Banner LAT-1 Series Laser Alignment Tools User Manual

LASER LIGHT

REQUIRES ONE 9V BATTERY

DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT.

REMOVE TWO PHILLIPS SCREWS FOR BATTERY ACCESS BELOW

Peak Power:

COMPLIES WITH 21 CFR PART

1040.10 AND EN60825-1; 1994

2.8mW, 640-660nm
33kHz 25% duty cycle

LAT - 1

AVOID EXPOSURE - LASER LIGHT

EMITTED FROM THIS APERTURE

LAT-1-x Laser Alignment Tool

0 054599 0

Visible Laser Device for Aligning Light Screen and Grid Systems

• Self-contained visible-beam laser tool simplifies the alignment of any opposed­mode sensor pair, especially in applications that include long distances or corner
mirrors

• Reduces the time required to align light screen systems and corner mirrors; elim­inates much trial-and-error guesswork when working with infrared beams

• Uses one common 9-volt battery (included)

• Built-in circular bubble level

• One 4" x 4" square of high-grade retroreflective target material included for easy
viewing of the laser spot at long distances

• Mounting clip (available separately or as part of a kit; see below) snaps squarely
onto the housings of Banner safety light screen/grid emitters and receivers

Emitter/Receiver Housing LAT-1 with Clip(s) Kit Clip Only

MINI-SCREEN® LAT-1-MS MSA-LAT-1

MICRO-SCREEN® LAT-1-US USA-LAT-1

EZ-SCREEN™ LAT-1-SS EZA-LAT-2

EZ-SCREEN™ Type 2 LAT-1-LS LSA-LAT-2

MINI-SCREEN® H.D., EZ-SCREEN™
Grid or Point

EZ-SCREEN™ LP LAT-1-LP LPA-LAT-2

All of the Above LAT-1 -

EZ-SCREEN™ Type 2 Heavy Duty LAT-1-LSHD LSHDA-LAT-2

PICO-GUARD™ SFP12 Safety Points LAT-1-SFP12 -

PICO-GUARD™ SFP30 Safety Points LAT-1-SFP30 -

P/N 054599 Rev. E 9/25/2012

Model Model

LAT-1-HD EZA-LAT-1

CAUTION: Laser Light Can Damage Your Eyes

• View only the diffuse image of the laser beam where it
strikes the alignment target.

• Always view the laser image from behind the LAT-1.

• Never look directly into the laser lens or into a mirror re­flection of the laser light beam.

See alignment procedure for more information. Failure to fol­low these guidelines can result in vision damage.

Screw-On Mounting Bracket

(Screws to Alignment Tool; Screws onto

SFP12/30 Safety Point Housing)

SFP12

SFP30

REMOVE TWO PHILLIPS SCREWS FOR BATTERY ACCESS BELOW

DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT.

AVOID EXPOSURE - LASER LIGHT
EMITTED FROM THIS APERTURE

REQUIRES ONE 9V BATTERY

LASER LIGHT

LAT - 1

Peak Power:

2.8 mW, 640-660nm
33kHz 25% duty cycle

COMPLIES WITH 21 CFR PART

1040.10 AND EN60825-1; 1994

Emitter
Centerline

40 mm

(1.6")

21 mm
(0.8")

75 mm

(3.0")

75 mm

(3.0")

ON/OFF Switch

Snap-On Mounting Bracket
(Screws to Alignment Tool;
Snaps onto Light Screen Emitter or Receiver)

Circular Bubble
Level

LAT-1-x Laser Alignment Tool

Figure 2. Dimensions

Figure 1. Screw-On Mounting Bracket

Specifications

Supply Voltage and Current

One standard 9V battery, included (replaceable); ap­proximately 20 hours of continuous operation

Construction

Aluminum housing; black anodized finish
Black polypropylene cover with flexible hinge for bat-

tery access

Environmental Rating

NEMA 1; IEC IP50

Operating Conditions

Temperature: 0° to +40°C (+32° to 104°F)
Maximum Relative Humidity: 90% @ +50°C (non-con-

densing)

Application Notes

See Caution on page 1 regarding safe use of laser
beam.

Sensing Beam

Class 2 laser, 640-660 nm visible red IEC
Pulse Width: 7 μs
Rep rate: 30 μs
Peak output power: 2.8 mW, 33kHz, 25% duty cycle

Beam Size at Aperture

Approximately 2 mm (0.08”) diameter

Beam Divergence

± 1.0 milliradian within specified temperature range
± 0.5 milliradians at room temperature

Beam Placement

Within ± 4 milliradians (approximately ±0.25 degrees)
of parallel to front, back, top and bottom of housing

Laser Classification

U.S. Safety Standards 21 CFR 1040.10
European Standards EN 60825-1:1994

2 www.bannerengineering.com - tel: [phone] P/N 054599 Rev. E