Beckett 61759 User Manual
INSTALLATION INSTRUCTIONS
ELECTRONIC GAS IGNITER
●
240 VAC
APPLICATION INFORMATION:
This igniter is secondary one-end ground and designed for use with 240 VAC Beckett gas burners.
◦
It is rated for continuous duty and can be used with intermittent, or interrupted ignition primary controls.
◦
The Beckett gas igniter is designed to mount in the same manner as standard ignition transformers and igniters.
◦
This igniter can be adapted to multiple base plates to accommodate Beckett residential and commercial burners.
◦
CAUTION! Do not use this igniter beyond its design specifi cations. Improper operation and igniter failure may result.
SPECIFICATIONS:
Input Voltage: 168-264 VAC, 50/60 Hz
Output Voltage: 19 kV peak
Output Current: 25 mA RMS
Input Current: 0.3A
Secondary One-end Ground
Ambient Operating Temperature: -40 to +150° F
Storage Temperature: -40 to +150° F
Moisture: 5 to 95% Relative Humidity, Condensing
Electrical Shock Hazard
Failure to disconnect all power sources
could result in severe personal injury or
death.
Disconnect all electrical power to the burner before servicing.
y
There could be more than one disconnect switch in the supply
circuit.
Installation and service must only be performed by a qualifi ed
y
service technician.
Perform all wiring in compliance with the National Electric Code
y
ANSI/NFPA 70 (Canada CSA C22.1).
Connect burner housing and circuit to earth ground.
y
Installation Instructions (If base plate is already
installed, skip to step number 8):
Locate the igniter blue “hot” and the white “neutral” input leads.
1.
Install the 32411 igniter gasket, if required, and route the leads
2.
through the appropriate base plate lead exit hole. Make sure
these leads are not being crushed.
Mount the igniter fl ush to base plate with the mounting screws
3.
supplied.
Table 1 - Complete Igniter Base Plate Assemblies
Part No. Burner Models
5199704U CG10 & CG10A
5199705U CG15, CG25, & CG50
Note: Use #6 x 7/16” screws when using the bottom mounting
4.
holes. Use #10 thread forming paint scraping screws, if using
the two top mounting holes for 5199704. For 5199705, use
1/4” machine screws, placing (1) 1/4” lockwasher between
screwhead and baseplate to ensure ground for 5199705.
Tighten all screws securely.
5.
Install base plate gaskets for Beckett CG10, CG15, CG25 and
6.
CG50 burners.
Use of top mounting screws is possible for Beckett CG10
7.
through CG50 burners.
Mount the assembled unit to the burner using the screws
8.
supplied.
Use “paint scraping” screws for all burners (2 at the hinge and
9.
at least 2 for non-hinged base plates). Tighten these screws
securely to provide effective grounding to burner housing.
Verify the burner is properly grounded.
10.
Carefully route the igniter input leads to prevent them from
11.
being pinched during closing.
Wire white to neutral and blue to primary control ignition
12.
lead. Refer to the burner or appliance manufacturer’s wiring
diagram.
Verify the igniter secondary output terminal lead is correctly
13.
arranged to make good electrical contact with the gas burner
electrode.
Verify the ignition electrode gap and orientation are set to the
14.
manufacturer’s specifi cations.
Close the igniter. Install and securely tighten the two front
15.
base plate retaining screws (4 screws if no hinge).
Reconnect electric power to the burner circuit.
16.
Verify with instruments that the burner is adjusted to the
17.
manufacturer’s recommended settings
Cycle the burner several times to verify prompt and smooth
18.
ignition before leaving.
Electrical Shock Hazard
e
3
t
Failure to wire the burner correctly could cause
serious injury or death.
Perform all wiring in compliance with ANSI/NFPA 70 (Canada CSA 22.1).
y
Connect the electrical circuit and burner housing to earth ground.
y
Figure 1 - Igniter Assemly Components - 5199704U shown.
Igniter
Igniter
Igniter Input Leads
niter Input Leads
240 VAC Gas Igniter
32411 Igniter Gasket
2411 Igniter Gaske
(between baseplate and igniter)
Mounting Screws
ounting Screws
Baseplate
aseplat
Baseplate Gasket
Table 2 - Igniter Base Plate Bill of Materials
Part No. Burner Models Baseplate Gasket Baseplate Igniter Gasket
5199704U CG10 & CG10A 31481 51855BK 32411
5199705U CG15, CG25, CG50 31412 32173BK 32411
R.W. BECKETT CORPORATION
P.O. Box 1289, Elyria, Ohio 44036
R.W. BECKETT CANADA, LTD
430 Laird, Unit 3, Guelph, Ontario, N1G 3X7
Part No. 61759 R02, Printed in the USA 05/10
Loading...