Light Package 2
Light Package 2
Multipoint Laser G-50mW R-80mW
LED Moon Flower sound controlled
Ref. Nr. 153.780
Instruction Manual
Gebruiksaanwijzing
Mode d’Emploi
Gebrauchsanleitung
—2—
Multipoint Laser G-50mW R-80mW
User’s manual
Thanks for your purchasing, please read this manual carefully before operating the system. It gives you general information
for your safe and better operation.
Installation
Firstly, be sure that the using voltage is match with the
voltage marked on the base of the laser;
Installation should be made by professional technician.
fix the laser lighting and adjust the angle of the moving
head to you need;
Be sure that there is no flammable or explosive subject
nearby. The least distance is 0.5 meters. at the same
time, keep more than 15cm between the wall and laser
lighting;
Please check whether the fan and the exhaust is blocked;
There is a hole for connection. when hang the laser lighting,
be sure the cable can undertake 10 times of the lighting
weight;
The laser lighting should be fixed;
It is essential to be earthed well for the sake of safety.
WARNING DATA
Lasers can be hazardous and have unique safety
considerations. Permanent eye injury and blindness
is possible if lasers are used incorrectly. Pay close
attention to each safety REMARK and WARNING
statement in the user manual. Read all instructions
carefully BEFORE operating this device.
Indicates a skill or other useful information for
special situations.
Indicates important information to protect
personnel from laser incident or injury.
Prevent damage or injury from incorrect operation.
Laser safety warming labels.
To protect the environment, recycle packing
material wherever possible.
The projector is for indoor use only, IP20. Use
only in dry locations. Keep this device away
from rain and moisture, excessive heat,
humidity and dust. Do not allow contact with
water or other fluids.
Don’t throw this product away just as general trash,
please dispose of this product following the abandon
electronic product regulations in your area.
The projector must be installed in a location with adequate
ventilation, at least 50cm (20 inches) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
Avoid direct eye contact with laser light. Never
intentionally expose your eyes or others to direct laser
light..
This laser product can potentially cause instant eye
injury or blindness if laser light directly strikes the eyes.
It is illegal and dangerous to shine this laser into
audience areas, where the audience or other personnel
could get direct laser beams or bright reflections into
their eyes.
It is an offense to shine any laser at aircraft.
There are no user serviceable parts inside the unit. Do
not open the housing or attempt any repairs yourself. In
the unlikely event your unit may require service, please
contact the dealer nearest to you..
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
NON-INTERLOCKED HOUSING WARNING
This unit contains high power laser devices internally. Do not open the laser housing, due to potential exposure to unsafe
levels of laser radiation. The laser power levels accessible if the unit is opened can cause instant blindness, skin burns and
fires.
—3—
LASER SAFETY AND OPERATING INSTRUCTIONS
STOP AND READ ALL LASER SAFETY DATA
Laser Light is different from any other light source with which you may be familiar. The light from this product can potentially
cause eye injury if not set up and used properly. Laser light is thousands of times more concentrated than light from any other
kind of light source. This concentration of light power can cause instant eye injuries, primarily by burning the retina (the light
sensitive portion at the back of the eye). Even if you cannot feel “heat” from a laser beam, it can still potentially injure or blind
you or your audience. Even very small amounts of laser light are potentially hazardous even at long distances. Laser eye
injuries can happen quicker than you can blink. It is incorrect to think that because these laser entertainment products split
the laser into hundreds of beams or laser beam is scanned out in high speed, that an individual laser beam is safe for eye
exposure. This laser product uses dozens of mini Watts of laser power (Class 3B levels internally). Many of the individual
beams are potentially hazardous to the eyes. It is also incorrect to assume that because the laser light is moving, it is safe.
This is not true. Nor, do the laser beams always move. Since eye injuries can occur instantly, it is critical to prevent the
possibility of any direct eye exposure. In the laser safety regulation, it is not legal to aim Class 3B lasers in areas which
people can get exposed. This is true even if it is aimed below people’s faces, such as on a dance floor.
Do not operate laser without first reading and
understanding all safety and technical data in this
manual
Always set up and install all laser effects so that all
laser light is at least 3 meters (9.8 feet) above the
floor on which people can stand. See “Proper Laser
Set-up & Usage” section later in this manual
After set up, and prior to public use test laser to ensure
proper function. Do not use if any defect is detected. Do
not use if laser emits only one or two laser beams rather
than dozens/hundreds, as this could indicate damage
to the diffraction grating optic, and could allow emission
of higher laser levels.
Do not point lasers at people or animals
Never look into the laser aperture or laser beams
Do not point lasers in areas in which people can
potentially get exposed, such as uncontrolled balconies,
etc.
Do not point lasers at highly reflective surfaces such as
windows, mirrors and shiny metal. Even laser
reflections can be hazardous.
Never point a laser at aircraft, this is a federal offense
Never point un-terminated laser beams into the sky
Do not expose the output optic (aperture) to cleaning
chemicals
Do not use laser if the laser appears to be emitting only
one or two beams
Do not use laser if housing is damaged or open, or if
optics appear damaged in any way.
Never open the laser housing. The high laser power
levels inside of the protective housing can start fires,
burn skin and will cause instant eye injury.
Never leave this device running unattended.
The operation of a class 3B laser show laser is only
allowed if the show is controlled by a skilled and
well-trained operator familiar with the data included in
this manual.
The legal requirements for using laser entertainment
products vary from country to country. The user is
responsible for the legal requirements at the
location/country of use.
Always use appropriate lighting safety cables when
hanging lights and effects overhead
Power off before installation or maintenance
The danger class of this laser lighting is CLASS IIIB.
It’s dangerous for observing laser. The safe minimum
distance is 13cm,the safe maximum time is 10 seconds
Keep at least 0.5 meters distance between the lighting
and flammable material
LASER SAFETY LABEL REPRODUCTIONS
Caution – Class 3B LASER RADIATION, WHEN OPEN, AVOID EXPOSURE TO BEAM
LASER RADIOATION AVOID EXPOSURE TO BEAM CLASS 3B LASER PRODUCT.
The label indicates the laser beam output aperture.
LASER EXPOSURE WARNING
—4—
LASER LIGHT AVOID DIRECT EYE EXPOSURE
Further guidelines and safety programs for safe use of lasers can be found in the ANSI Z136.1 Standard “For Safe Use of
Lasers”, available from “www.laserinstitute.org”. Many local governments, corporations, agencies, military and others, require
all lasers to be used under the guidelines of ANSI Z136.1. Laser Display guidance can be obtained via the International Laser
Display Association, www.laserist.org.
Notices
Non-professional do not dismantle or repair the laser lighting. when there is a problem, please inquire with the professional
or contact with the local dealer;
Do not exposure in the wet or dirty condition;
Prevent the laser lighting from strong vibration or punch;
Prevent other subject enter into the lighting;
Ensure the fan is not blocked;
Before power on, be sure electric outlet is connected well with the socket;
Do not turn on and turn off frequently , avoid to turn on the power for a long time;
Please power off the lighting for 15 minutes after running two hours, ensure that the laser system is in well cooling state;
Do not looking at the laser source using telescope
Do not touch the laser lighting by wet hand and forcefully pull the power line;
The distance between lighting and casting medium should be more than 1 meters;
Do not dismantle the lighting;
Please directly contact with the local dealer when the trouble occurred;
When to be transported, use the original package to avoid shocking;
Maintenance
Please clean the lens regularly. Do not do it using the wet cloth or other chemical. the clean times is depend on the using
frequency and surrounding condition; it is recommended that should be cleaned every 20 days;
Please clean the lighting surface and engine outlet regularly.
Statement
All the user should abide by the above waning items and operation instructions, otherwise any trouble due to incorrect
operation is out of warranty.
—5—
INSTALLATION
This fixture has been designed to be hung. It is recommended for safety purposes, your lighting effect are properly mounted
using a suitable hanging clamp and safety cable. Items appropriate for safe and effective mounting are easily sourced from
your lighting vendor.
International laser safety regulations require that lasers must be operated in the fashion illustrated below, with a minimum of 3
meters of vertical separation between the floor and the lowest laser light vertically. Additionally, 2.5 meters of horizontal
separation is required between laser light and audience or other public spaces.
PANEL DESCRIPTION
1. LASER APERTURE
2. POWER INPUT: 5VDC power input is used to connect the AC/DC adaptor.
3. MICROPHONE
4. MOTOR SPEED CONTROL: Regulating the speed of the motor
5. MODE SWITCH: FUNCTION SWITCH: 2= Strobo flash (adjust), 1=ON, 4=OFF, 3=Voice controller
FAN on top of the laser: Used to cool the components inside the enclosure. Never cover this fan outlet!
HANGING BRACKET: 2 screws on both sides to fasten the unit and a mounting hole to fix on a stand or wall.
—6—
OPERATION
Lasers are not designed for continual use. Regular breaks during operation are essential to maximize the life of this device.
Do not switch the unit off and on again in a short time, let the laser cool down before switching the laser on.
Important: Never look directly into the laser beam!
Remove the unit from the mains when not in use.
TECHNICAL PARAMETER
Rating Voltage: .............................. 5VDC / 1500mA
AC Power supply ........ 100V~240VAC / 60Hz-50Hz
Laser source· ........................ 50mW green 532nM
.................................................... 80mW red 650nM
Dimensions .................................. 122 x 92 x 52mm
Weight ........................................................... 0.48kg
—7—
Multipoint Laser G-50mW R-80mW
Hartelijk dank voor de aanschaf van deze Laser.
Deze handleiding bevat belangrijke laser veiligheids informatie. Lees deze handleiding eerst door alvorens de laser
te gebruiken om oogletsel te voorkomen en om de wet niet te overtreden. Bewaar deze handleiding als naslagwerk.
WAARSCHUWING
Lasers kunnen zeer gevaarlijk zijn en daarom moeten alle veiligheidsvoorschriften in acht worden genomen.
Als lasers onjuist worden gebruikt kan oogletsel en zelfs blindheid optreden. Lees daarom alle veiligheids
voorschriften en opmerkingen goed door in deze handleiding.
Attentie! Geeft een vaardigheid weer of andere belangrijke informatie voor speciale situaties.
Belangrijk! Geeft belangrijke informatie weer i.v.m. persoonsbescherming m.b.t een laserongeluk of letsel.
Voorzichtig! Gebod om, beschadiging te voorkomen of, letsel i.v.m. onjuiste bediening te voorkomen
Laser! Laser veiligheid waarschuwingslabel.
Recycle Milieubescherming, recycle verpakkingsmateriaal daar waar mogelijk.
In huis De laser mag alleen binnenshuis gebruikt worden, (IP20). Alleen in droge- en nooit in vochtige
ruimten gebruiken, mijd extreme hittebronnen en stof. Laat de laser nooit in contact komen met
water of andere (chemische) vloeistoffen, reinigingsmiddelen enz.
WEEE Gooi een defecte laser nooit bij het huisafval, maar lever deze in bij een inzamelingsplaats of een `
gemeentelijk depot. Een groot deel kan gerecycled worden.
Afstand De laser moet in een goedgeventileerde ruimte gebruikt worden, en minstens 50cm van andere
apparatuur of oppervlakken verwijderd zijn. Controleer altijd of ventilatiegaten open, en niet
geblokkeerd zijn.
LASER VEILIGHEIDSVOORSCHRIFTEN
Vermijd direct oogcontact met, en stel uw lichaam nooit bloot aan de laserstraal. KIJK NOOIT IN DE
LASERSTRAAL!
De laserstraal kan oogletsel of blindheid veroorzaken.
Het is verboden en gevaarlijk de laserstraal in het publiek te schijnen, of daar te schijnen waar reflecties het
publiek bereiken.
Het is verboden de laserstraal op vliegtuigen te richten.
In de laserunit bevinden zich voor u geen onderdelen die door u gebruikt kunnen worden. Open daarom nooit de
behuizing en probeer de unit nooit te repareren. Laat dit over aan gekwalificeerde vakmensen of stuur de unit
naar uw dealer.
Het afstellen of gebruik anders dan omschreven in deze handleiding kan leiden tot een gevaarlijke blootstelling
aan ongewenste straling.
Het is mogelijk letsel op te lopen bij gebruik van de laser. Lees deze
instructies goed door. Het geeft informatie over de installatie, veilig
gebruik en service!
Loading...