Avaya E7S-7S Expansion Module Supplement User Manual

E7S/7S Expansion Module

Supplement

Part No. 304137-A Rev. 00 November 1998

4401 Great America Pa rkw ay 8 Federal S treet Santa Clara, CA 95054 Billerica, MA 01821

and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full re spo nsibility fo r th eir a pplic a tio ns of any products specified in th is d ocume nt . The information in this document is proprietary to Bay Networks, Inc.

Trademarks

AN, Quick2Config, and Bay Networks are registered trademarks and Advanced Remote Node, ANH, ARN, ASN, BayRS, BayStack, BayStream, BCC, and the Bay Networks logo are trademarks of Bay Networks, Inc.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, Bay Networks, Inc. reserves the right to make changes to the pr oducts described in this document without notice.

Bay Networks, Inc. does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.

USA Requirements Only

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reaso nable protection against harmful interferenc e when the equipment is operated in a commercial environment. This equipment ge nerates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to take whatever measures may be necessary to correct the interference at their own expense.

European Requirements Only

EN 55 022 Statement

This is to certify that the Bay Networks E7S/7S Expansion Module is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class A (CISPR 22).

Warning: This is a Class A product. In a domestic env iron m ent, this product may cause radio interference, in which case, the user may be required to take appropriate measures.

EC Declaration of Conformity

This product conforms (or these products conform) to the provisions of Council Directive 89/336/EEC and 73/23/EEC. The Declaration of Conformity is available on the Bay Networks World Wide Web site at www.baynetworks.com.

304137-A Rev. 00

Japan/Nippon Requirements Only

Voluntary Control Council for Interference (VCCI) Statement

This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

Canada Requirements Only

Canadian Department of Communications Radio Interference Regulations

This digital apparatus (E7S/7S Expansion Module) does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.

Règlement sur le brouillage radioélectrique du ministère des Communications

Cet appareil numérique (E 7S/7S Expan sion Mod ule) resp ecte les l imites de brui ts radioé lectrique s visan t les appa reils numériques de classe A prescrites dans le Règl ement sur le brouillage radioélectrique du ministère des Communications du Canada.

Canada CS-03 Rules and Regulations

Notice: The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunications netw ork prote cti ve, opera tional and safety re quirements as pres cribed in the app ropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, u sers shou ld e nsure that it is permissible to be connected to the fa cilitie s of t he lo cal telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent the degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the su pplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment .

Users should ensure for their own protection tha t the electrical gro und connecti ons of the po wer utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

Notice: For equipment using loopstart lines, please note that the Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement

304137-A Rev. 00

iii

that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. The REN is located on the “FCC Rules Part 68” label located on the bracket of the module, or on the back of the unit.

Canada CS-03 -- Règles et règlements

Avis: L'étiquette d'Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d'exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n'assure toutefois pas que le matériel fonctionnera à la satisfaction de l'utilisateur.

Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de le raccorder aux installations de l'entreprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de raccordement. L'abonné ne doi t pas oublier qu'il est possible que la conformité aux conditio ns énoncées ci-dessus n'empêche pas la dégradation du service dans certaines s it uations.

Les réparations de matériel homologué doivent être coordonnées par un représentant désigné par le fournisseur. L'entreprise de télécomm unication s pe ut d emande r à l' utilisat eur de débra ncher u n app areil à la su ite de rép arations o u de modifications effectuées par l'utilisateur ou à cause de mauvais fonctionnement.

Pour sa propre protectio n, l 'utilisateur doit s'assurer que tous les f ils d e mise à la te rre de la sou rce d 'éner gie électriqu e, des lignes téléphoniques et des canalisations d'eau métalliques, s'il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.

Avertissement: L'utilisateur ne doit p as t ente r d e fa ire ce s ra cco rdem ents lu i-m ê me; i l do it avoir recours à un service d'inspection des installati ons électriques, ou à un électricien, selon le cas.

Avis: Veuillez prendre note que pour tout appareillage supportant des lignes de type “loopstart,” l'indice d'équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d'une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition q ue la somme d'indi ces d'équi v alence de la sonnerie de to us les dispositifs n' excède p as

5. Le REN figure sur l’étiquette “FCC Rules Part 68” située sur le support du module ou à l’arrière de l’unité.

FCC Part 68 Compliance Statement

This equipment complies with Pa rt 68 of FCC Ru les. All dire ct c onnec tio ns to telep hone ne tw o r k line s mu st be mad e using standard plugs and jacks compliant with FCC Part 68. Please note the following:

1. You are required to request service from the telephone company before you connect the unit to a network. When you request service, you must pro vide the teleph on e compa ny with the following data:

• When you request T1 Service, you must provide the telephone company with

-- The Facility Interface Code Provide the telephone company with all the codes below:

- 04DU9-BN (1.544 MB, D4 framing format)

- 04DU9-DN (1.544 MB, D4 framing format with B8ZF coding)

- 04DU9-1KN (1.544 MB, ESF framing format)

- 04DU9-1SN (1.544 MB, ESF framing format with B8ZF coding)

- 04DU9-1ZN (1.544 MB, ANSI ESF and ZBTSI without line power) The telephone company will select the code it has available.

-- The Service Order Code(s) (SOC): 6.0F

-- The req uired Universal Service Order Code (USOC) jack: RJ48C

• When you request 56K/64K Service, you must provide the telephone company with

-- The Facility Interface Code: 04DU5-56/64

-- The Service Order Code(s) (SOC): 6.0F

-- The req uired Universal Service Order Code (USOC) jack: RJ48S

304137-A Rev. 00

• When you request V.34 Service, you must provide the telephone company with

-- The req uired Universal Service Order Code (USOC) jack: RJ11C

-- The make, model number, Ringer Equivalence Number (REN), and FCC Registration number of the unit

The REN helps you determine the number of devices you can connect to your telephone line and still have all of those devices ring when your number is called. In most, but not all, areas, the sum of the RE Ns of all devices should not exceed 5.0. To be certain of the number of devices you can connect to your line, you should call your local telephone company to determine the maximum REN for your calling area.

• When you reque s t ISD N “U” I nterface Service, you must provide the teleph on e c om pa ny with

-- The Facility Interface Code: 02IS5

-- The Service Order Code(s) (SOC): 6.0F

-- The req uired Universal Service Order Code (USOC) jack: RJ49C

• When you request ISDN “S/T” Interface Service, you must provide the telephone company with

-- The Service Order Code(s) (SOC): 6.0N

-- The ma ke, model number, and FCC Registration number of the NT1

Note: ISDN S/T cannot be directl y connected to the network.

• When you request Primary Rate ISDN Service, you must provide the telephone company with

-- The Facility Interface Code: 04DU9-1SN (1.544 MB, ESF framing format with B8ZF coding)

-- The Service Order Code(s) (SOC): 6.0F

-- The req uired Universal Service Order Code (USOC) jack: RJ48C

2. Your telephone company may make changes to its facilities, equipment, operations, or procedures that could affect the proper function in g of yo ur equip m ent. The teleph on e com pany will notify you in advance of such changes to give you an opportunity to maintain uninterrupted telephone service.

3. If the unit causes harm to the telephone network, the telephone company may temporarily discontinue your service. If possible, they will notify you in advance, but if advance notice is not practical, you will be notified as soon as possible and will be informed of your right to file a complaint with the FCC.

4. If you experience trou ble with the unit, ple ase contac t the Bay Netw orks Technical Solutions Center in your area for service or repairs. Repairs should be performed only by service personnel authorized by Bay Networks, Inc.

United States 1-800-2LAN-WAN Valbonne, France 33-4-92-96-69-68 Sydney, Australia 61-2-9927-8800 Tokyo, Japan 81-3-5402-0180

5. You are required to notify the telephone company when you disconnect the unit from the network.

304137-A Rev. 00

+ 9 hidden pages