Bauknecht GSI 50002 SL Quick Reference Guide

PROGRAM SELECTION BUTTON Push “Programs” button (repeatedly) until the indicator of the required program lights up (see “Table of programs” below).
CANCEL/OFF BUTTON Push this button to switch off the control panel. If pressed when a program is running it cancels the program ongoing draining water for 1 minute. If pressed when the dishwasher is switched off it drains any possible liquids from dishwasher (1 minute process). If the indicator flashes repeatedly, see page 6 ­chapter “What to do if...”.
START/RESUME BUTTON Push this button to star t th e sel ected prog ram: t he indicator lights up and goes off at the end of the program. When the door is opened during a washing cycle, the cycle is temporarily paused: the Start indicator blinks. To resume the cycle close the door and push Start button again.
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label i n co mpli anc e w it h EN 502 42 r egul ati ons. - Not e fo r Testing Institutes: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
Table of programs
Deter-
gent
Consumption
Drying
Phase
P
Programs Loading instructions
Litres kWh
Minutes
1)
1
Rapid 40°C
Lightly soiled crockery, with no dried-on food.
X 13.0 0.70 30 NO
2
Eco
2)
50°C
Normally soiled crockery. Energy-saving program.
X 15.0 1.15 165 Full
3
Daily 60°C
Normally to heavily soiled crockery.
X 16.0 1.35 120 Full
4
Intensive 65°C
Recommended program for heavily soiled crockery, especially suitable for pans and saucepans.
X 15.0 1.50 140 Full
5
Halfload 50°C
Ideal for washing a half load of lightly or normally soiled crockery
X 13.0 1.00 130 Full
5019 496 01734
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS
QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTR UCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY
BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
Quick reference guide
Chart
GB -1-
5
7
86
1
4
10
9
2
3
1- salt reservoir 2- rinse aid dispenser 3- detergent dispenser 4- racks system 5,6,7,8- available functions on the panel 9- filters 10- spray arms
1. Ask your water supply company what the water hardness is... 2. ...enter this value on
your dishwasher
Suggestions for detergent use
German
degrees °dH
French
degrees °fH
English
degrees °eH
Water hardness
level
3 first PROGRAM LEDs
lit on the panel
(see table of programs)
P1 P2 P3
Gel or Powder
(rinse aid and
salt)
Tablets
0 - 5 0 - 9 0 - 6.3 Soft 1
go to step 1
(see “Daily
check”)
6 - 10 10 - 18 7 - 12.6 Medium 2 11 - 15 19 - 27 13.3 - 18.9 Average 3 16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4
if water is
HARD extra salt
needs to be
added
(go to step1,
“Daily check”)
22 - 28 38 - 50 26.6 - 35 Hard 5 29 - 35 51 - 63 35.7 - 44.1 Very hard 6 36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7
Water hardness should be set only
before the first wash or if water
hardness has been changed
1
Visual indicator (depending on the model). Unscrew cap.
Fill the salt reservoir with water
before the first wash only.
(depending on the model)
The salt level indicator lamp may rem ai n lit at the end of several wash cycles. If the water hardness level falls with in category (soft), no salt is required.
Salt indicator on the control pa ne l Salt indicator on the salt reservoir cap
The indicator lamp lights up when SALT NEEDS TO BE ADDED.
green: OK.
clear: NEEDS TO
BE ADDED
Daily check
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)
- Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds.
- Programs LEDs will indicate the water hardness setting.
- Press the Programs button to increase setting (when the level reaches 7, the next key press will set the leve l back to 1.
- Wait 30 seconds (control panel switches off) or press START/Resume button to save setting.
Add salt (never add detergent!)
min. 0.8 kg / max. 1 kg
Water hardness level is factory set for medium-hard water (level 4).
Even if you use tablets which include salt functionality, you must still add regeneration salt since such detergents are not effective enough at softening hard water.
At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).
Screw on the cap. Salt residual around the cap need to be removed. Some salt reservoir have a level indicator integrated in the cap (see below how to check).
Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient). Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components. The guarantee is not applicable if faults are caused by such circumstances.
How to set water hardness in order to always assure the best cleaning results
First time use
GB -2-
3
Check the rinse aid indicator to check the level into the dispenser.
(depending on the model) Rinse aid indicator on the control panel Rinse aid indicator on the dispenser
The indicator lamp lights up when RINS E AID NEEDS TO BE ADDED.
dark: OK. clear: NEEDS TO BE ADDED
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.
If there are streaks: reduce the dosage by turning t he dial to a lower setti ng (1-3). If crockery is not perfectly dry: increase th e dosage by turning the dial to a higher setting (5- 6). Plastic di shes have more diff iculty drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.
Daily use
Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Open the cover A
(press the dedicated button).
Only fill the detergent dispenser prior to starting a wash program.
Shut the cover
by pressing dedicated ribs.
Insert detergent: Tablet / powder / liquid into the big chamber
Use only one tablet per one cycle, only placed in detergent dispenser.
All types of tablets can be used, but for 2 in 1 type adding of salt is mandatory. Some type of tablets could not dissolve completely during the short programs (Rapid, Fragile, H an dwash); placing the tablet on the tub bottom can help dissolving and washing.
If required, open the cover B (press the dedicated button).
Add rinse aid to the max. line ~150 ml
The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button to open the cover B. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.
Visual indicator
2
Please look for the recommendation of the detergent manufacturer on the packaging of the detergent product.
UPPER RACK - depending on the model
Daily check
GB -3-
Loading...
+ 5 hidden pages