Banner DF-G1-PS-Q7, DF-G1-PS-2M, DF-G1-NS-Q5, DF-G1-NS-2M, DF-G1-KS-Q7 User Manual

DF-G1 Expert™ Dual Display Fiber Amplifier

161275

Installation Guide

Advanced sensor with dual digital displays for use with plastic and glass fiber optic assemblies.

For complete technical information about this product, including dimensions, accessories, and specifications, see

www.bannerengineering.com and search 161999.

Overview

1 Output LED

2 LO/DO Switch

3 RUN/PRG/ADJ Mode Switch

4 Lever Action Fiber Clamp

5 Red Signal Level

6 Green Threshold

7 +/SET/- Rocker Button

Figure 1. DF-G1 Model Features

WARNING: Not To Be Used for Personnel Protection

Never use this device as a sensing device for personnel protection. Doing so could lead to
serious injury or death. This device does not include the self-checking redundant circuitry necessary

to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an
energized or de-energized sensor output condition.

http://

Models

Model Outputs Connector

DF-G1-NS-2M Single NPN

DF-G1-PS-2M Single PNP

DF-G1-KS-2M Dual outputs, 1 push-pull IO-Link and 1

DF-G1-NS-Q5 Single NPN

DF-G1-PS-Q5 Single PNP

DF-G1-KS-Q5 Dual outputs, 1 push-pull IO-Link and 1

DF-G1-NS-Q7 Single NPN

DF-G1-PS-Q7 Single PNP

DF-G1-KS-Q7

1

Connector options:

• A model with a QD connector requires a mating cordset .

• For 9 m cable, change the suffix 2M to 9M in the 2 m model number (example, DF-G1-NS-9M).

• For 150 mm (6 in) PVC pigtail, M8 Pico QD connector, 4-pin change the suffix 2M to Q3 in the 2 m model number (example, DF-G1-NS-Q3).

PNP (complementary outputs)

PNP (complementary outputs)

Dual outputs, 1 push-pull IO-Link and 1
PNP (complementary outputs)

2 m (6.5 ft) cable, 4-wire

150 mm (6 in) PVC pigtail, M12 Euro QD connector,
4-pin

Integral M8 Pico QD connector, 4-pin

1

Original Document
161275 Rev. D

9 September 2015

Fiber Emitter
Port

Fiber Receiver

Fiber Clamp

Port

Move forward
to release the
fibers

DF-G1 Expert™

Installation Instructions

Mounting Instructions

Mount on a DIN Rail

1. Hook the DIN rail clip on the bottom of the DF-G1
over the edge of the DIN rail (1).

Push the DF-G1 up on the DIN rail (1).

2.

3. Pivot the DF-G1 onto the DIN rail, pressing until it
snaps into place (2).

Mount to the Accessory Bracket

1. Position the DF-G1 in the SA-DIN-BRACKET.

2. Insert the supplied M3 screws.

3. Tighten the screws.

Dual Display Fiber Amplifier

Remove from a DIN rail

1. Push the DF-G1 up on the DIN rail (1).

2. Pivot the DF-G1 away from the DIN rail and remove
it (2).

Installing the Fibers

Follow these steps to install glass or plastic fibers.

Open the dust cover.

1.

2. Move the fiber clamp forward to unlock it.

3. Insert the fiber(s) into the fiber port(s) until they
stop.

4. Move the fiber clamp backward to lock the fiber(s).

5. Close the dust cover.

Fiber Adapters

NOTE: If a thin fiber with less than 2.2 mm outer diameter is used, install the fiber adapter provided

with the fiber assembly to ensure a reliable fit in the fiber holder. Banner includes the adapters with all
fiber assemblies.

2 www.bannerengineering.com - Tel: [phone] P/N 161275 Rev. D

TO

FIBERS

TO

SENSOR

TRANSMITTER

RECEIVER

Single-core fiber

Multi-core fiber

Remote
Programming
(N.O.)

10-30V dc

Load

Load

10–30 V dc

Remote
Programming
(N.O.)

(C/Q)

(Q)

PUSH-PULL

18-30V dc

Load

Load

DF-G1 Expert™ Dual Display Fiber Amplifier

Fiber Outer Diameter (mm) Adapter Color

Ø 1.0 Black

Ø 1.3 Red

Ø 2.2 No adapter needed

When connecting coaxial-type fiber assemblies to the amplifier, install the single-core fiber to the Transmitter port, and the
multi-core fiber to the Receiver port. This will result in the most reliable detection.

Wiring Diagrams

NPN Models

NOTE: Open lead wires must be connected to a terminal block.

IO-Link Models

PNP Models

Key

1 = Brown
2 = White
3 = Blue
4 = Black

P/N 161275 Rev. D www.bannerengineering.com - Tel: [phone]