IN connection at the front of the unit to plug in a 9 V power supply (not included).
The BATTERY COMPARTMENT is located underneath the pedal cover. To install or
replace the 9 V battery, press the hinges with a ballpen and remove the pedal cover. Be
careful not to scratch the unit.
+ The NR300 has no on/off switch. As soon as you insert the jack into the IN
connector, the NR300 begins running. When not using the NR300, remove
the jack from the IN connector. This extends the life of the battery.
The SERIAL NUMBER is located at the bottom.
NOISE REDUCER NR300
2. WARRANTY
For our current warranty terms, please refer to our website at http://www.behringer.com.
3. SPECIFICATIONS
In
Connector 1/4" TS
Impedance 500 kW
Out
Connector 1/4" TS
Impedance 1 kW
Send
Connector 1/4" TS
Impedance 1 kW
Return
Connector 1/4" TS
Impedance 50 kW
Power supply 9 V , 100 mA regulated
Power connector 2 mm DC jack, negative center
Battery 9 V type 6LR61
Power consumption 30 mA
Dimensions (H x W x D) approx. 54 mm (2 1/8") x 70 mm (2 3/4") x 123 mm (4 4/5")
Weight approx. 0.33 kg (0.73 lbs)
BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made
from time to time to existing products without prior notice. Specifications and appearance may therefore differ from those list ed or shown.
BEHRINGER PSU-SB
USA/Canada 120 V~, 60 Hz
China/Korea 220 V~, 50 Hz
U.K./Australia 240 V~, 50 Hz
Europe 230 V~, 50 Hz
Japan 100 V~, 50 - 60 Hz
Do not use near water, or install near heat sources. Use only authorized attachments/accessories. Do not service product yourself.
4. SAFETY INSTRUCTIONS
Contact our qualified servicing personnel for servicing or repairs, especially when power supply cord or plug is damaged.
No utilizar cerca de agua o instalar cerca de fuentes de calor. Utilice sólo accesorios y aditamentos autorizados. No intenté reparar
el producto usted mismo. Contacte a nuestro personal técnico cualificado para servicio y reparaciones, especialmente cuando la
fuente o el cable de alimentación estén dañados.
Íåэксплуатируйтеприбор вблизи îò источниковâîäûè тепла. Применяйте только авторизованные дополнительные
óстройства.Íèêîãäàíå ремонтирóéòåприбор самостоятельно. Ðемонтìîæåò произвоäèòüòîëüêîквалифицированный
специализированныйперсонал,
Die deutsche Anleitung ist erhältlich @ www.behringer.com
Manuel francophone en téléchargement sur www.behringer.com
Manual en español disponible en www.behringer.com
Manuali italiani disponibili @ www.behringer.com
Ðóññê оязычноеðóêîâîдство@www.behringer.com
Polskainstrukcjadostêpnajestpodadresem@ www.behringer.com
Nederlandse handleiding beschikbaar @ www.behringer.com
Suomenkielinen käyttöohje saatavilla osoitteesta www.behringer.com
Svensk manual finns tillgänglig på www.behringer.com
Dansk vejledning findes på @ www.behringer.com
Manual português disponível @ www.behringer.com
Еллзнйкь егчейсЯдйп хрЬсчей дйбиЭуймп уфз дйеэихнуз www.behringer.com
Technical specifications and appearance subject to change without notice. The information contained herein is correct at the time
of printing. The names of companies, institutions or publications pictured or mentioned and their respective logos are registered
trademarks of their respective owners. Their use neither constitutes a claim of the trademarks by BEHRINGER nor affiliation of the
trademark owners with BEHRINGER. BEHRINGER accepts no liability for any loss which may be suffered by any person who relies
either wholly or in part upon any description, photograph or statement contained herein. Colors and specification may vary slightly from
product. Products are sold through our authorized dealers only. Distributors and dealers are not agents of BEHRINGER and have
absolutely no authority to bind BEHRINGER by any express or implied undertaking or representation. No part of this manual may be
reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind,
for any purpose, without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH. BEHRINGER® is a registered
trademark. ALL RIGHTS RESERVED. © 2006 BEHRINGER Spezielle Studiotechnik GmbH, Hanns-Martin-Schleyer-Str. 36-38, 47877
Willich-Münchheide II, Germany. Tel. +49 2154 9206 0, Fax +49 2154 9206 4903
особенноïðèповреждениях сетевого провода èëèсетевойвилки.
Loading...