Behringer 961 Quick Start Guide

Quick Start Guide
961 INTERFACE
Legendary Analog Multi-channel Trigger Converter Module for Eurorack
Controls
(1) (2) (4)
(3)
(5)
(7)
(6)
(8)
(1) AUDIO IN – Use this 3.5 mm jack to ro ute an audio
signal into t he module for conver sion to a V-Trig (voltage trigger) signal. The audio signal passes through the SENSITIVI TY control bef ore being convert ed, and the nal, conver ted signal then ex its the module at th e V-TRIG OUT parall el connection s immediately to the r ight of the SENSITIVITY knob.
(2 ) SENSITIVIT Y – Use this knob to adju st the gain of the
audio sign al coming into the modu le through the AUDIO IN jack. Rot ate the knob until yo u nd a setting tha t gives you the best audio-to-voltag e conversion.
(3 ) V-TRIG OUT – Use the par allel jacks to rout e the converted
audio-t o-voltage V-Trig signal bac k out of the module via cables w ith 3.5 mm TS connect ors.
(4 ) S-TRIG IN – Route S-Trig (sw itch trigger) cont rol signals
into the mod ule via cables wit h 3.5 mm TS connector s for conversion to V-Trig (voltage trigger) signals. The conver ted V-Trig signal c omes back out of the module via t he parallel V-TRIG OUT jac ks immediately to the right o f the S-TRIG IN jack.
(5 ) V-TRIG OUT – Use th ese parallel jack s to send the
converte d V-Trig signal bac k out of the module via c ables with 3.5 mm TS co nnectors.
(6 ) V-TRIG IN A/ B – Use these rows of 3.5 mm ja cks to route
in multiple V-Trig (voltage trigger) signals for conversion to an S-Trig (switch t rigger) signal that e xits the module via the S-TRIG O UT jack assigned to th is section of the module. The V-TRIG I N A row of inputs go st raight to conversi on and output, whil e the V-TRIG IN B row of inputs p ass through the SWI TCH-ON TIME contro l before being comb ined with the conver ted A signal for na l output t hrough the S-TRIG OUT jac k. When any valid V-TRIG input ac tivates the S-TRIG ou tput, any other V-TRIG input ac tivity will be i gnored until the r st V-TRIG cycle has ended.
(7 ) SWITCH -ON TIME – Use this knob t o manually limit or
exten d the “ON” time durati on of V-Trig signals c oming in through t he V-TRIG IN B row of in put jacks. The “ON ” time can be var ied from 40 millis econds to a full 4 sec onds.
(8 ) S-TRIG OUT – This jac k routes the nal S-Trig sig nal from
the V-TRIG IN A/B ja cks back out of th e module via cables with 3.5 mm TS co nnectors.
Power Connection
The 961 INTERFACE mo dule comes with the r equired power cab le for conne cting to a standa rd Eurorack power su pply system. Follow the se steps to connec t power to the module. I t is easier to make these c onnections be fore the module ha s been mounted into a rack c ase.
1. Turn the power su pply or rack case p ower o and disconne ct the power cabl e.
2. Insert the 16- pin connector o n the power cable into t he socket on t he power supply or rac k case. The connec tor has a tab that wi ll align with the gap in t he socket, so it can not be inser ted incorrec tly. If the power supply d oes not have a keyed socke t, be sure to orient pi n 1 (-12 V) with the red stripe o n the cable.
3. Insert the 10 -pin connecto r into the socket on th e back of the modul e. The connector ha s a tab that will align wi th the socket for correct orientation.
4. After both en ds of the power cable hav e been securely attac hed, you may mount the mo dule in a case and tur n on the power supply.
Installation
The neces sary screws ar e included with th e module for mount ing in a Eurorac k case. Connect t he power cable bef ore mounting.
Dependi ng on the rack case, th ere may be a series of  xed holes spaced 2 HP ap art along the leng th of the case, or a tr ack that allows indi vidual threaded p lates to slide along th e length of the cas e. The free-movi ng threaded plate s allow precise positio ning of the module, bu t each plate should be p ositioned in the approx imate relation to th e mounting holes in yo ur module before attaching the screws.
Hold the mo dule against the Eur orack rails so that e ach of the mounting h oles are aligned wi th a threaded rail o r threaded plate. Att ach the screws par t way to start, w hich will allow small adjustments to the positioning while you get them all aligned. After th e nal position has b een establishe d, tighten the screws d own.
Specications
Signal Connections
Audio-to-voltage-trigger converter
Audio in 1 x 3.5 mm jack, AC coupled
Input impedance > 3 kΩ unbalanced
V-trig out 2 x 3.5 mm parallel jacks,
Output Impedance < 2 kΩ, unbalanced
Maximum output level +5 V
Switch-to-voltage-trigger converter
S-trig in 1 x 3.5 mm jack, DC coupled
Operation Pull low to trigger
Maximum input level +12 V
V-trig out 2 x 3.5 mm parallel jacks,
Output Impedance < 2 kΩ, unbalanced
Maximum output level +5 V
Voltage-to-switch-trigger converter
V-trig in A 6 x 3.5 mm jacks,
Input Impedance 10 kΩ, unbalanced
Maximum input level +5 V
Minimum level to trigger + 1.5 V
1 x circuit
DC coupled
2 x circuit (left and right)
DC coupled
2 x circuit (left and right)
DC coupled
V-trig in B 6 x 3.5 mm jacks,
AC coupled
Input Impedance 10 kΩ unbalanced
Maximum input level +5 V
Minimum level to trigger + 1.5 V
S-trig out 1 x 3.5 mm jack, DC coupled
Operation Active low
Output level 0 V to +12 V pullup resistor
Controls
Sensitivity 1 x rotary knob
Switch-on time 2 x rotary knob
40 ms to 4 s, adjustable
Power
Power supply Eurorack
Current draw 50 mA (+12 V)
Physical
Dimensions 35 x 106 x 129 mm
(1.4 x 4.2 x 5.1")
Rack units 21 HP
Weight 0.22 kg (0.49 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2019 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.
Zhongshan Eurotec Electronics Limited
No. 10 Wanmei Road, South China Modern Chinese Medicine Park, Nanlang Town, 528451, Zhongshan City, Guangdong Province, China
Loading...