Behringer 962 Quick Start Guide
Quick Start Guide
962 SEQUENTIAL SWITCH
Legendary Analog CV Multiplexer
Module for Eurorack
Controls
(1)
(2)
(3)
(4)
(5) (6)
(1) TRIGGER OUTPUTS – Sends a t rigger output vi a 3.5 mm
TS cable wh enever the respec tive stage is ac tive.
The adjacen t LED will light to indic ate an active sta ge.
(2 ) TRIGG ER BUTTON – Allows a sta ge to be
manually selected.
(3 ) TRIGG ER INPUTS – Triggers fro m other modules can b e
connec ted via 3.5 mm TS cable to a ctivate speci c stages.
(4 ) SHIFT – A t rigger can be conn ected via 3.5 mm TS c able
to activ ate the next sta ge in the sequence. Wh en using
the 962 to cr eate a 16 or 24-step sequenc er with the 960,
this jack is u sually connecte d to the OUT jack of the 96 0’s
rst st age.
(5 ) SIG IN – O ne of the inputs is ro uted to the OUTPUT jac ks
dependin g on which stage is a ctive. If all 3 input s are used,
the module w ill shift in 3 st ages. If only the r st
2 inputs a re used, the shif t will alternate bet ween stages
1 and 2. These i nputs are usually c onnected to the 9 60’s
output section.
(6 ) OUTPUT – Sen d the output to anoth er module via
3.5 mm TS cabl e.
Power Connection
The module c omes with the requ ired power cable f or connecting
to a standa rd Eurorack power su pply system. Fol low these
steps to con nect power to the mo dule. It is easier to make th ese
connec tions before the m odule has been mou nted into a
rack cas e.
1. Turn the power su pply or rack case p ower o and
disconne ct the power cabl e.
2. Insert the 16- pin connector o n the power cable into t he
socket on t he power supply or rac k case. The connec tor has
a tab that wi ll align with the gap in t he socket, so it can not
be inser ted incorrec tly. If the power supply d oes not have
a keyed socke t, be sure to orient pi n 1 (-12 V) with the red
stripe o n the cable.
3. Insert the 10 -pin connecto r into the socket on th e back of
the module. T he connector has a t ab that will align wi th the
socket for correct orientation.
4. After both en ds of the power cable hav e been securely
attac hed, you may mount the mo dule in a case and
turn on the p ower supply.
Installation
The neces sary screws ar e included with th e module for mount ing
in a Eurorac k case. Connect t he power cable bef ore mounting.
Dependi ng on the rack case, th ere may be a series of x ed holes
spaced 2 HP ap art along the leng th of the case, or a tra ck that
allows indi vidual threaded p lates to slide along th e length of the
case. The f ree-moving th readed plates allow p recise positi oning
of the modu le, but each plate shoul d be positioned in t he
approxim ate relation to the mo unting holes in your m odule
before attaching the screws.
Hold the mo dule against the Eur orack rails so that e ach of the
mounting h oles are aligned wi th a threaded rail o r threaded
plate. Att ach the screws par t way to start, w hich will allow small
adjustments to the positioning while you get them all aligned.
After th e nal position has b een establishe d, tighten the
screws d own.
Specication
Inputs
Signal inputs
Type 3.5 mm jack, DC coupled
Impedance > 50 kΩ, unbalanced
Maximum input level +10 V
Trigger inputs
Type 3.5 mm jack, DC coupled
Impedance > 50 kΩ, unbalanced
Maximum input level +10 V
Trigger operation Active high,
+3.5 V minimum
Shift input
Type 3.5 mm jack, DC coupled
Impedance 10 kΩ, unbalanced
Maximum input level +10 V
Shift operation Active high, +1 V minimum
Outputs
Signal outputs
Type 3.5 mm jack, DC coupled
Impedance 500 Ω, unbalanced
Maximum output level +10 V
Trigger outputs
Type 3.5 mm jack, DC coupled
Impedance < 2.5 kΩ, unbalanced
Maximum output level +5 V
Trigger operation Active high, +5 V
Controls
Channel trigger button Manually select a stage
Power
Power supply Eurorack
Current draw 40 mA (+12 V),
20 mA (-12 V)
Physical
Dimensions 31 x 40 x 129 mm
(1.2 x 1.6 x 5.1")
Rack units 8 HP
Weight 0.09 kg (0.2 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake,
Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2019 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.
Zhongshan Eurotec Electronics Limited
No. 10 Wanmei Road, South China Modern Chinese Medicine Park,
Nanlang Town, 528451, Zhongshan City, Guangdong Province, China
Loading...