Behringer EPX2000, EPX3000 BROCHURE

EPX2000/EPX3000

Power Amplifi ers

Power Amps

EPX3000: 2 x 1500 Watts into 2 Ohms;
2 x 900 Watts into 4 Ohms; 3000 Watts
into 4 Ohms (bridge mode)

EPX2000: 2 x 1000 Watts into 2 Ohms;
2 x 650 Watts into 4 Ohms; 2000 Watts
into 4 Ohms (bridge mode)

ATR (Accelerated Transient Response)
technology for ultimate punch
and clarity

Ultra-light, ultra-low noise and ultra­effi cient switch-mode power supply
for noise-free audio, superior transient
response and low power consumption

Switchable limiters off er maximum
output level with reliable overload
protection

Detented gain controls for precise
setting and matching of sensitivity

Precise Power, Signal and Clip LEDs to
monitor performance

XLR, /" TRS and RCA input connectors
for compatibility with any source

Professional speaker connectors and
“touch-proof” binding posts support
most speaker wiring systems

Built-in Subwoofer/Satellite crossover
for more fl exibility

Independent DC and thermal overload
protection on each channel automati­cally protects amplifi er and speakers
without shutting down the show

“Back-to-front” ventilation system
including air fi lter for reliable
operation

“Built-like-a-tank”, impact-resistant,
all-steel 2U rackmount chassis

High-quality components and
exceptionally rugged construction
ensure long life

Conceived and designed by
BEHRINGER Germany

EUROPOWER — Professional 3000/2000-Watt Light
Weight Stereo Power Amplifi ers with ATR
(Accelerated Transient Response) Technology

Ultra-light, built on a legacy

Power amps have always been
heavy, mainly because of the massive
transformers and huge banks of capacitors
needed for high-power operation. In fact,
six conventional power amps in a rack can
easily top 250 pounds. The same number
of EPX Series amps come in at just under
134 lbs./61 kg, and they pack all the power
of their conventional counterparts!”

In a class of their own

The secret to the EPX series’ incredible
power-to-weight ratio is their use of a
switching-mode power supply combined
with Class-H topology. Switching-mode
power supplies work on demand. Instead
of constantly working at full power

and dissipating excess power as heat,
they only ramp up the power output
when needed—thousands of times per
second. Considerably more effi cient than
traditional power supplies, switching­mode power supplies are small and light,
yet deliver ample power.

Think of a Class H amp as a car with two
engines (in amps, you call them “rails”).
One engine runs all the time. The other
runs only when musical peaks demand
extra power output. An EPX Class H amp
only generates a fraction more power than
is immediately needed while the output
stage operates at its maximum effi ciency
all the time.

Continued on next page

behringer.com

EPX2000/EPX3000

Power Amps

And just like in today’s hybrid cars, the effi ciency
of this dual system is far greater than having one
engine or rail that must operate all the time. EPX
amps don’t waste power. Class H amps don’t waste
power, require much smaller heat sinks and much
lighter power transformers.

Accelerated Transient Response delivers the
knock-out punch

It takes huge pulses of energy (current and
voltage) to propel a woofer cone out fast enough to
match a bass beat. That’s called Transient Response
and it’s the holy grail of amp designers. By carefully
selecting transistors with extremely high slew
rates and optimizing other proprietary parts of our
circuitry, our amps are able to react instantly to even
the most demanding electronic bass impulses. If
the woofers in your PA system can keep up, your
audience will hear a tighter, crisper, more natural
sound.

Instead of operating relatively continuously
like Class AB circuits, Class H amps, which were
fi rst described in NASA technology (U.S. patent
3,319,175), feature rail tracking for eff ectively
modulating the power supply rails with only the
peaks of the input signal. This technology has
revolutionized pro audio amp designs with its
outstanding performance and effi ciency. When
combined with switching-mode power supplies that
replace heavy toroid transformers, our new designs
provide more dynamic punch and, because they are
so much more effi cient, run cooler and don’t require
huge, heavy heat sinks.

BEHRINGER didn’t invent Class H technology, but
our R&D Department has been working for years
to perfect our own version, creating lightweight
amps that run cool and also achieve our goal of
Accelerated Transient Response.

Everything you need, nothing you don’t

The simple front panel controls of these amps
give you all of your sound’s vital signs at a glance.
After pressing the Power Button, the POWER LED
will light when the amp is ready for action. Both
channels have independent gain dials as well as
clip LEDs that indicate when the signal is distorted
and you need to reduce the gain. There are also
SIGNAL LEDs that light up when a signal is present
at the input.

Continued on next page

IEC power socket.

Stereo Out

Input
Channel 1

Input Channel 2

Mono Out

Input
Channel 1

Professional locking
speaker connections.

R

L

EUROPOWER EPX3000

Mixing Console

EUROPOWER EPX3000

(MONO MODE)

Power On/Off
Switcher

0

-10

-20

Signal level
LED meter with
clipping LED.

“Touch-proof” binding
posts speaker outputs.

Cooling fans.

Stereo Mode

SX2442FX

Mixing Console

(STEREO MODE)

Mono Mode

SX2442FX

0

-10

-20

3000-WATT STEREO POWER AMPLIFIER

Detented channel
GAIN controls.

3000-WATT STEREO POWER AMPLIFIER

Ventilation
openings.

MODE switch —
mono/stereo/bridge.

Built-in CROSSOVER
switch — dedicated
100 Hz CH1/CH2 or
FULLRANGE.

INPUT accepts balanced XLR,

1

/4" TRS, and unbalanced

1

/4" TS and RCA connections.

LIMITER on/off switch.

EUROLIVE B1520 PRO

Full range loudspeaker

EUROLIVE B1520 PRO

Full range loudspeaker

Page 2 of 4

EPX2000/EPX3000

Page 3 of 4

Power Amps

Panel discussion

The EPX series’ INPUTs accept balanced XLR,

1

/4" TRS, and unbalanced 1/4" TS and RCA
connections. Take your pick of professional locking
speaker outputs or touch-proof binding posts to
securely connect speakers.

A panel of switches found on the back off ers an
array of cool options applicable to both channels.
The Clip Limiter lets you get even more out of
the amplifi er without overdriving either it or your
speaker system. Built-in circuitry automatically
senses when the amp is being overdriven into
“clipping” and then momentarily reduces the input
level to avoid clipping distortion. This all happens in
a few thousandths of a second, so it’s an inaudible
way of avoiding audible clipping distortion. Of
course, you can turn the Limiter off if you’re
feeling lucky.

The same panel contains the switches that
allow you to put these amps to work in either
mono, stereo (two-channel mode) or bridge mode,
which is always in mono. A built-in CROSSOVER
switch lets you select the point at which highs and
lows are separated (CH1<100Hz / CH2>100 Hz or
FULLRANGE).

BEHRINGER’s EPX line is built for the working
musician. It’s much easier to transport than a
conventional AB power amp, it packs ample power,
it’s got a built-in crossover and limiter, and it’s built
to last through all the rigors of the road. Plus its light
price tag will leave you with enough cash left over to
acquire more stuff to amplify! Check out an EPX and
fi nd out why BEHRINGER power amps are among
the most popular on Earth.

EUROPOWER EPX3000
(STEREO MODE)

EUROLIVE
B1520 PRO
Full range
loudspeaker

Bi-Amp Mode

Mixing Console

SX2442FX

L

R

Stereo Out

EUROPOWER EPX3000
(STEREO MODE)

EUROLIVE
B1800X-PRO
Subwoofer

EUROLIVE
B1520 PRO
Full range
loudspeaker

EUROLIVE
B1800X-PRO
Subwoofer

EPX2000/EPX3000

Power Amps

Page 4 of 4

Input Voltage

EPX2000/EPX3000 100V - 240V

Stereo Mode (both channels driven)

EPX2000/EPX3000 Continuous average output

power per channel

EPX2000

8Ω / 20 Hz - 20 kHz @ 0.1% THD : 350 W

8Ω / 1kHz @ 0.1% THD : 360 W

4Ω / 20 Hz - 20 kHz @ 0.1% THD : 600 W

4Ω / 1 kHz @ 0.1% THD : 650 W

2Ω / 20 Hz - 20 kHz @ 1% THD : 950 W

2Ω / 1 kHz @ 1% THD : 1000 W

EPX3000

8Ω / 20 Hz - 20 kHz @ 0.1% THD : 500 W

8Ω / 1kHz @ 0.1% THD : 520 W

4Ω / 20 Hz - 20 kHz @ 0.1% THD : 850 W

4Ω / 1 kHz @ 0.1% THD : 900 W

2Ω / 20 Hz - 20 kHz @ 1% THD : 1400 W

2Ω / 1 kHz @ 1% THD : 1500 W

Bridged Mono

EPX2000

8Ω / 20 Hz - 20 kHz @ 0.1% THD : 1200 W

8Ω / 1kHz @ 0.1% THD : 1250 W

4Ω / 20 Hz - 20 kHz @ 1% THD : 1900 W

4Ω / 1 kHz @ 1% THD : 2000 W

EPX3000

8Ω / 20 Hz - 20 kHz @ 0.1% THD : 1700W

8Ω / 1kHz @ 0.1% THD : 1800W

4Ω / 20 Hz - 20 kHz @ 1% THD : 2800W

4Ω / 1 kHz @ 1% THD : 3000W

Distortion

EPX2000/EPX3000 <0.01%

Frequency Response (at 10dB below rated output power)

EPX2000 20Hz - 20kHz, +0/-1 dB

5Hz - 50kHz(at -3dB points)

EPX3000 20Hz - 20kHz, +0/-1 dB

5Hz - 50kHz(at -3dB points)

Damping Factor (1 kHz and below)

EPX2000 >300 @ 8Ω

EPX3000 >400 @ 8Ω

Signal to Noise (20 Hz - 20 kHz)

EPX2000/EPX3000 >100 dB

Voltage Gain

EPX2000/EPX3000 32 dB

Input Sensitivity

EPX2000 1V

EPX3000 1.17V

Input Impedance

EPX2000/EPX3000 10k ohms unbalanced /

20k ohms balanced

Controls

Front: AC switch/ gain controls

for each channel

Rear: MONO Switch, X-Over

Switch, Limiter Switch,
BRIDGE MODE Switch

X-Over FX 100Hz, 12dB slope

Limiter Type

EPX2000/EPX3000 VCA CLIP Limiter,

switchableIndicators

Connectors (each channel)

Input: Active balanced XLR

(pin 2+), ¼" TRS

Output: Touch-proof binding posts /

speaker connectors

Cooling:

EPX2000/EPX3000 Continuously variable speed

Ampli er protection

EPX2000/EPX3000 Full short circuit, open

Load protection

EPX2000/EPX3000 On/o muting, DC-fault

Output Circuitry

EPX2000/EPX3000 Class H, 2-tier

Power consumption

1

/8 Power (pink noise) Bridged 4ohms

EPX2000 5A_230V / 9A_120V

EPX3000 6.5A_230V / 12A_120V

use fuse rating

EPX2000 EU:10A250V/UL:20A250V

EPX3000 EU:15A250V/UL:30A250V

Dimensions

EPX2000/EPX3000 19"/ 2U

Weight

EPX2000/EPX3000 10.10 kg/22.26 lbs.

BEHRINGER is constantly striving to maintain the highest
professional standards. As a result of these e orts, modi cations
may be made from time to time to existing products without prior
notice. Speci cations and appearance may di er from those listed
or illustrated.

fan, back-to-front air  ow

circuit, thermal, ultrasonic,
RF protection. Stable into
reactive or mismatched
loads

power supply shutdown

For service, support or more information contact the BEHRINGER location nearest you:

BEHRINGER Australia tel.: [phone], fax: [phone] BEHRINGER Germany tel.: +49
2154 9206 4149, fax: [phone] BEHRINGER Japan tel.: [phone], fax: [phone]
1181 BEHRINGER Singapore tel.: [phone], fax: [phone] BEHRINGER USA / CANADA
tel.: [phone], fax: [phone]

©2009 Red Chip Company Ltd. Technical specifi cations and appearance subject to change without notice. The information contained herein is correct at the time of printing. BEHRINGER accepts no liability for any loss which may be
suff ered by any person who relies either wholly or in part upon any description, photograph or statement contained herein. All trademarks (except BEHRINGER, the BEHRINGER logo, JUST LISTEN, EUROPOWER and EUROLIVE) mentioned
belong to their respective owners and are not affi liated with BEHRINGER. 985-10000-00408

behringer.com