Behringer 960 Quick Start Guide

Quick Start Guide

(2) (3) (4) (5) (6) (7)

(10) (11)

ANOTHER

960 SEQUENTIAL
CONTROLLER

Legendary Analog Step Sequencer Module
for Eurorack

Controls

(1)

(1) OSCILL ATOR - Select the broad oscillator range with the Frequenc y Range

knob, and ne tune with the Frequency Vernier knob. Engage or disengage
the oscillator manually with the OSC ON and OFF buttons, or connect
external voltage trigger (V-trig) signals to control the on/o status.

(2) CONTROL INPUT - Accepts voltage from another module to control the

oscillator frequency.

(8)

(9)

24-Stage Operation

OUT TO

MODULE

The main purpose of the 962 sequential switch module is to alternately selec t
between the 3 output rows of the 960 to create a 24-stage sequence. Patch the
trigger OUT jack from stage 1 into the SHIFT input of the 962. Patch the 3 output
rows A, B, C from the 960 to the 962's 3 SIG inputs. Now the 962's output will be
the 24-stage sequencer output, or leave out the C row patch cable for 16 steps.

Tuning Procedure

1. Power up the 960 module and press the OSC ON button. Allow the unit to
warm up for a few minutes.

2. Prepare the following control settings:

a. Set the 3RD ROW CONTROL OF TIMING switch to o.

b. Set the FREQUENCY rotary switch to 6 on the scale.

c. Make sure no jack is connected to the oscillator CONTROL INPUT.

3. Set the FREQUENCY VERNIER for exactly 100 Hz at the OSCILLATOR OUTPUT
measured with an accurate frequency meter and adjust the DUTY CYCLE ADJ
for 90% duty cycle.

(3) OSCILLATOR OUTPUT - Send the oscillator signal via 3.5 mm TS cable.

(4) IN - Activate any stage via an external voltage trigger (V-trig). Note that if

a stage IN is patched to another stage OUT, it will cause the 960 to reset to
stage 1, bypassing stages after the OUT jack.

(5) OUT - Send the voltage trigger (V-trig) signal to another module.

(6) SET - Manually activate a stage. In the event of a sequencing error, press

any SET button to reset to a stage and restore normal operation.

(7) STAGE MODE - In the Normal setting, the stage runs its cycle and proceeds

to the next stage. Selecting the Skip setting will bypass the stage, and
selecting Stop will stop the sequence. A 9th stage exists to continue
the sequence (Skip) or Stop the sequence at stage 9 which makes the
stage 9 output ac tive. Whenever stage 9 becomes active, the oscillator is
automatically turned o.

(8) VOLTAGE CONTROLS - Adjust the voltage for each stage. The associated

LED will light to indicate the currently-active stage.

(9) OUTPUT SECTION - Send the voltage from the 8 stages to other modules.

The outputs can be scaled with the associated knobs by a factor of 1, 2 or 4.

(10) 3RD ROW TIMING - Since many users will run the 960 as an 8-stage or

16-stage sequencer (via the 962 module), the 3rd row can alternatively
be used to control the timing of each stage. Move the switch to the ON
position and adjust each stage’s 3rd knob to lengthen or shor ten
the duration.

4. Fine-tune the 960 oscillator’s high frequency scaling as follows:

a. Apply exactly +2.0 VDC to the CONTROL INPUT jack (A 921A module
can be used to supply the +2.0 VDC or use a similar low-impedance
stable-voltage source).

b. Trim the 960 SCALE ADJ trimmer to set 400 Hz, then remove the
+2.00 V input and readjust the 960 FREQ VERNIER to 100 Hz.

c. Repeat this cycle until both 100 Hz and 400 Hz are accurate to ±1 Hz
when the +2.00 VDC is plugged in and out of CONTROL INPUT jack.

5. Fine-tune the 960 oscillator’s low frequency scaling as follows:

a. Apply exactly -2.0 VDC to the CONTROL INPUT jack (A 921A module
can be used to supply the -2.00 VDC or use a similar low-impedance
stable-voltage source).

b. Trim the 960 LOW END ADJ trimmer to set 25 Hz, then remove the

-2.00 V input and readjust the 960 FREQ VERNIER to 100 Hz.

c. Repeat this cycle until both 100 Hz and 25 Hz are accurate to ±1 Hz
when the -2.00 VDC is plugged in and out of CONTROL INPUT jack.

(11) SHIFT - Control the shifting via an external source or manually with

the button.

V 1.0

2 960 SEQUENTIAL CONTROLLER Quick Start Guide 3

6. Set the 960 oscillator’s maximum high frequency as follows:

a. Make sure no jack is connected to the CONTROL INPUT.

b. Set the FREQUENCY VERNIER fully clockwise (10 on the scale).

c. Adjust the FREQUENCY ADJUST trimmer to set exactly 500 Hz at the
OSCILLATOR OUTPUT.

d. Apply exactly +2.0 VDC to the CONTROL INPUT jack (this may stop the
oscillator running).

e. Adjust the FREQ STOP ADJ trimmer until the oscillator starts running
and set the maximum frequency to around 550 Hz.

f. Disconnect the +2.0 VDC CONTROL INPUT and check the oscillator
frequency is 500 Hz. Adjust the FREQUENCY ADJUST trimmer if required.

g. Apply exactly +2.0 VDC to the CONTROL INPUT jack, if the oscillator
stays running, the trimming is completed. If not, repeat as required.

Power Connection

The module comes with the required power cable for connecting to a standard
Eurorack power supply system. Follow these steps to connect power to the
module. It is easier to make these connections before the module has been
mounted into a rack case.

1. Turn the power supply or rack case power o and disconnect the power
cable.

2. Insert the 16-pin connector on the power cable into the socket on the
power supply or rack case. The connector has a tab that will align with the
gap in the socket, so it cannot be inserted incorrectly. If the power supply
does not have a keyed socket, be sure to orient pin 1 (-12 V) with the
red stripe on the cable.

3. Insert the 10-pin connector into the socket on the back of the module.
The connector has a tab that will align with the socket for
correct orientation.

4. After both ends of the power cable have been securely attached, you may
mount the module in a case and turn on the power supply.

Installation

The necessary screws are included with the module for mounting in a Eurorack
case. Connect the power cable before mounting.

Depending on the rack case, there may be a series of xed holes spaced 2 HP
apart along the length of the case, or a track that allows individual threaded
plates to slide along the length of the case. The free-moving threaded plates
allow precise positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module before attaching
the screws.

Hold the module against the Eurorack rails so that each of the mounting holes
are aligned with a threaded rail or threaded plate. Attach the screws par t way to
start, which will allow small adjustments to the positioning while you get them
all aligned. After the nal position has been established, tighten the
screws down.

Specications

Inputs

Oscillator on/o

Typ e 2 x 3.5 mm TS jacks, AC coupled

Impedance >3 kΩ, unbalanced

Maximum input level +5 V

Minimum switching threshold +3.5 V trigger

Control input

Typ e 3.5 mm TS jack, 1 V/oct

Impedance 100 kΩ, unbalance d

Maximum input level ±2 V, vernier set to 5

Shift input

Typ e 3.5 mm TS jack, DC coupled

Impedance 7 kΩ, unbalance d

Maximum input level ±5 V

Minimum switching threshold +1. 5 V

Stage triggers

Typ e 8 x 3.5 mm TS jacks, AC coupled

Impedance >3 kΩ, unbalanced

Maximum input level +5 V

Minimum switching threshold +3.5 V trigger

Outputs

Row outputs

Typ e 6 x 3.5 mm TS jacks, DC coupled

Impedance 500 Ω, unbalanced

Maximum out put level +8 V (range X4)

Stage trigger outputs

Typ e 8 x 3.5 mm TS jacks, DC coupled

Impedance 250 Ω, unbalanced

Maximum out put level +5 V, active high

Oscillator output

Typ e 3.5 mm TS jack, DC coupled

Impedance 4 kΩ, unbalance d

Maximum out put level +4 dBu

Duty cycle 90%

Controls

1 (0.04 to 0.5 Hz), 2 (2.75 to 30 Hz)

Frequency range

Frequency vernier Tune the oscillator range, 3 octave range

Oscillator on/o Manually start or stop t he oscillator

Voltage knobs -∞ to max voltage set by the range switch

Mode switch Skip stage, play stage, stop sequencer

Set Manually select stage

Range switches X1 (+2 V), X2 (+4 V), X4 (+8 V) max. output

Timing on/o

Shift button Manually skip to next stage

Power

Power supply Eurorack

Current draw 100 mA (+12 V), 50 mA (-12 V)

Physical

Dimensions 284 x 129 x 47 mm (11.2 x 5.1 x 1.9")

Rack units 56 HP

Weight 0.64 kg (1.41 lbs)

3 (0.17 to 2 Hz), 4 (11 to 130 Hz)
5 (0.7 to 8 Hz), 6 (44 to 500 Hz)

Allows 3rd row knobs to control
stage duration

LEGAL DISCLAIMER

Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and other
information are subject to change without notice. All trademarks are the property
of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy,
Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone and Coolaudio
are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music
Tribe Global Brands Ltd. 2020 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online at
musictribe.com/warranty.