Axis Q1755 Installation
INSTALLATION GUIDE
AXIS Q1755 Network Camera
ENGLISH DEUTSCH
FRAN
Ç
AIS
ITALIANO
ESPAÑOL
About this Document
This document includes instructions for installing the
AXIS Q1755 Network Camera on your network. Previous
experience of networking will be beneficial when
installing the product.
Legal Considerations
Video and audio surveillance can be prohibited by laws
that vary from country to country. Check the laws in
your local region before using this product for
surveillance purposes.
This product includes one (1) H.264 decoder license. To
purchase further licenses, contact your reseller.
Electromagnetic Compatibility (EMC)
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures: Re-orient or relocate
the receiving antenna. Increase the separation between
the equipment and receiver. Connect the equipment to
an outlet on a different circuit to the receiver. Consult
your dealer or an experienced radio/TV technician for
help. Shielded (STP) network cables must be used with
this unit to ensure compliance with EMC standards.
USA - This equipment has been tested and found to
comply with the limits for a Class B computing device
pursuant to Subpart B of Part 15 of FCC rules, which are
designed to provide reasonable protection against such
interference when operated in a commercial
environment. Operation of this equipment in a
residential area is likely to cause interference, in which
case the user at his/her own expense will be required to
take whatever measures may be required to correct the
interference.
Canada - This Class B digital apparatus complies with
Canadian ICES-003.
Europe - This digital equipment fulfills the
requirements for radiated emission according to limit B
of EN55022, and the requirements for immunity
according to EN55024 residential and commercial
industry.
Japan - This is a class B product based on the standard
of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used
near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and
use the equipment according to the instruction manual.
Australia - This electronic device meets the
requirements of the Radio communications
(Electromagnetic Compatibility) Standard AS/NZS
CISPR22.
Equipment Modifications
This equipment must be installed and used in strict
accordance with the instructions given in the user
documentation. This equipment contains no
user-serviceable components. Unauthorized equipment
changes or modifications will invalidate all applicable
regulatory certifications and approvals.
Liability
Every care has been taken in the preparation of this
document. Please inform your local Axis office of any
inaccuracies or omissions. Axis Communications AB
cannot be held responsible for any technical or
typographical errors and reserves the right to make
changes to the product and documentation without
prior notice. Axis Communications AB makes no
warranty of any kind with regard to the material
contained within this document, including, but not
limited to, the implied warranties of merchantability
and fitness for a particular purpose. Axis
Communications AB shall not be liable nor responsible
for incidental or consequential damages in connection
with the furnishing, performance or use of this material.
RoHS
This product complies with both the European
RoHS directive, 2002/95/EC, and the Chinese
RoHS regulations, ACPEIP.
WEEE Directive
The European Union has enacted a Directive
2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE Directive). This directive is
applicable in the European Union member
states.
The WEEE marking on this product (see right) or its
documentation indicates that the product must not be
disposed of together with household waste. To prevent
possible harm to human health and/or the environment,
the product must be disposed of in an approved and
environmentally safe recycling process. For further
information on how to dispose of this product correctly,
contact the product supplier, or the local authority
responsible for waste disposal in your area.
Business users should contact the product supplier for
information on how to dispose of this product correctly.
This product should not be mixed with other commercial
waste.
Support
Should you require any technical assistance, please
contact your Axis reseller. If your questions cannot be
answered immediately, your reseller will forward your
queries through the appropriate channels to ensure a
rapid response. If you are connected to the Internet, you
can:
• download user documentation and firmware updates
• find answers to resolved problems in the FAQ database.
Search by product, category, or phrases
• report problems to Axis support by logging in to your
private support area.
The AXIS Q1755 uses a 3.0V CR2032 Lithium battery,
for more information please see
page 73.
AXIS Q1755 Installation Guide Page 3
Important!
This product must be used in
compliance with local laws and
regulations.
AXIS Q1755 Installation Guide
This installation guide provides instructions for installing the AXIS Q1755 Network Camera on your
network. For all other aspects of using the product, please see the User’s Manual, available on the
CD included in this package, or from www.axis.com/techsup
Installation steps
1. Check the package contents against the list below.
2. Hardware overview. See page 4.
3. Install the hardware. See page 5.
4. Assign an IP address. See page 6.
5. Set the password. See page 9.
Package contents
Item Models/variants/notes
Network camera AXIS Q1755 50Hz/60Hz
Terminal block connector (1) 4-pin connector for connecting external devices to the I/O terminal
connector
(1) 3-pin connector for power connection
(2) 2-pin connector for RS-485/422 connection
Camera stand Metal stand supplied with mounting screws
CD AXIS Network Video Product CD, including product documentation,
installation tools and other software
Printed materials AXIS Q1755 Installation Guide (this document)
Axis Warranty Document
Optional accessories See www.axis.com for information on power accessories and outdoor housings
ENGLISH
Page 4 AXIS Q1755 Installation Guide
Part number (P/N) & Serial number (S/N).
The serial number may be required
during the installation.
Network indicator LED
Status indicator LED
Control button
Power connector
see page 12
Network
connector
see page 12
Power indicator LED
Audio out
Microphone
I/O connector
see page 12
RS-485/422
connector
Audio in
Video out
SD memory
card slot
Y/Pb/Pr/CVBS
CVBS
button
The camera is designed to be installed with the
Hole for wall/ceiling
stand
logotype facing down.
Hardware overview
IMPORTANT! - To use AXIS Q1755 outdoors, it must be installed in an approved
!
outdoor housing. Please see www.axis.com for more information on outdoor housings.
AXIS Q1755 Installation Guide Page 5
CVBS button
CVBS
connector
(2 min.)
Install the hardware
Attach the metal stand to the camera and use the appropriate screws for the wall/ceiling material.
Note that the camera is designed to be installed with the logotype facing down.
Connect the cables
1. Optionally connect external input/output devices, e.g. alarm devices. See page 12 for information on the terminal connector pins.
2. Optionally connect an active speaker and/or external microphone.
3. Connect the camera to the network using a shielded network cable.
4. Connect power, using one of the methods listed below:
• PoE (Power over Ethernet, Class 3). If available, this is automatically detected when the
network cable is connected.
• Connect an external power adapter to the power connector block, see Unit connectors, on
page 12 for wiring information.
5. Check that the indicator LEDs indicate the correct conditions. See the table on page 14 for
further details.
Composite video out (optional)
For quick and easy installation, follow these instructions to view the video signal in a connected
video monitor.
ENGLISH
1. Follow the instructions in Connect the cables, on page 5.
2. Using a composite video cable, connect a video monitor to the Video out Pr/CVBS connector
(red) on the AXIS Q1755.
3. Press and hold the CVBS button for 5 seconds to switch to composite video out (installation
mode).
Note: AXIS Q1755 will stay in installation mode for two (2) minutes and then automatically
revert to Component video. If additional time is required, press the button again.
4. Position the camera and check that the intended area is in
view on the screen.
5. Disconnect the video monitor.
Component video out (optional)
Follow these instructions to view the video signal directly in a
connected HDTV video monitor.
1. Follow the instructions in Connect the cables, on page 5.
2. Connect AXIS Q1755 directly to an HDTV monitor using a component video cable connected to
the Video Out Y/Pb/Pr connectors.
Once the cables have been connected, proceed to Assign an IP address, on page 6.
Page 6 AXIS Q1755 Installation Guide
Assign an IP address
Most networks today have a DHCP server that automatically assigns IP addresses to connected
devices. If your network does not have a DHCP server the AXIS Q1755 will use 192.168.0.90 as the
default IP address.
If you would like to assign a static IP address, the recommended method in Windows is either AXIS
IP Utility or AXIS Camera Management. Depending on the number of cameras you wish to install,
use the method that best suits your purpose.
Both of these free applications are available on the Axis Network Video Product CD supplied with
this product, or they can be downloaded from www.axis.com/techsup
Method Recommended for Operating system
AXIS IP Utility
See page 7
AXIS Camera Management
See page 8
Notes:
• If assigning the IP address fails, check that there is no firewall blocking the operation.
• For other methods of assigning or discovering the IP address of the AXIS Q1755 e.g. in other
operating systems, see page 11.
Single camera
Small installations
Multiple cameras
Large installations
Installation on a different subnet
Windows
Windows 2000
Windows XP Pro
Windows 2003 Server
Windows Vista
AXIS Q1755 Installation Guide Page 7
AXIS IP Utility - single camera/small installation
AXIS IP Utility automatically discovers and displays Axis devices on your network. The application
can also be used to manually assign a static IP address.
Note that the computer running AXIS IP Utility must be on the same network segment (physical
subnet) as the AXIS Q1755.
Automatic discovery
1. Check that the AXIS Q1755 is connected to the network and that power has been applied.
2. Start AXIS IP Utility.
3. When the camera appears in the window, double-click it to open its home page.
4. See page 9 for instructions on how to assign the password.
ENGLISH
Assign the IP address manually (optional)
1. Acquire an unused IP address on the same network segment as your computer.
2. Select the AXIS Q1755 in the list.
3. Click the button Assign new IP address to the selected device and enter the IP address.
4. Click the Assign button and follow the on-screen instructions. Note that the camera must be
restarted within 2 minutes for the new IP address to be set.
5. Click the Home Page button to access the camera’s web pages.
6. See page 9 for instructions on how to set the password.
Page 8 AXIS Q1755 Installation Guide
AXIS Camera Management - multiple cameras/large installations
AXIS Camera Management can automatically discover multiple Axis devices, show connection
status, manage firmware upgrades and set IP addresses.
Automatic discovery
1. Check that the camera is connected to the network and that power has been applied.
2. Start AXIS Camera Management. When the AXIS Q1755 appears in the window, right-click the
link and select Live View Home Page.
3. See page 9 for instructions on how to set the password.
Assign an IP address in a single device
1. Select AXIS Q1755 in AXIS Camera Management and click the
Assign IP button.
2. Select Assign the following IP address and enter the IP
address, subnet mask and default router the device will use.
3. Click the OK button.
Assign IP addresses in multiple devices
AXIS Camera Management speeds up the process of assigning IP
addresses to multiple devices, by suggesting IP addresses from a
specified range.
1. Select the devices you wish to configure (different models can
be selected) and click the Assign IP button.
2. Select Assign the following IP address range and enter the
range of IP addresses, the subnet mask and default router the
devices will use.
3. Click the OK button.
AXIS Q1755 Installation Guide Page 9
To configure the password directly
via an unencrypted connection, enter
the password here.
To create an HTTPS connection,
start by clicking this button.
Set the password
To gain access to the product, the password for the default administrator user root must be set. This
is done in the ‘Configure Root Password’ dialog, which is displayed when the AXIS Q1755 is
accessed for the first time.
To prevent network eavesdropping when setting the root password, this can be done via an
encrypted HTTPS connection, which requires an HTTPS certificate (see note below).
To set the password via a standard HTTP connection, enter it directly in the first dialog shown
below.
To set the password via an encrypted HTTPS connection, follow these steps:
1. Click the Create self-signed certificate button.
2. Provide the requested information and click OK. The certificate is created and the password can
now be set securely. All traffic to and from the AXIS Q1755 is encrypted from this point on.
3. Enter a password and then re-enter it to confirm the spelling. Click OK. The password has now
been configured.
ENGLISH
4. To log in, enter the user name “root” in the dialog as requested
Note: The default administrator user name root cannot be deleted.
5. Enter the password as set above, and click OK.
Page 10 AXIS Q1755 Installation Guide
Setup - Provides all the
tools for configuring the
camera to requirements.
Help - Displays
online help on all
aspects of using
the camera.
Access the video stream
The Live View page of the AXIS Q1755 is displayed, with links to the Setup tools, which allow you to
customize the camera.
If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the video stream
in Internet Explorer. You will need administrator rights on the computer to do this.
Notes:
• HTTPS (Hypertext Transfer Protocol over Secure Socket Layer) is a protocol used to encrypt the traffic
between web browsers and servers. The HTTPS certificate controls the encrypted exchange of
information.
• The default administrator user root cannot be deleted.
• If the password for root is lost or forgotten, the AXIS Q1755 must be reset to the factory default
settings. See Resetting to the Factory Default Settings, on page 15.
AXIS Q1755 Installation Guide Page 11
Other methods of setting the IP address
The table below shows the other methods available for setting or discovering the IP address. All
methods are enabled by default, and all can be disabled.
UPnP™
Bonjour
AXIS Dynamic DNS
Service
ARP/Ping
View DHCP server
admin pages
Use in operating
system
Windows
(ME or XP)
MAC OSX
(10.4 or later)
All A free service from Axis that allows you to quickly and simply
All See below. The command must be issued within 2 minutes of
All To view the admin pages for the network DHCP server, see the
Notes
When enabled on your computer, the camera is automatically
detected and added to “My Network Places.”
Applicable to browsers with support for Bonjour. Navigate to the
Bonjour bookmark in your browser (e.g. Safari) and click on the
link to access the camera’s web pages.
install your camera. Requires an Internet connection with no
HTTP proxy. See www.axiscam.net for more information.
connecting power to the camera.
server’s own documentation.
Set the IP address with ARP/Ping
1. Acquire an IP address on the same network segment your computer is connected to.
2. Locate the serial number (S/N) on the product label on the camera.
3. Open a command prompt on your computer and enter the following commands:
Windows syntax: Windows example:
arp -s <IP Address> <Serial Number>
ping -l 408 -t <IP Address>
UNIX/Linux/Mac syntax: UNIX/Linux/Mac example:
arp -s <IP Address> <Serial Number> temp
ping -s 408 <IP Address>
arp -s 192.168.0.125 00-40-8c-18-10-00
ping -l 408 -t 192.168.0.125
arp -s 192.168.0.125 00:40:8c:18:10:00 temp
ping -s 408 192.168.0.125
ENGLISH
4. Check that the network cable is connected to the camera and then start/restart the camera, by
disconnecting and reconnecting power.
5. Close the command prompt when you see ‘Reply from 192.168.0.125: ...’ or similar.
6. In your browser, type in http://<IP address> in the Location/Address field and press Enter on
your keyboard.
Notes:
• To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.
• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.
Page 12 AXIS Q1755 Installation Guide
4
321
Pins
RS-485/422
RX/TX TX
+
~
~
Unit connectors
Network - RJ-45 Ethernet connector. Supports PoE (Power over Ethernet, class 3). Using shielded
cables is recommended.
Audio in - 3.5mm input for a mono microphone, or a line-in mono signal (left channel is used from
a stereo signal).
Audio out - 3.5mm output for audio (line level), can be connected to a public address (PA) system
or an active speaker with a built-in amplifier. A pair of headphones can also be connected. A stereo
connector must be used for audio out.
Video Out - RCA connectors for component or composite
video out.
• Component video out for HDTV video, e.g. an entrance
camera connected to an HDTV screen
• Composite video (CVBS) - for easy installation using a
video monitor
RS-485/422 - two 2-pin terminal blocks for RS-485/422
serial interface used to control auxiliary equipment, e.g. PTZ devices.
The RS-485/422 serial port can be configured in the following port modes:
• Bidirectional RS-485 half-duplex port for data transmission using
two wires, one combined RX/TX pair.
• Bidirectional RS-485 full-duplex port for data transmission using
four wires, one RX pair and one TX pair.
• Unidirectional RS-422 port for transmitting or receiving data using
two wires, RX- or TX pair.
• Bidirectional RS-422 full-duplex port for data transmission (point-to-point) using four
wires, one RX pair and one TX pair.
Function Pin Notes
RS 485/422TX(A) 1 TX pair for RS-422 and 4-wire RS-485
RS 485/422TX(B) 2
RS-485A alt RS-485/422RX(A) 3 RX pair for all modes (combined RX/TX for 2-wire RS-485)
RS-485B alt RS-485/422RX(B) 4
SDHC memory card slot - High capacity SD memory card used for local recording and removable
storage.
Power - 3-pin terminal block 8-20 VDC or 20-24 VAC
AXIS Q1755 Installation Guide Page 13
4321
I/O terminal connector - Used in applications for e.g. motion detection, event
triggering, time lapse recording and alarm notifications. In addition to an auxiliary
power and a GND pin, the AXIS Q1755 has 2 pins that can be configured as either
input or output. These pins provide the interface to:
• Transistor output - For connecting external devices such as relays and
LEDs. Connected devices can be activated by AXIS VAPIX API, output buttons on the Live
View page or by an Event Type. The output will show as active (shown under Event Configuration > Port Status) if the alarm device is activated.
• Digital input - An alarm input for connecting devices that can toggle between an open and
closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a
signal is received the state changes and the input becomes active (shown under Event
Configuration > Port Status.)
Function Pin number Notes Specifications
GND 1 Ground
3.3V DC
Power
Configurable
(Input or
Output)
2 Can be used to power auxiliary equipment.
Note:
This pin can only be used as power out.
3 - 4 Digital input - Connect to GND to activate, or
leave floating (or unconnected) to deactivate.
Digital output - Uses an open-drain NFET
transistor with the source connected to GND.
If used with an external relay, a diode must
be connected in parallel with the load, for
protection against voltage transients.
Max load = 250mA
Min input = - 40V DC
Max input = + 40V DC
Max load = 100mA
Max voltage = + 40V DC
ENGLISH
Page 14 AXIS Q1755 Installation Guide
AXIS Q1755
3.3V max 250mA
1
2
3
4
E.g. push button
D
S
G
I/O configured as input
I/O configured as output
3.3V
Connection diagram
LED indicators
LED Color Indication
Network Green Steady for connection to a 100 Mbit/s network. Flashes for network activity.
Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.
Unlit No network connection.
Status Green Steady green for normal operation.
Amber Steady during startup, during reset to factory default or when restoring settings.
Red Slow flash for failed upgrade.
Power Green Normal operation.
Amber Flashes green/amber during firmware upgrade.
Note: The Status LED can be configured to be unlit during normal operation, or to
flash only when the camera is accessed. To configure, go to Setup > System
Options > LED. See the online help files for more information.
AXIS Q1755 Installation Guide Page 15
Tip!
Visit www.axis.com/techsup to check if there is updated firmware available for your AXIS
Q1755. To see the currently installed firmware version, see Setup > About.
Resetting to the Factory Default Settings
This will reset all parameters, including the IP address, to the Factory Default settings:
1. Disconnect power from the camera.
2. Press and hold the Control button and reconnect power.
3. Keep the Control button pressed until the Status indicator displays amber (this may take up to
15 seconds).
4. Release the Control button. When the Status indicator displays green (which can take up to 1
minute) the process is complete and the camera has been reset.
5. Re-assign the IP address, using one of the methods described in this document.
It is also possible to reset parameters to the original factory default settings via the web interface.
For more information, please see the online help or the user’s manual.
Accessing the camera from the Internet
Once installed, your AXIS Q1755 is accessible on your local network (LAN). To access the camera
from the Internet, network routers must be configured to allow incoming traffic, which is usually
done on a specific port
• HTTP port (default port 80) for viewing and configuration
• RTSP port (default port 554) for viewing H.264 video streams
Please refer to the documentation for your router for further instructions. For more information on
this and other topics, visit the Axis Support Web at www.axis.com/techsup
ENGLISH
Further information
The user’s manual is available from the Axis Web site at www.axis.com or from the Axis Network
Video Product CD supplied with this product.
AXIS Q1755 Guide d'installation Page 17
Important !
Ce produit doit être utilisé
conformément aux lois et
dispositions locales en vigueur.
AXIS Q1755 Guide d'installation
Ce guide d'installation explique comment installer l'AXIS Q1755 Caméra réseau sur votre réseau.
Pour toute autre question concernant l’utilisation du produit, reportez-vous au Manuel de
l’utilisateur, que vous trouverez sur le CD joint ou sur le site www.axis.com/techsup
Procédure d'installation
1. Vérification du contenu de l’emballage par rapport à la
liste ci-dessous.
2. Vue d’ensemble du matériel. Reportez-vous à la section
page 18.
3. Installation du matériel. Reportez-vous à la section page
19.
4. Attribution d’une adresse IP. Reportez-vous à la section
page 20.
5. Configuration du mot de passe. Reportez-vous à la page
23.
Contenu de l'emballage
FRAN
Ç
AIS
Article Modèles/variantes/remarques
Caméra réseau AXIS Q1755 50 Hz/60 Hz
Bloc de connexion pour
terminaux
Support de caméra Support en métal fourni avec les vis de fixation
CD CD de la caméra vidéo sur IP Axis comprenant la documentation,
Documentation Guide d'installation de l’AXIS Q1755 (le présent document)
Accessoires en option Pour tout complément d'information sur les accessoires d'alimentation et les
(1) Connecteur à 4 broches pour le raccordement d'équipements externes au
connecteur pour terminaux E/S
(1) Connecteur à 3 broches pour le branchement de l'alimentation
(2) Connecteur à 2 broches pour le branchement du connecteur RS-485/422
les outils d'installation et les autres logiciels
Document de garantie d'Axis
boîtiers d'extérieur, allez sur le site Web www.axis.com.
Page 18 AXIS Q1755 Guide d'installation
Référence et numéro de série.
Le numéro de série peut
être demandé pendant l'installation.
Voyant réseau
Voyant d’état
Bouton de
commande
Connecteur d’alimentation
cf. page 27
Connecteur
réseau
cf. page 27
Voyant d'alimentation
Sortie audio
Microphone
Connecteur E/S
cf. page 27
Connecteur
RS-485/422
Entrée audio
Sortie vidéo
Logement de carte
mémoire SD
Y/Pb/Pr/CVBS
Bouton
CVBS
La caméra est destinée à être installée
Trou pour support de
logo en bas.
fixation au mur/plafond
Vue d’ensemble du matériel
IMPORTANT ! - Pour pouvoir utiliser l´AXIS Q1755 en extérieur, la caméra doit être
!
placée dans un boîtier d'extérieur homologué. Visitez le site www.axis.com pour plus
d'informations sur les caissons d'extérieur.
AXIS Q1755 Guide d'installation Page 19
Bouton CVBS (2 min.)
Connecteur CVBS
Installation du matériel
Fixez le support en métal sur la caméra et utilisez les vis appropriées au mur/plafond. Notez que la
caméra est destinée à être installée logo en bas.
Branchement des câbles
1. Si vous le souhaitez, connectez des dispositifs d’entrée/sortie externes, par exemple des
systèmes d'alarme. Reportez-vous à la page 27 pour plus d'informations sur les broches du
connecteur pour terminaux.
2. Si vous le souhaitez, branchez un haut-parleur actif et/ou un micro externe.
3. Connectez la caméra à votre réseau à l'aide d'un câble réseau blindé.
4. Branchez l'alimentation en suivant une des méthodes décrites ci-dessous :
• PoE (alimentation par Ethernet, classe 3). Si elle est disponible, elle est automatiquement
détectée quand le câble réseau est connecté.
• Branchez un adaptateur secteur externe sur le bloc de connexion d'alimentation. Cf.
Connecteurs de l’appareil, à la page 27 pour toute information sur le câblage.
5. Vérifiez que les voyants lumineux indiquent les conditions correctes. Pour plus d'informations,
reportez-vous au tableau de la page 29.
Sortie vidéo composite (en option)
Pour une installation rapide et aisée, procédez comme suit afin de voir le signal vidéo sur un écran
de contrôle connecté.
1. Suivez les instructions de la section Branchement des câbles, à la page 19.
2. À l'aide d'un câble vidéo composite, branchez un écran de contrôle sur le connecteur (rouge) de
sortie vidéo Pr/CVBS de l'AXIS Q1755.
3. Appuyez sur le bouton CVBS et maintenez-le enfoncé pendant 5 secondes pour passer à la
sortie vidéo composite (mode installation).
Remarque : L'AXIS Q1755 reste en mode installation pendant deux (2) minutes et revient
ensuite automatiquement en mode vidéo en composantes. Si vous avez besoin de plus de
temps, rappuyez sur le bouton.
4. Mettez la caméra en place et vérifiez que la zone désirée est
visible à l'écran.
5. Débranchez l'écran de contrôle.
FRAN
Ç
AIS
Sortie vidéo en composantes (en option)
Procédez comme suit pour voir le signal vidéo directement sur un
écran de contrôle HDTV connecté.
1. Suivez les instructions de la section Branchement des câbles, à la page 19.
2. Branchez l'AXIS Q1755 directement sur un écran HDTV à l'aide d'un câble vidéo en
composantes connecté aux connecteurs de sortie vidéo Y/Pb/Pr.
Une fois les câbles connectés, passez à la section Attribution d'une adresse IP, à la page 20.
Page 20 AXIS Q1755 Guide d'installation
Attribution d'une adresse IP
Aujourd'hui, la plupart des réseaux sont équipés d’un serveur DHCP qui attribue automatiquement
des adresses IP aux périphériques connectés. Si votre réseau en est dépourvu, votre AXIS Q1755
utilisera 192.168.0.90 comme adresse IP par défaut.
Si vous souhaitez paramétrer une adresse IP statique, sous Windows nous recommandons
l'utilisation de l'application AXIS IP Utility ou de l'application AXIS Camera Management. Selon le
nombre de caméras à installer, choisissez la méthode qui vous convient le mieux.
Ces deux applications gratuites sont disponibles sur le CD de la caméra vidéo sur IP Axis fourni avec
ce produit. Vous pouvez également les télécharger à partir du site www.axis.com/techsup.
Méthode Recommandée pour Système
d'exploitation
AXIS IP Utility
Voir page 21
AXIS Camera Management
Voir page 22
Remarques :
• En cas d'échec de l'attribution d'adresse IP, vérifiez qu'aucun pare-feu ne bloque l'opération.
• Pour connaître les autres méthodes d’attribution ou de détection de l'adresse IP de votre AXIS Q1755,
par exemple sous d'autres systèmes d'exploitation, reportez-vous à la page 25.
Une seule caméra
Petites installations
Plusieurs caméras
Grandes installations
Installation sur un autre sousréseau
Windows
Windows 2000
Windows XP Pro
Windows 2003 Server
Windows Vista
AXIS Q1755 Guide d'installation Page 21
AXIS IP Utility - Une seule caméra/petite installation
AXIS IP Utility recherche et affiche automatiquement les périphériques Axis sur votre réseau. Cette
application sert également à attribuer manuellement une adresse IP statique.
Notez que l'ordinateur exécutant l'application AXIS IP Utility doit se trouver sur le même segment
de réseau (sous-réseau physique) que l’AXIS Q1755.
Détection automatique
1. Vérifiez que l’AXIS Q1755 est connectée au réseau et sous tension.
2. Lancez AXIS IP Utility.
3. Lorsque l'icône de la caméra apparaît dans la fenêtre, double-cliquez dessus pour ouvrir la page
d'accueil correspondante.
4. Reportez-vous à la page 23 pour savoir comment configurer le mot de passe.
FRAN
Ç
AIS
Attribution manuelle de l'adresse IP (facultatif)
1. Trouvez une adresse IP non utilisée sur le même segment de réseau que celui de votre
ordinateur.
2. Sélectionnez AXIS Q1755 dans la liste.
3. Cliquez sur le bouton Assign new IP address to the selected device (Attribuer une
nouvelle adresse IP au périphérique sélectionné) et saisissez l'adresse IP.
4. Cliquez sur le bouton Assign (Attribuer) et suivez les instructions affichées à l'écran. La caméra
doit être redémarrée dans les 2 minutes pour que la nouvelle adresse IP soit prise en compte.
5. Cliquez sur le bouton Home Page (Page d'accueil) pour accéder aux pages Web de la caméra.
6. Reportez-vous à la page 23 pour savoir comment configurer le mot de passe.
Page 22 AXIS Q1755 Guide d'installation
AXIS Camera Management - Plusieurs caméras/grandes installations
AXIS Camera Management peut détecter automatiquement plusieurs périphériques Axis, afficher
l'état de connexion, gérer les mises à niveau du micrologiciel et configurer les adresses IP.
Détection automatique
1. Vérifiez que la caméra est connectée au réseau et sous tension.
2. Lancez AXIS Camera Management. Lorsque l'AXIS Q1755 apparaît dans la fenêtre, cliquez sur le
lien avec le bouton droit de la souris et sélectionnez Live View Home Page (Page d'accueil –
Vidéo en direct).
3. Reportez-vous à la page 23 pour savoir comment configurer le mot de passe.
Attribution d'une adresse IP à un seul périphérique
1. Sélectionnez AXIS Q1755 dans l'application AXIS Camera
Management, puis cliquez sur le bouton Assign IP (Attribuer
une adresse IP).
2. Sélectionnez Assign the following IP address (Attribuer
l'adresse IP suivante) et saisissez l’adresse IP, le masque de
sous-réseau et le routeur par défaut que le périphérique
utilisera.
3. Cliquez sur le bouton OK.
Attribution d'adresses IP à plusieurs périphériques
AXIS Camera Management accélère le processus d’attribution
d'adresses IP à plusieurs périphériques en suggérant des adresses IP
parmi une plage spécifiée.
1. Sélectionnez les périphériques à configurer (il peut s'agir de
plusieurs modèles), puis cliquez sur le bouton Assign IP
(Attribuer une adresse IP).
2. Sélectionnez Assign the following IP address range (Attribuer
la plage d'adresses IP suivante) et saisissez la plage d'adresses
IP, le masque de sous-réseau et le routeur par défaut que les périphériques utiliseront.
3. Cliquez sur le bouton OK.
AXIS Q1755 Guide d'installation Page 23
Pour configurer directement le mot de
passe via une connexion cryptée,
saisissez le mot de passe à cet endroit.
Pour créer une connexion HTTPS,
cliquez sur ce bouton.
Configuration du mot de passe
Pour accéder au produit, le mot de passe par défaut de l’administrateur, root, doit être configuré.
Vous pouvez effectuer cette opération dans la boîte de dialogue Configure Root Password
(Configurer le mot de passe root) qui s'affiche lors du premier accès à l’AXIS Q1755.
Pour éviter les écoutes électroniques lors de la configuration du mot de passe root, utilisez une
connexion HTTPS cryptée nécessitant un certificat HTTPS (voir la remarque ci-dessous).
Pour configurer le mot passe avec une connexion HTTP standard, saisissez directement le mot de
passe dans la première boîte de dialogue représentée ci-dessous.
Pour configurer le mot passe avec une connexion HTTPS cryptée, procédez comme suit :
1. Cliquez sur le bouton Create self-signed certificate (Créer un certificat autosigné).
2. Saisissez les informations demandées, puis cliquez sur OK. Le certificat est créé et le mot de
passe peut maintenant être configuré en toute sécurité. Tout le trafic vers et depuis l’AXIS
Q1755 est désormais crypté.
3. Saisissez un mot de passe, puis saisissez-le de nouveau pour confirmation. Cliquez sur OK. Le
mot de passe est maintenant configuré.
FRAN
Ç
AIS
4. Pour vous connecter, saisissez le nom d’utilisateur « root » dans la boîte de dialogue à l’invite.
Remarque : le nom d’utilisateur par défaut de l'administrateur est root et il ne peut pas être
supprimé.
5. Saisissez le mot de passe configuré ci-dessus et cliquez sur OK.
Loading...