Page 1
4gb90296.fm5 Page 1 Thursday, May 16, 2002 10:41 AM
Before using the dishwasher, read the user instructions!
GSI 4988
Quick Reference Guide
Wash cycle
GB
Programme selector knob
Pre-Rinse Washing Drying
Options
Start button
Switches “on” when the
dishwasher is operating. Flashes
when a fault occurs. Switches off
at the end of the programme.
Indicators
Add rinse aid
Add regeneration salt
Only add regeneration salt
immediately before starting a
wash programme.
Programme chart
Programmes Loading instructions A B
Automatic programme recommended for
Eco Normal 40-55°C
Intensive 60-70°C
routine washes, with no dried-on or burnt
food (not for EN 50242).
Automatic programme recommended for
heavily soiled crockery with dried-on or burnt
food, for example pans and saucepans.
Time and failure display
Indicates in hours the time remaining until the
start of the wash cycle. Toward the end of the
programme, during the drying cycle, the display
will indicate the time remaining in minutes.
“F...” Information for the After-Sales Service
“Delayed start” button
The wash cycle can be programmed to start after 1 24 hours. With each successive touch of the button,
the delayed start indicator increases by 1 hour, and
after 24 returns to 00. Then press the Start button.
The dishwasher will start at the set time.
“Half load” button
This function can be used with any programme.
The indicator lamp switches on. The wash cycle is
activated for the upper
Programme
end
3)
or
lower rack
Detergent
X X 10-13 0.8-1.05 50-110
X X 13-20 1.1-2.0 90-140
2)
Litres kWh Minute s
only
.
Consumption
3)
Pre-Rinse cold
Glass 40°C
Rapid 30 min 40°C
Eco
1) Reference programme for energy label in
compliance with EN 50242 regulations;
2) Refer to “User instructions“;
Important information for Test Laboratories:
For detailed information on the EN comparison test and other tests, contact the following address:
“nk_customer@email.whirlpool.com”.
Black Process Plate
Crockery to be washed later. - - 4.0 0.03 14
Light soiling, for example glasses
and cups.
Lightly soiled crockery with no
dried-on food.
1)
Normally or heavily soiled crockery. X X 13.0 1.05 120
50°C
3) Program data obtained in conformity with
European standard EN 50242. Values may vary in
relation to usage, e.g.: different loads, water
temperatures - above or below 15°C - as well as
water hardness and power supply voltage, etc.
(We reserve the right to make technical modifications)
X - 10.0 0.80 55
X - 10.0 0.65 30
5019 496 90296
Page 2
4gb90296.fm5 Page 2 Thursday, May 16, 2002 10:41 AM
How to use the appliance
Further indications are given in the single chapters and in the user instructions.
Switch on the appliance
How to fill the
detergent dispenser
Automatic start by turning the programme selector knob (in
case of retractable knob, first press the knob to access it).
Large compartment A:
With each wash cycle.
Small compartment B:
For programmes with pre-wash only.
BA
C
Check the
rinse aid level
Check the regeneration
salt level
Load the racks
Close the door,
turn on the water tap
Select a programme
Select additional
options
Press the START button
Wash cycle
Switch off the appliance
Mechanical indicator C.
Electric indicator on control panel (if provided).
On models with water softener system only.
Mechanical indicator D.
Electric indicator on control panel (if provided).
Refer to the dishwasher loading instructions.
Select the desired programme.
The corresponding indicator lamp comes on.
If necessary (and if provided) the corresponding indicator
lamp lights up.
The selected programme
is then memorised (even
in the event of power
failure).
Only after the START button has switched off: access the knob
(in case of retractable knob, press and then release the knob).
“Change programme”
Press the START button for 2 sec. until
the Start indicator lamp switches off;
Select another programme and press
the START button again.
- Only open the dishwasher if necessary
(Warning: beware of hot steam).
- If the appliance is switched off during
a wash cycle, when switched on
again it will resume the cycle from
where it was interrupted.
Shut off the water tap,
unload the racks
Black Process Plate
Warning: when the door is opened steam comes out!
Unload the appliance, starting from the lower rack.
Page 3
4gb90296.fm5 Page 3 Thursday, May 16, 2002 10:41 AM
Dishwasher loading instructions and racks provided
Upper rack:
Multi-purpose support (A) 1):
Depending on the position, for
long-handles utensils, cups and
glasses. May be used in three
different positions.
Crockery holders (B):
Depending on the position,
for example plates, cups and
long-stemmed glasses.
Revolving glass support (C)
Depending on the position, for
example small or longstemmed glasses.
Half Load:
Load the upper rack only.
Place the cutlery basket (D) in
the upper rack.
Rack height adjustment
(also when loaded):
• Lower adjustment: pull
out the two rack handles
outwards (E) and lower the
rack.
• Upper adjustment: pull the
two handles (E) upwards until
the rack clicks into place
(Factory setting).
The rack must be level on
both sides.
depending on the model
2)
:
Lower rack:
Depending on the model with
fixed or tilting plate holders (F).
Half Load:
Load the lower rack only.
Greater washing power,
particularly for plates and
saucepans.
Cutlery basket (G) or (H):
Some models are provided
with a grid (I) that can be
fitted onto the cutlery basket
to keep items separated.
Cutlery basket (D) for
appliances with half load only.
Sharp knives and forks that
might cause injury must be
placed in the cutlery basket with
the handles positioned upwards.
Only use dishwasher-proof crockery and dishes. Do not use the appliance for it ems not sui table f or w ashing in
a dishwasher, for example wooden items, aluminium, plastic utensils, tin, hand-decorated crockery (unglazed),
silver cutlery.
Spare parts which are sold separately:
1)
Multi-purpose support (A) - N. AMH 369.
2)
Revolving glass support (C) - N. WGH 1000.
Black Process Plate
Page 4
4gb90296.fm5 Page 4 Thursday, May 16, 2002 10:41 AM
What to do if...
If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the
problem (* see also the corresponding chapter in the user instructions).
Problem Cause Remedy
The appliance is not
working
If crockery is not
perfectly dry
If crockery is not
perfectly clean
Sandy or grainy
residues
Colour of plastic
parts faded
• No water supply. • Open the tap.
• The appliance does not load
sufficient water.
• There is a power failure. • Insert the plug into the mains socket.
• Starting the selected programme. • The programme can be set to “0” to start.
• Insufficient r inse aid. • Increase dosage *.
• Residual water in cavities. • Load crockery at an angle.
• The water jet does not reach the
crockery.
• Insufficient detergent. • Follow recommended detergent dosage.
• Unsuitable programme. • Select a more intense wash cycle.
• Spray arms blocked. • The spray arms must be able to turn freely.
• Spray arm nozzles clogged. • Remove any impurities obstructing the water
• Incorrect detergent/detergent too
old.
• Clogged filters. • Check filters regularly/if necessary clean *.
• Filters incorrectly assembled. • Insert the filter correctly *.
• Tomato/carrot juice... • Depending on the material, if necessary use a
• Clean the water supply tap filter.
Ensure there are no kinks in the water hose.
• Press the Start button.
• Close the door.
• Check the domestic circuit fuse.
• Arrange crockery so that items do not touch
each other. Load crockery upside do wn.
flow *.
• Use a good quality deterg ent.
detergent with a greater whitening power.
Deposits on crockery
• removable • Streaks on the crockery/glasses. • Increase the rinse aid dosage *.
•not removable • Insufficient water softening,
Opaque glasses/
glasses not sparkling
Rust on cutlery
Identifying appliance
faults
If after carrying out the above checks the malfunction persists or appears again, turn the appliance off
and turn off the water supply tap, then call our After-Sales Service (see guarantee).
Before contacting our After-Sales Service, take note of the following:
• The nature of the fault.
• The appliance type and mode l.
• The service code (the number indicated on the adhesive ratin g
plate) inside the door on the right-hand side.
Black Process Plate
• Streaks on glasses. • Reduce the rinse aid dosage *.
• Layer of salt on crockery/glasses. • Close the salt container lid properly*.
calcium deposits.
• Cannot be washed in the
dishwasher.
• Not made of stainless steel. • Use suitable cutlery.
• The START ind icator lamp flashes. • Ensure that the filter ass embly is not clogged
• Indicator F... (if provided). • Call the After-Sales Service.
• Change water hardness setting, if necessary
add salt *.
• Use suitable glasses.
and if necessary clean it *.
Start the programme again. Press the START
button for about 2 seconds, until the START
indicator lamp switches off. Select a new
programme and press the Start button again.
Loading...