Bauknecht GSI 4853/3 TW-WS, GSI 4853/3 TW-IN, GSI 4853/3 TW-SW, GSI 4853/3 TW-BR Quick Reference Guide

GB

GSI 4853

Further indications are given in the pages to follow and in the user instructions.

Water supply indicator

Check the appliance fills with water.

“Water stop” device indicator

“Water stop” device not working.
Switch off the dishwasher and shut off the water tap.

Rinse aid level indicator

Add rinse aid.

Salt level indicator

Add regeneration salt; only add regeneration salt
immediately before starting a wash programme.

Quick Reference Guide

Programme progress indicator

Pre-rinse /
Pre-wash

Washing

Options

Eco-Dry

The indicator lamp switches on during dry
cycles without fans.

Drying
Programme end

Delayed start button

The wash cycle can be programmed to start after
3-6-9 hours.

Then press the Start button.
The dishwasher will start at the set time.

Start button

Indicator lamp lit while the dishwasher is operating.
Flashes when a fault occurs.
Switches off at the end of the programme.

On / Off Button

Programme Symbol

and Temperature

Pre-wash

Rapid 40° C

Bio-Normal 50° C

Normal 65° C

Intensive 70° C

1) Values may vary in relation to usage, e.g.: different loads, water
temperatures - above or below 15° C - as well as water hardness and power supply voltage, etc.

2) Programme recommended when using detergents of type B (enzyme-based detergents).
Reference programme for energy label.

3) Programme recommended when using detergents of type A (non enzyme-based detergents).

3)

Crockery to be washed later.

Lightly soiled crockery with no dried-on food.

2)

Normally or heavily soiled crockery with dried-on food.

Normally or heavily soiled crockery with dried-on food.

Heavily soiled pans and saucepans.

Programme selection and

recommended load type

Place the detergent in the:

small large

compartment compartment

- - 5.0 0.02 9

- X 13.0 0.85 30

X X 16.0 1.22 91

X X 16.0 1.55 86

X X 21.0 1.68 93

Water

(Litres)

Consumption

Normal load

Energy

(kWh)

5019 100 90298

(We reserve the right to make technical modifications)

1)

Time

(Min.)

B

A

C

How to use the dishwasher

1. After loading the dishwasher, close the
door properly and open the water
supply tap.

2. Press the On/Off button to switch the
dishwasher on.

indicator lamps will switch on.

3. Select the desired programme by
pressing the corresponding button.

The corresponding indicator lamp
lights up.

(if supplied).

4. Press the Start button to start the
selected wash programme.

indicator lamp will light up.

the programmed data cannot be
altered by pressing the programme
selector buttons.

once the Start button has been

Note:

pressed, the dishwasher memorises the
last programme selected. This
information remains in the memory even
during interruption of the power supply.

To change the selected
programme, press the Start button
for about 5 seconds

indicator lamp switches off.

Select a new programme using the
programme selector knob and
press the Start button.

if the dishwasher is switched off

Note:

during a wash programme, when
switched on again it will resume the
wash cycle from where it was
interrupted.

Only open the dishwasher door if
strictly necessary during a wash
cycle and exercise maximum
caution. Danger of scalding from
steam.

5. To indicate the end of the programme,
the Start indicator lamp switches off
and

the End indicator lamp (if fitted)

lights up

One of the programme

If required, select options

The Start

Once set,

, until the Start

(for about 30 min.)

.

6. Once the Start indicator lamp has
switched off press the On/Off button to
switch the dishwasher off.

indicator lamps switch off.

7. Open the door (warning: beware of hot
steam). Unload the lower rack before
the upper one. Close the water tap.

All the

Upper rack

Rack height adjustment:

(The dishwasher is delivered with the
upper rack in the top position).
The rack height can also be changed
when loaded.

• To lower: pull out the
handles and gently lower the rack.

• To raise: pull up the
until the rack clicks into place.

side

two

side handles

two

Upper and lower rack

• The rack must be level on both
sides.

Crockery holders:

• Down: cups and long-stemmed glasses.

•

Up: plates.

“Vario Organizer” multi-purpose
support:

• To be used, for example, for long­handled utensils

with the blade facing downwards),

cups and glasses.

• May be used in three different
positions (see also “Dishwasher
loading instructions” on Page 4).

1. Upon the left-hand side of the rack.

2. Upside-down, towards the centre of
the rack.

3. Upside-down, towards the left side.

Glass holder:

(arrange knives

Lower rack

B

A

Plate holders:

• May be lowered to increase
available space (A).

• May be removed to increase
available space (B). To remove:
pull the handle up.

Cutlery basket:

The cutlery basket can be removed to
increase (C) available space.

C

Please read the user instructions carefully.

• Arrange crockery so that items do not
touch each other. Arrange large
crockery in the lower rack and smaller
crockery in the upper rack.

• Load cups at an angle to facilitate
water drainage.

• Generally speaking, place cutlery in the
basket with the handles positioned
downwards, but ensure that any sharp
knives and forks that might cause
injury are placed in the basket with the
handles positioned upwards.

• Make sure the water jet can reach all
loaded items and that the spray arms
turn freely.

Important

• Fill the detergent dispenser and check
the salt and rinse aid level.

• Do not use the appliance for items not
suitable for washing in a dishwasher,
for example: wooden items, aluminium,
plastic utensils, tin, hand-decorated
crockery (unglazed), silver cutlery.

• Do not put liquid fat in the dishwasher
(e.g. oil used for frying) or candle wax.

• If a fault occurs or you wish to change
the current programme press the
“START” button (for about 5 seconds)
until the corresponding indicator lamp
switches off.

• If regeneration salt is to be added,

Tips and advice

immediately

in order to eliminate any residual salt
(rinsing alone is not sufficient).

• Sometimes even though the
regeneration salt container has been
filled, the corresponding indicator lamp
(if fitted) will light up during the first
wash cycle after filling with salt.

start a wash programme

• Before starting a wash programme,
make sure that the spray arms can turn
freely and are not impeded by crockery
or cutlery.

• Only switch off the dishwasher once
the “Start” indicator lamp has switched
off. If the dishwasher is switched off
during a wash cycle, when switched on
again it will resume the cycle from
where it was interrupted without having
to start it again.

If a fault occurs, before contacting our
After-Sales Service, make the following
checks to try and remedy the problem:
The dishwasher is not working:

• Is the plug properly inserted in the wall

socket?

• Is there a power failure?

• Is the dishwasher switched on?

• Has the Start button been pressed?

• Has the delayed start timer been set

(if fitted)?

• Is the water supply tap on?

• Is the flow of water obstructed by

impurities? If so, close the water supply
tap, detach the water hose and clean the
filter. Then re-connect the water hose to
the tap and open the water tap once
again.

• Are the filters clogged? (See “Care and

maintenance” chapter in the user
instructions).

• Is the door closed properly?

• Is a fault indicated?

(The Start indicator lamp flashes).
Start the programme again from the
beginning: press the Start button for
about 5 seconds, until the Start indicator
lamp switches off.
Select a new programme and press the
Start button.

Troubleshooting Guide

Crockery still dirty after washing:

• Was the crockery loaded properly?

• Crockery must be loaded facing

downwards; this is important, especially
for large items of crockery.

• The water jets must spray the entire
surface of all items.

• Make sure that crockery and cutlery are
arranged properly.

• Have you selected the correct programme?

• Did you use too much or too little detergent?

(The use of poor quality detergents may
result in less effective washing).

• Are the filters clogged or incorrectly
assembled? (See “Care and Maintenance”
chapter in the user instructions).

• Are the spray arms blocked or the nozzles
clogged? (See “Care and Maintenance”
chapter in the user instructions).

• Is the lower spray arm correctly fitted?

• Is the salt container cap (water softening

system) screwed down?

Marked crockery:

• Is the water hardness level selector not
properly adjusted? (See “Filling the salt
container” in the user instructions).

• Is the salt container empty? (See “Filling the
salt container” in the user instructions).

• Was insufficient detergent used? (See
“Filling the detergent dispenser” in the

user instructions).

Marked glasses and cutlery:

• Was too much rinse aid used? (See
“Filling the rinse aid dispenser” in the user

instructions).

Note:

with some models, when the Start
button is pressed a pre-wash cycle precedes
the actual wash programme; this
regenerates the water softening system.

AFTER-SALES

SERVICE

If after carrying out the above checks
the malfunction persists or appears
again, turn the appliance off and turn
off the water supply tap, then call our
After-Sales Service (see guarantee).
Please specify:

• The nature of the fault.

• The appliance type and model.

• The service code (the number after

the word Service on the adhesive
rating plate) inside the door on
the right-hand side.

Your full address and telephone

•

number.

Please read the user instructions carefully.

Dishwasher loading instructions

UPPER RACK

LOWER RACK

Depending on the model, rack features may vary (see “Upper and lower rack” description).