Page 1
MINI-SCREEN Controller Models
MSDINT-1 and MSDINT-1L2
Supplement to MINI-SCREEN Instruction Manual 44895
Printed in USA 04/00 P/N 62875
Figure 20. MINI-SCREEN System electrical connections.
Figure 17. Control Module Dimensions and Mounting Hole Locations.
The enclosed MINI-SCREEN controller
MSDINT-1, MSDINT-1L2, or replacement
board reflect the new MINI-SCREEN DIN
controller design. These controllers are
identical to the old MINI-SCREEN DIN
controller, except that they have
removeable wiring blocks. With the
removeable wiring blocks, wiring terminal
numbers change and one overall
controller dimension increases. This
supplement modifies the information for
figures 17, 20, and 23, which appear in
MINI-SCREEN manual 44895.
110.0 mm
(4.33")
100.0 mm
(3.94 ")
7.4 mm
(0.29")
60.8 mm
(2.40")
85.3mm
(3.36")
35.0 mm
(1.38")
DIN Mounting Slot
Combo Head (Phillips/Slotted) Screws
M3.5 x 0.6 mm x 14 mm (2) (#6 x 0.5" equivalent) (Supplied)
M3.5 mm Washers (2) (#6 equivalent) (Supplied)
M3.5 mm x 0.6 mm Nuts (2) (36 equivalent) (Supplied)
Recommended torque is 16 in-lbs on mounting screws
83.8 mm
(3.30")
7.1 mm
(0.28")
DIN Mounting Tab
(Supplied)
Slot for Screws (2)
M3.5 x 0.6 mm (2)
+24
SSD
18
19
MINI-SCREEN
MODEL NO.
MSDINT-1 or 1L2
LISTED
Presence
Sensing
Device
10Y8
123OK
Diagnostic
Chart on
Reverse Side
FSD2
22
0466
23
FSD1
27
CAUTION
Shock hazard may exist.
28
!
operation always follow the
Blocked or Latched
instructions in the manual.
Clear
Reset
STEADY FLASHING
BANNER ENGINEERING CORP., USA
WARNING
For control reliable
(612) 544-3164
V dcdcCom
32 33 34
Lockout
Blanking
Alignment
PE
12
AUX
or
ALARM
Test 1
or
LATCH
RESET 1
45
Test 2
or
LATCH
RESET 2
89
Key 1 Key 2
15 16 17
13 14
+12VdcCOM T/R T/R DRAIN
Page 2
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 • Phone: (763) 544-3164 • Fax: (763) 544-3573 • E-mail: sensors@baneng.com
MSDINT-1 or MSDINT-1L2
WARNING. . .
Use of MINI-SCREEN
Systems for Perimeter
Guarding
If control module model MSDINT-1T2 is
used for perimeter guarding, the Machine
Primary Control Elements (MPCEs) of the
guarded machine must be wired so that
the trip output of the control module
causes a latched response of the MPCEs.
The MPCEs must be reset only by
actuation of a reset switch.
The reset switch must be located outside
of the area of dangerous motion, and
must be positioned so that the area of the
dangerous motion may be observed by
the switch operator during the reset
operation. Supplemental presence
sensing devices, such as safety mats,
must be used if any space between the
defined area and any danger point is
large enough to allow a person to stand
undetected by the MINI-SCREEN System.
Failure to observe this warning could
result in serious bodily injury or death.
Figure 23. Generic machine interface, MINI-SCREEN System
WARNING. . .
All MINI-SCREEN System output contacts (FSD1, FSD2, and SSD)
must be used. The generalized wiring configuration, shown here, is
provided only to illustrate the importance of proper installation. The
actual details of wiring of the MINI-SCREEN system to any particular machine is
solely the responsibility of the installer and end user.
WARNING. . .
If arc suppressors are used, they MUST BE INSTALLED AS SHOWN
ACROSS THE COILS OF THE MACHINE CONTROL ELEMENTS.
NEVER INSTALL SUPPRESSORS DIRECTLY ACROSS THE
CONTACTS OF THE MINI-SCREEN SWITCHING DEVICES! It is possible for
suppressors to fail as a short circuit. If installed directly across the contacts of a
MINI-SCREEN switching device, a short-circuited suppressor will create an
unsafe condition.
Figure 23 (below) shows output relay connections in a generic interfacing situation.
The connections between the MINI-SCREEN System outputs and the machine primary
and secondary control elements must be direct, and arranged so that any single line
fault or earth fault will not result in a circuit failure to a potentially dangerous state.
!
L (V ac)
or
+ (V dc)
+24V dc
Machine
Control
Circuit
MPCE 1 MPCE 2
MPCE
Monitor
Contacts
MPCE 1 MPCE 2
Model MSDINT-1: Trip Output
Model MSDINT-1L2: Latch Output
Secondary Switching
Device
SSD
Final Switching
Device #2
FSD 2
Final Switching
Device #1
FSD 1
+ (V dc)
– (V dc)
18
19
22
23
27
28
32
33
34
Machine Secondary
Control Element
MSCE
Arc Suppression
(see warning)
Machine Primary
Control Element #2
MPCE
Arc Suppression
(see warning)
Machine Primary
Control Element #1
MPCE
Arc Suppression
(see warning)
2
1
N (V ac)
or
common (V dc)
MINI-SCREEN
Control Module
Earth
Grounddccommon
!
!
Loading...