Part No. 306661-A Rev 00
January 2000
4401 Great America Parkway
Santa Clara, CA 95054
Dual Synchronous PMC
Module
Supplement
Copyright © 2000 Nortel Networks
All rights reserved. Printed in the USA. January 2000.
The information in this document is subject to change without notice. The statements, configurations, technical data,
and recommendations in this document are believed to be accurate and reliable, but are presented without express or
implied warranty. Users must take full respo nsib ility fo r th e ir app lica tio ns o f a ny products specified in this d ocume nt .
Trademarks
NORTEL NETWORKS is a trademark of Nortel Networks.
Bay Networks, ACE, AFN, AN, BCN, BLN, BN, BNX, CN, FRE, LN, Optivity, Optivity Policy Services, and PPX
are regi ster ed t rade mark s and Adv an ced Remo te Nod e, A NH, AR N, ASN, B ayRS , Ba ySecu re, BaySt ack , BaySt rea m,
BCC, BCNX, BLNX, Centillion, EtherSpeed, FN, IP AutoLearn, Passport, SN, SPEX, Switch Node, System 5000,
and TokenSpeed are trademarks of Nortel Networks.
Microsoft, MS, MS-DOS, Win32, Windows, and Windows NT are registered trademarks of Microsoft Corporation.
All other trademarks and registered trademarks are t he property of their respective owners.
Statement of Conditions
In the interest of improvi ng internal design, operational function, and/o r relia bi lity, Nortel Network s NA Inc. reserves
the right to make changes to the products described in this document without notice.
Nortel Networks NA Inc. does not assume any liability that may occur due to the use or application of the product(s)
or circuit layout(s) described her ein.
USA Requirements Only
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment ge nerates, uses, and can radiate radio
frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case users will be required to take whatever measures may be necessary to correct the
interference at their own expense.
European Requirements Only
EN 55 022 Statement
This is to certify that the Norte l Networks Dual Synchronous PMC Module is shield ed ag a inst the generation of radio
interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared
by the application of EN 55 022 Class A (CISPR 22).
Warning: This is a Class A product. In a domestic env iron m ent, this product may cause radio interference, in which
case, the user may be required to take appropriate measures.
Achtung: Dieses ist ein Gerät der Funkst örgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes
Rundfunkstörungen auftreten, in welchen Fällen der Benutzer für entsprechende Gegenmaßnahmen verantwortlich
ist.
Attention: Ceci est un produit de Classe A. Dans un environnement domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l’utilisateur de prendre les mesures spécifiques appropriées.
ii
306661-A Rev 00
Japan/Nippon Requirements Only
Voluntary Control Council for Interference (VCCI) Statement
Taiwan Requirements
Bureau of Standards, Metrology and Inspection (BSMI) Statement
Canada Requirements Only
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (Du al Sy nch ron ou s P MC Mo du le) d oes n ot exceed the Class A limits for radio -no ise e m ission s
from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numér ique (Dual Synchronous PMC Module ) respecte les limit e s de bruits radioélectriques visant les
appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des
Communications du Canada.
306661-A Rev 00
iii
Canada Requirements Only
Canada CS-03 Rules and Regulations
Notice: The Industry Canada label identifies certified equipment. This certification means that the equipment meets
telecommunications netw ork prote cti ve, opera tional and safety re quirements as pres cribed in the app ropriate Terminal
Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to
the user’s satisfaction.
Before installing this equipment, u sers shou ld e nsure that it is permissible to be connected to the faci lities of t he local
telecommunications company. The equipment must also be installed using an acceptable method of connection. The
customer should be aware that compliance with the above conditions may not prevent the degradation of service in
some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or
alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment .
Users should ensure for their own protection tha t the electrical gro und connecti ons of the po wer utility, telephone lines
and internal metallic water pipe system, if present, are connected together. This precaution may be particularly
important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric
inspection authority, or electrician, as approp ria te.
Notice: For equipment using loopstart lines, please note that the Ringer Equivalence Number (REN) assigned to each
terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination of devices subject only to the requirement
that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. The REN is located on the “FCC
Rules Part 68” label located on the bracket of the module, or on the back of the unit.
Canada CS-03 -- Règles et règlements
Avis: L'étiquette d'Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est
conforme aux normes de protection, d'exploitation et de sécurité des réseaux de télécommunications, comme le
prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n'assure
toutefois pas que le matériel fonctionnera à la satisfaction de l'utilisateur.
Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de le raccorder aux installations de l'entreprise
locale de télécommunication. Le matériel doit également être i nst allé en suivant une méthode acceptée de
raccordement. L'abonné ne doi t pas oublier qu'il est possible que la conformité aux conditio ns énoncées ci-dessus
n'empêche pas la dégradati on du service dans certaines situations.
Les réparations de matériel homologué doivent être coordonnées par un représentant désigné par le fournisseur.
L'entreprise de télécomm unication s pe ut d emande r à l' utilisat eur de débra ncher u n app areil à la su ite de rép arations o u
de modifications effectuées par l'utilisateur ou à cause de mauvais fonctionnement.
Pour sa propre protectio n, l 'utilisateur doit s'assurer que tous les f ils d e mise à la te rre de la sou rce d 'éner gie électriqu e,
des lignes téléphoniques et des canalisations d'eau métalliques, s'il y en a, sont raccordés ensemble. Cette précaution
est particulièrement importante dans les régions rurales.
Avertissement: L'utilisateur ne doit p as tente r d e f aire c es racco rde m ents lu i-mê me; i l do it avoir recours à un service
d'inspection des installati ons électriques, ou à un électricien, selon le cas.
Avis: Veuillez prendre note que pour tout appareillage supportant des lignes de type “loopstart,” l'indice d'équivalence
de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être
raccordés à une interface. La terminaison d'une interface téléphonique peut consister en une combinaison de quelques
dispositifs, à la seule condition q ue la somme d'indi ces d'équi v alence de la sonnerie de to us les dispositifs n' excède p as
5. Le REN figure sur l’étiquette “FCC Rules Part 68” située sur le support du module ou à l’arrière de l’unité.
(continued)
iv
306661-A Rev 00
FCC Part 68 Compliance Statement
This equipment complies with Pa rt 68 of FCC Ru les. All dire ct c onnec tio ns to telep hone ne tw o r k line s mu st be mad e
using standard plugs and jacks compliant with FCC Part 68. Please note the following:
1. You are required to request service from the telephone company before you connect the unit to a network. When
you request service, you must pro vide the teleph on e compa ny with the following data:
• When you request T1 Service, you must provide the telephone company with
-- The Facility Interface Code
Provide the telephone company with all the codes below:
- 04DU9-BN (1.544 MB, D4 framing format)
- 04DU9-DN (1.544 MB, D4 framing format with B8ZF coding)
- 04DU9-1KN (1.544 MB, ESF framing format)
- 04DU9-1SN (1.544 MB, ESF framing format with B8ZF coding)
- 04DU9-1ZN (1.544 MB, ANSI ESF and ZBTSI without line power)
The telephone company will select the code it has available.
-- The Service Order Code(s) (SOC): 6.0F
-- The req uired Universal Service Order Code (USOC) jack: RJ48C
2. Your telephone company may make changes to its facilities, equipment, operations, or procedures that could
affect the proper function in g of yo ur equip m ent. The teleph on e com pany will notify you in advance of such
changes to give you an opportunity to maintain uninterrupted telephone service.
3. If the unit causes harm to the telephone network, the telephone company may temporarily discontinue your
service. If possible, they will notify you in advance, but if advance notice is not practical, you will be notified
as soon as possible and will be informed of your right to file a complaint with the FCC.
4. If you experience trouble with the unit, pl ease contact the Nortel Networks Technical Solutions Center in
your area for service or rep a irs. Repairs should be pe rformed only by service personnel authorized by
Nortel Networks.
United States 1-800-2LANWAN
Valbonne, France 33-4-92-96-69-68
Sydney, Australia 61-2-9927-8800
Tokyo, Japan 81-3-5740-1700
5. You are require d to notify the telephone company when you disconnect the un it from the network.
Nortel Networks NA Inc. Software License Agreement
NOTICE: Please carefully read this license agre ement before copying or using the accompanying software or
installing the hardware unit with pre-enabled software (each of which is referred to as “Software” in this Agreement).
BY COPYING OR USING THE SOFTWARE, YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF
THIS LICENSE AGREEMENT. THE TERMS EXPRESSED IN THIS AGREEMENT ARE THE ONLY TERMS
UNDER WHICH NORTEL NETWORKS WILL PERMIT YOU TO USE THE SOFTWARE. If you do not accept
these terms and conditions, return the product, unused and in the original shipping container, within 30 days of
purchase to obtain a credit for the full purchase price.
1. License Grant. Nortel Networks NA Inc. (“Nortel Networks”) grants the end user of the Software (“Licensee”) a
personal, nonex clusive, nontransferable license : a) to us e the So ftw are eit her on a single c omputer o r, if applicable, on
a single authorized device identified by host ID, for which it was originally acquired; b) to copy the Software solely
for backup purposes in support of authorized use of the Software; and c) to use and copy the associated user manual
solely in support of authoriz ed use of th e Softwa re b y Licen see. Thi s license applies t o the So ftware o nly and d oes not
extend to Nortel Networks Agent software or other Nortel Networks software products. Nortel Networks Agent
306661-A Rev 00
v
software or other Nortel Networks software products are licensed for use under the terms of the applicable N ortel
Networks NA Inc. Software License Agreement that accompanies such software and upon payment by the end user of
the applicable license fees for such software.
2. Restrictions on use; reservation of rights. The Software and user manuals are protected under copyright laws.
Nortel Networks and/or its licensors retain all title and ownership in both the Software and user manuals, including
any revisions made by Nortel Networks or its licensors. Th e copyright notice must be r e produced and incl uded with
any copy of any portion of the Software or user manuals. Licensee may not modify, translate, decompile, disassemble,
use for any competitive analysis, reverse engineer, distribute, or create derivative works from the Software or user
manuals or any copy , in whole or in part. Except as expressly provided in this Agreement, Licensee may not copy or
transfer the Software or user manuals, in whole or in part. The Software and user manuals embody Nortel Networks’
and its licensors’ confidential and proprietary intellectu al pro p erty. Licensee shall not sublicense, assign, or ot herwise
disclose to any third party the Software, or any information about the operation, design, performance, or
implementation of the Software and user manuals that is confidential to Nortel Networks and its licensors; however,
Licensee may grant permission to its consultants, subcontractors, a nd agents to use the Softw are at Licensee’s facility,
provided they have agreed to use the Software only in accordance with the terms of this license.
3. Limited warranty . Nortel Networks warrants each item of Software, as delivered by Nortel Networks and properly
installed and operated on Nortel Networks hardware or other equipment it is originally licensed for, to function
substantially as described in its accompanying user m anual during its warranty period , which begins on the date
Software is first shipped to Licensee. If an y item of S oftware f ails to so function d uring its w arranty period, as the sole
remedy Nortel Networks will at its discretion provide a suitable fix, patch, or workaround for the problem that may be
included in a future Software release. Nortel Networks further warrants to Licensee that the media on which the
Software is provided will be free from defec ts in materials and wo rkman ship under no rmal use for a peri od of 90 da ys
from the date Software is first shipped to Licensee. Nortel Networks will replace defective media at no charge if it is
returned to Nortel Netw orks during the warranty period along with proof of the date of sh ipment. This warrant y does
not apply if the media has been damaged as a result of accident, misuse, or abuse. The Licensee assumes all
responsibility for selection of the Software to achieve Licensee’s intended results and for the installation, use, and
results obtained from the Software. Nortel Networks does not warrant a) that the functions contained in the software
will meet the Licensee’s requirements, b) that the Software will operate in the hardware or software combinations that
the Licensee may select, c) that the operation of the Software will be uninterrupted or error free, or d) that all defects
in the operation of the Softw are will be corrected . Nortel Network s is not obligate d to remedy an y Software defect that
cannot be reproduced with the latest Software release. These warranties do not apply to the Software if it has been (i)
altered, except by Nortel Networks or in accordance with i ts instructions; (ii) used in conj unction with another
vendor’s product, resulting in the de fect; or (iii) damaged by improper environment, abuse, misuse , accident, or
negligence. THE FOREGOING WARRANTIES AND LIMITATIONS ARE EXCLUSIVE REMEDIES AND ARE
IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Licensee is respo nsib le
for the security of its own data and information and for maintaining adequate procedures apart from the Software to
reconstruct lost or altered files, data, or programs.
4. Limitation of liability. IN NO EVENT WILL NORTEL NETW ORKS OR ITS LICENS OR S BE LIABLE FOR
ANY COST OF SUBSTITUTE PROCUREMENT; SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES; OR ANY DAMAGES RESULTING FROM INACCURATE OR LOST DATA OR LOSS OF USE OR
PROFITS ARISING OUT OF OR IN CONNECTION WITH THE PERFORMANCE OF THE SOFTWARE, EVEN
IF NORTEL NETWORKS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT
SHALL THE LIABILITY OF NORTEL NETWORKS RELATING TO THE SOFTWARE OR THIS AGREEMENT
EXCEED THE PRICE PAID TO NORTEL NETWORKS FOR THE SOFTWARE LICENSE.
5. Government Licensees. This provision applies to a ll Softwa re and docum entation acquired d irectly or i ndirectly by
or on behalf of the United States Government. The Software and documentation are commercial products, licensed on
the open market at market prices, and were developed entirely at private expense and without th e use of any U.S.
Government funds. The license to the U.S. Government is granted only with restricted rights, and use, duplication, or
disclosure by the U.S. Government is subject to the restrictions set forth in subparagraph (c)(1) of the Commercial
Computer Software––Restricte d Rig hts cla u se o f FAR 52.227-19 and the limitations set out in this license for civilian
vi
306661-A Rev 00
agencies, and subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause of DFARS
252.227-7013, for agencies of t he Department of Defense or their successors, whichever is applicable.
6. Use of Software in the European Community. This provision applies to all Software acquired for use within the
European Community. If Licensee uses the Software within a country in the European Community, the Software
Directive enacted by the Council of European Communities Directive dated 14 May, 1991, will apply to the
examination of the Software to facilitate interoperability. Licensee agrees to notify Nortel Networks of any such
intended examination of the Software an d may procure support and assista nce from Nortel Networks.
7. Term and termination. This license is effective until terminated; howeve r, all of the restrictions with respect to
Nortel Networks’ copyright in the Software and user manuals will cease being effective at the date of expiration of the
Nortel Networks copyright; those restrictions relating to use and disclosure of Nortel Networks’ confidential
information shall continue in effect. Licensee may terminate this license at any time. The license will automatically
terminate if Licensee fails to comply with any of the terms and conditions of the license. Upon termination for any
reason, Licensee will immediat ely destroy or return to Nortel Networks the Software, user manuals, and all copies.
Nortel Networks is not liable to Licensee for damages in any form solely by reason of the termination of this license.
8. Export and Re-export. Licensee agrees not to export, directly or indirectly, the Software or related technical data
or information without first obtaining any required export licenses or other governmental approvals. Without limiting
the foregoing, Licensee, on behalf of itself and its subsidiaries and affiliates, agrees that it will not, without first
obtaining all export licenses and approvals required by the U.S. Government: (i) export, re-export, transfer, or divert
any such Software or technical data, or any direct product thereof, to any country to which such exports or re-exports
are restricte d or em b argoed under United State s e x port control laws and re gulations, or to any nation al or re sident of
such restricted or embargoed countries; or (ii) provide the Software or related technical data or information to any
military end user or for any military end use, including the design, development, or production of any chemical,
nuclear, or biological weapons.
9. General. If any provision of this Agreement is held to be invalid or unenf orceable by a court of competent
jurisdiction, the remainder of the provisions of this Agreement shall remain in full force and effect. This Agreement
will be governed by the laws of the state of California.
Should you have any questions concerning this Agreement, contact Nortel Netw orks, 4401 Great America Parkway,
P.O. Box 58185, Santa Clara, California 95054-8185.
LICENSEE ACKNOWLEDGES THAT LICENSEE HAS READ THIS AGREEMENT, UNDERSTANDS IT, AND
AGREES TO BE BOUND BY ITS TERMS AND CONDITIONS. LICENSEE FURTHER AGREES THAT THIS
AGREEMENT IS THE ENTIRE AND EXCLUSIVE AGREEMENT BETWEEN NORTEL NETWORKS AND
LICENSEE, WHICH SUPERSEDES ALL PRIOR ORAL AND WRITTEN AGREEMENTS AND
COMMUNICATIONS BETWEEN THE PARTIES PERTAINING TO THE SUBJECT MATTER OF THIS
AGREEMENT. NO DIFFERENT OR ADDITIONAL TERMS WILL BE ENFORCEABLE AGAINST NORTEL
NETWORKS UNLESS NORTEL NETWORKS GIVES ITS EXPRESS WRITTEN CONSENT, INCLUDING AN
EXPRESS WAIVER OF THE TERMS OF THIS AGREEMENT.
306661-A Rev 00
vii
Contents
Preface
Before You Begin ............................................................................................................. xv
Text Conventions .............................................................................................................xvi
Acronyms ........................... .......................... .......................... ......................... .................xvi
Hard-Copy Technical Manuals .................................. ...... ....... ...... ...... ..............................xvi
How to Get Help .............................................................................................................xvii
Chapter 1
Using the Dual Synchronous PMC Module
Installing the Dual Synchronous PMC Module ...............................................................1-1
Attaching Cables ............................................................................................................1-5
Interpreting LEDs ...........................................................................................................1-6
Completing Software Configuration ................................................................................1-7
306661-A Rev. 00
ix
Figures
Figure 1-1. Removing the PMC Module Filler Panel ..................................................1-2
Figure 1-2. Installing the Dual Synchronous PMC Module .........................................1-3
Figure 1-3. Securing the PMC Module to the Expansion Card ..................................1-4
Figure 1-4. Dual Synchronous PMC Module Cable Connection ................................1-5
Figure 1-5. Dual Synchronous PMC Module LEDs ....................................................1-6
306661-A Rev. 00
xi
Tables
Table 1-1. Dual Synchronous PMC Module LED Functions .....................................1-6
306661-A Rev. 00
xiii
The Dual Synchronous PMC Modul e contains two full-dupl ex synchronous serial
ports to provide Circuit Emulation Service (CES) over the WAN.
In this guide, the P asspor t™ 5430 Mult iservice Access Switch i s referre d to as the
Passport 5430.
Before You Begin
This guide is intended for qualified service personnel who are installing the
Passport 5430 for the fi rst time or who need to install or rep lace any Passport 5430
customer-replaceable unit (CRU). A qualified service person should have
appropriate technical training and experience and be aware of the hazards
involved in installing and replacing CRUs.
Preface
306661-A Rev 00
Before installing the Passport 5430, ensure that all network wiring has been
installed on the premises using standard cable-system practices.
Before turning on the Passport 5430 for the first time, contact your network
administrator to determine which software configuration option to use.
xv
Dual Synchronous PMC Module
Text Conventions
This guide uses the following text conventions:
Supplement
bold text
italic text Indicates new terms, book titl es, and variables in
Indicates command names and options and text that
you need to enter.
Example: Enter the
command syntax descriptions.
Acronyms
This guide uses the following acronyms:
CRU customer-replaceable unit
IP Internet P rotocol
LED light emitting diode
Hard-Copy Technica l Manuals
You can print selected technical manuals and release notes free, directly from the
Internet. Go to support.baynetworks.com/library/tpubs/. Find the product for
which you need documentation. Then locate the specific category and model or
version for your hardw are or soft ware product . Usi ng Adobe Ac robat Re ader, you
can open the manuals and releas e notes, search for the sections you ne ed, and print
them on most standard printers. You can download Acrobat Reader free from the
Adobe Systems Web site, www.adobe.com.
diags
command.
xvi
306661-A Rev 00
You can purchase selected documentation sets, CDs, and technical publications
through the collateral catalog. The catalog is located on the World Wide Web at
support.baynetworks.com/catalog.html and is divided into sections arranged
alphabetically:
• The “CD ROMs” section lists available CDs.
• The “Guides/Books” section lists books on technical topics.
• The “Technical Manuals” section lists available printed documentation sets.
How to Get Help
If you purchased a service contract for your Nortel Networks product from a
distributor or authorized reseller, contact the technical support staff for that
distributor or reseller for assistance.
If you purchased a Nort el Net wor ks ser vice pr ogram, c ontact one of the f ollowing
Nortel Networks Technical Solutions Centers:
Preface
Technical Solutions Center Telephone Number
Billerica, MA 800-2LANWAN (800-252-6926)
Santa Clara, CA 800-2LANWAN (800-252-6926)
Valbonne, France 33-4-92-96-69-68
Sydney, Australia 61-2-9927-8800
Tokyo, Japan 81-3-5740-1700
306661-A Rev 00
xvii
Chapter 1
Using the Dual Synchronous PMC Module
This document supplements Installing and Operating the Passport 5430
Multiservice Access Switc h . F ol lo w the ha rdw are insta llat ion st eps in tha t manual ,
then refer to this document for information sp ecifi c to the Dual Synchr onous PMC
module.
Warning:
Passport 5430 Multiservice Access Switch only. Attempting to use the Dual
Synchronous PMC Module in any other product may be hazardous and
invalidates the regulatory approval.
The Dual Synchronous PMC module is designed to operate in the
Installing the Dual Synchronous PMC Module
To install a PMC module on the expansion card:
1.
Attach an antistatic wrist strap.
Caution:
antistatic wrist strap whenever you handle printed circuit boards.
2.
Electrostatic discharge can damage hardware. You must wear the
If the expansion slot contains a filler panel, push it out from behind the
card bezel (Figure 1-1)
.
306661-A Rev 00
1-1
Dual Synchronous PMC Module
Figure 1-1. Removing the PMC Module Filler Panel
Supplement
Expansion Card
FBR0058A
1-2
3.
Holding the Dual Synchronous PMC Module with the connectors facing
down, slide it into the opening on the expansion card (Figure 1-2)
4.
Press down to seat the PMC module firmly into the sockets (Figure 1-2).
306661-A Rev 00
.
Using the Dual Synchronous PMC Module
Expansion Card
PMC
module
openings
FBR0006A
Figure 1-2. Installing the Dual Synchronous PMC Module
306661-A Rev 00
5.
Flip the expansion card upside down so that the component side is facing
down (Figure 1-3)
.
1-3
Dual Synchronous PMC Module
6.
Insert and tighten the scr ews to se cur e the PMC module to the expansio n
card (Figure 1-3)
Supplement
.
1-4
Expansion Card
Figure 1-3. Securing the PMC Module to the Expansion Card
7.
Install the expansion card into the chassis.
For instructions, see Installing an Expansion Card in the Passport 5430
Multiservice Access Switch.
306661-A Rev 00
FBR0007A
Attaching Cables
You install the Dual Synchronous PMC Module onto the expansion card . See
Installing an Expan sion Ca rd in the Passport 5430 Multiservice Acces s Swit c h for
the complete installation procedure.
Using the Dual Synchronous PMC Module
Module 3
Module 4
Module 5
Remote
Console
U
ISDN BRI
withNT1
Telco
V.34 Modem
COM
COM
Voice Processor
Expansion Card
Expansion Card
Figure 1-4. Dual Synchronous PMC Module Cable Connection
System
Processor
PCI Slot 1
PCI Slot 2
PCI Slot 3
PCI Slot 4
FBR0077A
306661-A Rev 00
To attach the synchronous cable:
1.
Push the synchronous cable onto the connector on the installed Dual
Synchronous PMC Module (Figure 1-4)
2.
Tighten the captive screws.
.
1-5
Dual Synchronous PMC Module
Interpreting LEDs
Each Dual Synchronous PMC module has two LEDs (Figure 1-5).
Supplement
Port 1
Port 2
Module 3
Module 4
Module 5
Remote
Console
U
D
ISDN BRI
withNT1
RLSD
RLSD
Telco
V.34 Modem
B1
DD
B2
COM
Serial
COM
Serial
Tx
RLSD
Rx
DTR
5V FLASH ONLY
Module 2
Module 2 Module 1
Dsync
Module 2 Module 1
Dsync
Port 1
Port 2
Port 1
Port 2
Module 2 Module 1 Port 1
YEL
SYNC
ALM
RED
T1/E1
LOOP
ALM
Module 1
SYNC
Daul
T1/E1
LOOP
Dsync
Dsync
PCMCIA 1
PCMCIA 2
ATM
Port 2
TX/RX
SPD
Link
Console
YEL
ALM
RED
ALM
Port 1
Port 2
Port 1
Port 2
Voice Processor
YEL
SYNC
ALM
RED
LOOP
ALM
Expansion Card
Expansion Card
System
Processor
PS1
WAN
Run
PS2
Mod2
Boot
Fan
cPCI
Sys
Insert
Extract
Insert
Extract
Insert
Extract
PCI Slot 1
PCI Slot 2
PCI Slot 3
PCI Slot 4
FBR0086A
Figure 1-5. Dual Synchronous PMC Module LEDs
Table 1-1 describes the functions of the Dual Synchronous PMC module’s LEDs.
Table 1-1. Dual Synchronous PMC Module LED Functions
Label Color Meaning
Port 1 Green Lights when data ca rrier is detected.
Port 2 Green Lights when data ca rrier is detected.
1-6
306661-A Rev 00
Completing Software Configurat ion
Once you have successfully installed the Dual Synchronous PMC module,
complete the following software configuration tasks using instructions found in
the documentation:
Configuration Task Location of Instructions
Using the Dual Synchronous PMC Module
If this is a first-time installation, you must
quick-start your Passport 5430.
Modify the Passport 5430 configuration file
to add the Dual Synchronous PMC module
and enable default Dual Synchronous PMC
module software services.
Installing and Operating the Passport 5430
Multiservice Access Switch
• Configuring and Managing Rou ters with
Site Manager
• Using the Bay Command Console
(BCC)
For the latest information, be sure to review the release notes and documentation
change notice for your version of BayRS software.
306661-A Rev 00
1-7
Loading...