Becker TRAFFIC PRO 7945 User Manual

Download

Operation Guide

Manual de usuario

Manual de instruções

Contents

Safety instructions 7 Information regarding general

road safety 8 Overview of controls Traffic Pro 9

Overview of controls Traffic Pro with Bluetooth® 10

General operation 11

Menu basics 11

Fast access function 11 Main menu 11 Status display 12 Options menu 12 How to use the menus 12 Data entry menus 13

Anti-theft device 14

Entering unit code numbers 14

What to do if an incorrect code number has been entered 14

Removing/Inserting the control panel 15

Removal 15 Insertion 16

Inserting/Removing the cover 16

Inserting the cover 16 Removing the cover 16

Switching the unit on/off 17

Switching on 17 Switching off 17

Setting the volume 18

Sound settings 18

Calling up the sound settings 18 Setting the equalizer 19

Defining the equalizer setting 19

Setting balance and fader 20

Balance setting 20 Fader setting 20

Switching loudness on/off 20 Becker Surround 21 Subwoofer 21 Crossover 21 Reset settings 22

Mute 22

Navigation mode 24

What is navigation? 24 Navigation CDs 24 Selecting navigation 26 Calling up the Navigation main menu 26 Entering a destination 27

Selecting a country 28 Entering a destination town 28 Selecting destination via postcode 29 Entering the destination road 30 Entering the destination town centre 31 Entering house number for destination road 32 Selecting junction for destination road 32 Setting the route options 33

Saving/Deleting route options 34

Saving a destination 34

Navigation fast access 35

Navigating from fast access 35 Protecting an entry 35 Deleting an entry 36 Deleting a list 36 Saving an entry in the address book 36

Creating a new entry 37 Adding data to entries 37

Selecting a destination from the address book 38 Point of interest 39

Local 40 In country 40 Local area of destination 41 In place 41 Information about points of interest 42

During route guidance 43

Navigation status screen 43 Example navigation displays 44 Options menu 45

Cancelling route guidance 46 Traffic announcements 47 Route list 47 Stopover 47 Blocking a route 49 Modifying route options 49 Switching navigation announcements on/off 50

*Only available for the Traffic Pro with Bluetooth® wireless technology.

Contents

Information during route guidance 50

Displaying destination information 50 Displaying/Storing position 51 Displaying traffic announcements 51

Displaying/Changing route settings 52 Information during non-active route guidance 52

Displaying/Storing a position 52

Displaying TMC messages 52

Dynamic route guidance with TMC 52

What is dynamic route guidance? 52

Dynamic route guidance 53

Displaying traffic information 54

Settings 55

Traffic announcements 55

Announcing the time of arrival 56

ETA setting 56

Measuring unit 57

Radio mode 58

Switching on radio mode 58

Calling up the Radio main menu 58 Selecting a waveband 59

FM mode 60

Possible settings for FM stations 60

Station list 60 Scan function 61 Manual station tuning 62

Filter function 62

Switching the filter function on/off 62 Filtering stations 63 Filtering stations 63 Cancel filtering 63

Programme type 64

Switching the programme type function on/off 64 Selecting the programme type 64

Regionalisation 65 Radio text 65 Voice entries 66 Reception optimisation 66 Bandwidth control 67

Traffic programme 67

Switching a traffic programme on/off 68 Selecting a TP station 68

Automatic 68 Manual TP station selection 68

TP volume 69 Cancelling traffic announcements 69

AM mode 69

Possible settings for AM stations 69

Scan search 70 Scan function 70

Station memory 71

Calling up the station memory 71 Storing stations 71

Different waveband set 71 Station already in memory 72

Moving stations 72 Deleting stations 73 Naming stations 73 Creating/Deleting voice entries 74

Create 74 Deleting 74

Reading out voice entries 74

Media mode 75

Activating media mode 75

Media fast access functions 75 Media status display 76

Track jump/Track skip 77 Fast forward/rewind 77

Play mode 78

Calling up the Play Mode menu 78 Track mix (random play function) 78 Scan 79 Repeat track 79 CD mix 79 Repeat CD 80 Directory mix 80

Calling up the Media main menu 80

Switching detailed track display on/off 81

CD mode 81

Notes on compact discs (CD) 81 Inserting/Ejecting CDs 82 Notes on CD-R and CD-RWs 82 Notes on copy-protected CDs 82 Temperature protection circuit 82

*Only available for the Traffic Pro with Bluetooth® wireless technology.

Contents

MP3 mode 83

General notes on MP3 83 Creating an MP3 storage medium 83 MP3 CD mode 84 MP3 memory cards/ Micro-drive mode 84

Inserting a micro-drive/ memory card 85 Removing a micro-drive/ memory card 85

CD changer mode 86

Operational readiness of CD changer 86 Loading/Ejecting the CD magazine 86

External units/AUX mode 86

Telephone mode 87

Calling up the telephone 88

Bluetooth not yet switched on 88 Bluetooth mobile phone not yet connected 88

Calling up the Telephone main menu 89

Dialling numbers 90 Selecting a number from the address book 91 Call lists 92

Calling a number from the list 93 Retrieving information about the entry 93 Deleting a call list 93

Emergency call 93 Settings 94

Automatic call answering 94 Dialogue with call 94

Telephone calls 95

Status display 95 Accepting/ rejecting a call 95

Accepting a call 95 Rejecting a call 96

Ending a call 96 Options menu 96

End call 97 DTMF 97 Private 97

Fast access telephone functions 98

Direct calling 98 Protecting an entry 99 Deleting an entry 99 Deleting a list 99 Saving a number in the address book 100

Creating a new entry 100 Adding data to entries 101

Address book 102

Calling up the address book 102

Calling up the Address Book main menu 102 Creating an entry 102 Creating an entry which supports navigation 104

Find entry 105

Setting the search criterion 106

Editing entries 107

Modifying an entry 107 Deleting an entry 108 Creating/Deleting voice entries 108

Create 108 Delete 109

Reading out voice entries 109

Exporting an address book* 109 Exporting an address book entry* 110 Importing an address book entry* 110 Navigating to an address book entry 112 Voice entries 112 Calling an address book entry* 113 Fast access functions 113

Protecting an entry 113 Deleting an entry 114 Deleting a list 114

Settings 115

Calling up general settings 115 Bluetooth* 115

Opening the device list* 115

Always allow connection* 116 Name device* 117 Deleting a device from the list* 117

*Only available for the Traffic Pro with Bluetooth® wireless technology.

Contents

Connecting and disconnecting

devices* 117

Connecting devices (Traffic Pro BT)* 118 Connecting a device (external device)* 119 Disconnecting devices* 121

Calling up Bluetooth settings* 121

Activating/ deactivating Bluetooth* 122 Searching for Bluetooth devices* 122 Making devices visible to others* 123 Device name* 123

Voice mode 123

Calling up voice mode settings 123

Setting the system language 124 Displaying voice settings 125 Volume for voice output 125 Automatic dialogue 126 Voice entries 126 Voice output 126 Extended PTT 127 Repeating a voice announcement 127

System settings 128

Calling up the system settings 129

Audio 129

GAL (speed dependent volume) 129 Settings for left-hand/ right-hand drive vehicles 129 Volume for acoustic signals 130 Displaying the volume 130 Digital level 130

External device 131 Display brightness 131 Day/ night design 131 Reset function 132 Direction of rotation of the rotary control/push button 132 Clock 133

Software update 133

Voice mode 135

What is voice mode? 135

Symbols 135

General information about the voice control system 136

Activating the voice control system 136

Ending voice dialogue prematurely 137

Voice entries 137 Settings 138

Examples for a voice dialogue 138

Example operation in radio mode 139 Example for entering a navigation destination 140 Example for entering a telephone number* 142

General commands 142

Help function (online help) 143 Aborting voice dialogue 143 Navigation in lists 143 Calling up the status display 143

Commands for status displays, fast access functions and main menus 144

Commands for radio mode 145

Commands for the radio status display 145 Commands for radio fast access mode 147

Commands in the Edit Station menu 148

Commands for the Radio main menu 149

Commands in the Waveband menu 150 Commands in the Programme Type menu 151 Commands in the Filter menu 151 Commands in the TP menu 152 Commands in the Voice Entries menu 152 Commands in the Reception Optimisation menu 153

Commands for media mode 153

Commands for the media status display 154 Commands for media fast access 155 Commands for the Media main menu 156 Commands for the media Play Mode menu 156

*Only available for the Traffic Pro with Bluetooth® wireless technology.

Contents

Navigation commands 157

Correction option for incorrect destination entry 157

Commands for the navigation status display 158 Commands for navigation fast access 159

Commands in the Fast Access/ Edit Destinations menu 160

Commands for the Navigation main menu 160 Commands for the Destination menu 161 Commands for the POI menu 162

POI categories (page 39) 163

Commands for the Route Options menu 163 Commands for the Stopover menu 164

Prompt: Is the new destination a main destination or a stopover? 165

Commands for telephone mode* 165

Commands for telephone fast access mode* 165

Commands in the Fast Access/ Edit Telephone Numbers menu* 167

Commands for the Telephone main menu* 167

Commands in the input menu for telephone numbers* 168 Commands in the Call Lists menu* 168 Commands in the call lists* 169 Commands in the Settings menu* 170

Commands for the address book 170

Commands for address book fast access 170

Commands in the Fast Access/Edit Entries menu 173 Commands in the Edit menu 173 Commands in the Edit Data menu 174 Commands in the menu for selecting a Bluetooth device for export* 174 Commands when an entry is open 174

Commands for the Address Book main menu 174

Commands in the Voice Entries menu 175 Commands in the Search Criterion menu 176

Technical terminology 177

Technical data 188

NOTICE 189

*Only available for the Traffic Pro with Bluetooth® wireless technology.

Safety instructions

Operation of the unit is permitted only if traffic conditions are suitable and you are absolutely sure that you, your passengers or other motorists are not endangered, obstructed or inconvenienced.

In all cases, all applicable road traffic regulations must be obeyed. Destinations may only be entered when the vehicle is stationary.

The country-specific regulations apply for telephone operations.

The navigation system is only an aid. Errors may occur in individual data items/entries. At all times, the driver must decide whether or not to heed the information provided. We do not accept liability for erroneous data provided by the navigation system.

Due to continual changes in traffic routing or deviations in the data, it may occur that imprecise or erroneous information is given. Therefore, actual road signs and traffic regulations must always be observed. In particular, the navigation system cannot be used as an orientation aid at times of poor visibility.

The unit may only be used for its intended purpose. The volume of the radio, navigation system and telephone should be adjusted so that external noise is still audible.

Do not activate the telephone near petrol stations, fuel depots, chemical plants or blasting areas.

In the case of a malfunction (i.e. smoke or other noticeable odours) the unit is to be turned off immediately.

For safety reasons, the unit must only be opened by a trained technician. Please refer to your dealer for repair.

Information regarding general road safety

This car radio device is intended and approved for installation and operation in passenger cars, commercial vehicles and buses (vehicle classes M, N and O) whose electric system has a rated voltage of 12V.

Installation and maintenance should only be carried out by specialists. Faulty installation or maintenance can result in the malfunctioning of the motor vehicle’s electronic systems. The vehicle manufacturer’s safety instructions must be observed.

The vehicle’s electronics (e.g. speedometer signal) must only be worked on by an authorised service garage. We assume no liability for any impairment of the vehicle’s electronics.

This device is only intended for installation in the area provided for this purpose by the vehicle manufacturer.

The method of attachment used must ensure that the device will remain properly attached, should the vehicle be involved in a crash.

The power supply must be properly fused.

Using mobile phones without an external antenna in the proximity of the radio unit may cause interference.

Familiarise yourself with the device and how it works before embarking on your journey. Whilst on the move, only operate the device in appropriate traffic conditions. The volume of the device should be set at a level that enables external noises (e.g. police sirens) to be easily heard.

Overview of controls Traffic Pro

1 Information button ( )

2 On / off switch ( )

3 Select radio ( )

4 Select CD/CDC/memory card ( )

5 Select navigation ( )

6 Select sound settings ( )

7 Select address book ( )

8 CD eject button ( )

9 Status button ( )

6 7

8 9

10 Right-hand rotary control/push button ( )

Press = Confirm Turn = Scroll through lists and menus

11 Back button ( ) 12 Button for unlocking removable control panel 13 Display

14 Arrow keys ( and )

Change radio station and audio track

15 Left-hand rotary control/push button ( )

Press = Activate voice dialogue Turn = Set volume

Overview of controls Traffic Pro with Bluetooth®

1 Information button

2 On / off switch

3 Select radio

4 Select CD/CDC/memory card

5 Select navigation

6 Select telephone

7 Select address book

8 CD eject button

9 Status button

6 7

8 9

10 Right-hand rotary control/push button

Press = Confirm Turn = Scroll through lists and menus

11 Back button 12 Release slide for removable control panel 13 Display

14 Arrow keys and

Change radio station and audio track

15 Left-hand rotary control/push button

Press = Activate voice dialogue Turn = Set volume

General operation

Menu basics

Note

If an entry in the list is abbreviated because it is too long (three dots appear at the end of the text), you can display the entry in full briefly by pressing and holding down the button.

Fast access function

The fast access function provides fast access to the major functions in the various operating modes. In most cases, you may then make selections from lists (radio stations, navigation destinations, etc.). Select the first entry in the list to go to the Operating Mode main menu.

Note

If no selections are made for a short period of time when the fast access function is displayed, the display will automatically switch to the status display for the active operating mode.

1001

The fast access function for the radio is shown here by way of example. Press the various operating elements to access:

• The radio fast access function

• The media fast access function (CD, CD changer and memory card)

• The navigation fast access function

• * the telephone fast access function (if Bluetooth is activated and a telephone is connected).

• The address book fast access function

General operation

Main menu

The main menu for each operating mode provides access to the various functions and possible settings for that mode.

1002

The Radio main menu is shown here by way of example. The main menu for the various operating modes can be called up in two different ways:

• Activate the fast access function (press , , , * or ).

X Turn the rotary control/push button

to select the first entry in the fast access list.

X Press the rotary control/push button

X Press the button for which you have

called up the fast access function again ( , , , * or

*Only available for the Traffic Pro with Bluetooth® wireless technology.

General operation

1003

1004

Status display

All the information you need about the current operating mode appears on the status screen.

Note

The address book does not have a status display.

If navigation is also active in addition to the current radio or media operating mode, a combined display may appear.

The radio status display is shown here by way of example.

The radio status display with active navigation route guidance is shown here.

The status display can always be accessed by pressing . If route guidance is active, you can toggle between the combined display and the status display by pressing repeatedly.

Options menu

You can call up the Options menu in the status display.

X Press the rotary control/push button

The Options menu appears.

You can access the major functions for the active operating mode directly in the Options menu. Some of the possible settings and functions in the Options menu can also be set/activated via the main menu.

1005

The Options menu for the radio function is shown here by way of example.

How to use the menus

The commands are the same for all menus.

1005

The Options menu for the radio function is shown here by way of example. Turn the rotary control/push button to scroll through the menus.

Once you have made an entry in a menu, the next menu will appear or you can select the entry (by turning the rotary control/push button ) to activate/ deactivate a function.

General operation

If the menu entry is concealing another menu, a small triangle will appear after the menu entry.

or in front of a menu entry indicates that a function can be activated or deactivated. The symbol stands for off and the symbol for on.

Note

You can always press to go back one step in the menu hierarchy.

Data entry menus

If data can be entered, special data entry menus appear.

6003

The data entry menu for the surname in an address book entry appears in the example.

X Turn the rotary control/push button

and then press the rotary control/push button to select each letter one after the other.

Note

Select the symbol to delete the last character in the entry. If, when selecting the symbol , the rotary control/push button is pressed for longer than 2 seconds, the complete entry is deleted.

You can change the character set for the available characters by selecting various symbols.

• Switch to lowercase

• Switch to uppercase

• Switch to numbers

• Switch to special characters

• Switch to lowercase international

• Switch to uppercase international

Accept entry:

X In the data entry menu, select the

symbol.

X Press the rotary control/push button

and hold it down for at least 2 seconds.

General operation

Anti-theft device

Your Traffic Pro features two anti-theft devices:

• Protection by means of a five-digit

unit code number

• Protection by means of a removable

control panel

Entering unit code numbers

If the Traffic Pro is disconnected from the electrical supply source, the antitheft device prevents it against unauthorised use once it has been reconnected. You need the five-digit code number printed on the CODE CARD to start up the Traffic Pro.

Note

It is important to store the CODE CARD in a safe place outside of the vehicle. This will prevent unauthorised use. The window stickers provided can be attached to the windscreen/windows inside your vehicle.

Shortly after the unit has been switched on by pressing , the data entry menu for the code number will appear.

1006

X Turn the rotary control/push button

to select the first digit of the code number.

X Press the rotary control/push button

X Enter the remaining digits of the code

number in the same way.

Note

If you enter an incorrect number:

X Press the back button to delete

the last number entered.

X Select the symbol.

Once you have entered all 5 digits of the code number correctly, the Traffic Pro will come on automatically and you can use all functions.

What to do if an incorrect code number has been entered

The following message appears if an incorrect code number is entered.

1007

X Press the rotary control/push button

. The data entry menu for the code number appears again.

X Enter the correct code number as

described above.

General operation

1008

Note

Entering an incorrect code number three times will disable the unit for approx. 1hour.

The time remaining until another attempt can be made to enter the code number is displayed.

X Leave the ignition switched on.

Switching the ignition off resets the waiting time of one hour to zero. Once the waiting time has elapsed, the data entry menu for the code number appears again.

Removing/Inserting the control panel

Part of the control panel can be removed to provide additional effective protection against theft. The Traffic Pro cannot be switched on without this removable control panel.

Removal

X Push the release slide for the control

panel (A) to the right.

The control panel is released.

X Remove the control panel from the

mount. If the Traffic Pro is still switched on when the control panel is removed, it is switched to mute and disabled.

1009

If the control panel is reinserted within 45 seconds, the Traffic Pro will automatically switch itself back on.

Notes

• Please insert the control panel into the accompanying protective cover after removal. Do not touch the metal contacts on the control panel or on the Traffic Pro.

• If you move your vehicle once the control panel has been removed, once you insert the control panel, it will take some time for the navigation system to ascertain your position.

General operation

Insertion

X Take the control panel out of its pro-

tective cover.

X Insert the left-hand side of the control

panel.

X Push the control panel into place.

The Traffic Pro is now ready for operation and can be switched on, or it will switch itself on automatically.

Note

If a new control panel or the control panel for a different Traffic Pro is inserted, the code number for the Traffic Pro must be entered as described in “Entering unit code numbers” on page 14.

Inserting/Removing the cover

The scope of supply of the Traffic Pro includes a red plastic insert. This plastic insert can be snapped into the gap which appears once the control panel has been removed. As well as serving as a protective cover for any CF card/micro-drive, the red colour of the plastic insert clearly indicates that the control panel has been removed.

Inserting the cover

X Remove the control panel as described

in “Removing/Inserting the control panel” on page 15.

X Insert the plastic insert into the gap

with the hole at the top and the smooth side facing outwards.

X Push the lower section of the plastic

insert into the gap until it snaps into place.

The cover has now been inserted.

X Reinsert the control panel as described

in “Removing/Inserting the control panel” on page 15.

Removing the cover

X Remove the control panel as described

in “Removing/Inserting the control panel” on page 15.

X Insert your finger into the hole in the

plastic insert.

X Carefully push the plastic insert down-

wards.

X Pull the plastic insert forwards.

The cover has now been removed.

X Reinsert the control panel as described

in “Removing/Inserting the control panel” on page 15.

General operation

1010

Switching the unit on/off

Switching on

X Press .

X If the Traffic Pro was switched off via

the ignition, the Traffic Pro will switch back on once the ignition has been switched on.

X Confirm the warning which appears

by pressing the rotary control/push button .

Notes

• Unless the warning message is confirmed, the Traffic Pro will remain disabled.

• Once it has been switched on, the Traffic Pro will play back the last source selected (radio or media). Any mute or pause function activated will be cancelled.

• If fewer than approx. 2 hours have elapsed since the unit was last switched off, active route guidance will be restarted.

• If the volume was set to a very loud value before the unit was last switched off, it will be reset to setting 26 when the unit is switched back on.

Switching off

X Press .

If the ignition is switched on, the Traffic Pro is switched to standby mode. The display goes dark and the Traffic Pro sound is switched off.

X Switch off the vehicle ignition.

1010

The shutdown display appears for approx. 5 seconds. During this period of approx. 5 seconds, shutdown can be aborted by pressing one of the buttons on the Traffic Pro or by switching the ignition back on. The Traffic Pro then switches itself back on and plays back the last source selected (radio or media).

General operation

1011

Setting the volume

There are 50 volume settings. The volume setting applies to all radio and audio sources. You can specify whether changes in volume should be displayed in graphics format or not in “Displaying the volume” on page 130.

X Turn the rotary control/push button

clockwise/counter clockwise.

X The volume increases or decreases.

Note:

Subsequent sections of the operation guide describe how to set the volume for:

• Traffic announcements (page Page 69)

• Navigation announcements and other voice messages (Page 125)

• Acoustic signals (Page 130)

Sound settings

You can configure the sound of your Traffic Pro to meet your requirements in the sound settings. The settings are also valid for all radio/audio sources.

Calling up the sound settings

X Press .*

X Press or until the sound

settings appear.

X Select 6RXQG in the radio or Audio

main menu (Radio main menu Page 58/Audio main menu Page 80).

1012

XTurn the rotary control/push button

to select one of the following options:

(TXDOLVHU, %DODQFHIDGHU, /RXGQHVV, %HFNHUVXUURXQG, &URVVRYHU, 6XEZRRIHU and 5HVHWVHWWLQJV

X Confirm your selection by pressing

the rotary control/push button .

Note:

Press one of the buttons , ,

, or in order to quit

the sound settings.

*Only available for the Traffic Pro with Bluetooth® wireless technology.

General operation

1013

Setting the equalizer

You can switch the acoustic pattern on 5 frequency bands with the equalizer setting. 4 equalizer presets are also available for selection. An additional option also allows you to make another 3 equalizer settings.

X Select (TXDOLVHU in the sound settings.

X Next, turn the rotary control/push

button to select one of the four equalizer presets ( and &ODVVLFDO) or one of the three userdefined equalizer settings (



or /LQHDU).

5RFN3RS, -D]]0XVLF

8VHU - 8VHU

X Turn the rotary control/push button

to apply the required equalizer setting.

Note:

The equalizer presets (

0XVLF

and &ODVVLFDO) cannot be modified.

Select

/LQHDU to set the equalizer settings

5RFN 3RS, -D]]

to an average value.

Defining the equalizer setting

X Select 8VHU, 8VHU or 8VHU. X Press and hold down the rotary control/

push button .

1014

The cursor jumps to the first frequency band.

X Turn the rotary control/push button

to select the frequency band to be changed.

X Confirm your selection by pressing

the rotary control/push button .

1015

X Turn the rotary control/push button

to select the required setting for the selected frequency band.

X Confirm the setting by pressing the

rotary control/push button .

You may now change other settings. Once you have made the required settings:

X Press and hold down the rotary control/

push button .

X Turn the rotary control/push button

to select the arrow next to the frequency bands and press the rotary

control/push button . You may now make other equalizer settings or select one of the presets.

General operation

1016

Setting balance and fader

You can shift the tone centre in the vehicle using the balance and fader setting.

X Select %DODQFH  IDGHU in the sound

settings.

An image of the vehicle interior in the direction of travel appears on the display. The small triangle indicates the current position of the tone centre. The Balance setting is active.

X Turn the rotary control/push button

to select

%DODQFH or )DGHU.

Balance setting

X Turn the rotary control/push button

clockwise/counter clockwise.

1016

The tone centre moves to the right/left.

Fader setting

X Turn the rotary control/push button

clockwise/counter clockwise.

1017

The tone centre moves forwards/backwards.

Switching loudness on/off

With loudness, the sound is improved by increasing the bass volumes (especially suitable for low-volume settings).

X Select /RXGQHVV in the sound settings.

1018

X Press the rotary control/push button

to switch loudness on ( ) or off ( ).

General operation

1019

Becker Surround

You can use this function to activate virtual surround sound and select the vehicle size to optimise the surround sound function.

Note:

The Becker Surround function is not available for medium wave or short wave.

X Select %HFNHU VXUURXQG in the sound

settings.

X Select %HFNHU VXUURXQG and press the

rotary control/push button to switch virtual surround sound on ( ) or off ( ).

X Select /DUJHYHKLFOH or 0HGLXPVL]HGYHKL

FOH

(on = ).

Note:

Only one of the vehicle types in the list can be active ( ).

Subwoofer

You can set the volume level of the subwoofer output/ deactivate the subwoofer output.

X Select 6XEZRRIHU in the sound settings.

Crossover

Use this function to set the threshold frequencies for the front loudspeakers, the rear loudspeakers and the subwoofer.

X Select &URVVRYHU in the sound settings.

1024 1025

X Turn the rotary control/push button

to select the required value.

Note:

A setting of "+10" indicates an increase in the volume of the subwoofer. Select

RII to deactivate the subwoofer

output. In addition,

6XEZRRIHU is deactivated

with the crossover setting.

X You may now select )URQWORXGVSHDNHUV,

5HDUORXGVSHDNHUV or 6XEZRRIHU.

•

)URQWORXGVSHDNHUV and 5HDUORXGVSHDNHUV

You can set the lower threshold

frequency of the front and rear

loudspeakers to a value of between 20

and 150 Hz.

•

6XEZRRIHU

You can set the upper threshold

frequency of the subwoofer to a value

of between 50 and 150 Hz.

General operation

1026

In this example you can see the settings for the front loudspeakers.

X Turn the rotary control/push button

to select the required value.

Reset settings

You can reset all sound settings to the default settings. The following settings are reset to the relevant default value:

•

(TXDOLVHU: All default settings are reset

to the initial value. The user-defined setting is reset to zero.

•

%DODQFHIDGHU to centre setting

•

/RXGQHVV to off

• %HFNHUVXUURXQG to off

•

6XEZRRIHU to 0.

•

&URVVRYHU front and rear loudspeakers

to 50 Hz, subwoofer to 100 Hz.

X Select 5HVHW VHWWLQJV in the sound set-

tings.

1020

X Select <HV to reset the sound settings

1R to continue without making any

changes.

Select

<HV to reset the sound settings.

Mute

You can switch your Traffic Pro to mute, i.e. switch off the sound from the current radio/media source. However, navigation announcements, traffic announcements (if TP has been activated) and other voice announcements on the Traffic Pro continue to be transmitted unaffected.

X Press the rotary control/push button

and hold it down for at least

2 seconds.

1021

Example of muted radio mode.

1022

Example of muted media mode.

You can deactivate the mute function as follows:

• Press the rotary control/push button again and hold it down for at least 2 seconds.

• Change the volume by turning the rotary control/push button .

•Press or .

• Select another station or track.

• Switch the Traffic Pro off and back on again.

General operation

Navigation mode

What is navigation?

The term “navigation” (lat. navigare = to travel by sea) is generally understood to mean the location of a vehicle, the determination of the direction and distance from the desired destination and the required route. As navigation aids, stars, prominent landmarks, compass and satellites are used. With Traffic Pro, location is determined with the GPS receiver (GPS = Global Positioning System). The direction and distance from the destination are determined using a digital road map, a navigation computer and sensors. A speedometer signal and a reverse signal are additionally used to calculate the route. For safety reasons, navigation is pre- dominantly in spoken form supported by a direction indicator on the display.

Safety instructions

• Road traffic regulations always take priority. The navigation system is only an aid. Errors may occur in individual data items/entries. At all times, the driver must decide whether or not to heed the information provided. We do not accept liability for erroneous data provided by the navigation system.

• Observation of traffic signs and local traffic regulations must always take priority.

• Traffic guidance is restricted to passenger vehicles only. Special driving recommendations and regulations for other vehicles (e.g. commercial vehicles) are not included.

• Destinations may only be entered when the vehicle is stationary.

Navigation CDs

Two navigation CDs are supplied with the navigation unit. These CDs contain a digitised road map. One CD for Northern/Eastern Europe (CD no. 1) and one CD for Southern/ Western Europe (CD no. 2) are supplied. The complete trunk road network in the digitised area of Northern and Southern Europe are available on the CDs. All digitised roads of the northern/eastern countries are also included on the Northern/Eastern Europe CD. All digitised roads of the southern/western countries are also included on the Southern/Western Europe CD. In these detailed areas of the Northern/ Eastern or Southern/Western Europe CD road map, motorways, regional roads and unclassified roads as well as country roads are stored. Larger cities and communities are comprehensively covered. For smaller towns and communities, the regional and unclassified roads or access roads and the town centres are included.

Navigation mode

One-way streets, pedestrian zones, turn bans and other traffic regulations are taken into account as far as possible. There may be discrepancies between the data on the navigation CD and the actual local situation, due to permanent changes to road systems and their traffic regulations.

Note:

For Norway, Sweden, Finland and Denmark, non-verified data has been used to achieve a high depth of digitisation; i.e. with this data, the navigation system cannot refer to information such as motorway, trunk road, 30 zone, oneway street or other traffic regulations, as this is not recorded. All roads can be used, but optimum route guidance cannot be guaranteed.

Navigation with two European CDs For example, if you wish to navigate

from a town on the Southern/Western

Europe CD (D) to a town on the Northern/Eastern Europe CD (B), enter your destination address. After entering the town, you will be prompted to insert navigation CD 1 by the display

 IRU GHWDLOHG QDYLJDWLRQ GDWD /DQG

,QVHUW&'

After inserting the relevant CD, enter the town, the road and, if required, the house

number or the town centre. The required map data is loaded and

stored internally after route calculation has started.

A Area of Northern/Eastern Europe CD

with all digitised roads.

B For example, a town or an address in

Germany (on the Northern/Eastern Europe CD).

C Area of Southern/Western Europe CD

with all digitised roads.

D For example, a town or an address in

France (on the Southern/Western Europe CD).

Navigation mode

2001

2002

Selecting navigation

X Press .

Navigation is activated. The display only appears if navigation has not been activated since the last time the Traffic Pro was switched on or if it is not yet ready.

The Fast Access menu then appears. The number of satellites received appears on the right-hand side of the display (in the example, 5 of the maximum of 8 receivable satellites are being received). In fast access mode, you can select and navigate to the last destinations entered/ the destinations you have stored in fast access mode. For more information, see “Navigation fast access” on page 35.

Note:

The navigation CD must be loaded when starting navigation mode for the first time. If calibration of the navigation system has not yet been completed, the system will prompt you to take a drive for calibration (see Installation Guide). A navigation CD containing the data for the target country is required for navigation operations. The navigation CD must be inserted to start the calculation of a route. During calculation, the symbol appears on the right-hand side of the display. Once the calculation has been completed, the

symbol disappears, the navigation CD can be removed and an audio CD may be inserted. When entering destinations, driving off should be delayed until the symbol has disappeared. For distant destinations, you may be prompted to re-insert the navigation CD at a later time.

Calling up the Navigation main menu

X Press twice.

X Press .

The Fast Access menu appears.

X Select the 1DYLJDWLRQPHQX entry.

Old version

The Navigation menu appears.

X Turn the rotary control/push button

to select one of the following options:

(QWHUDGGUHVV, 'HVWIURPDGGERRN, 6SHFLDO'HVW or 6HWWLQJ

X Confirm your selection by pressing

the rotary control/push button .

The required function is called up.

Navigation mode

• (QWHUDGGUHVV Accesses the data entry menu for the destination. See “Entering a destination” on page 27.

•

'HVWIURPDGGERRN

You can select a destination from the address book. See “Selecting a destination from the address book” on page 38.

•

6SHFLDO'HVW

Access the POI selection menu. POIs include petrol stations, airports or hospitals, for example. See “Point of interest” on page 39.

•

6HWWLQJ

Accesses the Navigation Settings menu. See “Settings” on page 55.

Note

If route guidance is already active, you can start to enter another destination by selecting

ERRN

(QWHU DGGUHVV, 'HVW IURP DGG

and 6SHFLDO'HVW. Once the destination has been selected, the Traffic Pro will prompt you to confirm if the new destination is to be used as the main destination or a stopover.

2096

X Turn the rotary control/push button

to select

X Confirm your selection by pressing

the rotary control/push button . Depending on the selection, the new destination is now used as a stopover or the new main destination.

6WRSRYHU or 0DLQGHVW.

Entering a destination

X In the Navigation main menu, select

the

(QWHUDGGUHVV entry.

2004

The Enter Destination menu appears. The last country selected and the last town selected appear first.

X Turn the rotary control/push button

to select one of the following options:

*5($7%5,7$,1(country as example), */$6*2:(town as example), 6WUHHW, 6WDUWURXWHJXLGDQFH, +RXVHQXPEHU, ,QWHUVHFWLRQ, &HQWUH, 3RVWDOFRGH (postcode), 5RXWHVKRUW/5RXWH IDVW or 5RXWH G\QDPLF

and

6DYHGHVWLQDWLRQ

X Confirm your selection by pressing

the rotary control/push button .

Navigation mode

The corresponding menu appears or the required action is initiated.

Note

Some entries in the Enter Destination menu cannot be selected directly. For example, a house number cannot be entered unless the name of a road has been entered first. These non-selectable entries are greyed out in the display and cannot be selected. The entry will also be greyed out if no house numbers are available for a specific road.

Selecting a country

If your destination is located in a different country (

*5($7 %5,7$,1 in the example

display) you must first select the required country.

X In the Enter Destination menu, select

the country (

*5($7%5,7$,1 in the exam-

ple).

2005

X Turn the rotary control/push button

to select your destination country.

X Confirm your selection by pressing

the rotary control/push button .

Entering a destination town

X In the Enter Destination menu, select

the town (

*/$6*2: in the example).

Note

If your destination is in the same town as that displayed, you can continue directly with entering the road/centre.

2004

X Confirm your selection by pressing

the rotary control/push button .

2006

The data entry menu for the town appears.

X Turn the rotary control/push button

and then press the rotary control/ push button to select each letter one after the other.

Navigation mode

2007

Note

Select the symbol to delete the last character in the entry.

The last letter entered is highlighted. To help, the name of the location closest to the previous entry appears. The Traffic Pro offers only the possible remaining letters for selection. If no other entries are available, the Traffic Pro completes the town name automatically.

Accept entry:

X In the data entry menu, select the

symbol.

X Press the rotary control/push button

and hold it down for at least 2 seconds.

If the complete town name has already been entered or completed automatically, the unit will either switch automatically to either the town distinguishing list or you can continue directly with entering the road/centre. If an incomplete town entry has been confirmed, the town selection list appears.

2008

X Turn the rotary control/push button

and then press the rotary control/push button to select the required town.

If the entry made is unambiguous, you can continue directly with entering the road/centre.

The town distinguishing list appears if the selection is ambiguous.

2008

X Turn the rotary control/push button

and then press the rotary control/push button to select the required town.

You can now continue with entering the road/centre.

Selecting destination via postcode

You can also select a destination via its postcode.

X In the Enter Destination menu, select

3RVWDOFRGH.

2009

X Confirm your selection by pressing

the rotary control/push button .

Navigation mode

2010

2011

The data entry menu for the postcode appears.

X Turn the rotary control/push button

and then press the rotary control/ push button to select the numbers and letters one after the other.

Accept entry:

X In the data entry menu, select the

symbol.

X Press the rotary control/push button

and hold it down for at least 2 seconds.

If you have entered an incomplete postcode, the postcode selection list appears.

X Turn the rotary control/push button

and then press the rotary control/ push button to select the required postcode.

The display then shows either the destination corresponding to the postcode in the Enter Destination menu or, if the postcode is shared among several towns, a list containing these towns.

2012

X Turn the rotary control/push button

and then press the rotary control/push button to select the required town.

You can now continue with entering the road/centre.

Entering the destination road

X In the Enter Destination menu, select

6WUHHW.

2013

X Confirm your selection by pressing

the rotary control/push button .

2014

The data entry menu for the road appears or, if fewer than 10 roads are available in the town, the unit switches directly to the road list.

X Turn the rotary control/push button

and then press the rotary control/push button to select each letter one after the other.

2015

Navigation mode

2016

The last letter entered is highlighted. To help, the name of the road closest to the previous entry is displayed. The Traffic Pro offers only the possible remaining letters for selection. If no other entries are available, the Traffic Pro completes the road name automatically.

Accept entry:

X In the data entry menu, select the

symbol.

X Press the rotary control/push button

and hold it down for at least 2 seconds.

If you have entered an incomplete road name, the road list appears.

X Turn the rotary control/push button

and then press the rotary control/push button to select the required road.

You can now start route guidance by selecting

6WDUW URXWH JXLGDQFH or enter a

house number/junction for the road entered.

Entering the destination town centre

Instead of navigating directly to a road, you can also navigate to a town centre.

X In the Enter Destination menu, select

&HQWUH.

2017

X Confirm your selection by pressing

the rotary control/push button .

2018

The data entry menu for the centre appears or, if fewer than 10 centres are available in the town, the unit switches directly to the centre list.

X Turn the rotary control/push button

and then press the rotary control/push button to select each letter one after the other.

Navigation mode

2019

The last letter entered is highlighted. To help, the name of the centre closest to the previous entry is displayed. The Traffic Pro offers only the possible remaining letters for selection. If no other entries are available, the Traffic Pro completes the centre name automatically.

Accept entry:

X In the data entry menu, select the

symbol.

X Press the rotary control/push button

and hold it down for at least 2 seconds.

If you have entered an incomplete centre name, the centre list appears.

2020

X Turn the rotary control/push button

and then press the rotary control/push button to select the required centre.

You can now start route guidance by selecting

6WDUWURXWHJXLGDQFH.

Entering house number for destination road

Note

A house number can only be selected if this information is stored on the navigation CD.

X In the Enter Destination menu, select

+RXVHQXPEHU.

2021

X Confirm your selection by pressing

the rotary control/push button .

2022

A list containing ranges of house numbers appears.

X Turn the rotary control/push button

and then press the rotary control/push button to select the required range.

You can now start route guidance by selecting

Selecting junction for destination road

Note

A junction can only be selected if this information is stored on the navigation CD.

X In the Enter Destination menu, select

6WDUWURXWHJXLGDQFH.

,QWHUVHFWLRQ.

Navigation mode

2023

2024

X Confirm your selection by pressing

the rotary control/push button .

A list of junctions appears.

Note

If the destination road entered crosses more than 9 roads, a data entry menu corresponding to the data entry menu for roads appears.

X Turn the rotary control/push button

and then press the rotary control/push button to select the required junction.

Setting the route options

You can use the route options to specify how the Traffic Pro calculates the route to the destination.

X In the Enter Destination menu,

depending on the previous setting, select

5RXWH VKRUW, 5RXWH IDVW or 5RXWH

G\QDPLF

2025

Confirm your selection by pressing the rotary control/push button .

2026

The Route Options menu appears.

X Turn the rotary control/push button

to select one of the following options:

'\QDPLFURXWH, 4XLFNURXWH, 6KRUWURXWH, $YRLGPRWRUZD\, $YRLGWXQQHO, $YRLGWROO, $YRLGIHUU\ or 5HDG\

X Turn the rotary control/push button

to switch the required function on ( ) or off ( ).

Note:

Only one of the three settings (

URXWH

,4XLFN URXWH or6KRUWURXWH) may be

'\QDPLF

active ( ) at the same time.

•

'\QDPLFURXWH

The route is calculated taking into account the traffic announcements received. If dynamic route guidance is active, the routes are calculated on the basis of the fastest route to the destination.

Navigation mode

Notes:

• Dynamic route guidance is not possible in all countries at present.

• When new route calculations are made with active dynamic route guidance, the Traffic Pro may request the navigation CD (if it is not already inserted).

• 4XLFNURXWH With this setting, the route with the shortest possible travel time to the destination is calculated.

•

6KRUWURXWH

With this setting, the route with the shortest possible distance to the destination is calculated.

•

$YRLG PRWRUZD\, $YRLG WXQQHO,$YRLGWROO

and$YRLGIHUU\ You can use these entries for example to exclude ferries or motorways from the route calculation. The Traffic Pro will then attempt to calculate a route which does not contain any motorways or ferries.

Notes:

• Routes without motorways can only be calculated for short distances (up to 200 km depending on digitalisation density).

•Even if

$YRLGWROO is selected, toll roads

(e.g. in Switzerland or Austria) will be included in the route calculation.

Saving/Deleting route options

X In the Route Options menu, select

5HDG\.

X Confirm your selection by pressing

the rotary control/push button .

X Press .

You can now start route guidance

Saving a destination

Once you have entered a destination, you can save it in the address book. This may be useful if you wish to travel to this destination again at a later date.

X In the Enter Destination menu, select

6DYHGHVWLQDWLRQ.

2027

X Confirm your selection by pressing

the rotary control/push button .

Proceed as described in “Saving an entry in the address book” on page 36.

Navigation mode

Navigation fast access

In navigation fast access mode, the last 50 destinations to which the vehicle has travelled are displayed. The destinations 1 - 20 are numbered for selection using the voice control. You may:

• Start navigation directly to these destinations

• Protect the entries in fast access, i.e. the entry will not be deleted when the maximum number of destinations is reached. The oldest unprotected entry will be deleted.

• Delete individual fast access entries.

• Delete the entire fast access list.

• Save an entry from the fast access list to the address book.

X Press .

2002

The navigation fast access function appears.

Navigating from fast access

X Call up the navigation fast access

function.

X Turn the rotary control/push button

and then press the rotary control/push button to select the required target from

the list. Route guidance to this destination will be started immediately.

Protecting an entry

X Call up the navigation fast access

function.

X Select the entry to be protected. X Press the rotary control/push button

until a menu appears.

X Select the 3URWHFWHQWU\ entry. X Switch protection on ( ) or off ( )

by pressing the rotary control/push button .

Protected entries are identified by the

symbol.

Note:

A protected entry is only protected from being deleted in fast access mode. However, you can delete this protected entry individually, and it will also be deleted when the complete list is deleted.

Navigation mode

Deleting an entry

X Call up the navigation fast access

function.

X Select the entry to be deleted. X Press the rotary control/push button

until a menu appears.

X Turn the rotary control/push button

and then press the rotary control/push

button to select the The entry is deleted from the fast access list.

'HOHWHHQWU\ entry.

Deleting a list

X Call up the navigation fast access

function.

X Press the rotary control/push button

until a menu appears.

X Turn the rotary control/push button

and then press the rotary control/push button to select the

'HOHWHOLVW entry.

2028

X When the prompt appears, select <HV

to delete the list or 1R to retain it. If you select in the fast access function.

<HV, the list will be deleted

Saving an entry in the address book

X Call up the navigation fast access

function.

X Select the entry to be saved. X Press the rotary control/push button

until a menu appears.

X Turn the rotary control/push button

and then press the rotary control/push button to select the

6DYHLQDGGUHVVERRN

entry.

2029

X Turn the rotary control/push button

to select one of the following options:

&UHDWHQHZHQWU\ or $PHQGHQWU\

X Confirm your selection by pressing

the rotary control/push button .

Navigation mode

2030

• &UHDWHQHZHQWU\ Select this option to create a new entry in the address book.

•

$PHQGHQWU\

Select this option to add the current address to an existing entry in the address book.

Creating a new entry

X Select the &UHDWHQHZHQWU\ entry.

X Turn the rotary control/push button

and then press the rotary control/push button to select each letter in the surname one after the other.

Note:

Please also refer to the description in “Data entry menus” on page 13.

X In the data entry menu, select the

symbol.

X Press the rotary control/push button

and hold it down for at least 2 seconds.

The entry is adopted.

2031

X Turn the rotary control/push button

and then press the rotary control/push button to select each letter in the first name one after the other.

X In the data entry menu, select the

symbol.

X Press the rotary control/push button

and hold it down for at least 2 seconds.

2032

The address book entry appears.

X Turn the rotary control/push button

and then press the rotary control/push button to select the

6DYH entry.

A confirmation that the entry has been saved appears.

X Press the rotary control/push button

Adding data to entries

X Select the $PHQGHQWU\ entry.

2032

X Turn the rotary control/push button

and then press the rotary control/push button to select the entry to which you wish to add data.

Note:

If there are more than 10 entries in the address book, the data entry menu for locating the required name appears.

Navigation mode

2034

The navigation address previously selected is added to the selected address book entry.

If the selected address book entry already contains an address, the following prompt appears:

X In the prompt, select <HV to overwrite

the existing address or

1R to retain the

address.

If you select

<HV, the existing address

will be overwritten.

Selecting a destination from the address book

You can find a destination in the address book and start navigation to it.

X In the Navigation main menu, select

the

'HVWIURPDGGERRN entry.

2035

X Confirm your selection by pressing

the rotary control/push button .

2036

The address book entries which support navigation appear.

Note:

If there are more than 9 entries in the address book, the data entry menu for locating the required name appears.

X Turn the rotary control/push button

and then press the rotary control/push button to select the required entry.

Route guidance to this destination will be started immediately.

Navigation mode

2037

2038

Point of interest

You can select a POI as a main destination or a stopover. POIs include petrol stations, airports or hospitals, for example.

X In the Navigation main menu, select

the

6SHFLDO'HVW entry.

X Confirm your selection by pressing

the rotary control/push button .

or if route guidance is already active

X In the navigation status display, press

the rotary control/push button .

The Options menu appears.

X Select the 6WRSRYHU entry. X Confirm your selection by pressing

the rotary control/push button .

X Select the 6SHFLDO'HVW entry.

2039

X Confirm your selection by pressing

the rotary control/push button .

2040

The POI menu appears.

X Turn the rotary control/push button

to select one of the following options:

,QYLFLQLW\RIORFDWLRQ, ,QFRXQWU\, ,QYLFLQLW\RIGHVWLQDWLRQ or ,QSODFH

X Confirm your selection by pressing

the rotary control/push button .

•

,QYLFLQLW\RIORFDWLRQ

You can select a POI in the vicinity of the vehicle. When you make your selection, the unit will tell you in which direction the POI is located and how far away it is.

•

,QFRXQWU\

You can select a POI for the selected country from a range of national POI categories.

•

,QYLFLQLW\RIGHVWLQDWLRQ

You can select a POI in the vicinity of the destination.

Note:

The ,QYLFLQLW\RIGHVWLQDWLRQ entry can only be selected if route guidance is active.

•

,QSODFH

You can select a POI in a specific town.

Navigation mode

Old version

2042

2043

Local

X In the POI menu, select the ,QYLFLQLW\RI

ORFDWLRQ

entry.

X Confirm your selection by pressing

the rotary control/push button .

X Turn the rotary control/push button

and then press the rotary control/push button to select the required POI category.

The data entry menu for POIs appears or, if fewer than 10 POIs are available in the selected category, the unit switches directly to the POI list.

X Turn the rotary control/push button

and then press the rotary control/push button to select each letter one after the other.

Accept entry:

X In the data entry menu, select the

symbol.

X Press the rotary control/push button

and hold it down for at least 2 seconds.

2044

X Turn the rotary control/push button

and then press the rotary control/push

button to select the required POI. Route guidance to the selected point of interest is initiated.

In country

X In the POI menu, select the ,QFRXQWU\

entry.

2045

X Confirm your selection by pressing

the rotary control/push button .

2046

X Turn the rotary control/push button

and then press the rotary control/push button to select the country in which you are looking for a national POI.

2047

X Turn the rotary control/push button

and then press the rotary control/push button to select the required POI category.

Navigation mode

2053

2049

The data entry menu for POIs appears or, if fewer than 10 POIs are available in the selected category, the unit switches directly to the POI list.

X Turn the rotary control/push button

and then press the rotary control/push button to select each letter one after the other.

Accept entry:

X In the data entry menu, select the

symbol.

X Press the rotary control/push button

and hold it down for at least 2 seconds.

X Turn the rotary control/push button

and then press the rotary control/push

button to select the required POI.

Route guidance to the selected point of interest is initiated.

Local area of destination

X In the POI menu, select the ,QYLFLQLW\RI

GHVWLQDWLRQ

entry.

2055

X Confirm your selection by pressing

the rotary control/push button .

Proceed as described in “Local” on page 40. If this option is selected, however, no directions or distances will appear in the POI list.

In place

X In the POI menu, select the ,Q SODFH

entry.

2050

X Confirm your selection by pressing

the rotary control/push button .

2051

X Select the desired country as described

under “Selecting a country” on page 28.

X Select the required town as described

under “Entering a destination town” on page 28.

X Select the required postcode as

described under “Selecting destination via postcode” on page 29.

Navigation mode

2052

2053

X Turn the rotary control/push button

and then press the rotary control/push button to select the required POI category.

The data entry menu for POIs appears or, if fewer than 10 POIs are available in the selected category, the unit switches directly to the POI list.

X Turn the rotary control/push button

and then press the rotary control/push button to select each letter one after the other.

Accept entry:

X In the data entry menu, select the

symbol.

X Press the rotary control/push button

and hold it down for at least 2 seconds.

2054

X Turn the rotary control/push button

and then press the rotary control/push

button to select the required POI.

Route guidance to the selected point of interest is initiated.

Information about points of interest

You can call up additional information about many POIs, e.g. a brief description or a telephone number. You can then also call this number directly. To do this, you must be in the POI list.

2044

X Press and hold it down until the

information appears.

2056

*Only available for the Traffic Pro with Bluetooth® wireless technology.

Navigation mode

X Turn the rotary control/push button

to scroll through the information.

Note:

To call a displayed number directly, select the number and press the rotary control/push button .

X Press to return to the list of POIs.

During route guidance

During route guidance, navigation information is displayed on the status screen in all operating modes. However, complete navigation information is only displayed in the navigation status screen.

Examples:

2057

The navigation status screen.

1004

The radio status screen with active navigation. The display for other sources is similar. When you are approaching a turn, the navigation status screen appears automatically. Once you have completed the turn, the unit reverts to the previous status screen.

Navigation status screen

All information relevant to information is displayed on the navigation status screen.

2057

The distance to the next turn and the estimated time of arrival are shown on the right-hand side of the display. The name of the road the vehicle is turning into appears in the first line on the upper left of the display. The name of the road the vehicle is currently travelling along appears in the second line. Depending on the setting, the current time, estimated journey time remaining or distance remaining to be travelled appear on the bottom left of the display.

Navigation mode

2057

2058

2059

X Turn the rotary control/push button

to select the various displays in the

status display.

Display with current time.

Display with estimated journey time remaining.

Display with distance remaining to be travelled.

Example navigation displays

Warning

Accident hazard

Road traffic regulations always take priority when a vehicle is being driven in traffic. The navigation system is only an aid. Errors may occur in individual data items/entries. At all times, the driver must decide whether or not to heed the information provided. We do not accept liability for erroneous data provided by the navigation system.

• “If possible, please turn back.”

2060

You are driving in the wrong direction

and should turn around at the earliest

opportunity.

• “Please turn left after 100 metres.”

2061

The name of the road the vehicle is turning into appears in the first line on the upper left of the display. The name of the road the vehicle is currently travelling along appears in the second line.

• “Please leave the roundabout at the third exit on the right.”

2062

This display shows you the exit you should take on the roundabout.

Navigation mode

2063

2064

2065

• “Please follow the direction arrows.”

This display tells you that you are currently on a non-digitised road (i.e. car park, garage, multi-storey car park). Your location therefore does not appear on the digitised road map. The arrow indicates the direction of the destination as the crow flies.

• Active stopover:

• Block active:

• Recalculating route:

2066

• Destination reached:

2067

Options menu

During route guidance, you can call up the Options menu in the navigation status screen.

X Press the rotary control/push button

2068

The Options menu appears on the righthand side.

X Turn the rotary control/push button

to select one of the following options:

&DQFHO, 0HVVDJHV, 5RXWHOLVW, 6WRSRYHU (stopover), %ORFN, 5RXWHRSW or $QQRXQFH

X Confirm your selection by pressing

the rotary control/push button .

Navigation mode

• &DQFHO You can abort the current route guidance. See “Cancelling route guidance” on page 46.

•

0HVVDJHV

You can display/listen to a list of traffic announcements relevant to the route. See “Traffic announcements” on page 47.

•

5RXWHOLVW

You can display the route planned by the Traffic Pro. See “Route list” on page 47.

•

6WRSRYHU

You can enter another destination as a stopover during active navigation. See “Stopover” on page 47.

•

%ORFN

You can block a section of the route still to be travelled. See “Blocking a route” on page 49.

5RXWHRSW

• You can modify the route options during navigation. See “Modifying route options” on page 49.

•

$QQRXQFH

You can switch navigation announcements off and then back on again. See “Switching navigation announcements on/off” on page 50.

Cancelling route guidance

You can use this function to cancel route guidance before reaching the actual destination.

X In the Options menu, select the &DQFHO

entry.

2068

X Select <HV (cancel navigation) or 1R

(continue with navigation).

Note:

If no operator inputs are made, the menu will automatically disappear after a few seconds and navigation will continue.

Navigation mode

2069

Traffic announcements

You can display/listen to a list of traffic announcements relevant to the route.

X In the Options menu, select the 0HV

VDJHV

entry.

The list of traffic announcements relevant to the route appears.

X To listen to all announcements, select

the

5HDGRXWDOOPHVVDJHV entry.

X Select the required announcement. X Confirm your selection by pressing

the rotary control/push button .

The announcement appears in full.

For more information about traffic announcements, see “Displaying traffic information” on page 54.

Route list

You can display the route planned by the Traffic Pro.

X In the Options menu, select the 5RXWH

OLVW

entry.

2070

A list of the roads to the destination appears. The distance to be travelled along each road appears after its name.

X Turn the rotary control/push button

to scroll through the list.

Note:

Once route guidance has started, it takes a little while for the route list to appear in full. If the route list is not available due to recalculation, appears. For technical reasons, distance information cannot be displayed for the road currently being driven on.

1RURXWHOLVWDYDLODEOH

X Press to exit the route list.

Stopover

You can enter another destination as a stopover during active navigation.

X In the Options menu, select the 6WRS

RYHU

entry.

2039

X Turn the rotary control/push button

to select one of the following options:

(QWHUDGGUHVV, $GGERRN, 6SHFLDO'HVW or 5DSLGDFFHVV

X Confirm your selection by pressing

the rotary control/push button .

Navigation mode

• (QWHUDGGUHVV You can enter a complete address as a stopover as described in “Entering a destination” on page 27.

•

$GGERRN

You can enter an address book entry as a stopover as described in “Selecting a destination from the address book” on page 38.

•

6SHFLDO'HVW

You can enter a POI as a stopover as described in “Point of interest” on page 39.

•

5DSLGDFFHVV

You can enter a fast access destination as a stopover as described in “Navigation fast access” on page 35.

Once the stopover has been selected, the route is recalculated and route guidance started to the stopover.

Note:

Once the stopover has been reached, the following display appears.

2071

Route guidance to the main destination is started automatically.

Deleting a stopover

If you have entered a stopover, you can delete it before reaching it.

X In the Options menu, select the 6WRS

RYHU

entry again.

2072

X Select <HV (delete stopover) or 1R

(retain stopover).

Note:

If no operator inputs are made, the menu will automatically disappear after a few seconds and the stopover will be retained.

<HV is selected, the stopover is deleted

and route guidance to the main destination started automatically.

Navigation mode

2073

Blocking a route

You can use this function to block a section of the route still to be travelled when the next junction is reached. If possible, the Traffic Pro will then calculate a diversion route. This may be useful if a traffic jam or road block lies immediately ahead.

X In the Options menu, select the %ORFN

entry.

X Turn the rotary control/push button

to select the required distance to be blocked.

X Confirm your selection by pressing

the rotary control/push button .

The route is recalculated.

Unblocking a route

Once a block has been entered, it can be removed again.

X In the Options menu, select the %ORFN

entry.

2074

X Select <HV (delete block) or 1R (retain

block).

Note:

If no operator inputs are made, the menu will automatically disappear after a few seconds and the block will be retained.

Modifying route options

You can modify the route options during navigation.

X In the Options menu, select the 5RXWH

RSW

entry.

2075

X Select '\QDPLF URXWH 4XLFN URXWH, 6KRUW

URXWH

or the avoid functions (on = ).

Note:

Only one of the three settings (

URXWH 4XLFN URXWH

, 6KRUW URXWH) may be active ( ) at the same time. For more information about route options, see “Setting the route options” on page 33.

X In the Route Options menu, select

5HDG\.

The route is calculated with the new route options.

'\QDPLF

Navigation mode

Switching navigation announcements on/off

You can switch navigation announcements off and then back on again.

X In the Options menu, select the

$QQRXQFH entry.

X Press the rotary control/push button

to switch navigation announcements on () or off ().

Information during route guidance

Displaying destination information

X Press . X Turn the rotary control/push button

clockwise until

on the top right of the display.

'HVWLQDWLRQ appears

2076

The following information appears:

• On the top left, the destination town and destination road.

• To the left underneath the destination town, the average speed thus far.

• Above the image of the car, the distance still to be travelled and the anticipated time of arrival.

• To the left and right of the image of the car, the distance already travelled and the journey time thus far.

Notes:

• If a stopover is active, information about it is displayed. appears on the display above the car.

• Press the rotary control/push button

to reset the values for the average speed, distance travelled and journey time thus far to zero.

• By pressing the button for a long time you can obtain a display of all the information concerning the destination shown.

• Exit the destination information by pressing the button.

Navigation mode

2077

Displaying/Storing position

X Press . X Turn the rotary control/push button

clockwise until top right of the display.

The following information appears:

• If possible, the town and road/geographical coordinates and height above sea level (only in the event of sufficient satellite reception) appear on the lefthand side of the display.

• The number of satellites which have been/can be received appears above the image of the car.

3RVLWLRQ appears on the

X Press the rotary control/push button

to store the current position.

2078

The current position was saved in fast access mode.

Displaying traffic announcements

X Press . X Turn the rotary control/push button

clockwise until

the top right of the display.

70& appears on

2079

The following information appears:

• The number of TMC messages received.

• The number of TMC messages relevant to the route.

X Press the rotary control/push button

2069

All TMC messages are displayed.

X To listen to all announcements, select

the

5HDGRXWDOOPHVVDJHV entry.

X Select the required announcement. X Confirm your selection by pressing

the rotary control/push button .

The announcement appears in full.

For more information about traffic announcements, see “Displaying traffic information” on page 54.

Navigation mode

2081

2082

Displaying/Changing route settings

X Press . X Turn the rotary control/push button

clockwise until right of the display.

The current route settings are displayed.

X Press the rotary control/push button

X Select '\QDPLF URXWH 4XLFN URXWH, 6KRUW

or the avoid functions (on = ).

URXWH

5RXWH appears on the top

Note:

Only one of the three settings (

URXWH 4XLFN URXWH

, 6KRUW URXWH) may be

'\QDPLF

active ( ) at the same time. For more information about route options, see “Setting the route options” on page 33.

The route is calculated with the new route options.

Information during non-active route guidance

Displaying/Storing a position

You can display and store the current position. See “Displaying/Storing position” on page 51.

Displaying TMC messages

You can display TMC messages as described in “Displaying traffic announcements” on page 51. Of course, no traffic announcements are displayed for the route.

Dynamic route guidance with TMC

Note:

Dynamic route guidance is not possible in all countries. When Dynamic Route Guidance is active, the navigation system may request the navigation CD for possible route calculation (if the navigation CD is not inserted).

What is dynamic route guidance?

Dynamic route guidance is used to calculate the route, taking current traffic announcements into account. The traffic announcements are transmitted by a TMC radio station in addition to the radio programme and are received and analysed by the navigation system. The reception of traffic announcements is free of charge.

Navigation mode

Note:

As the traffic announcements are transmitted by radio stations, we cannot assume responsibility for the completeness or accuracy of the announcements.

Austria: The location and event code was made available by ASFINAG and BMVIT.

Dynamic route guidance

You can activate dynamic route guidance by selecting route options. If dynamic route guidance has been activated, a continuous check is made for the presence of relevant announcements for the selected route. The route is then calculated using the “fast route” option, while taking into account current traffic announcements. If it is determined during these continuous checks that a traffic announcement is of relevance for the route guidance, the unit will automatically re-calculate a new route to the destination.

1HZURXWH is shown on the display. There

is also the voice announcement “The route is being recalculated due to current traffic announcements”.

'\QDPLF URXWH in the

Note:

If no TMC stations are received for 10 minutes,

'\Q URXWH JXLG QRW SRVVLEOH

1R 70& UHFHSWLRQ DW SUHVHQW

is displayed

and a short signal tone sounds.

Your navigation system can receive TMC information, whether a TMC station is selected or not. However, in order to guarantee optimal reception of TMC information, we recommend the selection of a TMC station.

Navigation mode

Displaying traffic information

Current traffic announcements can be displayed in text form. There are several options for requesting current traffic information. You can call up traffic announcements via the navigation Options menu and by pressing . Please refer to the description in “Traffic announcements” on page 47 and “Displaying traffic announcements” on page 51.

Note:

If no up-to-date traffic information is available, 1R70& PHVVDJHV and 1R 70&

RQURXWH

are displayed.

In both cases, the Traffic Pro displays a list of the up-to-date traffic information currently available.

2069

All TMC messages are displayed.

Note:

Traffic announcements are displayed sorted according to category and road. Various symbols appear in front of each traffic announcement to indicate the category.

indicates a warning. indicates building sites and other

obstacles.

indicates traffic jams in general.

X To listen to all announcements, select

the

5HDGRXWDOOPHVVDJHV entry.

X Select the required announcement. X Confirm your selection by pressing

the rotary control/push button .

2084

The announcement appears in full.

X To listen to the announcement, select

the

5HDGRXW entry.

X Turn the rotary control/push button

to scroll through the traffic announcement.

Note:

The reading out of traffic announcements can be aborted by pressing the rotary control/push button .

A typical traffic announcement appears as follows:

• a motorway or road number

• Approximate direction information

• Detailed location and direction information

• The event

• The cause, if known

Navigation mode

2085

2086

Settings

You can make various settings for navigation in the settings.

X In the Navigation main menu, select

the

6HWWLQJ entry.

X Confirm your selection by pressing

the rotary control/push button .

The Settings menu appears.

X Turn the rotary control/push button

to select one of the following options:

7UDIILFPHVVDJHV, $QQRXQFHDUULYDOWLPH, (7$VHWWLQJ or 8QLWRIPHDVXUH

X Confirm your selection by pressing

the rotary control/push button .

•

7UDIILFPHVVDJHV

You can specify whether or not traffic announcements should be read out automatically by the unit and, if so, which ones.

•

$QQRXQFHDUULYDOWLPH

You can specify whether the calculated time of arrival should be announced automatically once the route has been calculated/recalculated.

•

(7$VHWWLQJ

You can configure the calculation of the ETA. ETA stands for Estimated Time of Arrival.

8QLWRIPHDVXUH

• You can convert the calculation of the distances from metric (display in metres and kilometres) to imperial (display in yards and miles) system and vice versa.

Traffic announcements

You can specify whether or not traffic announcements should be read out automatically by the Traffic Pro and, if so, which ones.

X In the Settings menu, select the 7UDIILF

PHVVDJHV

entry.

2086

X Confirm your selection by pressing

the rotary control/push button .

2087

X You may now select $QQRXQFH PHV

VDJHV

, 2QURXWHRQO\ or :DUQLQJVRQO\.

Navigation mode

• $QQRXQFHPHVVDJHV If this function is active, all traffic announcements are made automatically on receipt.

Note:

This setting must be active ( ) in order to be able to activate the two other settings.

•

2QURXWHRQO\

If you activate this function ( ), only the traffic announcements relevant to the route are made.

•

:DUQLQJVRQO\

Activate this function ( ) to have only warnings announced.

X Turn the rotary control/push button

to switch the required function on ( ) or off ( ).

Announcing the time of arrival

You can specify whether the calculated time of arrival should be announced automatically once the route has been calculated/ recalculated or after pressing the button.

X In the Settings menu, select the

$QQRXQFHDUULYDOWLPH entry.

2088

X Press the rotary control/push button

to switch the announcement of the time of arrival on ( ) or off ( ).

ETA setting

You can configure the calculation of the ETA. ETA stands for Estimated Time of Arrival.

X In the Settings menu, select the (7$

VHWWLQJ

entry.

2091

X Confirm your selection by pressing

the rotary control/push button .

2092

X You may now select 6SRUWV FDU, &DU,

9DQ or 6HWIUHHO\.

•

6SRUWVFDU

This setting indicates to the Traffic Pro that you tend to drive rather quickly. An earlier ETA is calculated.

Navigation mode

• &DU This is the default setting. It offers sufficiently accurate calculation of the ETA for most drivers.

•

9DQ

This setting indicates to the Traffic Pro that you will need a little longer for the planned route. This setting could be selected, for example, for a slower vehicle or in dense traffic areas.

•

6HWIUHHO\

Select this option to modify the calculation of the ETA to suit your requirements.

Note:

Only one of the two settings may be active ( ) at the same time.

X Turn the rotary control/push button

to activate the required setting ( ).

6HWIUHHO\ is selected, you still need to

If select the required setting. The available range is between 50% and 200%. A value of 100% indicates the

&DU set-

ting. A later ETA will be calculated if a higher percentage value is selected.

2093

X Turn the rotary control/push button

to set the required percentage value.

X Confirm your selection by pressing

the rotary control/push button .

Measuring unit

You can convert the calculation of the distances from metric (display in metres and kilometres) to imperial (display in yards and miles) system and vice versa.

X In the Settings menu, select the 8QLWRI

PHDVXUH

entry.

2094

X Confirm your selection by pressing

the rotary control/push button .

2095

X Select 0HWULF or ,PSHULDO (on = ).

Note:

Only one of the two settings may be active ( ).

Radio mode

3001

Radio mode

Switching on radio mode

X Press .

Radio mode is activated. The last waveband selected and the last station selected are set.

Calling up the Radio main menu

You can make settings for radio mode in the Radio main menu. The following description assumes that you are in the status display.

X Press twice in succession.

X Press .

The Fast Access menu appears.

X Select the 5DGLRPHQX entry.

The Radio main menu appears. The example shows the Radio main menu for VHF.

X Turn the rotary control/push button

to select one of the following options:

:DYHEDQG, 3URJUDPPHW\SH, )LOWHU, 7UDIILFLQIR, 6RXQG, 9RLFHHQWULHV, 5HJLRQDOLVDWLRQ, 5HFHSWLRQRSWLPLVDWLRQ or $GDSWLYHEDQGZLGWKFRQWURO

X Confirm your selection by pressing

the rotary control/push button .

The required function is called up.

•

:DYHEDQG

Accesses the selection menu for the waveband. See “Selecting a waveband” on page 59.

3URJUDPPHW\SH

• Accesses the selection menu for the programme type. See “Programme type” on page 64.

•

)LOWHU

Accesses the selection menu for the filter function. See “Filter function” on page 62.

•

7UDIILFLQIR

Accesses the selection menu for traffic programmes. See “Traffic programme” on page 67.

•

6RXQG

Accesses the sound settings. See “Sound settings” on page 18.

•

9RLFHHQWULHV

Accesses the selection menu for voice entries. See “Voice entries” on page 66.

•

5HJLRQDOLVDWLRQ

You can switch regionalisation on/off. See “Regionalisation” on page 65.

Radio mode

3002

• 5HFHSWLRQRSWLPLVDWLRQ Accesses the selection menu for reception optimisation. See “Reception optimisation” on page 66.

•

$GDSWLYHEDQGZLGWKFRQWURO

You can switch bandwidth control on/ off. See “Bandwidth control” on page 67.

Selecting a waveband

X In the Radio main menu, select :DYH

EDQG

X Turn the rotary control/push button

to select one of the following options:

)0DOSKDEHWLFDOO\, )0E\TXDOLW\, 6WDWLRQPHPRU\, $0 or 6KRUWZDYH

X Confirm your selection by pressing

the rotary control/push button .

The selected waveband is set.

)0DOSKDEHWLFDOO\

• If an FM station was selected previously, it will remain selected or, if an AM station was selected, the last FM station selected will be set. The Fast Access menu appears. All receivable stations which are not filtered out, appear in the list in alphabetical order. The waveband set is indicated by the

symbol in the status display.

•

)0E\TXDOLW\

If an FM station was selected previously, it will remain selected or, if an AM station was selected, the last FM station selected will be set. The Fast Access menu appears. All receivable stations which are not filtered out, appear in the list in order of quality. The waveband set is indicated by the

symbol in the status display.

6WDWLRQPHPRU\

• The last station set is retained. The station memory, which can store up to 20 FM and AM waveband stations, is displayed. The waveband set is indicated by the

symbol in the status display.

See “Station memory” on page 71.

•

The last medium wave station selected is set. The status display appears. The waveband set is indicated by the

symbol in the status display.

•

6KRUWZDYH

The last short wave station selected is set. The status display appears. The waveband set is indicated by the

symbol in the status display.

Radio mode

FM mode

FM mode combines the two wavebands

)0DOSKDEHWLFDOO\ and )0E\TXDOLW\.

Possible settings for FM stations

A number of possible settings may be made for selecting stations in FM mode:

• Tuning via station list. See “Station list” on page 60.

• Scan function. See “Scan function” on page 61.

• Manual station tuning. See “Manual station tuning” on page 62.

• Via the station memory. See “Station memory” on page 71.

Station list

All stations which can be received/identified appear in the station list. The display sequence is determined by the selected waveband

)0DOSKDEHWLFDOO\

or )0E\TXDOLW\.

Stations can be selected using the station list in two ways:

Selection in status display:

X Turn the rotary control/push button

clockwise or counter clockwise.

X In the status display, press or

3003

Press or turn the rotary control/ push button to the right to select the next station on the station list. The name of the station appears underneath the station currently selected.

Press or turn the rotary control/

push button to the left to select the previous station on the station list. The

name of the station appears above the station currently selected.

Selection via fast access.

X Press .

3004

The Fast Access menu appears.

X Turn the rotary control/push button

to select the required station and press the rotary control/push button .

The selected station is set.

Radio mode

Notes:

• If the selected entry is a station chain, this is indicated by a small triangle on the right-hand edge of the list. Once a station has been selected, a second list appears from which you may select the required station from the station chain. Press to return to the previous menu without selecting a station.

• Similarly, if a station transmits a number of different regional programmes and regionalisation has been activated as described in “Regionalisation” on page 65, a list will appear from which you may select the required station. Stations of this type are identified in the station list by

5(*.

Scan function

All stations in the station list are scanned briefly to enable you to select the one you require.

X In the status display, press and hold

down or .

X In the status display, press the rotary

control/push button .

The Options menu appears.

X Select the 6FDQ entry. X Press the rotary control/push button

to activate the function ( ). The stations in the station list are scanned briefly in descending/ascending order.

Note:

If the station memory is active and an FM station is selected, then only stations which have not yet been stored are played when using the scan function.

Aborting the scan function

X In the status display, press or

X Turn the rotary control/ push button

X In the status display, press the rotary

control/push button .

The Options menu appears.

X Select the 6FDQ entry. X Press the rotary control/push button

to deactivate the function ( ). The station currently being scanned is set and the scan function is aborted.

Radio mode

3005

Manual station tuning

You can set the required frequency manually.

X In the status display, press the rotary

control/push button until



or )UHTXHQF\ appears on the display

)UHTXHQF\

instead of the previous/next station.

X Turn the rotary control/push button

to select the required frequency. To exit manual station tuning, press and hold down the rotary control/push button until



disappears.

)UHTXHQF\ or )UHTXHQF\

The selected frequency remains set.

Note:

Press or to initiate the search for the next receivable station. Pressing and holding button or

results in a fast frequency search

until the button is released.

Filter function

You can use this function to filter stations or entire station chains out of the station list.

X In the Radio main menu, select )LOWHU.

3006

The Filter menu appears.

X Turn the rotary control/push button

to select one of the following options:

)LOWHU, 5HVHW or

the stations and station chains which can currently be received.

Switching the filter function on/off

X In the Filter menu, select the )LOWHU

entry.

X Turn the rotary control/push button

to switch the function on ( ) or off

(). If the function is active ( ), only the stations and station chains which have not been filtered out will appear in the FM station lists.

Note:

If the function is not active, the filter settings will continue to be maintained.

Radio mode

Filtering stations

X In the Filter menu, select the station

chain to be filtered out and press the rotary control/push button .

X Select the HQWLUHVWDWLRQFKDLQ entry. X Turn the rotary control/push button

to switch the function on ( ).

X Press . X In the Fast Access menu which

appears, select the station chain to be filtered.

X Press the rotary control/push button

until a menu appears.

X Select the )LOWHUVWDWLRQFKDLQ entry.

The selected station chain no longer appears in the station list.

Filtering stations

X In the Filter menu, select the station to

be filtered.

X Turn the rotary control/push button

to activate the filter for this station ( ).

X Press . X In the Fast Access menu which

appears, select the station to be filtered.

X Press the rotary control/push button

until a menu appears.

X Select the )LOWHUVWDWLRQ entry.

X To filter the station currently playing,

press the rotary control/push button in the status display.

X Select the )LOWHU entry. X Turn the rotary control/push button

to activate the filter for this station ( ). The selected station no longer appears in the station list.

Cancel filtering Cancel all filters

X In the Filter menu, select the 5HVHW

entry.

Deleting station chain filters

X In the Filter menu, select the station

chain to be activated and press the rotary control/push button .

X Select the HQWLUHVWDWLRQFKDLQ entry. X Turn the rotary control/push button

to switch the filter off ( ).

Deleting station filters

X In the Filter menu, select the station to

be activated.

X Turn the rotary control/push button

to deactivate the filter for this station ().

Radio mode

3007

Programme type

Programme type (PTY) is a service offered by many stations within the radio data system (RDS). It can be used to define which specific stations should be displayed with the corresponding programme types in the station list.

X In the Radio main menu, select 3UR

JUDPPHW\SH

The Programme Type menu appears.

X Turn the rotary control/push button

to select one of the following options:

3URJUDPPHW\SH, 5HVHW, 1R37< or

the PTY categories displayed.

Switching the programme type function on/off

X In the Programme Type menu, select

the

3URJUDPPHW\SH entry.

X Turn the rotary control/push button

to switch the function on ( ) or off

(). If the function is active ( ), only the stations with the selected programme types appear in the FM station lists. The programme type of the selected station also appears on the right of the status display.

Note:

If the function is not active, the settings will continue to be maintained.

Selecting the programme type

X In the Programme Type menu, select

the entry for the required programme

type.

X Turn the rotary control/push button

to switch the individual programme

types on ( ) or off ( ).

Select

5HVHW in the programme type

menu to reset all programme types to off.

Note:

Highlighting

5HVHW and subsequently

pressing and holding the rotary control/ push button , all programme types are reset to on. All PTY categories are displayed in the Programme Type menu. A greyed-out category indicates that no stations in this category can be received at the current time. However, the category can still be activated/deactivated. Activate the

1R37< entry to add stations

which do no transmit any PTY information to the station list display.

Radio mode

3008

Regionalisation

During the transmission time, certain RDS programmes are divided into regional programmes with different programme content. Switching on regionalisation prevents the Traffic Pro from switching between regional programmes with different content.

X In the Radio main menu, select the

5HJLRQDOLVDWLRQ entry.

X Turn the rotary control/push button

to switch the function on ( ) or off ().

Note:

Stations with regional programmes are identified in the station list by 5(*. If you switch the regional function off whilst listening to a regional station, the unit will switch to the associated base station.

Radio text

FM stations supply additional information, e.g. news or information about the current programme, via the RDS data stream. This information can be displayed.

Warning

Accident hazard

Since information transmitted via radio text display varies constantly, we recommend tuning in the radio text only when the vehicle is stationary to avoid unnecessary distraction for the driver. This is a necessary precaution for accident prevention.

X In the status display, press the rotary

control/push button . The Options menu appears.

3009

X Select the 5DGLRWH[W entry.

X Press the rotary control/push button

to activate the function ( ).

3010

The radio text for the current FM station is displayed.

Note:

Unfavourable reception conditions, including interference, can garble or even block the radio text display.

Deactivating radio text

X In the status display, press the rotary

control/push button .

X Select the 5DGLRWH[W entry. X Press the rotary control/push button

to deactivate the function ( ).

Radio mode

3011

Voice entries

You can delete or listen to voice entries assigned to the station. You can also activate or deactivate the voice dialogue for creating new voice entries (see also page 74).

X In the Radio main menu, select 9RLFH

HQWULHV

X Select 5HDGRXWDOOHQWULHV, 'HOHWH DOO

HQWULHV

or 'LDORJXHIRUVDYLQJ.

'HOHWHDOOHQWULHV

•

If 'HOHWHDOOHQWULHV is selected, a prompt

will appear asking you to confirm

whether or not all voice entries should

actually be deleted.

Select

<HV to delete the voice entries or

1R to continue without deletion.

•

'LDORJXHIRUVDYLQJ

If the function is active, when a station

is stored, an automatic dialogue will

appear for assigning a voice entry.

Turn the rotary control/push button

to switch the function on ( ) or off

().

Reception optimisation

You can select one of three settings to suppress reception-related interference.

Note:

This setting is irrelevant for the waveband medium wave and short wave.

X In the Radio main menu, select 5HFHS

WLRQRSWLPLVDWLRQ

3012

X Select $XWRPDWLF, $OZD\VVWHUHR or $OZD\V

PRQR

(on = ).

• 5HDGRXWDOOHQWULHV Select 5HDGRXWDOOHQWULHV to listen to all voice entries associated with radio stations.

Note:

Only one of the entries in the list can be active ( ).

Radio mode

• $XWRPDWLF Setting for normal operation, i.e. depending on reception, the unit switches back and forth from stereo to mono (offers the optimum setting for almost all reception areas).

•

$OZD\VVWHUHR

Setting for exceptional reception conditions - i.e. the unit is constantly set to stereo.

•

$OZD\VPRQR

Setting for reception situations in which reflections constantly occur; i.e. the unit is constantly set to mono.

Bandwidth control

Bandwidth control can be used to improve station reception in difficult reception areas (station A has a neighbouring station B in its immediate vicinity).

X In the Radio main menu, select the

$GDSWLYHEDQGZLGWKFRQWURO entry.

X Turn the rotary control/push button

to switch the function on ( ) or off ().

Traffic programme

If an RDS station broadcasts traffic announcements, it is possible to interrupt audio mode (CD, MP3, etc.), AM mode or mute mode and to switch to the traffic announcements. Moreover, you can listen to one FM station while receiving traffic announcements transmitted by another FM station.

X In the Radio main menu, select 7UDIILF

LQIR

3013

The TP menu appears.

X Turn the rotary control/push button

to select one of the following options:

7UDIILFLQIR, 9ROXPH, 6WDWLRQDXWRPDWLF or

the TP stations displayed.

Radio mode

Switching a traffic programme on/off

X In the TP menu, select the 7UDIILFLQIR

entry.

X Turn the rotary control/push button

to switch the function on ( ) or off ().

X or X In the status display, press the rotary

control/push button .

X Select the 73 entry. X Turn the rotary control/push button

to switch the function on ( ) or off ().

If the TP function is active ( ), the symbol appears in the status display to indicate this.

Selecting a TP station

You can specify whether or not you wish to listen to the traffic news on a specific station.

Automatic

X In the TP menu, select the 6WDWLRQDXWR

PDWLF

entry.

X Turn the rotary control/push button

to switch the function on ( ) or off ().

Note:

When you activate the function, the Traffic Pro will select the station you are currently listening to as the TP station. If this station does not transmit traffic programmes or reception is poor, another station will be selected from the station list.

Manual TP station selection

X In the TP menu, select the station on

which you wish to listen to traffic news.

X Turn the rotary control/push button

to activate the station as the TP station ().

X Press . X In the Fast Access menu which

appears, select the required TP station.

X Press the rotary control/push button

until a menu appears.

X Select the 6HWDV73VWDWLRQ entry.

Note:

If the TP station can no longer be received, the Traffic Pro will activate automatic TP station selection. This will remain active until the selected TP station becomes available again.

Radio mode

3014

TP volume

You can use this function to control the increase in volume for traffic announcements.

X In the TP menu, select the 9ROXPH

entry.

X Turn the rotary control/push button

to select the required value.

Notes:

• A setting of “0” indicates no increase in volume.

• A setting of “10” indicates a significant increase in volume.

Cancelling traffic announcements

You can cancel the reception of traffic announcements.

The following display appears during a traffic announcement.

3015

X Press the rotary control/push button

X Press .

Traffic announcements are cancelled.

AM mode

AM mode combines the two wavebands

$0 and 6KRUWZDYH.

Possible settings for AM stations

A number of possible settings may be made for selecting stations in AM mode:

• Tuning via scan search. See “Scan search” on page 70.

• Scan function. See “Scan function” on page 70.

• Via the station memory. See “Station memory” on page 71.

Radio mode

3016

Scan search

X In the status display, press or

X Turn the rotary control/ push button

Press to search for the next station in ascending frequency order. Press to search for the next station in descending frequency order.

Scan function

All stations which can be received are scanned briefly to enable you to select the one you require.

X In the status display, press and hold

down or .

X In the status display, press the rotary

control/push button .

The Options menu appears.

X Select the 6FDQ entry. X Press the rotary control/push button

to activate the function ( ). The stations which can be received are scanned briefly in descending/ascending frequency order.

Note:

If the station memory is active and an AM station is selected, then only stations which have not yet been stored are played when using the scan function.

Aborting the scan function

X In the status display, press or

X Turn the rotary control/ push button

X In the status display, press the rotary

control/push button .

The Options menu appears.

X Select the 6FDQ entry. X Press the rotary control/push button

to deactivate the function ( ). The station currently being scanned is set permanently and the scan function is aborted.

Radio mode

Station memory

Up to 20 FM, medium wave and short wave stations can be stored in the station memory.

Calling up the station memory

X In the Radio main menu, select :DYH

EDQG

X In the Waveband menu, select the 6WD

WLRQPHPRU\

The stations stored so far are displayed in the fast access station memory.

entry.

Storing stations

You can store the current station if you are already in the station memory or if a different waveband has been selected.

Notes:

• If all 20 memory slots are occupied and a new station is added, the 20th station is deleted from the station memory without warning.

• If a voice entry has been assigned to a station, this is indicated by the symbol in front of the name of the station.

• A station can only be stored once in the memory.

Different waveband set

X In the Fast Access menu (not for AM

waveband), select the station to be stored.

X Press the rotary control/push button

until a menu appears.

3017

X Select the 6DYHVWDWLRQ entry.

X In the status display, press the rotary

control/push button .

The Options menu appears.

X Select the 6DYH entry.

3018

In both cases, the station memory will be displayed. The station to be stored appears as the first entry in the list and is identified by an arrow.

Radio mode

X Turn the rotary control/push button

to select the required memory position.

X Confirm the memory position by press-

ing the rotary control/push button .

Depending on the setting in “Voice entries” on page 66, the procedure for saving a voice entry for the station stored will now start.

The station is now stored in the station memory.

Station already in memory

The station to be stored is already set and you are in station memory fast access mode.

X Turn the rotary control/push button

to select the position in the memory list in which the station to be stored is to be stored.

X Press the rotary control/push button

until a menu appears.

3019

X Select the 6DYH FXUUHQW VWDWLRQ KHUH

entry.

The station is now stored in the station memory.

Depending on the setting in “Voice entries” on page 66, the procedure for saving a voice entry for the station stored will now start.

Moving stations

You can move the position of a station stored in the station memory.

X Turn the rotary control/push button

to select the memory to be moved.

X Press the rotary control/push button

until a menu appears.

3020

X Select the 0RYHVWDWLRQ entry.

The station to be moved is marked with an arrow.

X Turn the rotary control/push button

to select the required memory position.

X Confirm the memory position by press-

ing the rotary control/push button .

Radio mode

3021

Deleting stations

You can delete a station stored in the station memory.

Fast access mode

X Turn the rotary control/push button

to select the station to be deleted.

X Press the rotary control/push button

until a menu appears.

X Select the 'HOHWHVWDWLRQ entry.

The selected station is deleted.

Note:

If a voice entry has been assigned to the deleted station, it will also be deleted.

Status display

X In the status display, press the rotary

control/push button .

The Options menu appears.

X Select the 'HOHWH entry.

The station is deleted from the station memory.

Naming stations

You can assign a user-defined name of up to 8 characters in length to a stored station.

X Turn the rotary control/push button

to select the station to be named.

X Press the rotary control/push button

until a menu appears.

3022

X Select the 1DPHVWDWLRQ entry.

3023

X Select the letters in the required name

one after the other and confirm the name entered.

Note:

Please also refer to the description in “Data entry menus” on page 13.

The station named now appears in the station memory (also in other wavebands) with the name entered.

Radio mode

3024

Creating/Deleting voice entries

You can create a voice entry/delete an existing voice entry for a station stored in the station memory.

Create

Note:

If a voice entry has already been assigned to this station ( symbol) and you wish to change it, you must first delete it before assigning a new entry.

X In fast access mode, turn the rotary

control/push button to select the station for which you wish to create a voice entry.

X Press the rotary control/push button

until a menu appears.

X Select the &UHDWHYRLFHHQWU\ entry.

The procedure for saving a voice entry is launched.

Deleting

X In fast access mode, turn the rotary

control/push button to select the station for which you wish to delete a voice entry.

X Press the rotary control/push button

until a menu appears.

3025

X Select the 'HOHWHYRLFHHQWU\ entry.

A prompt appears for you to confirm if the voice entry should really be deleted.

X Select <HV to delete the voice entry or

1R to continue without deletion.

Reading out voice entries

You can listen to the voice entry for a station stored in the station memory.

X In fast access mode, turn the rotary

control/push button to select the station for which you wish to listen to a voice entry.

X Press the rotary control/push button

until a menu appears.

3026

X Select the 5HDGRXWYRLFHHQWU\ entry.

The voice entry is read out.

Media mode

Media mode includes all sources on the Traffic Pro which can be used to play back audio or MP3 media.

Activating media mode

X Press .

The last source active in media mode is activated if possible.

X Insert an audio CD or MP3 CD.

The Traffic Pro will start to play the inserted CD.

X Insert a micro-drive/memory card

containing audio/MP3 tracks into the designated slot.

The Traffic Pro will start to play the tracks on the micro-drive/memory card inserted.

In all three cases, the media fast access functions will appear on the display briefly. The display will then switch to the status display.

Media fast access functions

The media fast access function displays a list of available CDs and directories for selection. The following description assumes that you are in the status display.

X Press .

4001

The media fast access function appears.

X Turn the rotary control/push button

to select the required medium/source and press the rotary control/push button

Media mode

Notes:

• In fast access mode, the individual CDs, memory cards, sources and directories available are identified by the following symbols:

indicates a CD in the internal

drive. SCD stands for Single CD.

indicates memory cards.

indicates a CD in the CD changer. indicates AUX source. indicates directories.

• If for example there is only one audio CD in the internal drive, in fast access mode, the tracks on that CD are displayed immediately.

• Press and hold down to display the full names (if available) of the individual entries in fast access mode. For a directory, the number of tracks and total playback time are also displayed.

Media mode

4002

Note:

Once the last track on a CD/in a directory has been played, if possible, the next track played by the Traffic Pro will be the first track in the next directory/on the next CD. If no other tracks are available, the first track in the current directory/on the current CD is played.

The required CD, micro-drive/memory card, source or directory is called and, if available, the name of the track on the CD or in the directory is displayed.

X Turn the rotary control/push button

to select the required track and press the rotary control/push button .

The selected track is played.

Notes:

Press and hold to display the full names (if available) of the track entries in fast access mode. The track number and the length of the track will also be displayed. Information on the medium on which the current track is stored will also be shown. If a CD name or directory name is available, it will be displayed. The total number of tracks on the CD/ directory and the total playing time will also be displayed. The track lengths of tracks which have not yet been played back are estimated on the basis of a bit rate of 128 kbit/s.

Media status display

The media status display is the “standard display” for audio mode. All relevant data for audio mode appears in the status display. This includes the following information:

• Type of medium (CD, CD changer and micro-drive/memory card)

• Type of track (audio or MP3)

• Status of scan function, track mix, etc.

• Next and previous track

• Playback time

4003

The example shows the status display for MP3 media on a memory card.

Media mode

Track jump/Track skip

X Press to select the next track or

to select the previous track.

X Turn the rotary control/push button

to select the required track.

Notes:

• You can also select tracks in fast access mode. See “Media fast access functions” on page 75.

• If the current track has only been playing for approximately 10 seconds when track jump is selected, the unit will jump immediately to the previous track. If the current track has been playing for longer than 10 seconds, the unit jumps to the beginning of the current track.

Note:

If track skip reaches the first or the last track in a directory or on a CD, the unit skips to the first or the last track in the current directory or on the CD.

Fast forward/rewind

You can start audible fast forward/rewind.

Notes:

Forward/ reverse is not audible for MP3 tracks.

Forward

X Press until you reach the re-

quired point.

X Release .

Playback will continue at normal speed.

Rewind

X Press until you reach the re-

quired point.

X Release .

Playback will continue at normal speed.

Media mode

4004

Play mode

Play mode includes functions such as track mix (random play function), the scan function and the repeat function.

Calling up the Play Mode menu

X In the media status display, press the

rotary control/push button .

The Options menu appears.

X Turn the rotary control/push button

to select control/push button .

3OD\PRGH and press the rotary

4005

The Play Mode menu appears. Turn the rotary control/push button to select one of the following options:

QRUPDORUGHU, 7UDFNPL[, 6FDQ, 5HSHDWWUDFN,

if an MP3 CD or a CF card with several directories is the active source then

'LUHFWRU\PL[,

if the currently active source is the CD changer:

&'PL[ or 5HSHDW&'

Press the rotary control/push button to switch the individual functions on ( ) or off ( ).

Notes:

• Only one of the functions can be switched on ( ).

• Select

QRUPDORUGHU to delete any other

function which might have been activated and play back the tracks in the normal sequence.

Track mix (random play function)

Activate the function to play back all tracks in the current directory/on the current CD in random sequence.

X Turn the rotary control/push button

to select the

7UDFNPL[ entry in the Play

Mode menu.

X Press the rotary control/push button

to switch the function on ( ) or off ().

Media mode

Notes:

Press or to play the next random track. If the current track has been playing for longer than 8 seconds when is pressed, the unit jumps to the beginning of the current track.

Scan

If the function is activated, all tracks in the current directory or on the current CD are played back for approx. 10 seconds.

X Turn the rotary control/push button

to select the

6FDQ entry in the Play

Mode menu.

X Press the rotary control/push button

to switch the function on ( ) or off ().

Notes:

The function is also aborted by pressing

or . The track currently

playing back then continues.

Repeat track

Activate the function to repeat the current track continuously.

X Turn the rotary control/push button

to select the

5HSHDW WUDFN entry in the

Play Mode menu.

X Press the rotary control/push button

to switch the function on ( ) or off ().

Notes:

Press or to play the next track and deactivate the function. If the track has been playing for longer than 8 seconds when is pressed, the unit jumps to the beginning of the track. The function then remains activated.

CD mix

Notes:

The function is only available if the CD changer is the active source.

Activate the function to play all tracks on the various CDs one after the other in random sequence.

X Turn the rotary control/push button

to select the

5HSHDW&' entry in the Play

Mode menu.

X Press the rotary control/push button

to switch the function on ( ) or off ().

Notes:

Press or to play the next random track. If the current track has been playing for longer than 8 seconds when is pressed, the unit jumps to the beginning of the current track.

Media mode

Repeat CD

Notes:

The function is only available if the CD changer is the active source.

Activate the function to repeat the current CD continuously.

X Turn the rotary control/push button

to select the

5HSHDW&' entry in the Play

Mode menu. Press the rotary control/push button to switch the function on ( ) or off ( ).

Directory mix

Notes:

This function is only available if an MP3 CD or a CF card with directories is the current audio source.

Activate the function to play all tracks on the various directories one after the other in random sequence.

X Turn the rotary control/push button

to select the

'LUHFWRU\PL[ entry in

the Play Mode menu.

Press the rotary control/push button

to switch the function on ( ) or off ( ).

Notes:

Press or to play the next random track. If the current track has been playing for longer than 8 seconds when is pressed, the unit jumps to the beginning of the current track.

Calling up the Media main menu

You can make settings for media mode in the Media main menu. The following description assumes that you are in the status display.

X Press twice in succession.

X Press .

You are now in media fast access mode.

X Select the 0HGLDPHQX entry.

4006

The Media main menu appears.

Media mode

4007

Switching detailed track display on/off

If detailed track display is activated, a previously abbreviated track name/ID3 tag is displayed in full, if possible.

X In the Media main menu, select the

'HWDLOHGWUDFNGLVSOD\ entry.

X Turn the rotary control/push button

to switch the function on ( ) or off

().

CD mode

Notes on compact discs (CD)

Sound interruptions may occur if the CD is soiled. In order to ensure the highest tone quality, please note the following:

Correct

Incorrect

• Always touch the CD at the edges only. Keep the disc clean and never touch the surface.

• Never stick anything on the CD.

• Protect the CDs against direct sunlight and from heat sources such as heaters etc.

Incorrect

Correct

• Before playing the CD, it should be cleaned with a special, commercially available cleaning cloth, wiping from the centre outwards. Solvents such as benzene, thinners or other commercially available cleaners and antistatic sprays must not be used.

Notes:

• The Traffic Pro cannot play back DVD-plus media (one side audio CD, the other DVD). Due to its increased thickness, inserting a DVD-plus may damage the Traffic Pro.

• Please note that foreign bodies such as coins or other objects must not be inserted into the CD slot on the Traffic Pro. Foreign bodies in the unit can damage the Traffic Pro.

Media mode

Inserting/Ejecting CDs

Insertion

X Insert the disc into the CD slot with

the printed side up. The unit pulls in the CD automatically and begins to play the disc from the first track.

Ejecting

X Press .

The CD is ejected.

X Remove the CD.

Notes:

• The CD is not ejected when the unit is switched off but remains in the CD slot.

• If, once it has been ejected, the CD is not removed from the CD slot, it will be pulled back in after a short time.

Notes on CD-R and CD-RWs

You can play CD-Rs (writeable CDs) and CD-RWs (rewriteable CDs) on this unit. However, please comply with legal restrictions. These restrictions may vary from one country to another. Depending upon the recording device used to record the CD-R/CD-RW or the state of the CD-R/CD-RW itself, it may not be possible to play some CD-Rs/CDRWs on this unit. A CD-R/CD-RW must be manufactured according to the “Red Book” standard (not applicable for MP3 CDs).

Notes on copy-protected CDs

In some cases, problems may arise when attempting to play copy-protected CDs, such as long reading times or a total inability to perform playback.

Temperature protection circuit

A temperature protection circuit in the Traffic Pro protects the laser diode from excessive heat. If this protection circuit is triggered, a warning message will appear and a signal tone will sound. The internal CD drive will then be disabled until a cooling down phase has elapsed.

Media mode

MP3 mode

General notes on MP3

The music that can be played when your unit is in MP3 mode is generally copyright-protected under applicable international and national laws. In several countries, the reproduction of copyrighted material is not permitted, even if only for personal use, without the express prior consent of the copyright holder. Please check the current copyright laws for your country and comply with them. These restrictions naturally do not apply to your own compositions and recordings, or for recordings for which authorisation has been obtained from the copyright holder.

Creating an MP3 storage medium

• A maximum of 63 folders, each of which can contain up to 50 tracks, can be stored on a storage medium. However, a maximum of 1000 tracks per medium are supported. If a folder contains more than 50 tracks, a second folder will be created automatically which can also contain up to 50 tracks. Only folder names with 45 characters or fewer can be displayed. Only track names with 63 characters or fewer can be displayed.

• Only MP3 tracks stored on a storage medium in compliance with ISO 9660 can be played.

• If the artist’s name and track title are to be displayed, an ID3 tag must be added to the MP3 file. This unit supports versions ID3v1 and ID3v2. The ID3 tag can only be displayed if the corresponding track is being played. The file name appears first (trackname.MP3).

• The display of artist’s name and track title is restricted to a total maximum length of 63 characters.

• The MP3 formats MPEG1 and MPEG2 Layer3 are supported by the unit. Fixed and variable bit rates of 8 - 320 kbps and scan rates of 16-48 kHz are supported. We recommend the use of the Fraunhofer MP3 Encoder when creating MP3 files.

• We recommend a bit rate of at least 160 kbps for compressing MP3 files. It should be noted that with MP3 files having a variable bit rate, the display of the elapsed playing time may deviate from real time.

• In the case of a mixed-mode medium (partly conventional audio tracks and partly data), only the audio tracks are played back. The data part is not played back, even if MP3 tracks are included.

Media mode

For further information about creating MP3 files and ID3 tags, please consult your dealer or check on the Internet.

Note:

Due to the abundance of different kinds of CD burning software and their associated settings we cannot guarantee the playback quality of MP3 CDs and/or micro-drive/storage cards.

MP3 CD mode

The following points, described in “CD mode” on page 81 apply to MP3 CD mode:

• “Notes on compact discs (CD)” on page 81.

• “Inserting/Ejecting CDs” on page 82.

• “Notes on CD-R and CD-RWs” on page 82.

• “Temperature protection circuit” on page 82.

MP3 memory cards/ Micro-drive mode

Note:

• Micro-drives with a capacity of up to 4 GB can be used.

• Type 1 and type 2 CF cards can be used as memory cards. Memory cards up to a capacity of 4 GB can be used.

• Please note that the storage medium was formatted with the FAT 16 file system.

• Short file names are displayed (8 characters and 3 characters for file extension).

Media mode

Inserting a micro-drive/memory card

The slot for micro-drive/memory cards is located underneath the removable control panel on the Traffic Pro or underneath the cover.

X Remove the control panel as described

in “Removing/Inserting the control panel” on page 15.

X Remove the cover as described in

“Inserting/Removing the cover” on page 16.

X Insert the micro-drive/memory card

into the visible slot on the right-hand side.

Notes:

The memory card/micro-drive can only be inserted in one direction. The reverse of the memory card/micro-drive points to the left.

X Push the micro-drive/memory card

carefully into the slot. This pushes the eject button located above and to the left of the slot outwards.

X Reinsert the cover as described in

“Inserting/Removing the cover” on page 16.

X Reinsert the control panel as described

in “Removing/Inserting the control panel” on page 15.

The micro-drive/memory card is now ready for operation and, if MP3 tracks appear on the micro-drive/memory card, the first track in the first directory is played automatically. If the content of the micro-drive/memory card has not been changed since it was last inserted, playback begins with the last track played.

Removing a micro-drive/memory card

X Remove the control panel as described

in “Removing/Inserting the control panel” on page 15.

X Remove the cover as described in

“Inserting/Removing the cover” on page 16.

X Press the eject button located to the

top left of the slot.

X The micro-drive/memory card is

pushed forwards out of the slot.

X Pull the micro-drive/memory card out

of the slot.

X Reinsert the cover as described in

“Inserting/Removing the cover” on page 16.

X Reinsert the control panel as described

in “Removing/Inserting the control panel” on page 15.

Media mode

CD changer mode

The following points, described in “CD mode” on page 81 apply to CD changer mode:

• “Notes on compact discs (CD)” on

page 81.

• “Notes on CD-R and CD-RWs” on

page 82.

Operational readiness of CD changer

If a CD changer is connected to the Traffic Pro, it will be ready for operation as soon as the CD magazine, loaded with CDs, is inserted. Close the sliding cover after loading. All further operation is performed from the Traffic Pro control panel.

Loading/Ejecting the CD magazine

To eject the CD magazine, open the sliding cover on the changer and press the eject button. The magazine is ejected and can be removed. When inserting CDs into the magazine, please note the instructions printed on the magazine.

Attention:

Incorrectly inserted CDs will not be played.

Note:

To allow for the fastest possible change of CDs, the magazine should be loaded successively, beginning with compartment 1.

External units/AUX mode

You can call up units connected externally to the Traffic Pro as described in “Media fast access functions” on page 75. However, AUX mode must be activated as described in “External device” on page 131.

The external unit cannot be operated. You can only make volume and noise settings for this source.

Telephone mode

Below, you will find information on operating a mobile phone with Bluetooth® wireless technology, connected to the Traffic Pro.

Notes:

• The Traffic Pro can operate a mobile phone equipped with Bluetooth® wireless technology. We support the Bluetooth® wireless technology profile HFP1.0. Mobile phones without Bluetooth® wireless technology cannot be operated.

• It is possible that some of the functions described are not available with some mobile phones equipped with Bluetooth® wireless technology. The Internet page www.becker.de contain additional informations.

• If your mobile telephone is connected to the Traffic Pro and the Traffic Pro is switched off (ignition is still switched on or the ignition key is in the radio position), the Traffic Pro is activated by an incoming call.

Notes:

• The call lists and fast access entries described below always only apply to the time during which the mobile phone, equipped with Bluetooth® wireless technology, was connected to the Traffic Pro. The entries in the call lists of the Traffic Pro are not synchronised with the call lists on the mobile phone.

• The Traffic Pro cannot access the mobile phone’s number memory or the SIM card. However you can import address book entries from the mobile phone, as described in “Importing an address book entry*” on page 110.

• It is only possible to display the name of a caller if the caller is listed in the address book on the Traffic Pro.

Telephone mode*

Warning

Risk of injury

Please ensure that you keep the mobile phone in an appropriate, safe holder. Only then can injuries be prevented in the event of an accident or due to sudden braking.

*Only available for the Traffic Pro with Bluetooth® wireless technology. 87

Telephone mode*

5001

Calling up the telephone

Note:

To call up telephone mode directly, it is essential that Bluetooth has been activated and that the device is connected to a mobile phone with Bluetooth® wireless technology. This is described in “Bluetooth*” on page 115.

X Press .

Telephone mode is activated. The telephone mode fast access functions are displayed. In fast access mode the last 20 numbers or names which have been dialled, answered or rejected will be displayed in chronological order. Further information on fast access can be found under “Fast access telephone functions” on page 98.

Bluetooth not yet switched on

If Bluetooth has not been switched on when you try to call up telephone mode, you will be shown the following message.

5002

X Press the rotary control/push button

X Switch on the Bluetooth function as

described in “Activating/ deactivating Bluetooth*” on page 122.

Bluetooth mobile phone not yet connected

If the mobile phone has not been connected when you try to call up telephone mode, the following message is displayed.

5003

You will see a list containing all the previously connected devices and the entry

/RRNIRUWHOHSKRQH.

1R%7GHYLFHVis displayed in the list, or

if the device to be connected is not displayed, select the entry to search for the device. This is also described in “Searching for Bluetooth devices*” on page 122.

/RRN IRU WHOHSKRQH

88 *Only available for the Traffic Pro with Bluetooth® wireless technology.

Telephone mode*

5001

X Select the device to be connected from

the list.

X Press the rotary control/push button

Then proceed as described in “Connecting devices (Traffic Pro)*” on page 118.

The telephone mode fast access functions are displayed after the mobile phone has been connected successfully.

Calling up the Telephone main menu

In the Telephone main menu, you can enter/ select telephone numbers, call up the call lists, connect a telephone, call the emergency services and call up the telephone settings.

Note:

To call up the telephone main menu directly it is essential that Bluetooth has been activated and that the mobile phone is connected to Bluetooth® wireless technology. This is described in “Bluetooth*” on page 115.

X Press twice in succession.

X Press .

The Fast Access menu appears.

X Select the 7HOHSKRQHPHQX entry.

5004

The Telephone main menu appears.

X Turn the rotary control/push button

to select between

'LDOQXPEHU, &DOOIURPDGGUHVVERRN, &DOOOLVWV, &RQQHFWWHOHSKRQH, (PHUJHQF\FDOO and 6HWWLQJ.

X Confirm your selection by pressing

the rotary control/push button .

The desired function is called up.

•

'LDOQXPEHU

Accesses the input menu for a telephone number. See “Dialling numbers” on page 90.

*Only available for the Traffic Pro with Bluetooth® wireless technology. 89

Telephone mode*

• &DOOIURPDGGUHVVERRN You can select a telephone number from the address book. See “Selecting a number from the address book” on page 91.

•

&DOOOLVWV

You can obtain a display of the call lists for missed calls, answered calls and numbers dialled. See “Call lists” on page 92.

•

&RQQHFWWHOHSKRQH

You can connect a telephone via Bluetooth® wireless technology or start a device search. The operating procedure is the same as described in “Bluetooth mobile phone not yet connected” on page 88.

•

(PHUJHQF\FDOO

You can establish a connection to the “112” emergency number. See “Emergency call” on page 93.

•

6HWWLQJ

You can select call answering settings as well as settings for automatic activation of voice mode. See “Settings” on page 94.

Dialling numbers

Use this function to enter a telephone number and to call this number.

X In the Telephone main menu, select

the entry

'LDOQXPEHU.

5005

The input menu for the telephone number appears.

X Turn the rotary control/push button

and then press the rotary control/ push button to select the digits in the desired telephone number, one after the other.

Note

Select the symbol to delete the last character in the entry. Please also refer to the description in “Data entry menus” on page 13.

Establishing a connection:

X In the input menu, select the 'LDO entry.

X press the rotary control/push button

and hold for at least 2 seconds.

The Traffic Pro indicates that a connection is being established by displaying the following message.

5006

Press the rotary control/push button to abort the call.

90 *Only available for the Traffic Pro with Bluetooth® wireless technology.

Telephone mode*

5007

If the person called answers the telephone the Traffic Pro switches to the status display for active telephone calls.

Note:

If the number called is busy, the following message appears:

X Press the rotary control/push button

Selecting a number from the address book

Use this function to select a telephone number from an address book and to call this number.

X In the Telephone main menu, select

the entry

&DOOIURPDGGUHVVERRN.

5008

The address book entries which have a telephone number are displayed.

Note:

If there are more than 9 entries in the address book, for which one or more telephone numbers are stored, the data entry menu for locating the required name appears.

X Turn the rotary control/push button

and then press the rotary control/ push button to select the desired entry.

If several telephone numbers have been saved in the address book entry the following appears on the display.

5009

Note:

Up to three telephone numbers are displayed and marked with different symbols:

stands for the mobile number. stands for the business number. stands for the private number.

X Turn the rotary control/push button

and then press the rotary control/ push button to select the desired number.

The connection will be established.

*Only available for the Traffic Pro with Bluetooth® wireless technology. 91

Telephone mode*

5010

5007

The Traffic Pro indicates that a connection is being established by displaying the following message.

Press the rotary control/push button to abort the call.

If the person called answers the telephone the Traffic Pro switches to the status display for active telephone calls.

Note:

If the number called is busy, the following message appears:

X Press the rotary control/push button

Call lists

You can obtain a display of the call lists for missed calls, answered calls and numbers dialled.

Notes:

• The call lists described below always only apply to the time during which the mobile phone was connected to the Bluetooth® wireless technology with the Traffic Pro. The entries in the call lists of the Traffic Pro are not synchronised with the call lists in the mobile phone.

• It is only possible to display the name of a caller if the caller is listed in the address book of the Traffic Pro.

• The lists are limited to a maximum of 20 entries.

• If a number is not known it will appear in the list as

8QNQRZQ.

X In the Telephone main menu, select

&DOOOLVWV.

5011

X Turn the rotary control/push

button to select between

0LVVHGFDOOV, 'LDOOHGQXPEHUV and $FFHSWHGFDOOV.

X Confirm your selection by pressing

the rotary control/push button .

The desired list is called up.

•

0LVVHGFDOOV

In this list you will find calls which you missed or which you rejected.

•

'LDOOHGQXPEHUV

In this list you will find calls which you made yourself.

• $FFHSWHGFDOOV In this list you will find calls which you answered.

92 *Only available for the Traffic Pro with Bluetooth® wireless technology.

Telephone mode*

5012

In the right-hand section of the display you can see the time of the entry for the various entries in the list. The date will be displayed if the entries are older.

Calling a number from the list

X Select the list entry you wish to call. X Press the rotary control/push button

. A connection will be established to the desired number.

Retrieving information about the entry

X Select the list entry on which you wish

to receive more information.

X Press and hold until the

information appears.

X Press to return to the list.

Deleting a call list

You can delete the entire call list.

X Select 'HOHWH OLVW in the call list to be

deleted.

5013

X Select <HV (delete) or 1R (do not

delete). If you select deleted.

<HV, the call list will be

Emergency call

The function makes it possible to establish a connection to the emergency services number “112”.

Note:

In order to trigger an emergency call, the mobile phone must be switched on, connected to the Traffic Pro and the reception must be adequate. Harman/ Becker cannot generally be held liable for the emergency call function.

X In the Telephone main menu, select

(PHUJHQF\FDOO.

5014

X Select <HV (start emergency call) or 1R

(do not start emergency call). If you select be triggered.

<HV, the emergency call will

*Only available for the Traffic Pro with Bluetooth® wireless technology. 93

Telephone mode*

5015

Following initiation of the emergency call, the following information is displayed in the status bar.

After the emergency call has been made, you can end the call as described in “Ending a call” on page 96.

Note:

A query as to whether you wish to start an emergency call will be shown, even if you dial the emergency services number “112” directly.

Settings

In the settings section you can activate/ deactivate the “Automatic call answering” and “Dialogue with call” functions.

X In the Telephone main menu, select

6HWWLQJ.

5016

X Turn the rotary control/push

button to select between

$XWRFDOODQVZHULQJ and 'LDORJXHIRUFDOOV.

X Turn the rotary control/push button

to switch the required function on

() or off ().

Automatic call answering

When the function ( ) is active, incoming calls will automatically be answered after approx. 5 seconds. You therefore do not have to answer the call.

Note:

When the function ( ) is active, the settings under Dialogue with call will be ignored.

Dialogue with call

If the function ( ) is active, a voice mode dialogue will automatically be activated to answer an incoming call.

Note:

The “Automatic call answering” function ( ) must be switched off so that the dialogue can start when the ( ) function has been activated.

94 *Only available for the Traffic Pro with Bluetooth® wireless technology.

Telephone mode*

5017

Telephone calls

Below, you can find information on the operating options available to you during an active telephone call.

Status display

The status display appears automatically during an active telephone call.

The status display shows the following information:

•Top left Telephone status display is active.

• A telephone symbol will be displayed in the centre left and, if available, the name of the caller/ the person you are calling. If the name is not available the number will be displayed. If the number has not been transmitted

8QNQRZQ will be displayed.

*60QHWZ, to indicate that the

• The name of the telephone currently connected will be displayed at the bottom left.

• The length of the call will be shown on the centre right of the display.

• The strength of the received telephone signal is displayed at the bottom right, if available.

Press to switch to the status display for radio mode or media mode. You can also switch to the navigation status display if route guidance is active.

Accepting/ rejecting a call

You can accept or reject incoming calls.

Accepting a call

The Traffic Pro announces an incoming call by means of a signal tone and the following display.

Note:

If the “Call waiting” function is active on the mobile phone the same signals are used to indicate that another call is waiting if a call is already taking place. If you accept the call the previous call will be ended without a query being made.

5018

X Select the $FFHSW entry and press the

rotary control/push button . The call will be accepted and the status display will be shown.

*Only available for the Traffic Pro with Bluetooth® wireless technology. 95

Telephone mode*

5019

Note:

Selecting

0XWH deactivates the signal

tone and the previously active source, radio or media, will be reactivated. However the call will be indicated until the caller ends the call.

Rejecting a call

You can reject an incoming call. The person calling will hear a busy signal.

X Select the 5HMHFW entry and press the

rotary control/push button . The call will be rejected. The status display of the previously active radio or media source will be shown.

Ending a call

Active calls can be terminated. For this purpose, status display must be first be accessed.

5017

X Press the rotary control/push button

The Options menu appears.

5020

X Select the +DQJXS entry. X Press the rotary control/push button

The call is terminated.

Options menu

The Options menu can be displayed during an active call. You can end the call, send DTMF tones or divert the call to the mobile phone.

X In the Telephone status display, press

the rotary control/push button .

5020

The Options menu appears.

X Turn the rotary control/push button

to select between

+DQJXS, '70) and 3ULYDWH.

96 *Only available for the Traffic Pro with Bluetooth® wireless technology.

Telephone mode*

5028

5021

End call

Select

+DQJ XS in the Options menu to

end the active call. See “Ending a call” on page 96.

DTMF

So-called DTMF dialling tones can be transmitted. For example, these tones are required to retrieve information from an answering machine.

X Open the Options menu.

X Select the '70) entry.

X Enter the required sequence of

numbers by turning and pressing the

rotary control/push button .

The entries must not be confirmed. The individual DTMF tones will be sent immediately after selection.

X Press to exit the input menu.

X In the input menu, select the

symbol.

Private

You can divert calls received via Traffic Pro to the mobile phone. The hands-free unit is then deactivated.

Notes:

• With some mobile phones, the connection from the mobile phone to the Traffic Pro will be interrupted when this function is activated. If this is the case you will have to reconnect the mobile phone to the Traffic Pro as described in “Connecting and disconnecting devices*” on page 117.

• If, at the end of the call, the function

3ULYDWH was activated, it will be

deactivated again for the next call.

X Open the Options menu. X Select the 3ULYDWH entry. X Press the rotary control/push button

to switch the function on ( ) or

off ( ).

*Only available for the Traffic Pro with Bluetooth® wireless technology. 97

Telephone mode*

Fast access telephone functions

In fast access mode the last 20 numbers or names which have been dialled, answered or rejected will be displayed in chronological order.

Notes:

The fast access entries have been given symbols (the symbols are displayed in following order – number not in memory, mobile phone number, business number, private number).

• The symbols , , and stand for answered calls.

• The symbols , , and stand for rejected calls.

• The symbols , , and stand for outgoing calls.

You may:

• Call numbers and names listed in fast access mode directly.

• Protect the fast access entries, i.e. the entry will not be deleted when the maximum number of entries is reached. The oldest unprotected entry will be deleted.

• Delete individual fast access entries.

• Delete the entire fast access list.

• Save an entry from the fast access list in the address book.

X Press .

5001

X The telephone fast access function

appears.

Direct calling

X Call up the telephone fast access

function.

X Turn the rotary control/push button

and then press the rotary control/ push button to select the required number or name from the list.

The call connection to the required person will be started immediately.

98 *Only available for the Traffic Pro with Bluetooth® wireless technology.

Telephone mode*

Protecting an entry

X Call up the telephone fast access

function.

X Select the entry to be protected. X Press the rotary control/push button

until a menu appears.

X Select the 3URWHFWHQWU\ entry. X Switch protection on ( ) or off ( )

by pressing the rotary control/push button .

Protected entries are identified by the

symbol.

Note:

A protected entry is only protected from being deleted in fast access mode. However, you can delete this protected entry individually, and it will also be deleted when the complete list is deleted.

Deleting an entry

X Call up the telephone fast access

function.

X Select the entry to be deleted. X Press the rotary control/push button

until a menu appears.

X Turn the rotary control/push button

and then press the rotary control/ push button to select the entry.

The entry is deleted from the fast access list.

'HOHWH HQWU\

Deleting a list

X Call up the telephone fast access

function.

X Press the rotary control/push button

until a menu appears.

X Turn the rotary control/push button

and then press the rotary control/

push button to select the

'HOHWH OLVW

entry.

5022

X When the prompt appears, select <HV

to delete the list or 1R to retain it. If you select in the fast access function.

<HV the list will be deleted

*Only available for the Traffic Pro with Bluetooth® wireless technology. 99

Telephone mode*

5023

Saving a number in the address book

X Call up the telephone fast access

function.

X Select the entry to be saved. X Press the rotary control/push button

until a menu appears.

X Turn the rotary control/push button

and then press the rotary control/

push button to select the

ERRN

entry.

6DYHLQDGGUHVV

&UHDWHQHZHQWU\

• Select this option to create a new entry in the address book.

•

$PHQGHQWU\

Select this option to add the current number to an existing entry in the address book.

Creating a new entry

X Select the &UHDWHQHZHQWU\ entry.

2030

X Turn the rotary control/push button

and then press the rotary control/ push button to select each letter in the surname one after the other.

Note:

Please also refer to the description in “Data entry menus” on page 13.

X Select the symbol from the

input menu.

X press the rotary control/push button

and hold for at least 2 seconds.

The entry is adopted.

2031

X Turn the rotary control/push button

to select between

&UHDWHQHZHQWU\ and $PHQGHQWU\.

X Confirm your selection by pressing

the rotary control/push button .

5024

X Turn the rotary control/push button

to select between

0RELOHWHO, %XVLQHVVWHO and 3ULYDWHWHO.

X Confirm your selection by pressing

the rotary control/push button .

100 *Only available for the Traffic Pro with Bluetooth® wireless technology.

Becker TRAFFIC PRO 7945 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Safety instructions

Information regarding general road safety

Overview of controls Traffic Pro

Overview of controls Traffic Pro with Bluetooth®

General operation

Menu basics

Fast access function

Main menu

Status display

Options menu

How to use the menus

Data entry menus

Anti-theft device

Entering unit code numbers

What to do if an incorrect code number has been entered

Removing/Inserting the control panel

Removal

Insertion

Inserting/Removing the cover

Inserting the cover

Removing the cover

Switching the unit on/off

Switching on

Switching off

Setting the volume

Sound settings

Calling up the sound settings

Setting the equalizer

Defining the equalizer setting

Setting balance and fader

Balance setting

Fader setting

Switching loudness on/off

Becker Surround

Subwoofer

Crossover

Reset settings

Mute

Navigation mode

What is navigation?

Navigation CDs

Selecting navigation

Entering a destination

Selecting a country

Entering a destination town

Entering the destination road

Setting the route options

Saving/Deleting route options

Saving a destination

Navigation fast access

Navigating from fast access

Protecting an entry

Deleting an entry

Deleting a list

Creating a new entry

Adding data to entries

Point of interest

Local

In country

Local area of destination

In place

Information about points of interest

During route guidance

Navigation status screen

Example navigation displays

Options menu

Cancelling route guidance

Traffic announcements

Route list

Stopover

Blocking a route

Modifying route options

Switching navigation announcements on/off

Displaying/Storing position

Displaying traffic announcements

Displaying/Changing route settings