33.0 mm
(1.30")
16.0 mm
(0.63")
44.0 mm
(1.73")
1.3 mm
(0.05")
22.0 mm
(0.87")
13.0 mm
(0.51")
5.0 mm
(0.20")
35.0 mm
(1.38")
2 x ø3.3 mm (0.125")
max. torque
0.7 Nm (6 in lbs)
M30 x 1.5 Thread
max. torque
6 Nm (53 in lbs)
with included 30 mm
mounting nut
Yellow LED
Output
Indicator
Yellow and Green LEDs
12.5 mm
(0.47")
!
P
bn
bu
wh
bk
gy
+
10 - 30V dc
–
Load
Load
LO/DO Select
bn
bu
wh
bk
+
10 - 30V dc
No Connection
–
gy
bn
bu
-
+
10-30V dc
bn
bu
wh
bk
+
10 - 30V dc
–
Load
Load
gy
LO/DO Select
WORLD-BEAM
®
QS30 – DC Voltage
Compact, self-contained photoelectric sensors in universal-style housing
Additional information on this product is immediately available online at www.bannerengineering.com/119165
View or download additional information, including excess gain curves, beam patterns and accessories.
For further assistance, contact a Banner Engineering Applications Engineer at (763) 544-3164 or (888) 373-6767.
Sensing Mode Range Output Model*
875 nm Infrared
Effective Beam:
18 mm (0.7")
630 nm Visible Red
Opposed
Retroreflective
60 m (200')
12 m (40')
†
–
Installation
Guide
QS30E
QS30R
QS30LV
Cabled Emitters
QD Emitters
(5-pin Euro-Style)
All Other Cabled Models
All Other QD Models
(5-pin Euro-Style)
630 nm Visible Red
Polarized Retroreflective
8 m (26')
†
Bipolar
QS30LP
NPN/PNP
940 nm Infrared
Diffuse
680 nm Visible Red
Fixed-Field
1 m (3.3')
200 mm (8")
400 mm (16")
600 mm (24")
QS30D
QS30FF200
QS30FF400
QS30FF600
* Only standard 2 m (6.5') cable models are listed. For 9 m (30') integral cable, add suffix “W/30” to
the model number (e.g., QS30E W/30).
QD models: For 5-pin integral Euro-style QD, add suffix “Q” (e.g., QS30EQ).
†
Range is specified using a model BRT-84 retroreflector.
Dimensions
Cabled Models
QD Models
WARNING . . .
Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.
Not To Be Used for Personnel Protection
These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety
applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition.
Consult your current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for
personnel protection.
Printed in USA 04/09 P/N 119167 rev. A
WORLD BEAM® QS30 – DC Voltage
White Wire
Blue Wire
Black Wire
Brown Wire
Gray Wire
M12 x 1
ø 15 mm
(0.6")
44 mm max.
(1.7")
38 mm max.
(1.5")
M12 x 1
ø 15 mm
(0.6")
38 mm max.
(1.5")
Specifications
Supply Voltage and Current
10 to 30V dc (10% maximum ripple) at less than 40 mA, exclusive of load
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Output Configuration
Bipolar: One current sourcing and one current sinking
Rating: 100 mA maximum each output at 25°C
Off-state leakage current: NPN: less than 200 µA
PNP: less than 10 µA
ON-state saturation voltage: NPN: less than 1.6V @ 100 mA
PNP: less than 2.0V @ 100 mA
Protected against false pulse on power-up and continuous overload or short
circuit of outputs
Output Response Time
Opposed Mode: 5 milliseconds ON and OFF
All others: 2 milliseconds
NOTE: 100 millisecond delay on power-up; outputs do not conduct during
this time
Repeatability
Opposed Mode: not applicable
All others: 500 microseconds
Cutoff Point Tolerance
Fixed-Field only: ±5% of nominal cutoff distance
Indicators
2 LED indicators on sensor top:
Green ON steady: Power ON Yellow ON steady: Light sensed
Green flashing: Output overloaded Yellow flashing: Marginal excess gain
(except receivers) (1.0 to 1.5x excess gain)
Large oval LED indicator on sensor back (except emitters):
Yellow ON steady: Output conducting
Adjustments
Diffuse, Retroreflective, and Polarized Retroreflective mode models:
Single-turn Sensitivity (Gain) adjustment potentiometer
All models: Selectable Light/Dark Operate is achieved via the gray wire, as
described below.
Opposed, Retroreflective, and Polarized Retroreflective models:
Light Operate - Low (0 to 3V)*
Dark Operate - High (open or 5 to 30V)*
Diffuse and Fixed-Field models:
Light Operate - High (open or 5 to 30V)*
Dark Operate - Low (0 to 3V)*
* Input impedance 10 kΩ
Construction
ABS housing, rated IEC IP67; NEMA 6; Acrylic lens cover
3 mm mounting hardware included
Connections
2 m (6.5') or 9 m (30') 5-wire PVC cable, or 5-pin Euro-style integral QD
connector
Operating Conditions
Temperature: -20° to +70° C (-4° to +158° F)
Relative Humidity: 90% @ 50° C (non-condensing)
Vibration and Mechanical Shock
All models meet Mil. Std. 202F requirements method 201A (vibration: 10
to 60 Hz max., double amplitude 0.06", maximum acceleration 10G). Also
meets IEC 947-5-2; 30G 11 ms duration, half sine wave.
Certifications
Style Model Length Dimensions Pin-Out
5-pin
Euro-style
straight
5-pin
Euro-style
right-angle
MQDC1-506
MQDC1-515
MQDC1-530
MQDC1-506RA
MQDC1-515RA
MQDC1-530RA
2 m (6.5')
5 m (15')
9 m (30')
2 m (6.5')
5 m (15')
9 m (30')
Additional information on this product is immediately available online at www.bannerengineering.com/119165
View or download additional information, including excess gain curves, beam patterns and accessories.
For further assistance, contact a Banner Engineering Applications Engineer at (763) 544-3164 or (888) 373-6767.
P/N 119167 rev. A
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com
Quick-Disconnect (QD) Cables
WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for
one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its
manufacture found to be defective at the time it is returned to the factory during the warranty
period. This warranty does not cover damage or liability for the improper application of
Banner products. This warranty is in lieu of any other warranty either expressed or implied.
Loading...